nuttx/configs/stm3240g-eval/include/board.h

/************************************************************************************
 * configs/stm3240g-eval/include/board.h
 * include/arch/board/board.h
 *
 *   Copyright (C) 2009 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ************************************************************************************/

#ifndef __ARCH_BOARD_BOARD_H
#define __ARCH_BOARD_BOARD_H

/************************************************************************************
 * Included Files
 ************************************************************************************/

#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
#include "stm32_rcc.h"
#include "stm32_sdio.h"
#include "stm32_internal.h"

/************************************************************************************
 * Definitions
 ************************************************************************************/

/* Clocking *************************************************************************/
/* Four clock sources are available on STM3240G-EVAL evaluation board for
 * STM32F407IGH6 and RTC embedded:
 *
 * X1, 25 MHz crystal for ethernet PHY with socket. It can be removed when clock is
 *     provided by MCO pin of the MCU
 * X2, 26 MHz crystal for USB OTG HS PHY
 * X3, 32 kHz crystal for embedded RTC
 * X4, 25 MHz crystal with socket for STM32F407IGH6 microcontroller (It can be removed
 *     from socket when internal RC clock is used.)
 *
 * This is the "standard" configuration as set up by arch/arm/src/stm32f40xx_rcc.c:
 *   System Clock source           : PLL (HSE)
 *   SYSCLK(Hz)                    : 168000000    Determined by PLL configuration
 *   HCLK(Hz)                      : 168000000    (STM32_RCC_CFGR_HPRE)
 *   AHB Prescaler                 : 1            (STM32_RCC_CFGR_HPRE)
 *   APB1 Prescaler                : 4            (STM32_RCC_CFGR_PPRE1)
 *   APB2 Prescaler                : 2            (STM32_RCC_CFGR_PPRE2)
 *   HSE Frequency(Hz)             : 25000000     (STM32_BOARD_XTAL)
 *   PLLM                          : 25           (STM32_PLLCFG_PLLM)
 *   PLLN                          : 336          (STM32_PLLCFG_PLLN)
 *   PLLP                          : 2            (STM32_PLLCFG_PLLP)
 *   PLLQ                          : 7            (STM32_PLLCFG_PPQ)
 *   Main regulator output voltage : Scale1 mode  Needed for high speed SYSCLK
 *   Flash Latency(WS)             : 5
 *   Prefetch Buffer               : OFF
 *   Instruction cache             : ON
 *   Data cache                    : ON
 *   Require 48MHz for USB OTG FS, : Enabled
 *   SDIO and RNG clock
 */

/* HSI - 16 MHz RC factory-trimmed
 * LSI - 32 KHz RC
 * HSE - On-board crystal frequency is 25MHz
 * LSE - 32.768 kHz
 */

#define STM32_BOARD_XTAL        25000000ul

#define STM32_HSI_FREQUENCY     16000000ul
#define STM32_LSI_FREQUENCY     32000
#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
#define STM32_LSE_FREQUENCY     32768

/* Main PLL Configuration.
 *
 * PLL source is HSE
 * PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN
 *         = (25,000,000 / 25) * 336
 *         = 336,000,000
 * SYSCLK  = PLL_VCO / PLLP
 *         = 336,000,000 / 2 = 168,000,000
 * USB OTG FS, SDIO and RNG Clock
 *         =  PLL_VCO / PLLQ
 *         = 48,000,000
 */

#define STM32_PLLCFG_PLLM       RCC_PLLCFG_PLLM(25)
#define STM32_PLLCFG_PLLN       RCC_PLLCFG_PLLN(336)
#define STM32_PLLCFG_PLLP       RCC_PLLCFG_PLLP_2
#define STM32_PLLCFG_PPQ        RCC_PLLCFG_PLLQ(7)

#define STM32_SYSCLK_FREQUENCY  168000000ul

/* AHB clock (HCLK) is SYSCLK (168MHz) */

#define STM32_RCC_CFGR_HPRE     RCC_CFGR_HPRE_SYSCLK  /* HCLK  = SYSCLK / 1 */
#define STM32_HCLK_FREQUENCY    STM32_SYSCLK_FREQUENCY
#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY  /* same as above, to satisfy compiler */

/* APB1 clock (PCLK1) is HCLK/4 (42MHz) */

#define STM32_RCC_CFGR_PPRE1    RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */
#define STM32_PCLK1_FREQUENCY   (STM32_HCLK_FREQUENCY/4)

/* APB2 clock (PCLK2) is HCLK/2 (84MHz) */

#define STM32_RCC_CFGR_PPRE2    RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */
#define STM32_PCLK2_FREQUENCY   (STM32_HCLK_FREQUENCY/2)

/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
 * otherwise frequency is 2xAPBx. 
 * Note: TIM1,8 are on APB2, others on APB1
 */

#define STM32_TIM18_FREQUENCY   STM32_HCLK_FREQUENCY
#define STM32_TIM27_FREQUENCY   STM32_HCLK_FREQUENCY

/* SDIO dividers.  Note that slower clocking is required when DMA is disabled 
 * in order to avoid RX overrun/TX underrun errors due to delayed responses
 * to service FIFOs in interrupt driven mode.  These values have not been
 * tuned!!!
 *
 * HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz
 */
  
#define SDIO_INIT_CLKDIV        (178 << SDIO_CLKCR_CLKDIV_SHIFT)

/* DMA ON:  HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz
 * DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
 */

#ifdef CONFIG_SDIO_DMA
#  define SDIO_MMCXFR_CLKDIV    (2 << SDIO_CLKCR_CLKDIV_SHIFT) 
#else
#  define SDIO_MMCXFR_CLKDIV    (3 << SDIO_CLKCR_CLKDIV_SHIFT) 
#endif

/* DMA ON:  HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz
 * DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
 */

#ifdef CONFIG_SDIO_DMA
#  define SDIO_SDXFR_CLKDIV     (1 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
#  define SDIO_SDXFR_CLKDIV     (3 << SDIO_CLKCR_CLKDIV_SHIFT)
#endif

/* LED definitions ******************************************************************/

/* The STM3240G-EVAL board has 4 LEDs that we will encode as: */

#define LED_STARTED       0  /* LED1 */
#define LED_HEAPALLOCATE  1  /* LED2 */
#define LED_IRQSENABLED   2  /* LED1 + LED2 */
#define LED_STACKCREATED  3  /* LED3 */
#define LED_INIRQ         4  /* LED1 + LED3 */
#define LED_SIGNAL        5  /* LED2 + LED3 */
#define LED_ASSERTION     6  /* LED1 + LED2 + LED3 */
#define LED_PANIC         7  /* N/C  + N/C  + N/C + LED4 */

/* The STM3240G-EVAL supports three buttons: */

#define BUTTON_WAKEUP      0
#define BUTTON_TAMPER      1
#define BUTTON_USER        2

#define NUM_BUTTONS        3

#define BUTTON_WAKEUP_BIT  (1 << BUTTON_WAKEUP)
#define BUTTON_TAMPER_BIT  (1 << BUTTON_TAMPER)
#define BUTTON_USER_BIT    (1 << BUTTON_USER)

/* Alternate function pin selections ************************************************/

/* UART3:
 * - PC11 is MicroSDCard_D3 & RS232/IrDA_RX (JP22 open)
 * - PC10 is MicroSDCard_D2 & RSS232/IrDA_TX
 */

#define GPIO_USART3_RX GPIO_USART3_RX_2
#define GPIO_USART3_TX GPIO_USART3_TX_2

/************************************************************************************
 * Public Data
 ************************************************************************************/

#ifndef __ASSEMBLY__

#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif

/************************************************************************************
 * Public Function Prototypes
 ************************************************************************************/
/************************************************************************************
 * Name: stm32_boardinitialize
 *
 * Description:
 *   All STM32 architectures must provide the following entry point.  This entry point
 *   is called early in the intitialization -- after all memory has been configured
 *   and mapped but before any devices have been initialized.
 *
 ************************************************************************************/

EXTERN void stm32_boardinitialize(void);

/************************************************************************************
 * Button support.
 *
 * Description:
 *   up_buttoninit() must be called to initialize button resources.  After
 *   that, up_buttons() may be called to collect the current state of all
 *   buttons or up_irqbutton() may be called to register button interrupt
 *   handlers.
 *
 *   After up_buttoninit() has been called, up_buttons() may be called to
 *   collect the state of all buttons.  up_buttons() returns an 8-bit bit set
 *   with each bit associated with a button.  See the BUTTON_*_BIT
 *   definitions in board.h for the meaning of each bit.
 *
 *   up_irqbutton() may be called to register an interrupt handler that will
 *   be called when a button is depressed or released.  The ID value is a
 *   button enumeration value that uniquely identifies a button resource. See the
 *   BUTTON_* definitions in board.h for the meaning of enumeration
 *   value.  The previous interrupt handler address is returned (so that it may
 *   restored, if so desired).
 *
 ************************************************************************************/

#ifdef CONFIG_ARCH_BUTTONS
EXTERN void up_buttoninit(void);
EXTERN uint8_t up_buttons(void);
#ifdef CONFIG_ARCH_IRQBUTTONS
EXTERN xcpt_t up_irqbutton(int id, xcpt_t irqhandler);
#endif
#endif

#undef EXTERN
#if defined(__cplusplus)
}
#endif

#endif /* __ASSEMBLY__ */
#endif  /* __ARCH_BOARD_BOARD_H */