nuttx/configs/indium-f7/Kconfig

#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

comment "Using Nucleo-144-F7 Board."
choice
	prompt "Select Clock Source."
	default INDIUM_CLOCK_MCO
	---help---
		Select the final clock source.

		MCO - Clock provided by the ST-LINK

		HSI - Internal High Speed Oscillator.

config INDIUM_CLOCK_MCO
	bool "MCO 8-MHz"

config INDIUM_CLOCK_HSI
	bool "HSI 16-MHz"

endchoice # "Select Clock Source."

choice
	prompt "Select Console wiring."
	default INDIUM_CONSOLE_MORPHO_UART4
	---help---
		Select where you will connect the console.

		Virtual COM Port:

		Advantage: Use the ST-Link as a console. No Extra wiring
		neded.

		Disdvantage: Not the best choice for initanl bring up.

		ARDUINO Connector:

		Advantage: You have a shield so it is
		easy.

		Disdvantage: You loose the use of the
		other functions on PC6, PC7

				STM32F7
			ARDUIONO FUNCTION  GPIO
			-- ----- --------- ----
			DO RX    USART6_RX PG9
			D1 TX    USART6_TX PG14
			-- ----- --------- ---

					OR

		Morpho Connector:

				STM32F7
			MORPHO   FUNCTION  GPIO
			-------- --------- -----
			CN12-64  UART8_RX  PE0
			CN11-61  UART8_TX  PE1
			-------- --------- -----

					OR

		Morpho Connector UART4:

				STM32F7
			MORPHO   FUNCTION  GPIO
			-------- --------- -----
			CN11-30  UART4_RX  PA0
			CN11-28  UART4_TX  PA1
			-------- --------- -----
			Note: SB13 must be removed to disable Ethernet.

config INDIUM_CONSOLE_ARDUINO
	bool "Arduino Connector"
	select STM32F7_USART6
	select USART6_SERIALDRIVER
	select USART6_SERIAL_CONSOLE

config INDIUM_CONSOLE_VIRTUAL
	bool "Virtual Comport"
	select STM32F7_USART3
	select USART3_SERIALDRIVER
	select USART3_SERIAL_CONSOLE

config INDIUM_CONSOLE_MORPHO
	bool "Morpho Connector"
	select STM32F7_UART8
	select UART8_SERIALDRIVER
	select UART8_SERIAL_CONSOLE

config INDIUM_CONSOLE_MORPHO_UART4
	bool "Morpho Connector UART4"
	select STM32F7_UART4
	select UART4_SERIALDRIVER
	select UART4_SERIAL_CONSOLE

config INDIUM_CONSOLE_NONE
	bool "No Console"

endchoice # "Select Console wiring"

config NUCLEO_SPI_TEST
	bool "Enable SPI test"
	default n
	---help---
		Enable Spi test - initalize and configure SPI to send
		NUCLEO_SPI_TEST_MESSAGE text. The text is sent on the
		selected SPI Buses with the configured parameters.
		Note the CS lines will not be asserted.

if NUCLEO_SPI_TEST

config NUCLEO_SPI_TEST_MESSAGE
	string "Text to Send on SPI Bus(es)"
	default "Hello World"
	depends on NUCLEO_SPI_TEST
	---help---
		Text to sent on SPI bus(es)

config NUCLEO_SPI1_TEST
	bool "Test SPI bus 1"
	default n
	depends on NUCLEO_SPI_TEST
	---help---
		Enable Spi test - on SPI BUS 1

if NUCLEO_SPI1_TEST

config NUCLEO_SPI1_TEST_FREQ
	int "SPI 1 Clock Freq in Hz"
	default 1000000
	depends on NUCLEO_SPI1_TEST
	---help---
		Sets SPI 1 Clock Freq

config NUCLEO_SPI1_TEST_BITS
	int "SPI 1 number of bits"
	default 8
	depends on NUCLEO_SPI1_TEST
	---help---
		Sets SPI 1 bit length

choice
	prompt "SPI BUS 1 Clock Mode"
	default INDIUM_SPI1_TEST_MODE3
	---help---
		Sets SPI 1 clock mode

config INDIUM_SPI1_TEST_MODE0
	bool "CPOL=0 CHPHA=0"

config INDIUM_SPI1_TEST_MODE1
	bool "CPOL=0 CHPHA=1"

config INDIUM_SPI1_TEST_MODE2
	bool "CPOL=1 CHPHA=0"

config INDIUM_SPI1_TEST_MODE3
	bool "CPOL=1 CHPHA=1"

endchoice # "SPI BUS 1 Clock Mode"

endif # INDIUM_SPI1_TEST

config NUCLEO_SPI2_TEST
	bool "Test SPI bus 2"
	default n
	depends on NUCLEO_SPI_TEST
	---help---
		Enable Spi test - on SPI BUS 2

if INDIUM_SPI2_TEST

config NUCLEO_SPI2_TEST_FREQ
	int "SPI 2 Clock Freq in Hz"
	default 12000000
	depends on NUCLEO_SPI2_TEST
	---help---
		Sets SPI 2 Clock Freq

config NUCLEO_SPI2_TEST_BITS
	int "SPI 2 number of bits"
	default 8
	depends on NUCLEO_SPI2_TEST
	---help---
		Sets SPI 2 bit length

choice
	prompt "SPI BUS 2 Clock Mode"
	default INDIUM_SPI2_TEST_MODE3
	---help---
		Sets SPI 2 clock mode

config INDIUM_SPI2_TEST_MODE0
	bool "CPOL=0 CHPHA=0"

config INDIUM_SPI2_TEST_MODE1
	bool "CPOL=0 CHPHA=1"

config INDIUM_SPI2_TEST_MODE2
	bool "CPOL=1 CHPHA=0"

config INDIUM_SPI2_TEST_MODE3
	bool "CPOL=1 CHPHA=1"

endchoice # "SPI BUS 2 Clock Mode"

endif # NUCLEO_SPI2_TEST
endif # NUCLEO_SPI_TEST