104 lines
3.1 KiB
ReStructuredText
104 lines
3.1 KiB
ReStructuredText
|
========
|
||
|
|
Commands
|
||
|
|
========
|
||
|
|
|
||
|
|
This page shows ``wapi`` commands, their arguments and outputs. For a
|
||
|
|
complete list of ``wapi`` commands available to the system, just run
|
||
|
|
``wapi``::
|
||
|
|
|
||
|
|
nsh> wapi
|
||
|
|
Usage:
|
||
|
|
wapi show <ifname>
|
||
|
|
wapi scan <ifname>
|
||
|
|
wapi scan_results <ifname>
|
||
|
|
wapi ip <ifname> <IP address>
|
||
|
|
wapi mask <ifname> <mask>
|
||
|
|
wapi freq <ifname> <frequency> <index/flag>
|
||
|
|
wapi essid <ifname> <essid> <index/flag>
|
||
|
|
wapi psk <ifname> <passphrase> <index/flag> <wpa>
|
||
|
|
wapi disconnect <ifname>
|
||
|
|
wapi mode <ifname> <index/mode>
|
||
|
|
wapi ap <ifname> <MAC address>
|
||
|
|
wapi bitrate <ifname> <bitrate> <index/flag>
|
||
|
|
wapi txpower <ifname> <txpower> <index/flag>
|
||
|
|
wapi country <ifname> <country code>
|
||
|
|
wapi sense <ifname>
|
||
|
|
wapi pta_prio <ifname> <index/flag>
|
||
|
|
wapi help
|
||
|
|
|
||
|
|
Frequency Flags:
|
||
|
|
[0] WAPI_FREQ_AUTO
|
||
|
|
[1] WAPI_FREQ_FIXED
|
||
|
|
|
||
|
|
ESSID Flags:
|
||
|
|
[0] WAPI_ESSID_OFF
|
||
|
|
[1] WAPI_ESSID_ON
|
||
|
|
|
||
|
|
Passphrase algorithm Flags:
|
||
|
|
[0] WPA_ALG_NONE
|
||
|
|
[1] WPA_ALG_WEP
|
||
|
|
[2] WPA_ALG_TKIP
|
||
|
|
[3] WPA_ALG_CCMP
|
||
|
|
|
||
|
|
Passphrase WPA version:
|
||
|
|
[0] WPA_VER_NONE
|
||
|
|
[1] WPA_VER_1
|
||
|
|
[2] WPA_VER_2
|
||
|
|
[3] WPA_VER_3
|
||
|
|
|
||
|
|
Operating Modes:
|
||
|
|
[0] WAPI_MODE_AUTO
|
||
|
|
[1] WAPI_MODE_ADHOC
|
||
|
|
[2] WAPI_MODE_MANAGED
|
||
|
|
[3] WAPI_MODE_MASTER
|
||
|
|
[4] WAPI_MODE_REPEAT
|
||
|
|
[5] WAPI_MODE_SECOND
|
||
|
|
[6] WAPI_MODE_MONITOR
|
||
|
|
[7] WAPI_MODE_MESH
|
||
|
|
|
||
|
|
Bitrate Flags:
|
||
|
|
[0] WAPI_BITRATE_AUTO
|
||
|
|
[1] WAPI_BITRATE_FIXED
|
||
|
|
|
||
|
|
TX power Flags:
|
||
|
|
[0] WAPI_TXPOWER_DBM
|
||
|
|
[1] WAPI_TXPOWER_MWATT
|
||
|
|
[2] WAPI_TXPOWER_RELATIVE
|
||
|
|
|
||
|
|
pta prio Flags:
|
||
|
|
[0] WAPI_PTA_PRIORITY_COEX_MAXIMIZED
|
||
|
|
[1] WAPI_PTA_PRIORITY_COEX_HIGH
|
||
|
|
[2] WAPI_PTA_PRIORITY_BALANCED
|
||
|
|
[3] WAPI_PTA_PRIORITY_WLAN_HIGHD
|
||
|
|
[4] WAPI_PTA_PRIORITY_WLAN_MAXIMIZED
|
||
|
|
|
||
|
|
Arguments
|
||
|
|
=========
|
||
|
|
|
||
|
|
Command's arguments are available on ``wapi``'s usage helper.
|
||
|
|
|
||
|
|
.. note:: ``<>`` means a required argument and ``[]`` an optional one.
|
||
|
|
|
||
|
|
A short explanation of them follows:
|
||
|
|
|
||
|
|
``<ifname>``
|
||
|
|
------------
|
||
|
|
|
||
|
|
The interface name is arch-dependent and it's usually set for a specific
|
||
|
|
operating mode. For instance, ``wlan0`` would be an interface used for STA
|
||
|
|
mode and ``wlan1`` for SoftAP.
|
||
|
|
|
||
|
|
Please refer to the :doc:`Supported Platforms </platforms/index>` for
|
||
|
|
platform-specific definitions. As an example, please check
|
||
|
|
:ref:`ESP32 Wi-Fi Station Mode <esp32_wi-fi_sta>` and
|
||
|
|
:ref:`ESP32 Wi-Fi SoftAP Mode <esp32_wi-fi_softap>` Wi-Fi sections.
|
||
|
|
|
||
|
|
``<index/flag>``
|
||
|
|
----------------
|
||
|
|
|
||
|
|
The ``<index/flag>`` can be used as a numerical or textual value. For
|
||
|
|
instance, considering the ``wapi psk`` command, one could use indistinctly::
|
||
|
|
|
||
|
|
nsh> wapi psk wlan0 mypasswd 3
|
||
|
|
nsh> wapi psk wlan0 mypasswd WPA_ALG_CCMP
|