131 lines
4.1 KiB
Plaintext
131 lines
4.1 KiB
Plaintext
|
README
|
||
|
|
======
|
||
|
|
|
||
|
|
This directory contains the port of NuttX to the Pimoroni Tiny 2040.
|
||
|
|
See https://shop.pimoroni.com/products/tiny-2040?variant=39560012234835
|
||
|
|
for information about Pimoroni Tiny 2040.
|
||
|
|
|
||
|
|
The Pimoroni Tiny 2040 has two buttons (RESET and BOOT) allowing to boot
|
||
|
|
from ROM without disconnecting the device.
|
||
|
|
|
||
|
|
Currently only the following devices are supported.
|
||
|
|
|
||
|
|
Supported:
|
||
|
|
- UART (console port)
|
||
|
|
- GPIO 0 (UART0 TX) and GPIO 1 (UART0 RX) are used for the console.
|
||
|
|
- I2C (not tested on Tiny 2040)
|
||
|
|
- SPI
|
||
|
|
- DMAC
|
||
|
|
- USB device
|
||
|
|
- MSC, CDC/ACM serial and these composite device are supported.
|
||
|
|
- CDC/ACM serial device can be used for the console.
|
||
|
|
- PIO (RP2040 Programmable I/O)
|
||
|
|
- Flash ROM Boot
|
||
|
|
- SRAM Boot
|
||
|
|
- If Pico SDK is available, nuttx.uf2 file which can be used in
|
||
|
|
BOOTSEL mode will be created.
|
||
|
|
|
||
|
|
Not supported:
|
||
|
|
- All other devices
|
||
|
|
|
||
|
|
Installation
|
||
|
|
============
|
||
|
|
|
||
|
|
1. Download Raspberry Pi Pico SDK
|
||
|
|
|
||
|
|
$ git clone -b 1.1.2 https://github.com/raspberrypi/pico-sdk.git
|
||
|
|
|
||
|
|
2. Set PICO_SDK_PATH environment variable
|
||
|
|
|
||
|
|
$ export PICO_SDK_PATH=<absolute_path_to_pico-sdk_directory>
|
||
|
|
|
||
|
|
3. Configure and build NuttX
|
||
|
|
|
||
|
|
$ git clone https://github.com/apache/incubator-nuttx.git nuttx
|
||
|
|
$ git clone https://github.com/apache/incubator-nuttx-apps.git apps
|
||
|
|
$ cd nuttx
|
||
|
|
$ make distclean
|
||
|
|
$ ./tools/configure.sh pimoroni-tiny2040:nsh
|
||
|
|
$ make V=1
|
||
|
|
|
||
|
|
4. Connect Pimoroni Tiny 2040 board to USB port. While pressing the
|
||
|
|
BOOT button, shortly press the RESET button. On releasing the BOOT
|
||
|
|
button the board boots from internal ROM and will be detected as
|
||
|
|
USB Mass Storage Device. Then copy "nuttx.uf2" into the device.
|
||
|
|
(Same manner as the standard Pico SDK applications installation.)
|
||
|
|
|
||
|
|
5. To access the console, GPIO 0 and 1 pins must be connected to the
|
||
|
|
device such as USB-serial converter.
|
||
|
|
|
||
|
|
`usbnsh` configuration provides the console access by USB CDC/ACM serial
|
||
|
|
devcice. The console is available by using a terminal software on the USB
|
||
|
|
host.
|
||
|
|
|
||
|
|
Defconfigs
|
||
|
|
==========
|
||
|
|
|
||
|
|
- nsh
|
||
|
|
Minimum configuration with NuttShell
|
||
|
|
|
||
|
|
- nshsram
|
||
|
|
Load NuttX binary to SRAM
|
||
|
|
|
||
|
|
- smp
|
||
|
|
Enable SMP mode. Both Core 0 and Core 1 are used by NuttX.
|
||
|
|
|
||
|
|
- spisd
|
||
|
|
SD card support (SPI connection)
|
||
|
|
Connection:
|
||
|
|
SD card slot ----- Pimoroni Tiny 2040
|
||
|
|
(Pin 9) DAT2 (NC)
|
||
|
|
(Pin 1) DAT3/CS ----- GP5 (SPI0 CSn) (Pin 11)
|
||
|
|
(Pin 2) CMD /DI ----- GP7 (SPI0 TX) (Pin 9)
|
||
|
|
(Pin 3) VSS ----- GND (Pin 2 or 8)
|
||
|
|
(Pin 4) VDD ----- 3V3 OUT (Pin 3)
|
||
|
|
(Pin 5) CLK/SCK ----- GP6 (SPI0 SCK) (Pin 10)
|
||
|
|
(Pin 6) VSS ----- GND (Pin 2 or 8)
|
||
|
|
(Pin 7) DAT0/DO ----- GP4 (SPI0 RX) (Pin 12)
|
||
|
|
(Pin 8) DAT1 (NC)
|
||
|
|
* Card hot swapping is not supported.
|
||
|
|
|
||
|
|
- usbnsh
|
||
|
|
USB CDC/ACM serial console with NuttShell
|
||
|
|
|
||
|
|
- usbmsc
|
||
|
|
USB MSC and CDC/ACM support
|
||
|
|
`msconn` and `sercon` commands enable the MSC and CDC/ACM devices.
|
||
|
|
The MSC support provides the interface to the SD card with SPI,
|
||
|
|
so the SD card slot connection like spisd configuration is required.
|
||
|
|
|
||
|
|
- composite
|
||
|
|
USB composite device (MSC + CDC/ACM) support
|
||
|
|
`conn` command enables the composite device.
|
||
|
|
|
||
|
|
- gpio
|
||
|
|
GPIO driver and example application 'gpio' based on nsh configuration.
|
||
|
|
Following GPIO are configured in include/board.h:
|
||
|
|
GPIO18 (out): onboard RGB LED (red)
|
||
|
|
GPIO19 (out): onboard RGB LED (green)
|
||
|
|
GPIO20 (out): onboard RGB LED (blue)
|
||
|
|
GPIO23 (in) : onboard BOOT (USER) button
|
||
|
|
* No interrupt pin configured.
|
||
|
|
|
||
|
|
License exceptions
|
||
|
|
==================
|
||
|
|
|
||
|
|
The following files are originated from the files in Pico SDK.
|
||
|
|
So, the files are licensed under 3-Clause BSD same as Pico SDK.
|
||
|
|
|
||
|
|
- arch/arm/src/rp2040/rp2040_clock.c
|
||
|
|
- arch/arm/src/rp2040/rp2040_pll.c
|
||
|
|
- arch/arm/src/rp2040/rp2040_xosc.c
|
||
|
|
- These are created by referring the Pico SDK clock initialization.
|
||
|
|
|
||
|
|
- arch/arm/src/rp2040/rp2040_pio.c
|
||
|
|
- arch/arm/src/rp2040/rp2040_pio.h
|
||
|
|
- arch/arm/src/rp2040/rp2040_pio_instructions.h
|
||
|
|
- These provide the similar APIs to Pico SDK's hardware_pio APIs.
|
||
|
|
|
||
|
|
- arch/arm/src/rp2040/hardware/*.h
|
||
|
|
- These are generated from rp2040.svd originally provided in Pico SDK.
|