sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
61f6915898
nuttx/configs/nucleo-144/README.txt

307 lines
11 KiB
Plaintext
Raw Normal View History

README.txt file for the nucleo-144
2016-05-12 17:56:32 +02:00
README
======
This README discusses issues unique to NuttX configurations for the ST
Nucleo F746ZG board from ST Micro. See
http://www.st.com/web/catalog/tools/FM116/CL1620/SC959/SS1532/LN1847/PF261636
The Nucleo F746ZG order part number is NUCLEO-F746ZG. It is clumped together
under the STM32 Nucleo-144 board family. This does provide uniformity in the
documentation from ST and should allow us to quickly change configurations
but just cloning this configuration and changing the CPU choice and board
init. Unfortunately for the developer, the CPU specific information must be
extracted from the common information in the documentation.
Please read the User Manaul UM1727: Getting started with STM32 Nucleo board
software development tools and take note of the Powering options for the
board (6.3 Power supply and power selection) and the Solder bridges based
hardware configuration changes that are configurable (6.11 Solder bridges).
NUCLEO-F746ZG:
Microprocessor: STM32F746ZGT6 Core: ARM 32-bit Cortex®-M7 CPU with FPU,
L1-cache: 4KB data cache and 4KB instruction cache, up to
216 MHz, MPU, and DSP instructions.
Memory: 1024 KB Flash 320KB of SRAM (including 64KB of data TCM RAM)
+ 16KB of instruction TCM RAM + 4KB of backup SRAM
ADC: 3×12-bit, 2.4 MSPS ADC: up to 24 channels and 7.2 MSPS in
triple interleaved mode
DMA: 16-stream DMA controllers with FIFOs and burst support
Timers: Up to 18 timers: up to thirteen 16-bit (1x 16-bit lowpower),
two 32-bit timers, 2x watchdogs, SysTick
GPIO: 114 I/O ports with interrupt capability
LCD: LCD-TFT Controllerwith (DMA2D), Parallel interface
I2C: 4 × I2C interfaces (SMBus/PMBus)
U[S]ARTs: 4 USARTs, 4 UARTs (27 Mbit/s, ISO7816 interface, LIN, IrDA,
modem control)
SPI/12Ss: 6/3 (simplex) (up to 50 Mbit/s), 3 with muxed simplex I2S
for audio class accuracy via internal audio PLL or external
clock
QSPI: Dual mode Quad-SPI
SAIs: 2 Serial Audio Interfaces
CAN: 2 X CAN interface
SDMMC interface
SPDIFRX interface
USB: USB 2.0 full-speed device/host/OTG controller with on-chip
PHY
10/100 Ethernet: MAC with dedicated DMA: supports IEEE 1588v2 hardware,
MII/RMII
Camera Interface: 8/14 Bit
CRC calculation unit
TRG: True random number generator
RTC
Board features:
Peripherals: 8 leds, 2 push button (3 LEDs, 1 button) under software
control
Debug: STLINK/V2-1 debugger/programmer Uses a STM32F103CB to
provide a ST-Link for programming, debug similar to the
OpenOcd FTDI function - USB to JTAG front-end.
Expansion I/F ST Zio an Extended Ardino and Morpho Headers
See https://developer.mbed.org/platforms/ST-Nucleo-F746ZG form additional information about this board.
Contents
========
- Development Environment
- IDEs
- Basic configuaration & build steps
- Hardware
- Button
- LED
- U[S]ARTs and Serial Consoles
- Configurations
Development Environment
=======================
Either Linux or Cygwin on Windows can be used for the development environment.
The source has been built only using the GNU toolchain (see below). Other
toolchains will likely cause problems.
All testing has been conducted using the GNU toolchain from ARM for Linux.
found here https://launchpad.net/gcc-arm-embedded/4.9/4.9-2015-q3-update/+download/gcc-arm-none-eabi-4_9-2015q3-20150921-linux.tar.bz2
If you change the default toolchain, then you may also have to modify the PATH in
the setenv.h file if your make cannot find the tools.
IDEs
====
NuttX is built using command-line make. It can be used with an IDE, but some
effort will be required to create the project.
Makefile Build
--------------
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
simply use the NuttX makefile to build the system. That is almost for free
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
there is a lot of help on the internet).
Basic configuration & build steps
==================================
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
be modified to point to the correct path to the Cortex-M7 GCC toolchain (if
different from the default in your PATH variable).
- Configures nuttx creating .config file in the nuttx directory
$ cd tools && ./configure.sh nucleo-f746zg/nsh && cd ..
- Refreshes the .config file with the latest features addes sice this writting
$ make oldconfig
- Select the features you want in the build.
$ make menuconfig
- Builds Nuttx with the features you selected.
$ make
Hardware
========
GPIO - there are 144 I/O lines on the STM32F746ZGT6 with various pins pined out
on the Nucleo F746ZG
See https://developer.mbed.org/platforms/ST-Nucleo-F746ZG/ for slick graphic
pinouts.
Keep in mind that:
1) The I/O is 3.3 Volt not 5 Volt like on the Arduino products.
2) The Nucleo-144 board family has 3 pages of Solder Bridges AKA Solder
Blobs (SB) that can alter the factory configuration. We will note SB
in effect but will assume the facitory defualt settings.
Our main concern is establishing a console and LED utilization for
debugging. Because so many pins can be multiplexed with so many functions,
the above mentioned graphic is super helpful in indentifying a serial port
that will not rob us of another IO feature. Namely Serial Port 8 (UART8)
with TX on PE1 and RX on PE0. Of course if your design has used those
pins you can choose another IO configuration to bring out Serial Port 8
or choose a completely different U[S]ART to use as the console.
In that Case, You will need to edit the include/board.h to select different
U[S]ART and / or pin selections.
Serial
----
SERIAL_RX PE_0
SERIAL_TX PE_1
Buttons
-------
B1 USER: the user button is connected to the I/O PC13 (Tamper support, SB173
ON and SB180 OFF)
LEDs
----
The Board provides a 3 user LEDs, LD1-LD3
LED1 (Green) PB_0 (SB120 ON and SB119 OFF)
LED2 (Blue) PB_7 (SB139 ON)
LED3 (Red) PB_14 (SP118 ON)
- When the I/O is HIGH value, the LEDs are on.
- When the I/O is LOW, the LEDs are off.
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
defined. In that case, the usage by the board port is defined in
include/board.h and src/stm32_autoleds.c. The LEDs are used to encode OS
related events as follows when the LEDs are available:
SYMBOL Meaning RED GREEN BLUE
------------------- ----------------------- -----------
LED_STARTED 0 OFF OFF OFF
LED_HEAPALLOCATE 0 OFF OFF OFF
LED_IRQSENABLED 0 OFF OFF OFF
LED_STACKCREATED 1 OFF ON OFF
LED_INIRQ 2 NC NC ON (momentary)
LED_SIGNAL 2 NC NC ON (momentary)
LED_ASSERTION 3 ON NC NC (momentary)
LED_PANIC 4 ON OFF OFF (flashing 2Hz)
OFF - means that the OS is still initializing. Initialization is very fast so
if you see this at all, it probably means that the system is hanging up
somewhere in the initialization phases.
GREEN - This means that the OS completed initialization.
BLUE - Whenever and interrupt or signal handler is entered, the BLUE LED is
illuminated and extinguished when the interrupt or signal handler exits.
RED - If a recovered assertion occurs, the RED LED will be illuminated
briefly while the assertion is handled. You will probably never see this.
Flashing RED - In the event of a fatal crash, all other LEDs will be
extinguished and RED LED will FLASH at a 2Hz rate.
Thus if the GREEN LED is lit, NuttX has successfully booted and is,
apparently, running normally. If the RED LED is flashing at
approximately 2Hz, then a fatal error has been detected and the system has
halted.
Serial Consoles
===============
USART8
------
Pins and Connectors:
GPIO Connector NAME
RXD: PE0 CN11 pin 64, PE0
CN10 pin 33, D34
TXD: PE1 CN11 pin 61, PE1
You must use a 3.3 TTL to RS-232 converter or a USB to 3.3V TTL
Nucleo 144 FTDI TTL-232R-3V3
----------- ------------
TXD - CN11 pin 64 - RXD - Pin 5 (Yellow)
RXD - CN11 pin 61 - TXD - Pin 4 (Orange)
GND CN11 pin 63 GND Pin 1 (Black)
*Note you will be reverse RX/TX
Use make menuconfig to configure USART8 as the console:
CONFIG_STM32F7_UART8=y
CONFIG_USART8_ISUART=y
CONFIG_USART8_SERIAL_CONSOLE=y
CONFIG_UART8_RXBUFSIZE=256
CONFIG_UART8_TXBUFSIZE=256
CONFIG_UART8_BAUD=115200
CONFIG_UART8_BITS=8
CONFIG_UART8_PARITY=0
CONFIG_UART8_2STOP=0
Virtual COM Port
----------------
Yet another option is to use USART3 and the USB virtual COM port. This
option may be more convenient for long term development, but is painful
to use during board bring-up.
Solder Bridges. This configuration requires:
PD8 USART3 TX SB5 ON and SB7 OFF (Default)
PD9 USART3 RX SB6 ON and SB4 OFF (Default)
Configuring USART3 is the same as given above but add the S and #3.
Question: What BAUD should be configure to interface with the Virtual
COM port? 115200 8N1?
Default
-------
As shipped, SB4 and SB7 are open and SB5 and SB6 closed, so the
virtual COM port is enabled.
Configurations
==============
nsh:
---------
Configures the NuttShell (nsh) located at apps/examples/nsh for the
Nucleo-144 boards. The Configuration enables the serial interfaces
on UART8. Support for builtin applications is enabled, but in the base
configuration no builtin applications are selected (see NOTES below).
NOTES:
1. This configuration uses the mconf-based configuration tool. To
change this configuration using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.
b. If this is the intall configuration then Execute
'cd tools && ./configure.sh stm32f746g-disco/nsh && cd ..'
in nuttx/ in order to start configuration process.
Caution: Doing this step more than once will overwrite .config with
the contents of the stm32f746g-disco/nsh/defconfig file.
c. Execute 'make oldconfig' in nuttx/ in order to refresh the
configuration.
d. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
e. Save the .config file to reuse it in the future starting at step d.
2. By default, this configuration uses the ARM GNU toolchain
for Linux. That can easily be reconfigured, of course.
CONFIG_HOST_LINUX=y : Builds under Linux
CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIL=y : ARM GNU for Linux
3. Although the default console is USART3 (which would correspond to
the Virtual COM port) I have done all testing with the console
device configured for UART8 (see instruction above under "Serial
Consoles).
Reference in New Issue Copy Permalink