nuttx/boards/arm/stm32/olimex-stm32-p207/src/stm32_buttons.c

/****************************************************************************
 * boards/olimex-stm32-p207/src/stm32_buttons.c
 *
 *   Copyright (C) 2011-2012, 2015, 2017 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ****************************************************************************/

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>

#include <stdint.h>
#include <errno.h>

#include <nuttx/arch.h>
#include <nuttx/board.h>
#include <arch/board/board.h>

#include "olimex-stm32-p207.h"

#ifdef CONFIG_ARCH_BUTTONS

/****************************************************************************
 * Private Data
 ****************************************************************************/

/* Pin configuration for each STM32F4 Discovery button.  This array is indexed by
 * the BUTTON_* definitions in board.h
 */

static const uint32_t g_buttons[NUM_BUTTONS] =
{
  GPIO_BTN_TAMPER,
  GPIO_BTN_WKUP,
  GPIO_BTN_RIGHT,
  GPIO_BTN_UP,
  GPIO_BTN_LEFT,
  GPIO_BTN_DOWN,
  GPIO_BTN_CENTER
};

/****************************************************************************
 * Public Functions
 ****************************************************************************/

/****************************************************************************
 * Name: board_button_initialize
 *
 * Description:
 *   board_button_initialize() must be called to initialize button resources.  After
 *   that, board_buttons() may be called to collect the current state of all
 *   buttons or board_button_irq() may be called to register button interrupt
 *   handlers.
 *
 ****************************************************************************/

void board_button_initialize(void)
{
  int i;

  /* Configure the GPIO pins as inputs.  NOTE that EXTI interrupts are
   * configured for all pins.
   */

  for (i = 0; i < NUM_BUTTONS; i++)
    {
      stm32_configgpio(g_buttons[i]);
    }
}

/****************************************************************************
 * Name: board_buttons
 ****************************************************************************/

uint32_t board_buttons(void)
{
  uint32_t ret = 0;

  /* Check that state of each key */

  if (!stm32_gpioread(g_buttons[BUTTON_TAMPER]))
    {
      ret |= BUTTON_TAMPER_BIT;
    }

  if (stm32_gpioread(g_buttons[BUTTON_WKUP]))
    {
      ret |= BUTTON_WKUP_BIT;
    }

  if (stm32_gpioread(g_buttons[BUTTON_RIGHT]))
    {
      ret |= BUTTON_RIGHT_BIT;
    }

  if (stm32_gpioread(g_buttons[BUTTON_UP]))
    {
      ret |= BUTTON_UP_BIT;
    }

  if (stm32_gpioread(g_buttons[BUTTON_LEFT]))
    {
      ret |= BUTTON_LEFT_BIT;
    }

  if (stm32_gpioread(g_buttons[BUTTON_DOWN]))
    {
      ret |= BUTTON_DOWN_BIT;
    }

  if (stm32_gpioread(g_buttons[BUTTON_CENTER]))
    {
      ret |= BUTTON_CENTER_BIT;
    }

  return ret;
}

/************************************************************************************
 * Button support.
 *
 * Description:
 *   board_button_initialize() must be called to initialize button resources.  After
 *   that, board_buttons() may be called to collect the current state of all
 *   buttons or board_button_irq() may be called to register button interrupt
 *   handlers.
 *
 *   After board_button_initialize() has been called, board_buttons() may be called to
 *   collect the state of all buttons.  board_buttons() returns an 32-bit bit set
 *   with each bit associated with a button.  See the BUTTON_*_BIT
 *   definitions in board.h for the meaning of each bit.
 *
 *   board_button_irq() may be called to register an interrupt handler that will
 *   be called when a button is depressed or released.  The ID value is a
 *   button enumeration value that uniquely identifies a button resource. See the
 *   BUTTON_* definitions in board.h for the meaning of enumeration
 *   value.
 *
 ************************************************************************************/

#ifdef CONFIG_ARCH_IRQBUTTONS
int board_button_irq(int id, xcpt_t irqhandler, FAR void *arg)
{
  int ret = -EINVAL;

  /* The following should be atomic */

  if (id >= MIN_IRQBUTTON && id <= MAX_IRQBUTTON)
    {
      ret = stm32_gpiosetevent(g_buttons[id], true, true, true, irqhandler, arg);
    }

  return ret;
}
#endif
#endif /* CONFIG_ARCH_BUTTONS */