nuttx/boards/arm/stm32/stm32f103-minimum/include/board.h

198 lines
7.2 KiB
C
Raw Normal View History

/****************************************************************************
* boards/arm/stm32/stm32f103-minimum/include/board.h
*
* Copyright (C) 2016 Gregory Nutt. All rights reserved.
* Authors: Gregory Nutt <gnutt@nuttx.org>
* Laurent Latil <laurent@latil.nom.fr>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#ifndef __BOARDS_ARM_STM32_STM32F103_MINIMUM_INCLUDE_BOARD_H
#define __BOARDS_ARM_STM32_STM32F103_MINIMUM_INCLUDE_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Clocking *************************************************************************/
/* On-board crystal frequency is 8MHz (HSE) */
#define STM32_BOARD_XTAL 8000000ul
/* PLL source is HSE/1, PLL multiplier is 9: PLL frequency is 8MHz (XTAL) x 9 = 72MHz */
#define STM32_CFGR_PLLSRC RCC_CFGR_PLLSRC
#define STM32_CFGR_PLLXTPRE 0
#define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx9
#define STM32_PLL_FREQUENCY (9*STM32_BOARD_XTAL)
/* Use the PLL and set the SYSCLK source to be the PLL */
#define STM32_SYSCLK_SW RCC_CFGR_SW_PLL
#define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL
#define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY
/* AHB clock (HCLK) is SYSCLK (72MHz) */
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK
#define STM32_HCLK_FREQUENCY STM32_PLL_FREQUENCY
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */
/* APB2 clock (PCLK2) is HCLK (72MHz) */
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK
#define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY
/* APB2 timers 1 and 8 will receive PCLK2. */
#define STM32_APB2_TIM1_CLKIN (STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM8_CLKIN (STM32_PCLK2_FREQUENCY)
/* APB1 clock (PCLK1) is HCLK/2 (36MHz) */
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2)
2016-06-09 16:29:55 +02:00
/* APB1 timers 2-7 will be twice PCLK1 */
#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY)
2016-06-09 16:29:55 +02:00
#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY)
/* USB divider -- Divide PLL clock by 1.5 */
#define STM32_CFGR_USBPRE 0
/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
* otherwise frequency is 2xAPBx.
* Note: TIM1,8 are on APB2, others on APB1 */
#define BOARD_TIM1_FREQUENCY STM32_HCLK_FREQUENCY
#define BOARD_TIM2_FREQUENCY STM32_PCLK1_FREQUENCY
#define BOARD_TIM3_FREQUENCY STM32_PCLK1_FREQUENCY
#define BOARD_TIM4_FREQUENCY STM32_PCLK1_FREQUENCY
#define BOARD_TIM5_FREQUENCY STM32_PCLK1_FREQUENCY
#define BOARD_TIM6_FREQUENCY STM32_PCLK1_FREQUENCY
#define BOARD_TIM7_FREQUENCY STM32_PCLK1_FREQUENCY
#define BOARD_TIM8_FREQUENCY STM32_HCLK_FREQUENCY
/* SDIO dividers. Note that slower clocking is required when DMA is disabled
* in order to avoid RX overrun/TX underrun errors due to delayed responses
* to service FIFOs in interrupt driven mode. These values have not been
* tuned!!!
*
* HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz
*/
#define SDIO_INIT_CLKDIV (178 << SDIO_CLKCR_CLKDIV_SHIFT)
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
*/
#ifdef CONFIG_SDIO_DMA
# define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
# define SDIO_MMCXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
#endif
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
*/
#ifdef CONFIG_SDIO_DMA
# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
# define SDIO_SDXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
#endif
2016-10-11 22:14:06 +02:00
/* BUTTON definitions ***************************************************************/
#define NUM_BUTTONS 2
#define BUTTON_USER1 0
#define BUTTON_USER2 1
#define BUTTON_USER1_BIT (1 << BUTTON_USER1)
#define BUTTON_USER2_BIT (1 << BUTTON_USER2)
/* LED definitions ******************************************************************/
/* Define how many LEDs this board has (needed by userleds) */
#define BOARD_NLEDS 1
/* The board has only one controllable LED */
#define LED_STARTED 0 /* No LEDs */
#define LED_HEAPALLOCATE 1 /* LED1 on */
#define LED_IRQSENABLED 2 /* LED2 on */
#define LED_STACKCREATED 3 /* LED1 on */
#define LED_INIRQ 4 /* LED1 off */
#define LED_SIGNAL 5 /* LED2 on */
#define LED_ASSERTION 6 /* LED1 + LED2 */
#define LED_PANIC 7 /* LED1 / LED2 blinking */
/* PWM
*
* The STM32F103-Minimum has no real on-board PWM devices, but the board can
* be configured to output a pulse train using TIM3 CH3 on PB0.
*
* Note: we don't need redefine GPIO_TIM3_CH3OUT because PB0 is not remap pin.
*/
/* RGB LED
*
* R = TIM1 CH1 on PA8 | G = TIM2 CH2 on PA1 | B = TIM4 CH4 on PB9
*
Merged in alinjerpelea/nuttx (pull request #963) Move boards to boards folder * boards: rename configs folder to boards This is the proposed layout after the change: boards: - folder containing board folders <board>: - name of each board drivers: - extra drivers specific for platform include: - header files for the boars scripts: - extra scripts specific for platform src: - board specific code tools: - extra tools specific for platform <config>: - board specific configuration(s) Note: <xxx> names are dependent on platform This is a logical change to aim to the arch layout but this is a huge change it should be done in several steps to lower the risk. Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> * Kconfig: replace configs with boards The change is needed after the path change Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> * Makefile: replace configs with boards The change is needed after the path change Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> * Makefile.*: replace configs with boards The change is needed after the path change Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> * Make.defs: replace configs with boards The change is needed after the path change Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> * .sh: replace configs with boards The change is needed after the path change Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> * .mk: replace configs with boards The change is needed after the path change Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> * .c & .h: replace configs with boards The change is needed after the path change Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> * .bat: replace configs with boards The change is needed after the path change Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com> Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-08-05 14:04:14 +02:00
* Note: Pin boards: GPIO_TIM1_CH1OUT ; GPIO_TIM2_CH2OUT ; GPIO_TIM4_CH4OUT
*/
#define RGBLED_RPWMTIMER 1
#define RGBLED_RPWMCHANNEL 1
#define RGBLED_GPWMTIMER 2
#define RGBLED_GPWMCHANNEL 2
#define RGBLED_BPWMTIMER 4
#define RGBLED_BPWMCHANNEL 4
#endif /* __BOARDS_ARM_STM32_STM32F103_MINIMUM_INCLUDE_BOARD_H */