nuttx/configs/freedom-kl25z/include/board.h

/************************************************************************************
 * configs/kwikstik-k40/include/board.h
 * include/arch/board/board.h
 *
 *   Copyright (C) 2013 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ************************************************************************************/

#ifndef __ARCH_BOARD_BOARD_H
#define __ARCH_BOARD_BOARD_H

/************************************************************************************
 * Included Files
 ************************************************************************************/

#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif

/************************************************************************************
 * Definitions
 ************************************************************************************/

/* Clocking *************************************************************************/
/* The Kwikstik-K40 has a 4MHz crystal on board */

#undef  BOARD_EXTCLOCK                      /* Crystal */
#define BOARD_XTAL_FREQ      8000000        /* 8MHz crystal frequency (REFCLK) */
#define BOARD_XTAL32_FREQ    32768          /* 32KHz RTC Oscillator */

/* PLL Configuration.
 *
 *   PLL Input frequency:   PLLIN     = REFCLK / PRDIV0 = 8MHz / 2 = 4MHz
 *   PLL Output frequency:  PLLOUT    = PLLIN * VDIV0   = 4Mhz * 24 = 96MHz
 *   MCGPLLCLK Frequency:   MCGPLLCLK = 96MHz
 */

#define BOARD_PRDIV0         2              /* PLL External Reference Divider */
#define BOARD_VDIV0          24             /* PLL VCO Divider (frequency multiplier) */

#define BOARD_PLLIN_FREQ     (BOARD_XTAL_FREQ / BOARD_PRDIV0)
#define BOARD_PLLOUT_FREQ    (BOARD_PLLIN_FREQ * BOARD_VDIV0)
#define BOARD_MCGPLLCLK_FREQ  BOARD_PLLOUT_FREQ

/* MCGOUTCLK: MCG output of either IRC, MCGFLLCLK, MCGPLLCLK, or MCG's external
 * reference clock that sources the core, system, bus, and flash clock.
 *
 * MCGOUTCLK = MCGPLLCLK = 96MHz
 */

#define BOARD_MCGOUTCLK_FREQ  BOARD_MCGPLLCLK_FREQ

/* SIM CLKDIV1 dividers.
 *
 * Core/system clock
 *   MCGOUTCLK divided by OUTDIV1, clocks the ARM Cortex-M0+ core
 *
 * Bus clock
 *   System clock divided by OUTDIV4, clocks the bus slaves and peripherals.
 */

#define BOARD_OUTDIV1        2              /* Core/system = MCGOUTCLK / 2, 48MHz */
#define BOARD_OUTDIV4        2              /* Bus clock   = System clock / 2, 24MHz */

#define BOARD_CORECLK_FREQ  (BOARD_MCGOUTCLK_FREQ / BOARD_OUTDIV1)
#define BOARD_BUSCLK_FREQ   (BOARD_CORECLK_FREQ / BOARD_OUTDIV4)

/* SDHC clocking ********************************************************************/

/* SDCLK configurations corresponding to various modes of operation.   Formula is:
 *
 *   SDCLK  frequency = (base clock) / (prescaler * divisor)
 *
 * The SDHC module is always configure configured so that the core clock is the base
 * clock.
 */

/* Identification mode:  400KHz = 96MHz / ( 16 * 15) */

#define BOARD_SDHC_IDMODE_PRESCALER   SDHC_SYSCTL_SDCLKFS_DIV16
#define BOARD_SDHC_IDMODE_DIVISOR     SDHC_SYSCTL_DVS_DIV(15)

/* MMC normal mode: 16MHz  = 96MHz / (2 * 3) */

#define BOARD_SDHC_MMCMODE_PRESCALER  SDHC_SYSCTL_SDCLKFS_DIV2
#define BOARD_SDHC_MMCMODE_DIVISOR    SDHC_SYSCTL_DVS_DIV(3)

/* SD normal mode (1-bit): 16MHz  = 96MHz / (2 * 3) */

#define BOARD_SDHC_SD1MODE_PRESCALER  SDHC_SYSCTL_SDCLKFS_DIV2
#define BOARD_SDHC_SD1MODE_DIVISOR    SDHC_SYSCTL_DVS_DIV(3)

/* SD normal mode (4-bit): 24MHz  = 96MHz / (2 * 2) (with DMA)
 * SD normal mode (4-bit): 16MHz  = 96MHz / (2 * 3) (no DMA)
 */

#ifdef CONFIG_SDIO_DMA
#  define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
#  define BOARD_SDHC_SD4MODE_DIVISOR   SDHC_SYSCTL_DVS_DIV(2)
#else
//#  define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
//#  define BOARD_SDHC_SD4MODE_DIVISOR   SDHC_SYSCTL_DVS_DIV(3)
#  define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV16
#  define BOARD_SDHC_SD4MODE_DIVISOR   SDHC_SYSCTL_DVS_DIV(15)
#endif

/* PWM Configuration */
/* TPM0 Channels */

#define GPIO_TPM0_CH0OUT PIN_TPM0_CH0_3 //PIN_TPM0_CH0_1
#define GPIO_TPM0_CH1OUT PIN_TPM0_CH1_1
#define GPIO_TPM0_CH2OUT PIN_TPM0_CH2_1
#define GPIO_TPM0_CH3OUT PIN_TPM0_CH3_1
#define GPIO_TPM0_CH4OUT PIN_TPM0_CH4_1
#define GPIO_TPM0_CH5OUT PIN_TPM0_CH5_1

/* TPM1 Channels */

#define GPIO_TPM1_CH0OUT PIN_TPM1_CH0_1
#define GPIO_TPM1_CH1OUT PIN_TPM1_CH1_1

/* TPM2 Channels */

#define GPIO_TPM1_CH0OUT PIN_TPM2_CH0_1
#define GPIO_TPM1_CH1OUT PIN_TPM2_CH1_1

/* LED definitions ******************************************************************/
/* The Freedom KL25Z has a single RGB LED driven by the KL25Z as follows:
 *
 *   ------------- --------
 *   RGB LED       KL25Z128
 *   ------------- --------
 *   Red Cathode   PTB18
 *   Green Cathode PTB19
 *   Blue Cathode  PTD1
 *
 * NOTE: PTD1 is also connected to the I/O header on J2 pin 10 (also known as D13).
 *
 * If CONFIG_ARCH_LEDs is defined, then NuttX will control the LED on board the
 * Freedom KL25Z.  The following definitions describe how NuttX controls the LEDs:
 *
 *   SYMBOL                Meaning                 LED state
 *                                                 Initially all LED is OFF
 *   -------------------  -----------------------  --------------------------
 *   LED_STARTED          NuttX has been started   R=OFF G=OFF B=OFF
 *   LED_HEAPALLOCATE     Heap has been allocated  (no change)
 *   LED_IRQSENABLED      Interrupts enabled       (no change)
 *   LED_STACKCREATED     Idle stack created       R=OFF G=OFF B=ON
 *   LED_INIRQ            In an interrupt          (no change)
 *   LED_SIGNAL           In a signal handler      (no change)
 *   LED_ASSERTION        An assertion failed      (no change)
 *   LED_PANIC            The system has crashed   R=FLASHING G=OFF B=OFF
 *   LED_IDLE             K25Z1XX is in sleep mode (Optional, not used)
 */

#define LED_STARTED       0
#define LED_HEAPALLOCATE  1
#define LED_IRQSENABLED   2
#define LED_STACKCREATED  3
#define LED_INIRQ         4
#define LED_SIGNAL        5
#define LED_ASSERTION     6
#define LED_PANIC         7

/* Button definitions ***************************************************************/
/* The Freedom KL25Z board has no standard GPIO contact buttons */

/* Alternative pin resolution *******************************************************/
/* If there are alternative configurations for various pins in the k25z128_pinmux.h
 * header file, those alternative pins will be labeled with a suffix like _1, _2,
 * etc.  The logic in this file must select the correct pin configuration for the
 * board by defining a pin configuration (with no suffix) that maps to the correct
 * alternative.
 */

#define PIN_SPI0_SCK   (PIN_SPI0_SCK_2 | PIN_ALT2_PULLUP)
#define PIN_SPI0_MISO  (PIN_SPI0_MISO_4 | PIN_ALT2_PULLUP)
#define PIN_SPI0_MOSI  (PIN_SPI0_MOSI_3 | PIN_ALT2_PULLUP)

#define PIN_SPI1_SCK   (PIN_SPI1_SCK_2 | PIN_ALT2_PULLUP)
#define PIN_SPI1_MISO  (PIN_SPI1_MISO_3 | PIN_ALT2_PULLUP)
#define PIN_SPI1_MOSI  (PIN_SPI0_MOSI_7 | PIN_ALT2_PULLUP)

/* These pins are used by CC3000 module */

#define GPIO_WIFI_EN (GPIO_OUTPUT | GPIO_OUTPUT_ZER0 | PIN_PORTC | PIN12)
#define GPIO_WIFI_IRQ (GPIO_INPUT | PIN_PORTA | PIN16)
#define GPIO_WIFI_CS (GPIO_OUTPUT | GPIO_OUTPUT_ONE | PIN_PORTE | PIN1)

/* Interrupt pin used by ADXL345 */

#define GPIO_ADXL345_INT1 (GPIO_INPUT | PIN_PORTA | PIN_INT_RISING | PIN4)
#define GPIO_ADXL345_CS   (GPIO_OUTPUT | GPIO_OUTPUT_ONE | PIN_PORTD | PIN0)

/************************************************************************************
 * Public Data
 ************************************************************************************/

#ifndef __ASSEMBLY__

#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif

/************************************************************************************
 * Public Function Prototypes
 ************************************************************************************/
/************************************************************************************
 * Name: kl_boardinitialize
 *
 * Description:
 *   All Kinetis L architectures must provide the following entry point.  This entry
 *   point is called early in the intitialization -- after all memory has been
 *   configured and mapped but before any devices have been initialized.
 *
 ************************************************************************************/

void kl_boardinitialize(void);

/************************************************************************************
 * Name: kl_tsi_initialize
 *
 * Description:
 *   Initialize the TSI hardware and interface for the sliders on board the Freedom
 *   KL25Z board.  Register a character driver at /dev/tsi that may be used to read
 *   from each sensor.
 *
 ************************************************************************************/

#ifdef CONFIG_KL_TSI
void kl_tsi_initialize(void);
#endif

#undef EXTERN
#if defined(__cplusplus)
}
#endif

#endif /* __ASSEMBLY__ */
#endif  /* __ARCH_BOARD_BOARD_H */