2008-03-15 21:00:23 +01:00
|
|
|
README.txt
|
|
|
|
|
^^^^^^^^^^
|
|
|
|
|
|
|
|
|
|
ZDS-II Compiler Versions
|
|
|
|
|
^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
|
|
2009-02-26 04:56:35 +01:00
|
|
|
Different configurations have been build for this board using ZDS-11
|
|
|
|
|
Versions 4.11.0 and 4.11.1. You have to check the files */Make.defs
|
|
|
|
|
to see how the build is configured: Check the definitions of
|
|
|
|
|
ZDSVERSION (if present) and ZDSINSTALLDIR.
|
|
|
|
|
|
|
|
|
|
NOTE: Different versions of the ZDS-II compiler may also require
|
|
|
|
|
different versions of .linkcmd and .zdsproj files as well.
|
|
|
|
|
|
|
|
|
|
Version 4.11.0
|
|
|
|
|
|
|
|
|
|
Although it compiles without error, the 4.11.0 compiler generates
|
2008-03-15 21:00:23 +01:00
|
|
|
This is the only version that this code has been built against.
|
2008-03-25 00:54:58 +01:00
|
|
|
|
|
|
|
|
Although it compiles without error, the 4.11.0 compiler generates
|
|
|
|
|
bad code on one of the files, mm/mm_initialize.c. Below is a simple work-
|
|
|
|
|
around.
|
|
|
|
|
|
|
|
|
|
--- mm/mm_initialize.c.SAVE 2008-02-13 08:06:46.833857700 -0600
|
|
|
|
|
+++ mm/mm_initialize.c 2008-02-13 08:07:26.367608900 -0600
|
|
|
|
|
@@ -94,8 +94,11 @@
|
|
|
|
|
{
|
|
|
|
|
int i;
|
|
|
|
|
|
|
|
|
|
+#if 0 /* DO NOT CHECK IN */
|
|
|
|
|
CHECK_ALLOCNODE_SIZE;
|
|
|
|
|
CHECK_FREENODE_SIZE;
|
|
|
|
|
+#endif
|
|
|
|
|
|
|
|
|
|
/* Set up global variables */
|
2008-03-15 21:00:23 +01:00
|
|
|
|
|
|
|
|
Other Versions
|
|
|
|
|
If you use any version of ZDS-II other than 4.11.0 or if you install ZDS-II
|
|
|
|
|
at any location other than the default location, you will have to modify
|
|
|
|
|
two files: (1) configs/ez80f910200kitg/*/setenv.sh and (2)
|
|
|
|
|
configs/ez80f910200kitg/*/Make.defs.
|
|
|
|
|
|
|
|
|
|
Configuration Subdirectories
|
|
|
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
|
|
|
|
|
|
- src/ and include/
|
|
|
|
|
These directories contain common logic for all ez80f910200kitg
|
|
|
|
|
configurations.
|
|
|
|
|
|
|
|
|
|
Variations on the basic ez80f910200kitg configuration are maintained
|
|
|
|
|
in subdirectories. To configure any specific configuration, do the
|
|
|
|
|
following steps:
|
|
|
|
|
|
|
|
|
|
cd <nuttx-top-directory>/tools
|
|
|
|
|
./configure.sh ez80f910200kitg/<sub-directory>
|
|
|
|
|
cd <nuttx-top-directgory>
|
|
|
|
|
make
|
|
|
|
|
|
|
|
|
|
Where <sub-directory> is the specific board configuration that you
|
|
|
|
|
wish to build. The following board-specific configurations are
|
|
|
|
|
available:
|
|
|
|
|
|
|
|
|
|
- ostest
|
|
|
|
|
This builds the examples/ostest application for execution from FLASH.
|
|
|
|
|
See examples/README.txt for information about ostest.
|
|
|
|
|
|
|
|
|
|
Check out any README.txt files in these <sub-directory>s.
|
