nuttx/boards/renesas/m16c/skp16c26/include/board.h

135 lines
6.2 KiB
C
Raw Normal View History

/****************************************************************************
* boards/renesas/m16c/skp16c26/include/board.h
*
* Copyright (C) 2009 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#ifndef __BOARDS_RENESAS_M32262F8_SKP16C26_INCLUDE_BOARD_H
#define __BOARDS_RENESAS_M32262F8_SKP16C26_INCLUDE_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* User configuration checks ************************************************/
/* According to SKP16C26 documention, "SIO/UART1 pins are used for
* communication between the SKP16C26 board kernel and KD30 Debugger through
* the ICD. Do not connect these pins to any other circuit, as UART1 cannot
* be used in the user program.
* For details, please see ICD (RTA-FoUSB-MON) User Manual on Target M16C
* ROM Monitor Resources or related ICD application notes."
*
* However, the schematic appears to show that SIO/UART2 is actual connection.
* To be safe, we will error out on either selection:
*/
#if defined(CONFIG_M16C_UART1) || defined(CONFIG_M16C_UART2)
# error "UART1/2 should not be used on SKP16C26"
#endif
/* Hardware defintitions ****************************************************/
/* Xin Freq */
#define M16C_XIN_FREQ 20000000 /* 20MHz */
/* Interrupt Priority Levels ************************************************/
/* IPL settings */
#define M16C_DEFAULT_IPL 0 /* Default M16C Interrupt priority level */
#undef M16C_INTERRUPT_IPL /* Default interrupt IPL to enabled nested interrupts */
/* Define any of the following to specify interrupt priorities. A default
* value of 5 will be used for any unspecified values
*/
#undef M16C_INT3_PRIO /* INT3 interrupt priority */
#undef M16C_INT5_PRIO /* INT5 interrupt priority */
#undef M16C_INT4_PRIO /* INT4 interrupt priority */
#undef M16C_BCN_PRIO /* Bus collision detection interrupt priority */
#undef M16C_DM0_PRIO /* DMA0 interrupt priority */
#undef M16C_DM1_PRIO /* DMA1 interrupt priority */
#undef M16C_KUP_PRIO /* Key input interrupt priority */
#undef M16C_AD_PRIO /* A-D conversion interrupt priority */
#undef M16C_S2T_PRIO /* UART2 transmit interrupt priority */
#undef M16C_S2R_PRIO /* UART2 receive interrupt priority */
#undef M16C_S0T_PRIO /* UART0 transmit interrupt priority */
#undef M16C_S0R_PRIO /* UART0 receive interrupt priority */
#undef M16C_S1T_PRIO /* UART1 transmit interrupt priority */
#undef M16C_S1R_PRIO /* UART1 receive interrupt priority */
#define M16C_TA0_PRIO 5 /* Timer A0 interrupt priority */
#undef M16C_TA1_PRIO /* Timer A1 interrupt priority */
#undef M16C_TA2_PRIO /* Timer A2 interrupt priority */
#undef M16C_TA3_PRIO /* Timer A3 interrupt priority */
#undef M16C_TA4_PRIO /* Timer A4 interrupt priority */
#undef M16C_TB0_PRIO /* Timer B0 interrupt priority */
#undef M16C_TB1_PRIO /* Timer B1 interrupt priority */
#undef M16C_TB2_PRIO /* Timer B2 interrupt priority */
#undef M16C_INT0_PRIO /* INT0 interrupt priority */
#undef M16C_INT1_PRIO /* INT1 interrupt priority */
/* LED definitions **********************************************************/
/* GREEN YELLOW RED */
#define LED_STARTED 0 /* OFF OFF OFF */
#define LED_HEAPALLOCATE 1 /* ON OFF OFF */
#define LED_IRQSENABLED 2 /* OFF ON OFF */
#define LED_STACKCREATED 3 /* ON ON OFF */
#define LED_INIRQ 4 /* ON OFF ON */
#define LED_SIGNAL 5 /* OFF ON ON */
#define LED_ASSERTION 6 /* ON ON ON */
#define LED_PANIC 7 /* NC** NC** ON* */
/* *=FLASHING **=if INIRQ, SIGNAL, or ASSERTION will be flashing */
/* BUTTON definitions *******************************************************/
#define SW1_PRESSED 0x01 /* Bit 0: 1=SW1 pressed */
#define SW2_PRESSED 0x02 /* Bit 1: 1=SW2 pressed */
#define SW3_PRESSED 0x04 /* Bit 2: 1=SW3 pressed */
/****************************************************************************
* Inline Functions
****************************************************************************/
#ifndef __ASSEMBLY__
#endif
#endif /* __BOARDS_RENESAS_M32262F8_SKP16C26_INCLUDE_BOARD_H */