sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
d9029f153c
nuttx/configs/nucleo-f410rb/include/board.h

348 lines
12 KiB
C
Raw Normal View History

configs/nucleo-f410rb: Add support for the nucleo-F410RB board.
2017-09-25 20:59:39 +02:00
/************************************************************************************
* configs/nucleo-f410rb/include/board.h
*
* Copyright (C) 2014, 2016 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_NUCLEO_F410RB_INCLUDE_BOARD_H
#define __CONFIGS_NUCLEO_F410RB_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
#ifdef __KERNEL__
# include "stm32.h"
#endif
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* The NUCLEO410RB supports both HSE and LSE crystals (X2 and X3). However, as
* shipped, the X3 crystals is not populated. Therefore the Nucleo-F410RB
* will need to run off the 16MHz HSI clock.
*
* System Clock source : PLL (HSI)
* SYSCLK(Hz) : 100000000 Determined by PLL configuration
* HCLK(Hz) : 100000000 (STM32_RCC_CFGR_HPRE)
* AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE)
* APB1 Prescaler : 2 (STM32_RCC_CFGR_PPRE1)
* APB2 Prescaler : 1 (STM32_RCC_CFGR_PPRE2)
* HSI Frequency(Hz) : 16000000 (nominal)
* PLLM : 2 (STM32_PLLCFG_PLLM)
* PLLN : 50 (STM32_PLLCFG_PLLN)
* PLLP : 4 (STM32_PLLCFG_PLLP)
* PLLQ : 8 (STM32_PLLCFG_PPQ)
* Flash Latency(WS) : 5
* Prefetch Buffer : OFF
* Instruction cache : ON
* Data cache : ON
*/
/* HSI - 16 MHz RC factory-trimmed
* LSI - 32 KHz RC
* HSE - not installed
* LSE - not installed
*/
#define STM32_HSI_FREQUENCY 16000000ul
#define STM32_LSI_FREQUENCY 32000
#define STM32_BOARD_USEHSI 1
/* Main PLL Configuration.
*
* Formulae:
*
* VCO input frequency = PLL input clock frequency / PLLM, 2 <= PLLM <= 63
* VCO output frequency = VCO input frequency <EFBFBD> PLLN, 50 <= PLLN <= 432
* PLL output clock frequency = VCO frequency / PLLP, PLLP = 2, 4, 6, or 8
* USB OTG FS clock frequency = VCO frequency / PLLQ, 2 <= PLLQ <= 15
*
* We will configure like this
*
* PLL source is HSI
* PLL_VCO = (STM32_HSI_FREQUENCY / PLLM) * PLLN
* = (16,000,000 / 2) * 50
* = 400,000,000
* SYSCLK = PLL_VCO / PLLP
* = 400,000,000 / 4 = 100,000,000
* RNG Clock
* = PLL_VCO / PLLQ
* = 400,000,000 / 8 = 50,000,000
*
* REVISIT: Trimming of the HSI is not yet supported.
*/
#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(2)
#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(50)
#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_4
#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(8)
#define STM32_SYSCLK_FREQUENCY 100000000ul
/* AHB clock (HCLK) is SYSCLK (100MHz) */
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* Same as above, to satisfy compiler */
/* APB1 clock (PCLK1) is HCLK/2 (50MHz) */
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2 /* PCLK1 = HCLK / 2 */
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2)
/* Timers driven from APB1 will be twice PCLK1 */
/* REVISIT */
#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY)
/* APB2 clock (PCLK2) is HCLK (100MHz) */
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK /* PCLK2 = HCLK */
#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY)
/* Timers driven from APB2 will be PCLK2 */
/* REVISIT */
#define STM32_APB2_TIM1_CLKIN (STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM9_CLKIN (STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM11_CLKIN (STM32_PCLK2_FREQUENCY)
/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
* otherwise frequency is 2xAPBx.
* Note: TIM1,9,11 are on APB2, others on APB1
*/
/* REVISIT */
#define BOARD_TIM1_FREQUENCY STM32_APB2_TIM1_CLKIN
#define BOARD_TIM5_FREQUENCY STM32_APB1_TIM5_CLKIN
#define BOARD_TIM6_FREQUENCY STM32_APB1_TIM6_CLKIN
#define BOARD_TIM9_FREQUENCY STM32_APB2_TIM9_CLKIN
#define BOARD_TIM11_FREQUENCY STM32_APB2_TIM11_CLKIN
/* DMA Channel/Stream Selections ****************************************************/
/* Stream selections are arbitrary for now but might become important in the future
* is we set aside more DMA channels/streams.
*/
#define ADC1_DMA_CHAN DMAMAP_ADC1_1
#define GPIO_TIM1_CH1OUT GPIO_TIM1_CH1OUT_1
#define DMACHAN_SPI1_RX DMAMAP_SPI1_RX_1
#define DMACHAN_SPI1_TX DMAMAP_SPI1_TX_1
#define DMACHAN_SPI2_RX DMAMAP_SPI2_RX
#define DMACHAN_SPI2_TX DMAMAP_SPI2_TX
/* Alternate function pin selections ************************************************/
/* USART1:
* RXD: PA10 CN9 pin 3, CN10 pin 33
* PB7 CN7 pin 21
* TXD: PA9 CN5 pin 1, CN10 pin 21
* PB6 CN5 pin 3, CN10 pin 17
*/
#if 1
# define GPIO_USART1_RX GPIO_USART1_RX_1 /* PA10 */
# define GPIO_USART1_TX GPIO_USART1_TX_1 /* PA9 */
#else
# define GPIO_USART1_RX GPIO_USART1_RX_2 /* PB7 */
# define GPIO_USART1_TX GPIO_USART1_TX_2 /* PB6 */
#endif
/* USART2:
* RXD: PA3 CN9 pin 1 (See SB13, 14, 62, 63). CN10 pin 37
* PD6
* TXD: PA2 CN9 pin 2(See SB13, 14, 62, 63). CN10 pin 35
* PD5
*/
#define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */
#define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */
#define GPIO_USART2_RTS GPIO_USART2_RTS_2
#define GPIO_USART2_CTS GPIO_USART2_CTS_2
/* USART6:
* RXD: PC7 CN5 pin2, CN10 pin 19
* PA12 CN10, pin 12
* TXD: PC6 CN10, pin 4
* PA11 CN10, pin 14
*/
#define GPIO_USART6_RX GPIO_USART6_RX_1 /* PC7 */
#define GPIO_USART6_TX GPIO_USART6_TX_1 /* PC6 */
/* UART RX DMA configurations */
#define DMAMAP_USART1_RX DMAMAP_USART1_RX_2
#define DMAMAP_USART6_RX DMAMAP_USART6_RX_2
/* I2C
*
* The optional _GPIO configurations allow the I2C driver to manually
* reset the bus to clear stuck slaves. They match the pin configuration,
* but are normally-high GPIOs.
*/
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2
#define GPIO_I2C1_SCL_GPIO \
(GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN8)
#define GPIO_I2C1_SDA_GPIO \
(GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9)
#define GPIO_I2C2_SCL GPIO_I2C2_SCL_1
#define GPIO_I2C2_SDA GPIO_I2C2_SDA_1
#define GPIO_I2C2_SCL_GPIO \
(GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN10)
#define GPIO_I2C2_SDA_GPIO \
(GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN11)
/* SPI
*
*/
#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1
#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1
#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1
#define GPIO_SPI2_MISO GPIO_SPI2_MISO_1
#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1
#define GPIO_SPI2_SCK GPIO_SPI2_SCK_2
/* LEDs
*
* The Nucleo F410RB board provide a single user LED, LD2. LD2
* is the green LED connected to Arduino signal D13 corresponding to MCU I/O
* PA5 (pin 21) or PB13 (pin 34) depending on the STM32 target.
*
* - When the I/O is HIGH value, the LED is on.
* - When the I/O is LOW, the LED is off.
*/
/* LED index values for use with board_userled() */
#define BOARD_LD2 0
#define BOARD_NLEDS 1
/* LED bits for use with board_userled_all() */
#define BOARD_LD2_BIT (1 << BOARD_LD2)
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
* defined. In that case, the usage by the board port is defined in
* include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
* events as follows when the red LED (PE24) is available:
*
* SYMBOL Meaning LD2
* ------------------- ----------------------- -----------
* LED_STARTED NuttX has been started OFF
* LED_HEAPALLOCATE Heap has been allocated OFF
* LED_IRQSENABLED Interrupts enabled OFF
* LED_STACKCREATED Idle stack created ON
* LED_INIRQ In an interrupt No change
* LED_SIGNAL In a signal handler No change
* LED_ASSERTION An assertion failed No change
* LED_PANIC The system has crashed Blinking
* LED_IDLE MCU is is sleep mode Not used
*
* Thus if LD2, NuttX has successfully booted and is, apparently, running
* normally. If LD2 is flashing at approximately 2Hz, then a fatal error
* has been detected and the system has halted.
*/
#define LED_STARTED 0
#define LED_HEAPALLOCATE 0
#define LED_IRQSENABLED 0
#define LED_STACKCREATED 1
#define LED_INIRQ 2
#define LED_SIGNAL 2
#define LED_ASSERTION 2
#define LED_PANIC 1
/* Buttons
*
* B1 USER: the user button is connected to the I/O PC13 (pin 2) of the STM32
* microcontroller.
*/
#define BUTTON_USER 0
#define NUM_BUTTONS 1
#define BUTTON_USER_BIT (1 << BUTTON_USER)
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/************************************************************************************
* Name: stm32_boardinitialize
*
* Description:
* All STM32 architectures must provide the following entry point. This entry point
* is called early in the initialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
void stm32_boardinitialize(void);
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_NUCLEO_F410RB_INCLUDE_BOARD_H */
Reference in New Issue Copy Permalink