nuttx/boards/arm/nrf52/nrf52-feather/include/board.h

/****************************************************************************
 * boards/arm/nrf52/nrf52_feather/include/board.h
 *
 *   Copyright (C) 2018 Gregory Nutt. All rights reserved.
 *   Author:  Janne Rosberg <janne@offcode.fi>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ****************************************************************************/

#ifndef __BOARDS_ARM_NRF52_NRF52_FEATHER_INCLUDE_BOARD_H
#define __BOARDS_ARM_NRF52_NRF52_FEATHER_INCLUDE_BOARD_H

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>
#include <stdbool.h>

#if defined(CONFIG_ARCH_IRQBUTTONS) && defined(CONFIG_NRF52_GPIOTE)
#  include <nuttx/irq.h>
#endif

/****************************************************************************
 * Pre-processor Definitions
 ****************************************************************************/

/* Clocking ****************************************************************/

#define BOARD_SYSTICK_CLOCK         (64000000)

/* LED definitions *********************************************************/

/* A low output illuminates the LED.
 *
 * LED index values for use with board_userled()
 */

#define BOARD_LED1        0
#define BOARD_LED2        1
#define BOARD_NLEDS       2

/* LED bits for use with board_userled_all() */

#define BOARD_LED1_BIT    (1 << BOARD_LED1)
#define BOARD_LED2_BIT    (1 << BOARD_LED2)

/* If CONFIG_ARCH_LEDS is defined, the LED will be controlled as follows
 * for NuttX debug functionality (where NC means "No Change").
 */

#define LED_STARTED                0  /* OFF      */
#define LED_HEAPALLOCATE           0  /* OFF      */
#define LED_IRQSENABLED            0  /* OFF      */
#define LED_STACKCREATED           1  /* ON       */
#define LED_INIRQ                  2  /* NC       */
#define LED_SIGNAL                 2  /* NC       */
#define LED_ASSERTION              2  /* NC       */
#define LED_PANIC                  3  /* Flashing */

/* If CONFIG_ARCH_LEDS is not defined, then the LEDs are completely under
 * control of the application.  The following interfaces are then available
 * for application control of the LEDs:
 *
 *  uint32_t board_userled_initialize(void);
 *  void board_userled(int led, bool ledon);
 *  void board_userled_all(uint8_t ledset);
 */

/* Button definitions *******************************************************/

/* No buttons on board */

/* UART Pins ****************************************************************/

/* The following definitions must be provided so that the NRF52 serial
 * driver can set up the UART for the serial console properly.
 */

#define BOARD_UART0_RX_PIN  (GPIO_INPUT  | GPIO_PORT0 | GPIO_PIN(8))
#define BOARD_UART0_TX_PIN  (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT0 | GPIO_PIN(6))

#endif /* __BOARDS_ARM_NRF52_NRF52_FEATHER_INCLUDE_BOARD_H */