nuttx/include/hex2bin.h

167 lines
6.1 KiB
C
Raw Permalink Normal View History

/****************************************************************************
* include/hex2bin.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __INCLUDE_HEX2BIN_H
#define __INCLUDE_HEX2BIN_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <stdio.h>
#ifdef CONFIG_LIBC_HEX2BIN
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/****************************************************************************
* Public Types
****************************************************************************/
/* Intel HEX data streams are normally in big endian order. The following
* enumeration selects other ordering.
*/
enum hex2bin_swap_e
{
HEX2BIN_NOSWAP = 0, /* No swap, stream is in the correct byte order */
HEX2BIN_SWAP16 = 1, /* Swap bytes in 16-bit values */
HEX2BIN_SWAP32 = 2 /* Swap bytes in 32-bit values */
};
/****************************************************************************
* Public Data
****************************************************************************/
#ifdef __cplusplus
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
/****************************************************************************
* Name: hex2bin
*
* Description:
* Read the Intel HEX ASCII data provided on the serial IN stream and write
* the binary to the seek-able serial OUT stream.
*
* These streams may be files or, in another usage example, the IN stream
* could be a serial port and the OUT stream could be a memory stream.
* This would decode and write the serial input to memory.
*
* Input Parameters:
* instream - The incoming stream from which Intel HEX data will be
* received.
* outstream - The outgoing stream in which binary data will be written.
* baseaddr - The base address of the outgoing stream. Seeking in the
* output stream will be relative to this address.
* endpaddr - The end address (plus 1) of the outgoing stream. This
* value is used only for range checking. endpaddr must
* be larger than baseaddr. A zero value for endpaddr
* disables range checking.
* swap - Controls byte ordering. See enum hex2bin_swap_e for
* description of the values.
*
* Returned Value:
* Zero (OK) is returned on success; a negated errno value is returned on
* failure.
*
****************************************************************************/
struct lib_instream_s;
struct lib_sostream_s;
int hex2bin(FAR struct lib_instream_s *instream,
FAR struct lib_sostream_s *outstream, unsigned long baseaddr,
unsigned long endpaddr, enum hex2bin_swap_e swap);
/****************************************************************************
* Name: hex2mem
*
* Description:
* Read the Intel HEX ASCII data provided on the file descriptor 'fd' and
* write the binary to memory.
*
* If, for example, fd is zero (corresponding to stdin), then the HEX
* ASCII data would be taken from the console and written to memory.
*
* Input Parameters:
* fd - The file descriptor from which Intel HEX data will be
* received.
* baseaddr - The base address of the memory region stream.
* endpaddr - The end address (plus 1) of the memory region.
* swap - Controls byte ordering. See enum hex2bin_swap_e for
* description of the values.
*
* Returned Value:
* Zero (OK) is returned on success; a negated errno value is returned on
* failure.
*
****************************************************************************/
int hex2mem(int fd, unsigned long baseaddr, unsigned long endpaddr,
enum hex2bin_swap_e swap);
/****************************************************************************
* Name: fhex2mem
*
* Description:
* Read the Intel HEX ASCII data provided on the standard stream
* 'instream' and write the binary to memory.
*
* If, for example, instream is stdin, then the HEX ASCII data would be
* taken from the console and written to memory.
*
* Input Parameters:
* instream - The incoming standard stream from which Intel HEX data
* will be received.
* baseaddr - The base address of the memory region stream.
* endpaddr - The end address (plus 1) of the memory region.
* swap - Controls byte ordering. See enum hex2bin_swap_e for
* description of the values.
*
* Returned Value:
* Zero (OK) is returned on success; a negated errno value is returned on
* failure.
*
****************************************************************************/
int fhex2mem(FAR FILE *instream, unsigned long baseaddr,
unsigned long endpaddr, enum hex2bin_swap_e swap);
#undef EXTERN
#ifdef __cplusplus
}
#endif
#endif /* CONFIG_SYSTEM_HEX2BIN */
#endif /* __INCLUDE_HEX2BIN_H */