nuttx/configs/stm32ldiscovery/src/stm32ldiscovery.h

150 lines
6.4 KiB
C
Raw Normal View History

/****************************************************************************************************
* configs/stm32ldiscovery/src/stm32ldiscover.h
* arch/arm/src/board/stm32ldiscover.n
*
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************************************/
#ifndef __CONFIGS_STM32F3DISCOVERY_SRC_STM32F3DISCOVERY_INTERNAL_H
#define __CONFIGS_STM32F3DISCOVERY_SRC_STM32F3DISCOVERY_INTERNAL_H
/****************************************************************************************************
* Included Files
****************************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
/****************************************************************************************************
* Definitions
****************************************************************************************************/
/* Configuration ************************************************************************************/
/* How many SPI modules does this chip support? */
#if STM32_NSPI < 1
# undef CONFIG_STM32_SPI1
# undef CONFIG_STM32_SPI2
# undef CONFIG_STM32_SPI3
#elif STM32_NSPI < 2
# undef CONFIG_STM32_SPI2
# undef CONFIG_STM32_SPI3
#elif STM32_NSPI < 3
# undef CONFIG_STM32_SPI3
#endif
/* STM32L-Discovery GPIOs ***************************************************************************/
/* The STM32L-Discovery board has four LEDs. Two of these are controlled by
* logic on the board and are not available for software control:
*
* LD1 COM: LD2 default status is red. LD2 turns to green to indicate that
* communications are in progress between the PC and the ST-LINK/V2.
* LD2 PWR: Red LED indicates that the board is powered.
*
* And two LEDs can be controlled by software:
*
* User LD3: Green LED is a user LED connected to the I/O PB7 of the STM32L152
* MCU.
* User LD4: Blue LED is a user LED connected to the I/O PB6 of the STM32L152
* MCU.
*
*/
#define GPIO_LED1 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN7)
#define GPIO_LED2 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN6)
/* Button definitions *******************************************************************************/
/* The STM32L-Discovery supports two buttons; only one button is controllable by
* software:
*
* B1 USER: user and wake-up button connected to the I/O PA0 of the STM32F303VCT6.
* B2 RESET: pushbutton connected to NRST is used to RESET the STM32F303VCT6.
*
* NOTE that EXTI interrupts are configured
*/
#define MIN_IRQBUTTON BUTTON_USER
#define MAX_IRQBUTTON BUTTON_USER
#define NUM_IRQBUTTONS 1
#define GPIO_BTN_USER (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTA|GPIO_PIN0)
/* SPI - There is a ST MEMS L3GD20 device on SPI1 using these pins: */
#define GPIO_MEMS_CS (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3)
#define GPIO_MEMS_INT1 (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTE|GPIO_PIN0)
#define GPIO_MEMS_INT2 (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTE|GPIO_PIN1)
/****************************************************************************************************
* Public Types
****************************************************************************************************/
/****************************************************************************************************
* Public data
****************************************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************************************
* Public Functions
****************************************************************************************************/
/****************************************************************************************************
* Name: stm32_spiinitialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the stm32ldiscovery board.
*
****************************************************************************************************/
void weak_function stm32_spiinitialize(void);
/****************************************************************************************************
* Name: stm32_usbinitialize
*
* Description:
* Called from stm32_usbinitialize very early in inialization to setup USB-related
* GPIO pins for the STM32L-Discovery board.
*
****************************************************************************************************/
#ifdef CONFIG_STM32_USB
void weak_function stm32_usbinitialize(void);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_STM32F3DISCOVERY_SRC_STM32F3DISCOVERY_INTERNAL_H */