2022-07-22 03:04:05 +02:00
|
|
|
|
=======================
|
|
|
|
|
|
Adafruit QT Py RP2040
|
|
|
|
|
|
=======================
|
|
|
|
|
|
|
|
|
|
|
|
The QT Py RP2040 is a tiny general purpose RP2040 board supplied by
|
|
|
|
|
|
Adafruit.
|
|
|
|
|
|
|
|
|
|
|
|
.. figure:: QT-Py.png
|
|
|
|
|
|
:align: center
|
|
|
|
|
|
|
|
|
|
|
|
Features
|
|
|
|
|
|
========
|
|
|
|
|
|
|
|
|
|
|
|
* RP2040 microcontroller chip
|
|
|
|
|
|
* Dual-core ARM Cortex M0+ processor, flexible clock running up to 133 MHz
|
|
|
|
|
|
* 264kB of SRAM, and 8MB of on-board Flash memory
|
|
|
|
|
|
* Castellated module allows soldering direct to carrier boards
|
|
|
|
|
|
* USB Host and Device support via type C connector.
|
|
|
|
|
|
* Low-power sleep and dormant modes
|
|
|
|
|
|
* Drag & drop programming using mass storage over USB
|
|
|
|
|
|
* 13 multi-function GPIO pins (11 breakout pads and two QT pads)
|
|
|
|
|
|
* 2× SPI, 2× I2C, 2× UART, 4× 12-bit ADC, 16× controllable PWM channels
|
|
|
|
|
|
* Accurate clock and timer on-chip
|
|
|
|
|
|
* Temperature sensor
|
|
|
|
|
|
* Accelerated floating point libraries on-chip
|
|
|
|
|
|
* 8 × Programmable IO (PIO) state machines for custom peripheral support
|
|
|
|
|
|
|
|
|
|
|
|
Serial Console
|
|
|
|
|
|
==============
|
|
|
|
|
|
|
|
|
|
|
|
By default a serial console appears on GPIO pins 20 (RX GPIO1) and pin 5
|
|
|
|
|
|
(TX GPIO1). This console runs a 115200-8N1.
|
|
|
|
|
|
|
|
|
|
|
|
The board can be configured to use the USB connection as the serial console.
|
|
|
|
|
|
|
|
|
|
|
|
Buttons and LEDs
|
|
|
|
|
|
================
|
|
|
|
|
|
|
|
|
|
|
|
A ws2812 (NeoPixel) smart RGB LED controlled by GPIO12 (data) and
|
|
|
|
|
|
GPIO11 (power).
|
|
|
|
|
|
|
|
|
|
|
|
There is a BOOT button which if held down when power is first
|
|
|
|
|
|
applied or the RESET button is pressed will cause the RP2040 to
|
|
|
|
|
|
boot into program mode and appear as a storage device to
|
|
|
|
|
|
a USB connecter. Saving a .UF2 file to this device will
|
|
|
|
|
|
replace the Flash ROM contents on the RP2040.
|
|
|
|
|
|
|
|
|
|
|
|
A RESET button that allows rebooting the board without disconnecting
|
|
|
|
|
|
the power.
|
|
|
|
|
|
|
|
|
|
|
|
Pin Mapping
|
|
|
|
|
|
===========
|
|
|
|
|
|
Pads numbered anticlockwise from USB connector.
|
|
|
|
|
|
|
|
|
|
|
|
===== ========== ==========
|
|
|
|
|
|
Pad Signal Notes
|
|
|
|
|
|
===== ========== ==========
|
|
|
|
|
|
1 GPIO26 ADC0
|
|
|
|
|
|
2 GPIO27 ADC1
|
|
|
|
|
|
3 GPIO28 ADC2
|
|
|
|
|
|
4 GPIO29 ADC3
|
|
|
|
|
|
5 GPIO24
|
|
|
|
|
|
6 GPIO25
|
|
|
|
|
|
7 GPIO20 Default TX for UART1 serial console
|
|
|
|
|
|
8 GPIO5 Default RX for UART1 serial console
|
|
|
|
|
|
9 GPIO6
|
|
|
|
|
|
10 GPIO4
|
|
|
|
|
|
11 GPIO3
|
|
|
|
|
|
12 3.3V Power out to peripherals.
|
|
|
|
|
|
13 Ground
|
|
|
|
|
|
14 5V
|
|
|
|
|
|
===== ========== ==========
|
|
|
|
|
|
|
|
|
|
|
|
The board has a STEMMA QT connector that is also connected to
|
|
|
|
|
|
pins GPIO22 (I2C1 SDA) and GPIO23 (I2C1 SCL).
|
|
|
|
|
|
|
|
|
|
|
|
Power Supply
|
|
|
|
|
|
============
|
|
|
|
|
|
|
|
|
|
|
|
The Raspberry Pi Pico can be powered via the USB connector,
|
|
|
|
|
|
or by supplying +5V to pin 14. The board had a diode that prevents
|
|
|
|
|
|
power from pin 14 from flowing back to the USB socket, although
|
|
|
|
|
|
this can be disabled by connecting on-board solder pads if there
|
|
|
|
|
|
is need to run as a usb host.
|
|
|
|
|
|
|
|
|
|
|
|
The Raspberry Pi Pico chip run on 3.3 volts which is supplied by
|
|
|
|
|
|
an on board regulator.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Configurations
|
|
|
|
|
|
==============
|
|
|
|
|
|
|
|
|
|
|
|
gpio
|
|
|
|
|
|
--------
|
|
|
|
|
|
|
|
|
|
|
|
NuttShell configuration (console enabled in UART1, at 115200 bps) with GPIO examples.
|
|
|
|
|
|
|
|
|
|
|
|
nsh
|
|
|
|
|
|
---
|
|
|
|
|
|
|
|
|
|
|
|
Basic NuttShell configuration (console enabled in UART1, at 115200 bps).
|
|
|
|
|
|
|
2022-09-05 20:34:58 +02:00
|
|
|
|
nsh-flash
|
|
|
|
|
|
---------
|
|
|
|
|
|
|
|
|
|
|
|
Basic NuttShell configuration (console enabled in UART0, at 115200 bps
|
|
|
|
|
|
with SMART flash filesystem.
|
|
|
|
|
|
|
2022-07-22 03:04:05 +02:00
|
|
|
|
nshsram
|
|
|
|
|
|
-------
|
|
|
|
|
|
|
|
|
|
|
|
NuttShell configuration (console enabled in UART1, at 115200 bps) with interrupt
|
|
|
|
|
|
vectors in RAM.
|
|
|
|
|
|
|
|
|
|
|
|
smp
|
|
|
|
|
|
---
|
|
|
|
|
|
|
|
|
|
|
|
Basic NuttShell configuration (console enabled in UART1, at 115200 bps) with
|
|
|
|
|
|
both ARM cores enabled.
|
|
|
|
|
|
|
|
|
|
|
|
usbnsh
|
|
|
|
|
|
------
|
|
|
|
|
|
|
|
|
|
|
|
Basic NuttShell configuration (console enabled in USB Port, at 115200 bps).
|
|
|
|
|
|
|
2023-10-25 20:28:04 +02:00
|
|
|
|
README.txt
|
|
|
|
|
|
==========
|
|
|
|
|
|
|
|
|
|
|
|
.. include:: README.txt
|
|
|
|
|
|
:literal:
|
