2023-10-27 12:57:14 +02:00
|
|
|
==================
|
|
|
|
|
Segger RTT drivers
|
|
|
|
|
==================
|
|
|
|
|
|
2023-11-06 14:11:57 +01:00
|
|
|
.. note:: Segger drivers works only with J-Link debug probes.
|
|
|
|
|
Sometimes it's possible to replace vendor-specific debug interface
|
|
|
|
|
with J-Link OB firmware. For details look at
|
|
|
|
|
`Segger website <https://www.segger.com/downloads/jlink>`_
|
|
|
|
|
|
2023-10-27 12:57:14 +02:00
|
|
|
Supported Segger drivers:
|
|
|
|
|
|
2023-11-06 14:11:57 +01:00
|
|
|
* Serial over RTT - ``CONFIG_SERIAL_RTTx``,
|
|
|
|
|
* Console over RTT - ``CONFIG_SERIAL_RTT_CONSOLE_CHANNEL``
|
|
|
|
|
* Segger SystemView - ``CONFIG_SEGGER_SYSVIEW``
|
|
|
|
|
* Note RTT - ``CONFIG_NOTE_RTT``
|
|
|
|
|
|
|
|
|
|
Segger SystemView
|
|
|
|
|
=================
|
|
|
|
|
|
|
|
|
|
Steps to enable SystemView support:
|
|
|
|
|
|
|
|
|
|
#. Make sure your architecture supports a high-performance counter.
|
|
|
|
|
In most cases it will be:
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_ARCH_PERF_EVENTS=y`
|
|
|
|
|
|
|
|
|
|
In that case, the the architecture logic must initialize the perf counter
|
|
|
|
|
with ``up_perf_init()``.
|
|
|
|
|
|
|
|
|
|
#. Enable instrumentation support:
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_SCHED_INSTRUMENTATION=y`
|
|
|
|
|
|
|
|
|
|
#. Configure instrumentation support. Available options for SystemView are:
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_SCHED_INSTRUMENTATION_SWITCH=y`
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_SCHED_INSTRUMENTATION_SYSCALL=y`
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_SCHED_INSTRUMENTATION_IRQHANDLER=y`
|
|
|
|
|
|
|
|
|
|
#. Make sure that ``CONFIG_TASK_NAME_SIZE > 0``, otherwise task/thread
|
|
|
|
|
names will not be displayed correctly
|
|
|
|
|
|
|
|
|
|
#. Enable Note Driver support and disable Note RAM driver:
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_DRIVERS_NOTE=y`
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_DRIVERS_NOTERAM=n`
|
|
|
|
|
|
|
|
|
|
#. Enable Note RTT and Segger SystemView support:
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_NOTE_RTT=y`
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_SEGGER_SYSVIEW=y`
|
|
|
|
|
|
|
|
|
|
#. Configure RTT channel and RTT buffer size for SystemView:
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_SEGGER_SYSVIEW_RTT_CHANNEL=0`
|
|
|
|
|
|
|
|
|
|
:menuselection:`CONFIG_SEGGER_SYSVIEW_RTT_BUFFER_SIZE=1024`
|
|
|
|
|
|
|
|
|
|
In case SystemView returns buffer overflow errors, you should increase
|
|
|
|
|
``CONFIG_NOTE_RTT_BUFFER_SIZE_UP``.
|
