All lm3s6965-ek configurations converted to use kconfig-frontends

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@5470 42af7a65-404d-4744-a932-0658087f49c3

arch/arm/src/lm3s/Kconfig

@@ -12,6 +12,7 @@ choice
 
 config ARCH_CHIP_LM3S6918
 	bool "LM3S6918"
+	select LM3S_HAVE_SSI1
 
 config ARCH_CHIP_LM3S9B96
 	bool "LM3S9B96"
@@ -27,33 +28,172 @@ config ARCH_CHIP_LM3S8962
 
 endchoice
 
+config LM3S_HAVE_SSI1
+	bool
+
+config LM3S_REVA2
+	bool "Rev A2"
+	default n
+	---help---
+		Some early silicon returned an increase LDO voltage or 2.75V to work
+		around a PLL bug
+
 config LM3S_DFU
 	bool "DFU"
 	default y
 
+menu "Select LM3S Peripheral Support"
+
+config LM3S_UART0
+	bool "UART0"
+	select ARCH_HAVE_UART0
+	default n
+
+config LM3S_UART1
+	bool "UART1"
+	select ARCH_HAVE_UART1
+	default n
+
+config SSI0_DISABLE
+	bool "Disable SSI0"
+	default y
+
+config SSI1_DISABLE
+	bool "Disable SSI1"
+	default y
+
+config LM3S_UART2
+	bool "UART2"
+	select ARCH_HAVE_UART2
+	default n
+
+config LM3S_ETHERNET
+	bool "LM3S Ethernet"
+	default n
+	---help---
+		This must be set (along with NET) to build the LM3S Ethernet driver.
+
+endmenu
+
+menu "Disable GPIO Interrupts"
+
 config LM3S_DISABLE_GPIOA_IRQS
 	bool "Disable GPIOA IRQs"
+	default n
 
 config LM3S_DISABLE_GPIOB_IRQS
 	bool "Disable GPIOB IRQs"
+	default n
 
 config LM3S_DISABLE_GPIOC_IRQS
 	bool "Disable GPIOC IRQs"
+	default n
 
 config LM3S_DISABLE_GPIOD_IRQS
 	bool "Disable GPIOD IRQs"
+	default n
 
 config LM3S_DISABLE_GPIOE_IRQS
 	bool "Disable GPIOE IRQs"
+	default n
 
 config LM3S_DISABLE_GPIOF_IRQS
 	bool "Disable GPIOF IRQs"
+	default n
 
 config LM3S_DISABLE_GPIOG_IRQS
 	bool "Disable GPIOG IRQs"
+	default n
 
 config LM3S_DISABLE_GPIOH_IRQS
 	bool "Disable GPIOH IRQs"
+	default n
 
 config LM3S_DISABLE_GPIOJ_IRQS
 	bool "Disable GPIOJ IRQs"
+	default n
+
+endmenu
+
+if LM3S_ETHERNET
+menu "LM3S Ethernet Configuration"
+
+config LM3S_ETHLEDS
+	bool "Ethernet LEDs"
+	default n
+	---help---
+	Enable to use Ethernet LEDs on the board.
+
+config LM3S_BOARDMAC
+	bool "Board MAC"
+	default n
+	---help---
+		If the board-specific logic can provide a MAC address (via
+		lm3s_ethernetmac()), then this should be selected.
+
+config LM3S_ETHHDUPLEX
+	bool "Force Half Duplex"
+	default n
+	---help---
+		Set to force half duplex operation
+
+config LM3S_ETHNOAUTOCRC
+	bool "Disable auto-CRC"
+	default n
+	---help---
+		Set to suppress auto-CRC generation
+
+config LM3S_ETHNOPAD
+	bool "Disable Tx Padding"
+	default n
+	---help---
+		Set to suppress Tx padding
+
+config LM3S_MULTICAST
+	bool "Enable Multicast"
+	default n
+	---help---
+		Set to enable multicast frames
+
+config LM3S_PROMISCUOUS
+	bool "Enable Promiscuous Mode"
+	default n
+	---help---
+		Set to enable promiscuous mode
+
+config LM3S_TIMESTAMP
+	bool "Enable Timestamping"
+	default n
+
+config LM3S_BADCRC
+	bool "Enable Bad CRC Rejection"
+	default n
+	---help---
+		Set to enable bad CRC rejection.
+
+config M3S_DUMPPACKET
+	bool "Dump Packets"
+	default n
+	---help---
+		Dump each packet received/sent to the console.
+
+endmenu
+endif
+
+if !SSI0_DISABLE || !SSI1_DISABLE
+menu "LM3S SSI Configuration"
+
+config SSI_POLLWAIT
+	bool "Poll Wait (No-Interrupt) Mode"
+	default y
+
+config SSI_TXLIMIT
+	int "Tx Limit"
+	default 4
+	---help---
+		Default of 4 assumes half of the 8 entry FIFO
+
+endmenu
+endif
+
+