nuttx/configs/olimex-strp711/src/up_enc28j60.c

196 lines
6.9 KiB
C
Raw Normal View History

/****************************************************************************
* configs/olimex-strp711/src/up_enc28j60.c
*
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/*
* ENC28J60 Module
*
* The ENC28J60 module does not come on the Olimex-STR-P711, but this describes
* how I have connected it:
*
* Module CON5 QFN ENC2860 Description
* --------------- -------------------------------------------------------
* 1 J8-1 NET CS 5 ~CS Chip select input pin for SPI interface (active low)
* 2 2 SCK 4 SCK Clock in pin for SPI interface
* 3 3 MOSI 3 SI Data in pin for SPI interface
* 4 4 MISO 2 SO Data out pin for SPI interface
* 5 5 GND -- --- ---
* 10 J9-1 3V3 -- --- ---
* 9 2 WOL 1 ~WOL Unicast WOL filter
* 8 3 NET INT 28 ~INT Interrupt output pin (active low)
* 7 4 CLKOUT 27 CLKOUT Programmable clock output pin
* 6 5 NET RST 6 ~RESET Active-low device Reset input
*
* For the Olimex STR-P711, the ENC28J60 module is placed on SPI0 and uses
* P0.3 for CS, P1.4 for an interrupt, and P1.5 as a reset:
*
* Module CON5 Olimex STR-P711 Connection
* --------------- -------------------------------------------------------
* 1 J8-1 NET CS SPI0-2 P0.3 output P0.3/S0.SS/I1.SDA
* 2 2 SCK SPI0-5 SCLK0 P0.2/S0.SCLK/I1.SCL
* 3 3 MOSI SPI0-3 MOSI0 P0.0/S0.MOSI/U3.RX
* 4 4 MISO SPI0-4 MISO0 P0.1/S0.MISO/U3.TX
* 5 5 GND SPI0-1 GND
* 10 J9-1 3V3 SPI0-6 3.3V
* 9 2 WOL NC
* 8 3 NET INT TMR1_EXT-5 P1.4 input P1.4/T1.ICAPA/T1.EXTCLK
* 7 4 CLKOUT NC
* 6 5 NET RST TMR1_EXT_4 P1.5 output P1.5/T1.ICAPB
*
* UART3, I2C cannot be used with SPI0. The GPIOs selected for the ENC28J60
* interrupt conflict with TMR1.
*/
#warning "Need to select differnt interrupt pin.. XTI doesn't support this one"
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <stdio.h>
#include <debug.h>
#include <nuttx/spi.h>
#include <nuttx/enc28j60.h>
#include <arch/board/board.h>
#include "chip.h"
#include "up_arch.h"
#include "up_internal.h"
#include "str71x_internal.h"
#ifdef CONFIG_NET_ENC28J60
/****************************************************************************
* Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* We assume that the ENC28J60 is on SPI0 */
#ifndef CONFIG_STR71X_BSPI0
# error "Need CONFIG_STR71X_BSPI0 in the configuration"
#endif
#ifndef CONFIG_STR71X_XTI
# error "Need CONFIG_STR71X_XTI in the configuration"
#endif
/* UART3, I2C cannot be used with SPI0. The GPIOs selected for the ENC28J60
* interrupt conflict with TIM1.
*/
#ifdef CONFIG_STR71X_UART3
# error "CONFIG_STR71X_UART3 cannot be used in this configuration"
#endif
#ifdef CONFIG_STR71X_TIM1
# error "CONFIG_STR71X_TIM1 cannot be used in this configuration"
#endif
/* SPI Assumptions **********************************************************/
#define ENC28J60_SPI_PORTNO 1 /* On SPI1 */
#define ENC28J60_DEVNO 0 /* Only one ENC28J60 */
#define ENC28J60_IRQ STR71X_IRQ_FIRSTXTI /* NEEDED!!!!!!!!!!!!!!!! */
#warning "Eventually need to fix XTI IRQ number!"
/****************************************************************************
* Private Data
****************************************************************************/
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: up_netinitialize
****************************************************************************/
void up_netinitialize(void)
{
FAR struct spi_dev_s *spi;
int ret;
/* Get the SPI port */
nvdbg("Initializing SPI port %d\n", ENC28J60_SPI_PORTNO);
spi = up_spiinitialize(ENC28J60_SPI_PORTNO);
if (!spi)
{
ndbg("Failed to initialize SPI port %d\n",
ENC28J60_SPI_PORTNO);
return;
}
/* Configure the XTI for the ENC28J60 interrupt. */
ret = str71x_xticonfig(ENC28J60_IRQ, false);
if (ret < 0)
{
ndbg("Failed configure interrupt for IRQ %d: %d\n", ENC28J60_IRQ, ret);
return;
}
nvdbg("Successfully initialized SPI port %d\n",
ENC28J60_SPI_PORTNO);
/* Bind the SPI port to the ENC28J60 driver */
nvdbg("Binding SPI port %d to ENC28J60 device %d\n",
ENC28J60_SPI_PORTNO, ENC28J60_DEVNO);
ret = enc_initialize(spi, ENC28J60_DEVNO, ENC28J60_IRQ);
if (ret < 0)
{
ndbg("Failed to bind SPI port %d ENC28J60 device %d: %d\n",
ENC28J60_SPI_PORTNO, ENC28J60_DEVNO, ret);
return;
}
nvdbg("Successfuly bound SPI port %d ENC28J60 device %d\n",
ENC28J60_SPI_PORTNO, ENC28J60_DEVNO);
}
#endif /* CONFIG_NET_ENC28J60 */