nuttx/configs/lpcxpresso-lpc54628/README.txt

README
======

  This directory contains the port to the NXP LPCXpress-LPC54628 board
  (OMI1309UL).  This board features:

    - LPC54628 Cortex-M4 microcontroller running at up to 220MHz
    - 272x480 color LCD with capacitive touch screen
    - On-board, high-speed USB, Link2 debug probe with CMSIS-DAP and SEGGER
      J-Link protocol options
    - UART and SPI port bridging from LPC546xx target to USB via the on-
      board debug probe
    - Support for external debug probe
    - 3 x user LEDs, plus Reset, ISP (3) and user buttons
    - Multiple Expansion options, including Arduino UNO and PMod
    - Built-in power consumption measurement for target LPC546xx MCU
    - 128Mb Micron MT25QL128 Quad-SPI flash
    - 16MB Micron MT48LC8M16A2B4 SDRAM
    - Knowles SPH0641LM4H digital microphone
    - Full size SD/MMC card slot
    - NXP MMA8652FCR1 accelerometer
    - Stereo audio codec with line in/out
    - High and full speed USB ports with micro A/B connector for host or
      device functionality
    - 10/100Mbps Ethernet (RJ45 connector)

STATUS
======

  2017-12-10:  The basic NSH configuration is functional at 220MHz with a
    Serial console, timer and LED support.  Added support for the external
    SDRAM and for the RAM test utility.
  2017-12-11:  Fixed an error in board LEDs.  Added framework for future
    I2C and SPI flexcomm drivers.
  2017-12-12:  The SDRAM is now functional and passes the commplete RAM
    test.  Added configuration options and logic to add none, portions, or
    all of the external SDRAM to the system heap.  Brought in the LPC1788
    LCD driver.  The LPC1788 LCD registers are identical to the LPC54xx
    (other than a minor clock source setting).
  2017-12-13:  Created the fb configuration for testing the LCD.
  2017-12-14:  Corrected a misconception about how the video data lines
    were configured.  The LCD now appears to be fully functional.
  2017-12-15:  Added an I2C driver.
  2017-12-16:  Added support for LPC54xx GPIO interrupts; added button
    support (with interrupts) to the NSH configuration.  The button
    test appears to functional functional.  There are noticeable delays
    in receiving the button events, especially when the button is
    released.  But if you do not press the buttons too quickly all events
    are processed.  This, I suspect, is a consequence of the strong glitch
    filtering that is enbled in the pin configuration.  Snappier
    response my be obtainble with filtering off.
  2017-12-17:  Added a driver for the FT5x06 capacitive, multi-touch
    controller.  Add support logic for the LPCXpresso-LPC54528 to
    initialize and the register the FT5x06 driver.  Unfortunately, the
    FT5x06 interrupt is on pin P4.0 but pin interrupts are only supported
    on P0.m and P1.m, m=0..31.
  2017-12-18:  Added an option to the FT5x06 driver to support a timer-
    based poll instead of interrupts.  This is very inefficient in that it
    will introduce delays in touchscreen response and will consume more CPU
    bandwidth.  The driver appears to be functional.  Added the NxWM
    configuration to do some integrated testing.  NxWM seems to be fully
    functional.  However, the action of the touchscreen could use some
    human factors improvements.  I imagine that this is a consequence of
    the polled solution.
  2017-12-19:  Brought in Alan Carvalho de Assis' LPC43xx SD/MMC driver from
    https://github.com/Smoothieware/smoothie-nuttx/tree/master/nuttx/arch/arm/src/lpc43xx
    and adapted it for use by the LPC54xx.  Unverified as of this writing.
  2017-12-21:  Some things are working with he SDMMC drivers but read DMAs
    are non-functional and, hence not usable.
  2017-12-23:  SDMMC is still non-functional.  The first DMA read of 512 bytes
    fails with a CRC error.  Similar result if clock is reduced, if 1-bit bus
    is used, if DMA is disabled., if DEBUG output is disabled.
  2017-12-24:  Added basic DMA support; brought in the WWDT driver from the
    LPC43 which has the same peripheral.  Neither tested; almost certainly
    non-functional without some additional investment.
  2017-12-25:  Added an RTC driver.  It appears to be functional but has not
    been well tested.
  2017-12-26:  Added an RNG driver.  The RNG is actually controlled by a ROM
    function.  This driver seems to work fine when single stepping.  However,
    if I collect samples indefinitely, I get a reserved interrupt.  The symptom
    before the crash is that local variables are getting corrupted after the
    call into ROM. Increasing the stack size does not seem to help.  Perhaps
    to use the ROM at high frequencies it may be necessary to modify the ROM
    access timing in some way???
  2017-12-30:  Completed implementation of an Ethernet driver.  Untested as
    of this writing.  Also added the netnsh configuration will, eventually,
    be used to test the Ethernet diver.

  There is still no support for the Accelerometer, SPIFI, or USB.  There are
  complete but not-yet-functional SD card and Ethernet drivers.  There is a
  partial SPI driver, but no on-board SPI devices to test it.

Configurations
==============

  Information Common to All Configurations
  ----------------------------------------
  Each LPCXpresso-LPC54628 configuration is maintained in a sub-directory
  and can be selected as follow:

    .tools/configure.sh [OPTIONS] lpcxpresso-lpc54628/<subdir>

  See '.tools/configure.sh -h' for a list of all options.  The most typical
  are -l to select the Linux host or -c to select the Windows Cygwin host.

  Before starting the build, make sure that your PATH environment variable
  includes the correct path to your toolchain.

  And then build NuttX by simply typing the following.  At the conclusion of
  the make, the nuttx binary will reside in an ELF file called, simply, nuttx.

    make

  The <subdir> that is provided above as an argument to the tools/configure.sh
  must be is one of the following.

  NOTES:

    1. These configurations use the mconf-based configuration tool.  To
      change any of these configurations using that tool, you should:

      a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
         see additional README.txt files in the NuttX tools repository.

      b. Execute 'make menuconfig' in nuttx/ in order to start the
         reconfiguration process.

    2. Unless stated otherwise, all configurations generate console
       output on USART0 (aka Flexcomm0).  USART0 connects to the serial
       bridge on LPC4322JET100 and should be available as a USB serial
       device on your host PC.

    3. All of these configurations are set up to build under Windows using
       the  "GNU Tools for ARM Embedded Processors" that is maintained by
       ARM (unless stated otherwise in the description of the configuration).

         https://developer.arm.com/open-source/gnu-toolchain/gnu-rm

       That toolchain selection can easily be reconfigured using
       'make menuconfig'.  Here are the relevant current settings:

       Build Setup:
         CONFIG_HOST_WINDOWS=y               : Window environment
         CONFIG_WINDOWS_CYGWIN=y             : Cywin under Windows

       System Type -> Toolchain:
         CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIW=y : GNU ARM EABI toolchain

  Configuration sub-directories
  -----------------------------

  fb:

    A simple NSH configuration used for some basic debug of LCD using the
    framebuffer character drivers.  This configuration provides the test
    programs:

      - apps/examples/pdcurses, and
      - apps/examples/fb

    as NSH built-in applications.

    NOTES:
    1. This configuration enables SDRAM to hold the LCD framebuffer and
       enables the LPC54xx LCD driver in order to support the LPCXpresso's
       TFT panel.  In this configuration, the framebuffer resides in the
       the lower half megabyte of SDRAM beginning at address 0xa0000000
       The remainder of the SDRAM from 0xa0080000 up to 0xa1000000 is added
       to the heap.

       The is wasteful of SDRAM:  Only 261,120 bytes actually used for the
       framebuffer.  This memory could be reclaimed by changing the DRAM
       CS0 offset value in the .config file.

    2. Some of the pdcurses test rely on some positional input device and so
       is not yet usable.  Others work fine with no user include:  charset,
       xmas, firework, worms, rain, for examples.

    3. I2C2 is enabled (will be used with the capacitive touchscreen).  In
       order to verify I2C functionality, the I2C tool at apps/system/i2ctool
       is enabled in this configuration.

         nsh> i2c dev -b 2 3 77
              0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
         00:          -- -- -- -- -- -- -- -- -- -- -- -- --
         10: -- -- -- -- -- -- -- -- -- -- 1a -- -- 1d -- --
         20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         30: -- -- -- -- -- -- -- -- 38 -- -- -- -- -- -- --
         40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         70: -- -- -- -- -- -- -- --

         Codec I2C address:        0x1a
         Accel I2C address:        0x1d
         Touch panel I2C address:  0x38

    4. The touchscreen test program at apps/examples/touchscreen is also
       included in this configuration.

         nsh> tc 5
         tc_main: nsamples: 2
         tc_main: Initializing external touchscreen device
         tc_main: Opening /dev/input0
         Sample     :
            npoints : 1
         Point 1    :
                 id : 0
              flags : 1a
                  x : 230
                  y : 84
                  h : 0
                  w : 0
           pressure : 0
         etc.

      NOTE that the touchscreen controlled must run in a polled mode!  The
      FT5x06 interrupt GPIO is on P4.0 and, as far as I know, GPIO
      interrupts are not supported on P4.  So polled mode only for this
      puppy.

  netnsh:
  ------
    This is a special version of the NuttShell (nsh) configuration that is
    tailored for network testing.  This version derives from nsh
    configuration so manhy of the notes apply there except as noted below.

    NOTES:

    1. Networking is enabled.  The LPCXpressio-LPC54628 has an SMC _LAN8720 PHY
       and RJ45 network connector.  Support is enabled for IPv4, IPv6, TCP/IP,
       UDP, ICMP, ICMPv6, and ARP.

    2. SD card and I2C support are not enabled.  The I2C tool application is
       not enabled

    3. SDRAM support is enabled and the SDRAM is added to the system heap. The
       Ramtest applications is not enabled.

    4. This configuration does not include support for aysnchronous network
       initialization.  As a consequence, NSH must bring up the network
       before you get the NSH prompt.  If the network cable is unplugged,
       this can mean a significant delay before you see the prompt.

    5. In this configuration, the network network does not come up
       automatically after it has been initialized.  You will need to
       explicitly bring the network up from the NSH command line:

         nsh> ifup eth0

  nsh:

    Configures the NuttShell (nsh) application located at examples/nsh.
    This configuration was used to bring up the board support and, hence,
    is focused on low level, command-line driver testing.  It has no
    network.

    NOTES:

    1. NSH built-in applications are supported.

       Binary Formats:
         CONFIG_BUILTIN=y           : Enable support for built-in programs

       Application Configuration:
         CONFIG_NSH_BUILTIN_APPS=y  : Enable starting apps from NSH command line

    2. SDRAM support is enabled, but the SDRAM is *not* added to the system
       heap.  The apps/system/ramtest utility is include in the build as an
       NSH builtin function that can be used to verify the SDRAM.

         nsh> ramtest -h
         RAMTest: Missing required arguments

         Usage: <noname> [-w|h|b] <hex-address> <decimal-size>

         Where:
           <hex-address> starting address of the test.
           <decimal-size> number of memory locations (in bytes).
           -w Sets the width of a memory location to 32-bits.
           -h Sets the width of a memory location to 16-bits (default).
           -b Sets the width of a memory location to 8-bits.

       The  MTL48LC8M16A2B4-6A SDRAM is on CS0 which corresponds to address
       0xa0000000, the size of the memory is 128Mbits or 16Mb.  So the DRAM
       may be tested with this command:

         NuttShell (NSH) NuttX-7.23
         nsh> ramtest a0000000 16777216
         RAMTest: Marching ones: a0000000 16777216
         RAMTest: Marching zeroes: a0000000 16777216
         RAMTest: Pattern test: a0000000 16777216 55555555 aaaaaaaa
         RAMTest: Pattern test: a0000000 16777216 66666666 99999999
         RAMTest: Pattern test: a0000000 16777216 33333333 cccccccc
         RAMTest: Address-in-address test: a0000000 16777216
         nsh>

    3. I2C2 is enabled (will be used with the capacitive touchscreen).  In
       order to verify I2C functionality, the I2C tool at apps/system/i2ctool
       is enabled in this configuration.

         nsh> i2c bus
          BUS   EXISTS?
         Bus 0: NO
         Bus 1: NO
         Bus 2: YES
         Bus 3: NO
         Bus 4: NO
         Bus 5: NO
         Bus 6: NO
         Bus 7: NO
         Bus 8: NO
         Bus 9: NO
         nsh> i2c dev -b 2 3 77
              0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
         00:          -- -- -- -- -- -- -- -- -- -- -- -- --
         10: -- -- -- -- -- -- -- -- -- -- 1a -- -- 1d -- --
         20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
         70: -- -- -- -- -- -- -- --

       I believe that the on-board Accelerometer, Audio Codec, and touch
       panel controller should have been detected (but perhaps the touch
       panel is not powered in this configuration since the LCD is not
       configured?)

         Codec I2C address:        0x1a
         Accel I2C address:        0x1d
         Touch panel I2C address:  0x38

    4. Support for the on-board USER button is included as well as the
       button test program at apps/examples/buttons.  This test is useful
       for verifying the functionality of GPIO interrupts.

         NuttShell (NSH) NuttX-7.23
         nsh> buttons
         buttons_main: Starting the button_daemon
         buttons_main: button_daemon started
         button_daemon: Running
         button_daemon: Opening /dev/buttons
         button_daemon: Supported BUTTONs 0x01
         nsh> Sample = 1
         Sample = 0
         Sample = 1
         Sample = 0
         Sample = 1
         Sample = 0
         Sample = 1
         etc.

       There are noticeable delays in receiving the button events,
       especially when the button is released.  But if you do not press the
       buttons too quickly all events are processed.  This, I suspect, is a
       consequence of the strong glitch filtering that is enbled in the pin
       configuration.  Snappier response my be obtainble with filtering off
       if desired.

    5. This configuration has been used for testing the SDMMC driver with
       these configuration additions:

         CONFIG_EXPERIMENTAL=y

         CONFIG_LPC54_SDMMC=y
         CONFIG_LPC54_SDMMC_PWRCTRL=y
         CONFIG_LPC54_SDMMC_DMA=y

         CONFIG_SIG_SIGWORK=17
         CONFIG_SCHED_WORKQUEUE=y
         CONFIG_SCHED_HPWORK=y
         CONFIG_SCHED_HPWORKPRIORITY=224
         CONFIG_SCHED_HPWORKPERIOD=50000
         CONFIG_SCHED_HPWORKSTACKSIZE=2048

         CONFIG_MMCSD=y
         CONFIG_MMCSD_NSLOTS=1
         CONFIG_MMCSD_MULTIBLOCK_DISABLE=y
         CONFIG_MMCSD_HAVE_CARDDETECT=y
         CONFIG_MMCSD_HAVE_WRITEPROTECT=y
         CONFIG_ARCH_HAVE_SDIO=y
         CONFIG_SDIO_DMA=y
         CONFIG_MMCSD_SDIO=y

         CONFIG_NSH_MMCSDSLOTNO=0

    6. The RTC is enabled in this configuration.

         NuttShell (NSH) NuttX-7.23
         nsh> date
         Jan 01 00:00:06 1970
         nsh> date -s "DEC 25 08:00:00 2017"
         nsh> date
         Dec 25 08:00:01 2017

       After reset:

         NuttShell (NSH) NuttX-7.23
         nsh> date
         Dec 25 08:00:05 2017

  nxwm:

    This is a special configuration setup for the NxWM window manager
    UnitTest.  This builds on top of the features that were unit tested in
    by the fb configuration.

    The NxWM window manager can be found here:

      <nuttx-code>/NxWidgets/nxwm

    The NxWM unit test can be found at:

      <nuttx-code>/NxWidgets/UnitTests/nxwm

    Documentation for installing the NxWM unit test can be found here:

      <nuttx-code>/NxWidgets/UnitTests/README.txt

    Where <nuttx-code> is whatever path you have select to install
    NuttX.

    Here is the quick summary of the build steps (Assuming that all of
    the required packages are available in a directory ~/<nuttx-code>):

    1. Install the nxwm configuration

       $ cd ~/<nuttx-code>/nuttx
       $ tools/configure.sh [OPTIONS] lpcxpresso-lpc54628/nxwm

       Use the -l option with the configure.sh script if you are using a
       Linux host; use the -c option if you are using Cygwin under Windows.
       Use the -h option to see other selections.

    2. Make the build context (only)

       $ make context

    3. Install the nxwm unit test

       $ cd ~/<nuttx-code>/NxWidgets
       $ tools/install.sh ~/<nuttx-code>/apps nxwm
       Creating symbolic link
        - To ~/<nuttx-code>/NxWidgets/UnitTests/nxwm
        - At ~/<nuttx-code>/apps/external

    4. Build the NxWidgets library

       $ cd ~/<nuttx-code>/NxWidgets/libnxwidgets
       $ make TOPDIR=~/<nuttx-code>/nuttx

    5. Build the NxWM library

       $ cd ~/<nuttx-code>/NxWidgets/nxwm
       $ make TOPDIR=~/<nuttx-code>/nuttx

    6. Built NuttX with the installed unit test as the application

       $ cd ~/<nuttx-code>/nuttx
       $ make