229 lines
6.0 KiB
ReStructuredText
229 lines
6.0 KiB
ReStructuredText
|
===============================
|
|||
|
|
W5500-EVB-Pico
|
|||
|
|
===============================
|
|||
|
|
|
|||
|
|
The `W5500-EVB-Pico <https://docs.wiznet.io/Product/iEthernet/W5500/w5500-evb-pico/>`_
|
|||
|
|
is a microcontroller evaluation board based on the Raspberry Pi RP2040 and fully
|
|||
|
|
hardwired TCP/IP controller W5500 – and basically works the same as Raspberry Pi
|
|||
|
|
Pico board but with additional Ethernet via W5500.
|
|||
|
|
|
|||
|
|
.. figure:: W5500-EVB-Pico.png
|
|||
|
|
:align: center
|
|||
|
|
|
|||
|
|
Features
|
|||
|
|
========
|
|||
|
|
|
|||
|
|
* RP2040 microcontroller chip
|
|||
|
|
* Dual-core ARM Cortex M0+ processor, flexible clock running up to 133 MHz
|
|||
|
|
* 264kB of SRAM, and 2MB of on-board Flash memory
|
|||
|
|
* Castellated module allows soldering direct to carrier boards
|
|||
|
|
* USB 1.1 Host and Device support
|
|||
|
|
* Low-power sleep and dormant modes
|
|||
|
|
* Drag & drop programming using mass storage over USB
|
|||
|
|
* 26 multi-function GPIO pins
|
|||
|
|
* 2× SPI, 2× I2C, 2× UART, 3× 12-bit ADC, 16× controllable PWM channels
|
|||
|
|
* Accurate clock and timer on-chip
|
|||
|
|
* Temperature sensor
|
|||
|
|
* Accelerated floating point libraries on-chip
|
|||
|
|
* 8 × Programmable IO (PIO) state machines for custom peripheral support
|
|||
|
|
* Ethernet port via WIZnet W5500, hardwired to SPI0 and two GPIO pins.
|
|||
|
|
|
|||
|
|
Supported RP2040 capabilities
|
|||
|
|
=============================
|
|||
|
|
|
|||
|
|
* UART (console port)
|
|||
|
|
|
|||
|
|
* GPIO 0 (UART0 TX) and GPIO 1 (UART0 RX) are used for the console.
|
|||
|
|
|
|||
|
|
* I2C
|
|||
|
|
* SPI (master only)
|
|||
|
|
* DMAC
|
|||
|
|
* PWM
|
|||
|
|
* ADC
|
|||
|
|
* Watchdog
|
|||
|
|
* USB device
|
|||
|
|
|
|||
|
|
* MSC, CDC/ACM serial and these composite device are supported.
|
|||
|
|
* CDC/ACM serial device can be used for the console.
|
|||
|
|
|
|||
|
|
* PIO (RP2040 Programmable I/O)
|
|||
|
|
* Flash ROM Boot
|
|||
|
|
* SRAM Boot
|
|||
|
|
|
|||
|
|
* If Pico SDK is available, nuttx.uf2 file which can be used in
|
|||
|
|
BOOTSEL mode will be created.
|
|||
|
|
* Persistent flash filesystem in unused flash ROM
|
|||
|
|
|
|||
|
|
Currently unsupported RP2040 capabilities
|
|||
|
|
=========================================
|
|||
|
|
|
|||
|
|
* SPI Slave Mode
|
|||
|
|
* SSI
|
|||
|
|
* RTC
|
|||
|
|
* Timers
|
|||
|
|
|
|||
|
|
Serial Console
|
|||
|
|
==============
|
|||
|
|
|
|||
|
|
The board is configured to use the USB connection as the serial console.
|
|||
|
|
|
|||
|
|
Buttons and LEDs
|
|||
|
|
================
|
|||
|
|
|
|||
|
|
User LED controlled by GPIO25.
|
|||
|
|
|
|||
|
|
A BOOTSEL button, which if held down when power is first
|
|||
|
|
applied to the board, will cause the RP2040 to boot into programming
|
|||
|
|
mode and appear as a storage device to a computer connected via USB.
|
|||
|
|
Saving a .UF2 file to this device will replace the Flash ROM contents
|
|||
|
|
on the RP2040.
|
|||
|
|
|
|||
|
|
Pin Mapping
|
|||
|
|
===========
|
|||
|
|
Pads numbered anticlockwise from USB connector.
|
|||
|
|
|
|||
|
|
===== ========== ==========
|
|||
|
|
Pad Signal Notes
|
|||
|
|
===== ========== ==========
|
|||
|
|
1 GPIO0 Default TX for UART0 serial console
|
|||
|
|
2 GPIO1 Default RX for UART1 serial console
|
|||
|
|
3 Ground
|
|||
|
|
4 GPIO2
|
|||
|
|
5 GPIO3
|
|||
|
|
6 GPIO4
|
|||
|
|
7 GPIO5
|
|||
|
|
8 Ground
|
|||
|
|
9 GPIO6
|
|||
|
|
10 GPIO7
|
|||
|
|
11 GPIO8
|
|||
|
|
12 GPIO9
|
|||
|
|
13 Ground
|
|||
|
|
14 GPIO10
|
|||
|
|
15 GPIO11
|
|||
|
|
16 GPIO12
|
|||
|
|
17 GPIO13
|
|||
|
|
18 Ground
|
|||
|
|
19 GPIO14
|
|||
|
|
20 GPIO15
|
|||
|
|
21 GPIO16 W5500 MISO
|
|||
|
|
22 GPIO17 W5500 CSn
|
|||
|
|
23 Ground
|
|||
|
|
24 GPIO18 W5500 SCLK
|
|||
|
|
25 GPIO19 W5500 MOSI
|
|||
|
|
26 GPIO20 W5500 RSTn
|
|||
|
|
27 GPIO21 W5500 INTn
|
|||
|
|
28 Ground
|
|||
|
|
29 GPIO22
|
|||
|
|
30 Run
|
|||
|
|
31 GPIO26 ADC0
|
|||
|
|
32 GPIO27 ADC1
|
|||
|
|
33 AGND Analog Ground
|
|||
|
|
34 GPIO28 ADC2
|
|||
|
|
35 ADC_VREF
|
|||
|
|
36 3V3 Power output to peripherals
|
|||
|
|
37 3V3_EN Pull to ground to turn off.
|
|||
|
|
38 Ground
|
|||
|
|
39 VSYS +5V Supply to board
|
|||
|
|
40 VBUS Connected to USB +5V
|
|||
|
|
===== ========== ==========
|
|||
|
|
|
|||
|
|
Other RP2040 Pins
|
|||
|
|
=================
|
|||
|
|
|
|||
|
|
====== ==========
|
|||
|
|
Signal Notes
|
|||
|
|
====== ==========
|
|||
|
|
GPIO23 Output - Power supply control.
|
|||
|
|
GPIO24 Input - High if USB port or Pad 40 supplying power.
|
|||
|
|
GPIO25 Output - On board LED.
|
|||
|
|
ADC3 Input - Analog voltage equal to one third of VSys voltage.
|
|||
|
|
====== ==========
|
|||
|
|
|
|||
|
|
Separate pins for the Serial Debug Port (SDB) are available
|
|||
|
|
|
|||
|
|
Power Supply
|
|||
|
|
============
|
|||
|
|
|
|||
|
|
The W5500-EVB-Pico can be powered via the USB connector,
|
|||
|
|
or by supplying +5V to pin 39. The board had a diode that prevents
|
|||
|
|
power from pin 39 from flowing back to the USB socket, although
|
|||
|
|
the socket can be power via pin 30.
|
|||
|
|
|
|||
|
|
The W5500-EVB-Pico chip run on 3.3 volts. This is supplied
|
|||
|
|
by an onboard voltage regulator. This regulator can be disabled
|
|||
|
|
by pulling pin 37 to ground.
|
|||
|
|
|
|||
|
|
The regulator can run in two modes. By default the regulator runs
|
|||
|
|
in PFM mode which provides the best efficiency, but may be
|
|||
|
|
switched to PWM mode for improved ripple by outputting a one
|
|||
|
|
on GPIO23.
|
|||
|
|
|
|||
|
|
Installation
|
|||
|
|
============
|
|||
|
|
|
|||
|
|
1. Download Raspberry Pi Pico SDK
|
|||
|
|
|
|||
|
|
::
|
|||
|
|
|
|||
|
|
$ git clone -b 1.1.2 https://github.com/raspberrypi/pico-sdk.git
|
|||
|
|
|
|||
|
|
2. Set PICO_SDK_PATH environment variable
|
|||
|
|
|
|||
|
|
::
|
|||
|
|
|
|||
|
|
$ export PICO_SDK_PATH=<absolute_path_to_pico-sdk_directory>
|
|||
|
|
|
|||
|
|
3. Configure and build NuttX
|
|||
|
|
|
|||
|
|
::
|
|||
|
|
|
|||
|
|
$ git clone https://github.com/apache/nuttx.git nuttx
|
|||
|
|
$ git clone https://github.com/apache/nuttx-apps.git apps
|
|||
|
|
$ cd nuttx
|
|||
|
|
$ make distclean
|
|||
|
|
$ ./tools/configure.sh w5500-evb-pico:usbnsh
|
|||
|
|
$ make V=1
|
|||
|
|
|
|||
|
|
4. Connect W5500-EVB-Pico board to USB port while pressing BOOTSEL.
|
|||
|
|
The board will be detected as USB Mass Storage Device.
|
|||
|
|
Then copy "nuttx.uf2" into the device.
|
|||
|
|
(Same manner as the standard Pico SDK applications installation.)
|
|||
|
|
|
|||
|
|
5. `usbnsh` configuration provides the console access by USB CDC/ACM serial
|
|||
|
|
devcice. The console is available by using a terminal software on the USB
|
|||
|
|
host.
|
|||
|
|
|
|||
|
|
Configurations
|
|||
|
|
==============
|
|||
|
|
|
|||
|
|
usbnsh
|
|||
|
|
------
|
|||
|
|
|
|||
|
|
USB CDC/ACM serial console with NuttShell. TCP/IPv4 & IPv6 networking is
|
|||
|
|
supported via the Ethernet port.
|
|||
|
|
|
|||
|
|
License exceptions
|
|||
|
|
==================
|
|||
|
|
|
|||
|
|
The following files are originated from the files in Pico SDK.
|
|||
|
|
So, the files are licensed under 3-Clause BSD same as Pico SDK.
|
|||
|
|
|
|||
|
|
Created by referring to the Pico SDK clock initialization
|
|||
|
|
---------------------------------------------------------
|
|||
|
|
|
|||
|
|
* arch/arm/src/rp2040/rp2040_clock.c
|
|||
|
|
* arch/arm/src/rp2040/rp2040_pll.c
|
|||
|
|
* arch/arm/src/rp2040/rp2040_xosc.c
|
|||
|
|
|
|||
|
|
Providing an API similar to the Pico SDK's hardware_pio API
|
|||
|
|
-----------------------------------------------------------
|
|||
|
|
|
|||
|
|
* arch/arm/src/rp2040/rp2040_pio.c
|
|||
|
|
* arch/arm/src/rp2040/rp2040_pio.h
|
|||
|
|
* arch/arm/src/rp2040/rp2040_pio_instructions.h
|
|||
|
|
|
|||
|
|
Generated from rp2040.svd originally provided in Pico SDK
|
|||
|
|
---------------------------------------------------------
|
|||
|
|
|
|||
|
|
* arch/arm/src/rp2040/hardware/\*.h
|