118 lines
3.0 KiB
Plaintext
118 lines
3.0 KiB
Plaintext
#
|
|
# For a description of the syntax of this configuration file,
|
|
# see the file kconfig-language.txt in the NuttX tools repository.
|
|
#
|
|
|
|
config EXAMPLES_FLOWC
|
|
bool "Serial flow control example"
|
|
default n
|
|
depends on SERIAL_TERMIOS
|
|
---help---
|
|
Enable the serial hardware flow control test.
|
|
|
|
Serial termios support must be enabled.
|
|
|
|
CONFIG_SERIAL_TERMIOS=y
|
|
|
|
In addtion, you will need these related serial driver settings (the
|
|
actual values of the watermark setting may be tuned to suit your
|
|
preferences)
|
|
|
|
CONFIG_SERIAL_IFLOWCONTROL=y
|
|
CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
|
|
CONFIG_SERIAL_IFLOWCONTROL_LOWER_WATERMARK=25
|
|
CONFIG_SERIAL_IFLOWCONTROL_UPPER_WATERMARK=75
|
|
|
|
And for the CDC/ACM driver in particular:
|
|
|
|
CONFIG_CDCACM_IFLOWCONTROL=y
|
|
|
|
There are hooks in place for output flow control but these have not
|
|
been exercised.
|
|
|
|
if EXAMPLES_FLOWC
|
|
|
|
config EXAMPLES_FLOWC_INPUT
|
|
bool "Verify input flow control"
|
|
default y
|
|
# depends on SERIAL_IFLOWCONTROL
|
|
|
|
config EXAMPLES_FLOWC_OUTPUT
|
|
bool "Verify output flow control"
|
|
default y
|
|
# depends on SERIAL_OFLOWCONTROL
|
|
|
|
config EXAMPLES_FLOWC_SENDER1
|
|
bool "Target1 is the sender"
|
|
default n
|
|
---help---
|
|
By default Target1 is the receiver and the host PC (or Target2) is
|
|
the sender. That is the configuration you would to test RX flow
|
|
control on the target.
|
|
|
|
config EXAMPLES_FLOWC_PROGNAME1
|
|
string "Target1 program name"
|
|
default "receiver" if !EXAMPLES_FLOWC_SENDER1
|
|
default "sender" if EXAMPLES_FLOWC_SENDER1
|
|
depends on BUILD_KERNEL
|
|
---help---
|
|
This is the name of the Target1 program that will be use when the
|
|
NSH ELF program is installed.
|
|
|
|
config EXAMPLES_FLOWC_PRIORITY1
|
|
int "Target1 task priority"
|
|
default 100
|
|
|
|
config EXAMPLES_FLOWC_STACKSIZE1
|
|
int "Target1 stack size"
|
|
default 2048
|
|
|
|
config EXAMPLES_FLOWC_TARGET2
|
|
bool "Second endpoint is a target"
|
|
default n
|
|
---help---
|
|
By default, the host PC is configured as the second endpoint of the
|
|
FLOWC test. If this option is selected, then the second endpoint
|
|
will be built into the FLASH image as well. This means that you
|
|
can use two target boards to run the test with no host PC
|
|
involvement.
|
|
|
|
if EXAMPLES_FLOWC_TARGET2
|
|
|
|
config EXAMPLES_FLOWC_PROGNAME2
|
|
string "Target2 program name"
|
|
default "receiver" if !EXAMPLES_FLOWC_RECEIVER2
|
|
default "sender" if EXAMPLES_FLOWC_RECEIVER2
|
|
depends on BUILD_KERNEL
|
|
---help---
|
|
This is the name of the Target2 program that will be use when the
|
|
NSH ELF program is installed.
|
|
|
|
config EXAMPLES_FLOWC_PRIORITY2
|
|
int "Target2 task priority"
|
|
default 100
|
|
|
|
config EXAMPLES_FLOWC_STACKSIZE2
|
|
int "Target2 stack size"
|
|
default 2048
|
|
|
|
endif # EXAMPLES_FLOWC_TARGET2
|
|
|
|
config EXAMPLES_FLOWC_RECEIVER_BUFSIZE
|
|
int "Receiver buffer size"
|
|
default 64
|
|
|
|
config EXAMPLES_FLOWC_RECEIVER_DELAY
|
|
int "Receiver read delay (msec)"
|
|
default 100
|
|
|
|
config EXAMPLES_FLOWC_RECEVER_DEVNAME
|
|
string "Default TTY device for receiver"
|
|
default "/dev/ttyACM0"
|
|
|
|
config EXAMPLES_FLOWC_SENDER_DEVNAME
|
|
string "Default TTY device for sender"
|
|
default "/dev/ttyACM0"
|
|
|
|
endif # EXAMPLES_FLOWC
|