nuttx/configs/twr-k64f120m/include/board.h

/************************************************************************************
 * configs/twr-k64f120m/include/board.h
 *
 *   Copyright (C) 2017 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ************************************************************************************/

#ifndef __CONFIGS_TWR_K64F120M_INCLUDE_BOARCH_H
#define __CONFIGS_TWR_K64F120M_INCLUDE_BOARCH_H

/************************************************************************************
 * Included Files
 ************************************************************************************/

#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif

/************************************************************************************
 * Pre-processor Definitions
 ************************************************************************************/

/* Clocking *************************************************************************/
/* The K64 tower board uses a 50MHz external clock */

#define BOARD_EXTCLOCK       1              /* External clock */
#define BOARD_EXTAL_FREQ     50000000       /* 50MHz Oscillator */
#define BOARD_XTAL32_FREQ    32768          /* 32KHz RTC Oscillator */

/* PLL Configuration.  Either the external clock or crystal frequency is used to
 * select the PRDIV value. Only reference clock frequencies are supported that will
 * produce a range 2MHz-4MHz reference clock to the PLL.
 *
 *   PLL Input frequency:   PLLIN  = REFCLK/PRDIV = 50MHz/20 = 2.5 MHz
 *   PLL Output frequency:  PLLOUT = PLLIN*VDIV   = 2.5Mhz*48 = 120MHz
 *   MCG Frequency:         PLLOUT = 120 Mhz
 */

#define BOARD_PRDIV          20             /* PLL External Reference Divider */
#define BOARD_VDIV           48             /* PLL VCO Divider (frequency multiplier) */

#define BOARD_PLLIN_FREQ     (BOARD_EXTAL_FREQ / BOARD_PRDIV)
#define BOARD_PLLOUT_FREQ    (BOARD_PLLIN_FREQ * BOARD_VDIV)
#define BOARD_MCG_FREQ       BOARD_PLLOUT_FREQ

/* Define additional MCG_C2 Setting */

#define BOARD_MCG_C2_FCFTRIM 0              /* Do not enable FCFTRIM */
#define BOARD_MCG_C2_LOCRE0  MCG_C2_LOCRE0  /* Enable reset on loss of clock */

/* SIM CLKDIV1 dividers */

#define BOARD_OUTDIV1        1              /* Core        = MCG, 120MHz */
#define BOARD_OUTDIV2        2              /* Bus         = MCG/2, 60MHz */
#define BOARD_OUTDIV3        2              /* FlexBus     = MCG/2, 60MHz */
#define BOARD_OUTDIV4        5              /* Flash clock = MCG/5, 24MHz */

#define BOARD_CORECLK_FREQ  (BOARD_MCG_FREQ / BOARD_OUTDIV1)
#define BOARD_BUS_FREQ      (BOARD_MCG_FREQ / BOARD_OUTDIV2)
#define BOARD_FLEXBUS_FREQ  (BOARD_MCG_FREQ / BOARD_OUTDIV3)
#define BOARD_FLASHCLK_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV4)

/* SDHC clocking ********************************************************************/

/* SDCLK configurations corresponding to various modes of operation.   Formula is:
 *
 *   SDCLK  frequency = (base clock) / (prescaler * divisor)
 *
 * The SDHC module is always configure configured so that the core clock is the base
 * clock.
 */

/* Identification mode:  375KHz = 120MHz / ( 64 * 5) <= 400 KHz */

#define BOARD_SDHC_IDMODE_PRESCALER    SDHC_SYSCTL_SDCLKFS_DIV64
#define BOARD_SDHC_IDMODE_DIVISOR      SDHC_SYSCTL_DVS_DIV(5)

/* MMC normal mode: 15MHz  = 120MHz / (8 * 1) <= 16 MHz*/

#define BOARD_SDHC_MMCMODE_PRESCALER   SDHC_SYSCTL_SDCLKFS_DIV8
#define BOARD_SDHC_MMCMODE_DIVISOR     SDHC_SYSCTL_DVS_DIV(1)

/* SD normal mode (1-bit): 15MHz  = 120MHz / (8 * 1) <= 16 MHz*/

#define BOARD_SDHC_SD1MODE_PRESCALER   SDHC_SYSCTL_SDCLKFS_DIV8
#define BOARD_SDHC_SD1MODE_DIVISOR     SDHC_SYSCTL_DVS_DIV(1)

/* SD normal mode (4-bit): 20MHz  = 120MHz / (2 * 3) (with DMA) <= 24MHz
 * SD normal mode (4-bit): 15MHz  = 120MHz / (8 * 1) (no DMA) <= 16MHz
 */

#ifdef CONFIG_SDIO_DMA
#  define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
#  define BOARD_SDHC_SD4MODE_DIVISOR   SDHC_SYSCTL_DVS_DIV(3)
#else
#  define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV8
#  define BOARD_SDHC_SD4MODE_DIVISOR   SDHC_SYSCTL_DVS_DIV(1)
#endif


/* LED definitions ******************************************************************/
/* The TWR-K64F120M has four LEDs:
 *
 * 1. D5 / Green LED    PTE6 
 * 2. D6 / Yellow LED   PTE7 
 * 3. D7 / Orange LED   PTE8 
 * 4  D9 / Blue LED     PTE9 
 *
 * LED4 is reservered for user.
 * The 3 first LEDs are encoded as follows:
 */

#define LED_STARTED       0  /* N/A */
#define LED_HEAPALLOCATE  1  /* N/A */
#define LED_IRQSENABLED   2  /* N/A */
#define LED_STACKCREATED  3  /* LED1 - OS is started */
#define LED_INIRQ         4  /* LED2 */
#define LED_SIGNAL        5  /* LED3 */
#define LED_ASSERTION     6  /* LED1 + LED2 + LED3 */
#define LED_PANIC         7  /* LED1 (blink) */


/* Open SDA serial link */

#define PIN_UART1_RX  PIN_UART1_RX_1
#define PIN_UART1_TX  PIN_UART1_TX_1


/* Ethernet */

#ifdef CONFIG_KINETIS_ENET
#  define CONFIG_KINETIS_NENET 1
#endif

/************************************************************************************
 * Public Data
 ************************************************************************************/

#ifndef __ASSEMBLY__

#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif

/************************************************************************************
 * Public Function Prototypes
 ************************************************************************************/
/************************************************************************************
 * Name: kinetis_boardinitialize
 *
 * Description:
 *   All STM32 architectures must provide the following entry point.  This entry point
 *   is called early in the intitialization -- after all memory has been configured
 *   and mapped but before any devices have been initialized.
 *
 ************************************************************************************/

void kinetis_boardinitialize(void);

#undef EXTERN
#if defined(__cplusplus)
}
#endif

#endif /* __ASSEMBLY__ */
#endif  /* __CONFIGS_TWR_K64F120M_INCLUDE_BOARCH_H */