2019-03-10 14:53:57 +01:00
|
|
|
OMNIBUSF4 Target Support README
|
|
|
|
|
===============================
|
|
|
|
|
|
|
|
|
|
"OmnibusF4" is not a product name per se, but rather a design spec
|
|
|
|
|
that many product vendors within the drone flight management unit
|
|
|
|
|
(FMU) community adhere to. The spec defines the major components, and
|
|
|
|
|
how those components are wired into the STM32F405RGT6 microcontroller.
|
|
|
|
|
|
|
|
|
|
Airbot is one such vendor, and they publish a schematic here:
|
|
|
|
|
|
|
|
|
|
http://bit.ly/obf4pro
|
|
|
|
|
|
|
|
|
|
Other software that supports the OmnibusF4 family include Betaflight,
|
2019-03-10 22:23:58 +01:00
|
|
|
iNAV, and many others. PX4 recently added support as well. No code
|
|
|
|
|
from any of those sources is included in this port.
|
2019-03-10 14:53:57 +01:00
|
|
|
|
|
|
|
|
Since OmnibusF4 is a drone FMU, most of its IO is already allocated to
|
|
|
|
|
FMU-specific tasks. As such, we don't need to make the board support
|
|
|
|
|
package as flexible as, say, an STM32F4 Discovery board.
|
|
|
|
|
|
|
|
|
|
The following are some of the committed IO pins. Most of the pins not
|
|
|
|
|
mentioned here are inaccessible, the details vary by board vendor:
|
|
|
|
|
|
|
|
|
|
io peripheral signal notes
|
|
|
|
|
==================================
|
|
|
|
|
XIN 8MHz crystal oscillator
|
|
|
|
|
|
|
|
|
|
PB0 TIM3 CH3 S1_OUT motor 1 PWM output
|
|
|
|
|
PB1 TIM3 CH4 S2_OUT motor 2 PWM output
|
|
|
|
|
PA3 TIM2 CH4 S3_OUT motor 3 PWM output
|
|
|
|
|
PA2 TIM2 CH3 S4_OUT motor 4 PWM output
|
|
|
|
|
PA1 TIM2 CH2 S5_OUT motor 5 PWM output
|
|
|
|
|
PA8 TIM1 CH4 S6_OUT motor 6 PWM output
|
|
|
|
|
|
|
|
|
|
PA4 SPI1 SPI1_NSS mpu6000
|
|
|
|
|
PA5 SPI1 SPI1_SCL
|
|
|
|
|
PA6 SPI1 SPI1_MISO
|
|
|
|
|
PA7 SPI1 SPI1_MOSI
|
|
|
|
|
|
|
|
|
|
PC4 GPIO GYRO_INT mpu6000 EXTI
|
|
|
|
|
|
|
|
|
|
PB10 UART3/I2C UART3_TX ttl UART tx or i2c_scl (used as console)
|
|
|
|
|
PB11 UART3/I2C UART3_RX ttl UART rx or i2c_sda (used as console)
|
|
|
|
|
|
|
|
|
|
PB9 RC_CH2 (rx pwm input)
|
|
|
|
|
PB8 RC_CH1 (rx pwm input)
|
|
|
|
|
PC9 RC_CH6 (rx pwm input)
|
|
|
|
|
PC8 RC_CH5 (rx pwm input)
|
|
|
|
|
PC7 RC_CH4 or USART6_RX (ttl)
|
|
|
|
|
PC6 RC_CH3 or USART6_TX (ttl)
|
|
|
|
|
|
|
|
|
|
PB7 GPIO SD_DET SD card detection pin (low when card inserted)
|
|
|
|
|
PB5 GPIO STAT LED output (active low)
|
|
|
|
|
PB4 GPIO BUZZER buzzer output (active low)
|
|
|
|
|
|
|
|
|
|
PD2 GPIO LED_STRIP one-wire interface for LED strips
|
|
|
|
|
|
|
|
|
|
PC12 SPI3 SPI3_MOSI bmp280 barometer (if populated) and/or max7456 OSD
|
|
|
|
|
PC11 SPI3 SPI3_MISO
|
|
|
|
|
PC10 SPI3 SPI3_SCL
|
|
|
|
|
PA15 GPIO SPI3_NSS OSD NSS
|
|
|
|
|
PB3 GPIO BARO_CS bmp280 NSS (if populated)
|
|
|
|
|
|
|
|
|
|
PA12 OTG USB_DP
|
|
|
|
|
PA11 OTG USB_DN
|
|
|
|
|
|
|
|
|
|
PA10 UART1 USART1_RX SBUS_IN (through inverter) or PPM
|
|
|
|
|
PA9 UART1 USART1_TX
|
|
|
|
|
|
|
|
|
|
PB15 SPI2 SPI2_MOSI sd/mmc card interface
|
|
|
|
|
PB14 SPI2 SPI2_MISO
|
|
|
|
|
PB13 SPI2 SPI2_SCLK
|
|
|
|
|
PB12 SPI2 SPI2_NSS
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Build Instructions
|
|
|
|
|
==================
|
|
|
|
|
|
2019-08-19 17:16:08 +02:00
|
|
|
The boards/arm/stm32/omnibusf4/nsh/defconfig file creates a basic setup, and
|
2019-03-10 14:53:57 +01:00
|
|
|
includes drivers for all supported onboard chips. The console and
|
|
|
|
|
command prompt are sent to USART3.
|
|
|
|
|
|
