nuttx/arch/arm/src/sam3u/sam3u_vectors.S

/************************************************************************************************
 * arch/arm/src/sam3u/sam3u_vectors.S
 * arch/arm/src/chip/sam3u_vectors.S
 *
 *   Copyright (C) 2009-2010 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <spudmonkey@racsa.co.cr>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ************************************************************************************************/

/************************************************************************************************
 * Included Files
 ************************************************************************************************/

#include <nuttx/config.h>
#include <arch/irq.h>

/************************************************************************************************
 * Preprocessor Definitions
 ************************************************************************************************/

/* Memory Map:
 *
 * 0x0800:0000 - Beginning of FLASH. Address of vectors.  Mapped to address 0x0000:0000 at boot
 *               time.
 * 0x0803:ffff - End of flash
 * 0x2000:0000 - Start of SRAM and start of .data (_sdata)
 *             - End of .data (_edata) and start of .bss (_sbss)
 *             - End of .bss (_ebss) and bottom of idle stack
 *             - _ebss + CONFIG_IDLETHREAD_STACKSIZE = end of idle stack, start of heap. NOTE
 *               that the ARM uses a decrement before store stack so that the correct initial
 *               value is the end of the stack + 4;
 * 0x2000:bfff - End of SRAM and end of heap
 */

#define IDLE_STACK		(_ebss+CONFIG_IDLETHREAD_STACKSIZE)
#define HEAP_BASE		(_ebss+CONFIG_IDLETHREAD_STACKSIZE)

/* The Cortex-M3 return from interrupt is unusual.  We provide the following special
 * address to the BX instruction.  The particular value also forces a return to
 * thread mode and covers state from the main stack point, the MSP (vs. the MSP).
 */

#define EXC_RETURN		0xfffffff9

/************************************************************************************************
 * Global Symbols
 ************************************************************************************************/

	.globl		__start

	.syntax		unified
	.thumb
	.file		"sam3u_vectors.S"

/************************************************************************************************
 * Macros
 ************************************************************************************************/

/* On entry into an IRQ, the hardware automatically saves the xPSR, PC, LR, R12, R0-R3
 * registers on the stack, then branches to an instantantiation of the following
 * macro.  This macro simply loads the IRQ number into R0, then jumps to the common
 * IRQ handling logic.
 */

	.macro	HANDLER, label, irqno
	.thumb_func
\label:
	mov		r0, #\irqno
	b		sam3u_common
	.endm

/************************************************************************************************
 * Vectors
 ************************************************************************************************/

	.section	.vectors, "ax"
	.code		16
	.align		2
	.globl		sam3u_vectors
	.type		sam3u_vectors, function

sam3u_vectors:

/* Processor Exceptions */

	.word	IDLE_STACK			/* Vector  0: Reset stack pointer */
	.word	__start				/* Vector  1: Reset vector */
	.word	sam3u_nmi			/* Vector  2: Non-Maskable Interrupt (NMI) */
	.word	sam3u_hardfault		/* Vector  3: Hard fault */
	.word	sam3u_mpu			/* Vector  4: Memory management (MPU) */
	.word	sam3u_busfault		/* Vector  5: Bus fault */
	.word	sam3u_usagefault	/* Vector  6: Usage fault */
	.word	sam3u_reserved		/* Vector  7: Reserved */
	.word	sam3u_reserved		/* Vector  8: Reserved */
	.word	sam3u_reserved		/* Vector  9: Reserved */
	.word	sam3u_reserved		/* Vector 10: Reserved */
	.word	sam3u_svcall		/* Vector 11: SVC call */
	.word	sam3u_dbgmonitor	/* Vector 12: Debug monitor */
	.word	sam3u_reserved		/* Vector 13: Reserved */
	.word	sam3u_pendsv		/* Vector 14: Pendable system service request */
	.word	sam3u_systick		/* Vector 15: System tick */

/* External Interrupts */

	.word	sam3u_supc			/* Vector 16+0:  Supply Controller */
	.word	sam3u_rstc			/* Vector 16+1:  Reset Controller */
	.word	sam3u_rtc			/* Vector 16+2:  Real Time Clock */
	.word	sam3u_rtt			/* Vector 16+3:  Real Time Timer */
	.word	sam3u_wdt			/* Vector 16+4:  Watchdog Timer */
	.word	sam3u_pmc			/* Vector 16+5:  Power Management Controller */
	.word	sam3u_eefc0			/* Vector 16+6:  Enhanced Embedded Flash Controller 0 */
	.word	sam3u_eefc1			/* Vector 16+7:  Enhanced Embedded Flash Controller 1 */
	.word	sam3u_uart			/* Vector 16+8:  Universal Asynchronous Receiver Transmitter */
	.word	sam3u_smc			/* Vector 16+9:  Static Memory Controller */
	.word	sam3u_pioa			/* Vector 16+10: Parallel I/O Controller A */
	.word	sam3u_piob			/* Vector 16+11: Parallel I/O Controller B */
	.word	sam3u_pioc			/* Vector 16+12: Parallel I/O Controller C */
	.word	sam3u_usart0		/* Vector 16+13: USART 0 */
	.word	sam3u_usart1		/* Vector 16+14: USART 1 */
	.word	sam3u_usart2		/* Vector 16+15: USART 2 */
	.word	sam3u_usart3		/* Vector 16+16: USART 3 */
	.word	sam3u_hsmci			/* Vector 16+17: High Speed Multimedia Card Interface */
	.word	sam3u_twi0			/* Vector 16+18: Two-Wire Interface 0 */
	.word	sam3u_twi1			/* Vector 16+19: Two-Wire Interface 1 */
	.word	sam3u_spi			/* Vector 16+20: Serial Peripheral Interface */
	.word	sam3u_ssc			/* Vector 16+21: Synchronous Serial Controller */
	.word	sam3u_tc0			/* Vector 16+22: Timer Counter 0 */
	.word	sam3u_tc1			/* Vector 16+23: Timer Counter 1 */
	.word	sam3u_tc2			/* Vector 16+24: Timer Counter 2 */
	.word	sam3u_pwm			/* Vector 16+25: Pulse Width Modulation Controller */
	.word	sam3u_adc12b		/* Vector 16+26: 12-bit ADC Controller */
	.word	sam3u_adc			/* Vector 16+27: 10-bit ADC Controller */
	.word	sam3u_dmac			/* Vector 16+28: DMA Controller */
	.word	sam3u_udphs			/* Vector 16+29: USB Device High Speed */
	.size	sam3u_vectors, .-sam3u_vectors

/************************************************************************************************
 * .text
 ************************************************************************************************/

	.text
	.type	handlers, function
	.thumb_func
handlers:
	HANDLER	sam3u_reserved, SAM3U_IRQ_RESERVED		/* Unexpected/reserved vector */
	HANDLER	sam3u_nmi, SAM3U_IRQ_NMI				/* Vector  2: Non-Maskable Interrupt (NMI) */
	HANDLER	sam3u_hardfault, SAM3U_IRQ_HARDFAULT	/* Vector  3: Hard fault */
	HANDLER	sam3u_mpu, SAM3U_IRQ_MEMFAULT			/* Vector  4: Memory management (MPU) */
	HANDLER	sam3u_busfault, SAM3U_IRQ_BUSFAULT		/* Vector  5: Bus fault */
	HANDLER	sam3u_usagefault, SAM3U_IRQ_USAGEFAULT	/* Vector  6: Usage fault */
	HANDLER	sam3u_svcall, SAM3U_IRQ_SVCALL			/* Vector 11: SVC call */
	HANDLER	sam3u_dbgmonitor, SAM3U_IRQ_DBGMONITOR	/* Vector 12: Debug Monitor */
	HANDLER	sam3u_pendsv, SAM3U_IRQ_PENDSV			/* Vector 14: Penable system service request */
	HANDLER	sam3u_systick, SAM3U_IRQ_SYSTICK		/* Vector 15: System tick */

	HANDLER	sam3u_supc, SAM3U_IRQ_SUPC				/* Vector 16+0:  Supply Controller */
	HANDLER	sam3u_rstc, SAM3U_IRQ_RSTC				/* Vector 16+1:  Reset Controller */
	HANDLER	sam3u_rtc, SAM3U_IRQ_RTC				/* Vector 16+2:  Real Time Clock */
	HANDLER	sam3u_rtt, SAM3U_IRQ_RTT				/* Vector 16+3:  Real Time Timer */
	HANDLER	sam3u_wdt, SAM3U_IRQ_WDT				/* Vector 16+4:  Watchdog Timer */
	HANDLER	sam3u_pmc, SAM3U_IRQ_PMC				/* Vector 16+5:  Power Management Controller */
	HANDLER	sam3u_eefc0, SAM3U_IRQ_EEFC0			/* Vector 16+6:  Enhanced Embedded Flash Controller 0 */
	HANDLER	sam3u_eefc1, SAM3U_IRQ_EEFC1			/* Vector 16+7:  Enhanced Embedded Flash Controller 1 */
	HANDLER	sam3u_uart, SAM3U_IRQ_UART				/* Vector 16+8:  Universal Asynchronous Receiver Transmitter */
	HANDLER	sam3u_smc, SAM3U_IRQ_SMC				/* Vector 16+9:  Static Memory Controller */
	HANDLER	sam3u_pioa, SAM3U_IRQ_PIOA				/* Vector 16+10: Parallel I/O Controller A */
	HANDLER	sam3u_piob, SAM3U_IRQ_PIOB				/* Vector 16+11: Parallel I/O Controller B */
	HANDLER	sam3u_pioc, SAM3U_IRQ_PIOC				/* Vector 16+12: Parallel I/O Controller C */
	HANDLER	sam3u_usart0, SAM3U_IRQ_USART0			/* Vector 16+13: USART 0 */
	HANDLER	sam3u_usart1, SAM3U_IRQ_USART1			/* Vector 16+14: USART 1 */
	HANDLER	sam3u_usart2, SAM3U_IRQ_USART2			/* Vector 16+15: USART 2 */
	HANDLER	sam3u_usart3, SAM3U_IRQ_USART3			/* Vector 16+16: USART 3 */
	HANDLER	sam3u_hsmci, SAM3U_IRQ_HSMCI			/* Vector 16+17: High Speed Multimedia Card Interface */
	HANDLER	sam3u_twi0, SAM3U_IRQ_TWI0				/* Vector 16+18: Two-Wire Interface 0 */
	HANDLER	sam3u_twi1, SAM3U_IRQ_TWI1				/* Vector 16+19: Two-Wire Interface 1 */
	HANDLER	sam3u_spi, SAM3U_IRQ_SPI				/* Vector 16+20: Serial Peripheral Interface */
	HANDLER	sam3u_ssc, SAM3U_IRQ_SSC				/* Vector 16+21: Synchronous Serial Controller */
	HANDLER	sam3u_tc0, SAM3U_IRQ_TC0				/* Vector 16+22: Timer Counter 0 */
	HANDLER	sam3u_tc1, SAM3U_IRQ_TC1				/* Vector 16+23: Timer Counter 1 */
	HANDLER	sam3u_tc2, SAM3U_IRQ_TC2				/* Vector 16+24: Timer Counter 2 */
	HANDLER	sam3u_pwm, SAM3U_IRQ_PWM				/* Vector 16+25: Pulse Width Modulation Controller */
	HANDLER	sam3u_adc12b, SAM3U_IRQ_ADC12B			/* Vector 16+26: 12-bit ADC Controller */
	HANDLER	sam3u_adc, SAM3U_IRQ_ADC				/* Vector 16+27: 10-bit ADC Controller */
	HANDLER	sam3u_dmac, SAM3U_IRQ_DMAC				/* Vector 16+28: DMA Controller */
	HANDLER	sam3u_udphs, SAM3U_IRQ_UDPHS			/* Vector 16+29: USB Device High Speed */

/* Common IRQ handling logic.  On entry here, the return stack is on either
 * the PSP or the MSP and looks like the following:
 *
 *      REG_XPSR
 *      REG_R15
 *      REG_R14
 *      REG_R12
 *      REG_R3
 *      REG_R2
 *      REG_R1
 * MSP->REG_R0
 *
 * And
 *      R0 contains the IRQ number
 *      R14 Contains the EXC_RETURN value
 *      We are in handler mode and the current SP is the MSP
 */

sam3u_common:

	/* Complete the context save */

#ifdef CONFIG_NUTTX_KERNEL
	/* The EXC_RETURN value will be 0xfffffff9 (privileged thread) or 0xfffffff1
	 * (handler mode) if the state is on the MSP.  It can only be on the PSP if
	 * EXC_RETURN is 0xfffffffd (unprivileged thread)
	 */

	adds	r2, r14, #3				/* If R14=0xfffffffd, then r2 == 0 */
	ite		ne						/* Next two instructions are condition */
	mrsne	r1, msp					/* R1=The main stack pointer */
	mrseq	r1, psp					/* R1=The process stack pointer */
#else
	mrs		r1, msp					/* R1=The main stack pointer */
#endif

	mov		r2, r1					/* R2=Copy of the main/process stack pointer */
	add		r2, #HW_XCPT_SIZE		/* R2=MSP/PSP before the interrupt was taken */
	mrs		r3, primask				/* R3=Current PRIMASK setting */
#ifdef CONFIG_NUTTX_KERNEL
	stmdb	r1!, {r2-r11,r14}		/* Save the remaining registers plus the SP value */
#else
	stmdb	r1!, {r2-r11}			/* Save the remaining registers plus the SP value */
#endif

	/* Disable interrupts, select the stack to use for interrupt handling
	 * and call up_doirq to handle the interrupt
	 */

	cpsid	i						/* Disable further interrupts */

	/* If CONFIG_ARCH_INTERRUPTSTACK is defined, we will use a special interrupt
	 * stack pointer.  The way that this is done here prohibits nested interrupts!
	 * Otherwise, we will re-use the main stack for interrupt level processing.
	 */

#if CONFIG_ARCH_INTERRUPTSTACK > 3
	ldr		sp, =g_intstackbase
	str		r1, [sp, #-4]!			/* Save the MSP on the interrupt stack */
	bl		up_doirq				/* R0=IRQ, R1=register save (msp) */
	ldr		r1, [sp, #+4]!			/* Recover R1=main stack pointer */
#else
	mov		sp, r1					/* We are using the main stack pointer */
	bl		up_doirq				/* R0=IRQ, R1=register save (msp) */
	mov		r1, sp					/* Recover R1=main stack pointer */
#endif

	/* On return from up_doirq, R0 will hold a pointer to register context
	 * array to use for the interrupt return.  If that return value is the same
	 * as current stack pointer, then things are relatively easy.
	 */

	cmp		r0, r1					/* Context switch? */
	beq		1f						/* Branch if no context switch */

	/* We are returning with a pending context switch.  This case is different
	 * because in this case, the register save structure does not lie on the
	 * stack but, rather, are within a TCB structure.  We'll have to copy some
	 * values to the stack.
	 */

	add	r1, r0, #SW_XCPT_SIZE		/* R1=Address of HW save area in reg array */
	ldmia	r1, {r4-r11}			/* Fetch eight registers in HW save area */
	ldr	r1, [r0, #(4*REG_SP)]		/* R1=Value of SP before interrupt */
	stmdb	r1!, {r4-r11}			/* Store eight registers in HW save area */
#ifdef CONFIG_NUTTX_KERNEL 
	ldmia	r0, {r2-r11,r14}		/* Recover R4-R11, r14 + 2 temp values */
#else
	ldmia	r0, {r2-r11}			/* Recover R4-R11 + 2 temp values */
#endif
	b		2f						/* Re-join common logic */

	/* We are returning with no context switch.  We simply need to "unwind"
	 * the same stack frame that we created
	 */
1:
#ifdef CONFIG_NUTTX_KERNEL 
	ldmia	r1!, {r2-r11,r14}		/* Recover R4-R11, r14 + 2 temp values */
#else
	ldmia	r1!, {r2-r11}			/* Recover R4-R11 + 2 temp values */
#endif
2:
#ifdef CONFIG_NUTTX_KERNEL
	/* The EXC_RETURN value will be 0xfffffff9 (privileged thread) or 0xfffffff1
	 * (handler mode) if the state is on the MSP.  It can only be on the PSP if
	 * EXC_RETURN is 0xfffffffd (unprivileged thread)
	 */

	adds	r0, r14, #3				/* If R14=0xfffffffd, then r0 == 0 */
	ite		ne						/* Next two instructions are condition */
	msrne	msp, r1					/* R1=The main stack pointer */
	msreq	psp, r1					/* R1=The process stack pointer */
#else
	msr		msp, r1					/* Recover the return MSP value */

	/* Preload r14 with the special return value first (so that the return
	 * actually occurs with interrupts still disabled).
	 */

	ldr		r14, =EXC_RETURN		/* Load the special value */
#endif

    /* Restore the interrupt state */

	msr		primask, r3				/* Restore interrupts */

	/* Always return with R14 containing the special value that will: (1)
	 * return to thread mode, and (2) continue to use the MSP
	 */

	bx		r14						/* And return */
	.size	handlers, .-handlers

/************************************************************************************************
 *  Name: up_interruptstack/g_intstackbase
 *
 * Description:
 *   Shouldn't happen
 *
 ************************************************************************************************/

#if CONFIG_ARCH_INTERRUPTSTACK > 3
	.bss
	.global	g_intstackbase
	.align	4
up_interruptstack:
	.skip	(CONFIG_ARCH_INTERRUPTSTACK & ~3)
g_intstackbase:
	.size	up_interruptstack, .-up_interruptstack
#endif

/************************************************************************************************
 * .rodata
 ************************************************************************************************/

	.section	.rodata, "a"

/* Variables: _sbss is the start of the BSS region (see ld.script) _ebss is the end
 * of the BSS regsion (see ld.script). The idle task stack starts at the end of BSS
 * and is of size CONFIG_IDLETHREAD_STACKSIZE.  The IDLE thread is the thread that
 * the system boots on and, eventually, becomes the idle, do nothing task that runs
 * only when there is nothing else to run.  The heap continues from there until the
 * end of memory.  See g_heapbase below.
 */

	.globl	g_heapbase
	.type	g_heapbase, object
g_heapbase:
	.word	HEAP_BASE
	.size	g_heapbase, .-g_heapbase

	.end