nuttx/tools/esp32c3/Config.mk

############################################################################
# tools/esp32c3/Config.mk
#
# Licensed to the Apache Software Foundation (ASF) under one or more
# contributor license agreements.  See the NOTICE file distributed with
# this work for additional information regarding copyright ownership.  The
# ASF licenses this file to you under the Apache License, Version 2.0 (the
# "License"); you may not use this file except in compliance with the
# License.  You may obtain a copy of the License at
#
#   http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
# License for the specific language governing permissions and limitations
# under the License.
#
############################################################################

# These are the macros that will be used in the NuttX make system to compile
# and assemble source files and to insert the resulting object files into an
# archive.  These replace the default definitions at tools/Config.mk

ifeq ($(CONFIG_ESP32C3_FLASH_2M),y)
	FLASH_SIZE := 2MB
else ifeq ($(CONFIG_ESP32C3_FLASH_4M),y)
	FLASH_SIZE := 4MB
else ifeq ($(CONFIG_ESP32C3_FLASH_8M),y)
	FLASH_SIZE := 8MB
else ifeq ($(CONFIG_ESP32C3_FLASH_16M),y)
	FLASH_SIZE := 16MB
endif

ifeq ($(CONFIG_ESP32C3_FLASH_MODE_DIO),y)
	FLASH_MODE := dio
else ifeq ($(CONFIG_ESP32C3_FLASH_MODE_DOUT),y)
	FLASH_MODE := dout
else ifeq ($(CONFIG_ESP32C3_FLASH_MODE_QIO),y)
	FLASH_MODE := qio
else ifeq ($(CONFIG_ESP32C3_FLASH_MODE_QOUT),y)
	FLASH_MODE := qout
endif

ifeq ($(CONFIG_ESP32C3_FLASH_FREQ_80M),y)
	FLASH_FREQ := 80m
else ifeq ($(CONFIG_ESP32C3_FLASH_FREQ_40M),y)
	FLASH_FREQ := 40m
else ifeq ($(CONFIG_ESP32C3_FLASH_FREQ_26M),y)
	FLASH_FREQ := 26m
else ifeq ($(CONFIG_ESP32C3_FLASH_FREQ_20M),y)
	FLASH_FREQ := 20m
endif

ESPTOOL_FLASH_OPTS := -fs $(FLASH_SIZE) -fm $(FLASH_MODE) -ff $(FLASH_FREQ)
ESPTOOL_ELF2IMG_OPTS := $(ESPTOOL_FLASH_OPTS)

ifeq ($(CONFIG_ESP32C3_FLASH_DETECT),y)
	ESPTOOL_WRITEFLASH_OPTS := -fs detect -fm $(FLASH_MODE) -ff $(FLASH_FREQ)
else
	ESPTOOL_WRITEFLASH_OPTS := $(ESPTOOL_FLASH_OPTS)
endif

ifdef ESPTOOL_BINDIR
	BL_OFFSET := 0x0
	PT_OFFSET := 0x8000
	BOOTLOADER := $(ESPTOOL_BINDIR)/bootloader-esp32c3.bin
	PARTITION_TABLE := $(ESPTOOL_BINDIR)/partition-table-esp32c3.bin
	FLASH_BL := $(BL_OFFSET) $(BOOTLOADER)
	FLASH_PT := $(PT_OFFSET) $(PARTITION_TABLE)
endif

# POSTBUILD -- Perform post build operations

define POSTBUILD
	$(Q) echo "MKIMAGE: ESP32-C3 binary"
	$(Q) if ! esptool.py version 1>/dev/null 2>&1; then \
		echo ""; \
		echo "esptool.py not found.  Please run: \"pip install esptool\""; \
		echo ""; \
		echo "Run make again to create the nuttx.bin image."; \
		exit 1; \
	fi
	$(Q) if [ -z $(FLASH_SIZE) ]; then \
		echo "Missing Flash memory size configuration for the ESP32-C3 chip."; \
		exit 1; \
	fi
	esptool.py -c esp32c3 elf2image $(ESPTOOL_ELF2IMG_OPTS) -o nuttx.bin nuttx
	$(Q) echo "Generated: nuttx.bin (ESP32-C3 compatible)"
endef

# ESPTOOL_BAUD -- Serial port baud rate used when flashing/reading via esptool.py

ESPTOOL_BAUD ?= 921600

# DOWNLOAD -- Download binary image via esptool.py

define DOWNLOAD

	$(eval ESPTOOL_BINS := $(FLASH_BL) $(FLASH_PT) 0x10000 $(1).bin)

	$(Q) if [ -z $(ESPTOOL_PORT) ]; then \
		echo "DOWNLOAD error: Missing serial port device argument."; \
		echo "USAGE: make download ESPTOOL_PORT=<port> [ ESPTOOL_BAUD=<baud> ]"; \
		exit 1; \
	fi
	esptool.py -c esp32c3 -p $(ESPTOOL_PORT) -b $(ESPTOOL_BAUD) write_flash $(ESPTOOL_WRITEFLASH_OPTS) $(ESPTOOL_BINS)
endef