Add configuration for lm3s8962-ek
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@2913 42af7a65-404d-4744-a932-0658087f49c3
This commit is contained in:
patacongo
parent
1dc81d09ec
commit
11d40b9c1a
427
configs/lm3s8962-ek/README.txt
Executable file
427
configs/lm3s8962-ek/README.txt
Executable file
@ -0,0 +1,427 @@
|
||||
README
|
||||
^^^^^^
|
||||
|
||||
README for NuttX port to the Stellaris LMS38962 Evaluation Kit
|
||||
|
||||
Contents
|
||||
^^^^^^^^
|
||||
|
||||
Stellaris LMS38962 Evaluation Kit
|
||||
Development Environment
|
||||
GNU Toolchain Options
|
||||
IDEs
|
||||
NuttX buildroot Toolchain
|
||||
USB Device Controller Functions
|
||||
OLED
|
||||
Stellaris LM3S8962 Evaluation Kit Configuration Options
|
||||
Configurations
|
||||
|
||||
Stellaris LMS38962 Evaluation Kit
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
The Stellaris LM3S8962 Evaluation Board includes the following features:
|
||||
|
||||
o Stellaris LM3S8962 microcontroller with fully-integrated 10/100 embedded
|
||||
Ethernet controller
|
||||
o Simple setup; USB cable provides serial communication, debugging, and
|
||||
power
|
||||
o OLED graphics display with 128 x 96 pixel resolution
|
||||
o User LED, navigation switches, and select pushbuttons
|
||||
o Magnetic speaker
|
||||
o LM3S8962 I/O available on labeled break-out pads
|
||||
o Standard ARM® 20-pin JTAG debug connector with input and output modes
|
||||
o USB interface for debugging and power supply
|
||||
o MicroSD card slot
|
||||
|
||||
Features of the LM3S8962 Microcontroller
|
||||
|
||||
o 32-bit RISC performance using ARM® Cortex™-M3 v7M architecture
|
||||
– 50-MHz operation
|
||||
– Hardware-division and single-cycle-multiplication
|
||||
– Integrated Nested Vectored Interrupt Controller (NVIC)
|
||||
– 42 interrupt channels with eight priority levels
|
||||
o 256 KB single-cycle flash
|
||||
o 64 KB single-cycle SRAM
|
||||
o Four general-purpose 32-bit timers
|
||||
o Integrated Ethernet MAC and PHY
|
||||
o Three fully programmable 16C550-type UARTs
|
||||
o Four 10-bit channels (inputs) when used as single-ended inputs
|
||||
o Two independent integrated analog comparators
|
||||
o Two I2C modules
|
||||
o Three PWM generator blocks
|
||||
– One 16-bit counter
|
||||
– Two comparators
|
||||
– Produces two independent PWM signals
|
||||
– One dead-band generator
|
||||
o Two QEI modules with position integrator for tracking encoder position
|
||||
o 0 to 42 GPIOs, depending on user configuration
|
||||
o On-chip low drop-out (LDO) voltage regulator
|
||||
|
||||
GPIO Usage
|
||||
|
||||
PIN SIGNAL EVB Function
|
||||
--- ----------- ---------------------------------------
|
||||
26 PA0/U0RX Virtual COM port receive
|
||||
27 PA1/U0TX Virtual COM port transmit
|
||||
10 PD0/IDX0 SD card chip select
|
||||
11 PD1/PWM1 Sound
|
||||
30 PA4/SSI0RX SD card data out
|
||||
31 PA5/SSI0TX SD card and OLED display data in
|
||||
28 PA2/SSI0CLK SD card and OLED display clock
|
||||
22 PC7/PHB0 OLED display data/control select
|
||||
29 PA3/SSI0FSS OLED display chip select
|
||||
73 PE1/PWM5 Down switch
|
||||
74 PE2/PHB1 Left switch
|
||||
72 PE0/PWM4 Up switch
|
||||
75 PE3/PHA1 Right switch
|
||||
61 PF1/IDX1 Select switch
|
||||
47 PF0/PWM0 User LED
|
||||
23 PC6/CCP3 Enable +15 V
|
||||
|
||||
OLED
|
||||
^^^^
|
||||
|
||||
The Evaluation Kit includes an OLED graphics display. Features:
|
||||
|
||||
- RiT P14201 series display
|
||||
- 128 columns by 96 rows
|
||||
- 4-bit, 16-level gray scale.
|
||||
- High-contrast (typ. 500:1)
|
||||
- Excellent brightness (120 cd/m2)
|
||||
- Fast 10 us response.
|
||||
|
||||
The OLED display has a built-in controller IC with synchronous serial and
|
||||
parallel interfaces (SSD1329). Synchronous serial (SSI) is used on the EVB.
|
||||
The SSI port is shared with the microSD card slot.
|
||||
|
||||
- PC7: OLED display data/control select (D/Cn)
|
||||
- PA3: OLED display chip select (CSn)
|
||||
|
||||
NOTE: Newer versions of the LM3S8962 Evaluation Kit has an OSAM 128x64x4 OLED
|
||||
display. Some tweaks to drivers/lcd/p14201.c would be required to support that
|
||||
LCD.
|
||||
|
||||
Development Environment
|
||||
^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
Either Linux or Cygwin on Windows can be used for the development environment.
|
||||
The source has been built only using the GNU toolchain (see below). Other
|
||||
toolchains will likely cause problems. Testing was performed using the Cygwin
|
||||
environment.
|
||||
|
||||
GNU Toolchain Options
|
||||
^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
The NuttX make system has been modified to support the following different
|
||||
toolchain options.
|
||||
|
||||
1. The CodeSourcery GNU toolchain,
|
||||
2. The devkitARM GNU toolchain,
|
||||
3. The NuttX buildroot Toolchain (see below).
|
||||
|
||||
All testing has been conducted using the NuttX buildroot toolchain. However,
|
||||
the make system is setup to default to use the devkitARM toolchain. To use
|
||||
the CodeSourcery or devkitARM, you simply need to add one of the following
|
||||
configuration options to your .config (or defconfig) file:
|
||||
|
||||
CONFIG_LM3S_CODESOURCERYW=y : CodeSourcery under Windows
|
||||
CONFIG_LM3S_CODESOURCERYL=y : CodeSourcery under Linux
|
||||
CONFIG_LM3S_DEVKITARM=y : devkitARM under Windows
|
||||
CONFIG_LM3S_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
|
||||
|
||||
If you are not using CONFIG_LM3S_BUILDROOT, then you may also have to modify
|
||||
the PATH in the setenv.h file if your make cannot find the tools.
|
||||
|
||||
NOTE: the CodeSourcery (for Windows) and devkitARM are Windows native toolchains.
|
||||
The CodeSourcey (for Linux) and NuttX buildroot toolchains are Cygwin and/or Linux
|
||||
native toolchains. There are several limitations to using a Windows based
|
||||
toolchain in a Cygwin environment. The three biggest are:
|
||||
|
||||
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
||||
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
||||
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
||||
|
||||
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
||||
are used in Nuttx (e.g., include/arch). The make system works around these
|
||||
problems for the Windows tools by copying directories instead of linking them.
|
||||
But this can also cause some confusion for you: For example, you may edit
|
||||
a file in a "linked" directory and find that your changes had not effect.
|
||||
That is because you are building the copy of the file in the "fake" symbolic
|
||||
directory. If you use a Windows toolchain, you should get in the habit of
|
||||
making like this:
|
||||
|
||||
make clean_context all
|
||||
|
||||
An alias in your .bashrc file might make that less painful.
|
||||
|
||||
3. Dependencies are not made when using Windows versions of the GCC. This is
|
||||
because the dependencies are generated using Windows pathes which do not
|
||||
work with the Cygwin make.
|
||||
|
||||
Support has been added for making dependencies with the windows-native toolchains.
|
||||
That support can be enabled by modifying your Make.defs file as follows:
|
||||
|
||||
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
|
||||
|
||||
If you have problems with the dependency build (for example, if you are not
|
||||
building on C:), then you may need to modify tools/mkdeps.sh
|
||||
|
||||
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
|
||||
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
|
||||
-Os.
|
||||
|
||||
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
|
||||
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
|
||||
path or will get the wrong version of make.
|
||||
|
||||
IDEs
|
||||
^^^^
|
||||
|
||||
NuttX is built using command-line make. It can be used with an IDE, but some
|
||||
effort will be required to create the project. Here are a few tip before you
|
||||
start that effort:
|
||||
|
||||
1) Select the toolchain that you will be using in your .config file
|
||||
2) Start the NuttX build at least one time from the Cygwin command line
|
||||
before trying to create your project. This is necessary to create
|
||||
certain auto-generated files and directories that will be needed.
|
||||
3) Set up include pathes: You will need include/, arch/arm/src/lm3s,
|
||||
arch/arm/src/common, arch/arm/src/cortexm3, and sched/.
|
||||
4) All assembly files need to have the definition option -D __ASSEMBLY__
|
||||
on the command line.
|
||||
|
||||
Startup files will probably cause you some headaches. The NuttX startup file
|
||||
is arch/arm/src/lm3s/lm3s_vectors.S.
|
||||
|
||||
NuttX buildroot Toolchain
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
|
||||
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
|
||||
different from the default in your PATH variable).
|
||||
|
||||
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
|
||||
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
|
||||
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
||||
|
||||
1. You must have already configured Nuttx in <some-dir>/nuttx.
|
||||
|
||||
cd tools
|
||||
./configure.sh lm3s8962-ek/<sub-dir>
|
||||
|
||||
2. Download the latest buildroot package into <some-dir>
|
||||
|
||||
3. unpack the buildroot tarball. The resulting directory may
|
||||
have versioning information on it like buildroot-x.y.z. If so,
|
||||
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
||||
|
||||
4. cd <some-dir>/buildroot
|
||||
|
||||
5. cp configs/cortexm3-defconfig-4.3.3 .config
|
||||
|
||||
6. make oldconfig
|
||||
|
||||
7. make
|
||||
|
||||
8. Edit setenv.h, if necessary, so that the PATH variable includes
|
||||
the path to the newly built binaries.
|
||||
|
||||
See the file configs/README.txt in the buildroot source tree. That has more
|
||||
detailed PLUS some special instructions that you will need to follow if you
|
||||
are building a Cortex-M3 toolchain for Cygwin under Windows.
|
||||
|
||||
NOTE: This is an OABI toolchain.
|
||||
|
||||
USB Device Controller Functions
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
Device Overview
|
||||
|
||||
An FT2232 device from Future Technology Devices International Ltd manages
|
||||
USB-to-serial conversion. The FT2232 is factory configured by Luminary
|
||||
Micro to implement a JTAG/SWD port (synchronous serial) on channel A and
|
||||
a Virtual COM Port (VCP) on channel B. This feature allows two simultaneous
|
||||
communications links between the host computer and the target device using
|
||||
a single USB cable. Separate Windows drivers for each function are provided
|
||||
on the Documentation and Software CD.
|
||||
|
||||
Debugging with JTAG/SWD
|
||||
|
||||
The FT2232 USB device performs JTAG/SWD serial operations under the control
|
||||
of the debugger or the Luminary Flash Programmer. It also operate as an
|
||||
In-Circuit Debugger Interface (ICDI), allowing debugging of any external
|
||||
target board. Debugging modes:
|
||||
|
||||
MODE DEBUG FUNCTION USE SELECTED BY
|
||||
1 Internal ICDI Debug on-board LM3S8962 Default Mode
|
||||
microcontroller over USB
|
||||
interface.
|
||||
2 ICDI out to JTAG/SWD The EVB is used as a USB Connecting to an external
|
||||
header to SWD/JTAG interface to target and starting debug
|
||||
an external target. software. The red Debug Out
|
||||
LED will be ON.
|
||||
3 In from JTAG/SWD For users who prefer an Connecting an external
|
||||
header external debug interface debugger to the JTAG/SWD
|
||||
(ULINK, JLINK, etc.) with header.
|
||||
the EVB.
|
||||
|
||||
Virtual COM Port
|
||||
|
||||
The Virtual COM Port (VCP) allows Windows applications (such as HyperTerminal)
|
||||
to communicate with UART0 on the LM3S8962 over USB. Once the FT2232 VCP
|
||||
driver is installed, Windows assigns a COM port number to the VCP channel.
|
||||
|
||||
Stellaris LM3S8962 Evaluation Kit Configuration Options
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
||||
be set to:
|
||||
|
||||
CONFIG_ARCH=arm
|
||||
|
||||
CONFIG_ARCH_family - For use in C code:
|
||||
|
||||
CONFIG_ARCH_ARM=y
|
||||
|
||||
CONFIG_ARCH_architecture - For use in C code:
|
||||
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
|
||||
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
|
||||
CONFIG_ARCH_CHIP=lm3s
|
||||
|
||||
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
||||
chip:
|
||||
|
||||
CONFIG_ARCH_CHIP_LM3S8962
|
||||
|
||||
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
||||
hence, the board that supports the particular chip or SoC.
|
||||
|
||||
CONFIG_ARCH_BOARD=lm3s8962-ek (for the Stellaris LM3S8962 Evaluation Kit)
|
||||
|
||||
CONFIG_ARCH_BOARD_name - For use in C code
|
||||
|
||||
CONFIG_ARCH_BOARD_LM3S8962EK
|
||||
|
||||
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
||||
of delay loops
|
||||
|
||||
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
||||
endian)
|
||||
|
||||
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
||||
|
||||
CONFIG_DRAM_SIZE=0x00010000 (64Kb)
|
||||
|
||||
CONFIG_DRAM_START - The start address of installed DRAM
|
||||
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
|
||||
CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
|
||||
CONFIG_ARCH_IRQPRIO - The LM3S6918 supports interrupt prioritization
|
||||
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
|
||||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
||||
have LEDs
|
||||
|
||||
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
stack. If defined, this symbol is the size of the interrupt
|
||||
stack in bytes. If not defined, the user task stacks will be
|
||||
used during interrupt handling.
|
||||
|
||||
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
|
||||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
|
||||
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
cause a 100 second delay during boot-up. This 100 second delay
|
||||
serves no purpose other than it allows you to calibratre
|
||||
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
||||
the delay actually is 100 seconds.
|
||||
|
||||
There are configurations for disabling support for interrupts GPIO ports.
|
||||
GPIOJ must be disabled because it does not exist on the LM3S6918.
|
||||
Additional interrupt support can be disabled if desired to reduce memory
|
||||
footprint.
|
||||
|
||||
CONFIG_LM3S_DISABLE_GPIOA_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOB_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOC_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOD_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOE_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOF_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOG_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOH_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y
|
||||
|
||||
LM3S6818 specific device driver settings
|
||||
|
||||
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||||
console and ttys0 (default is the UART0).
|
||||
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
This specific the size of the receive buffer
|
||||
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||||
being sent. This specific the size of the transmit buffer
|
||||
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
CONFIG_UARTn_2STOP - Two stop bits
|
||||
|
||||
CONFIG_SSI0_DISABLE - Select to disable support for SSI0
|
||||
CONFIG_SSI1_DISABLE - Select to disable support for SSI1
|
||||
CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support.
|
||||
Poll-waiting is recommended if the interrupt rate would be to
|
||||
high in the interrupt driven case.
|
||||
CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
value is large, then larger values of this setting may cause
|
||||
Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
|
||||
CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET)
|
||||
to build the LM3S Ethernet driver
|
||||
CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
||||
CONFIG_LM3S_BOARDMAC - If the board-specific logic can provide
|
||||
a MAC address (via lm3s_ethernetmac()), then this should be selected.
|
||||
CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation
|
||||
CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
||||
CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding
|
||||
CONFIG_LM3S_MULTICAST - Set to enable multicast frames
|
||||
CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode
|
||||
CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection.
|
||||
CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console.
|
||||
|
||||
Configurations
|
||||
^^^^^^^^^^^^^^
|
||||
|
||||
Each Stellaris LM3S8962 Evaluation Kit configuration is maintained in a
|
||||
sudirectory and can be selected as follow:
|
||||
|
||||
cd tools
|
||||
./configure.sh lm3s8962-ek/<subdir>
|
||||
cd -
|
||||
. ./setenv.sh
|
||||
|
||||
Where <subdir> is one of the following:
|
||||
|
||||
nsh:
|
||||
Configures the NuttShell (nsh) located at examples/nsh. The
|
||||
Configuration enables both the serial and telnetd NSH interfaces.
|
||||
|
||||
NOTE: As it is configured now, you MUST have a network connected.
|
||||
Otherwise, the NSH prompt will not come up because the Ethernet
|
||||
driver is waiting for the network to come up. That is probably
|
||||
a bug in the Ethernet driver behavior!
|
||||
|
||||
ostest:
|
||||
This configuration directory, performs a simple OS test using
|
||||
examples/ostest.
|
||||
|
||||
|
||||
1
configs/lm3s8962-ek/include/README.txt
Executable file
1
configs/lm3s8962-ek/include/README.txt
Executable file
@ -0,0 +1 @@
|
||||
This directory contains header files unique to the Stellaris LM3S8962 Evaluation Kit.
|
||||
142
configs/lm3s8962-ek/include/board.h
Executable file
142
configs/lm3s8962-ek/include/board.h
Executable file
@ -0,0 +1,142 @@
|
||||
/************************************************************************************
|
||||
* configs/lm3s8962-ek/include/board.h
|
||||
* include/arch/board/board.h
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __ARCH_BOARD_BOARD_H
|
||||
#define __ARCH_BOARD_BOARD_H
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/* Clocking *************************************************************************/
|
||||
|
||||
/* RCC settings */
|
||||
|
||||
#define SYSCON_RCC_XTAL SYSCON_RCC_XTAL8000KHZ /* Eagle100 on-board crystall is 8.00 MHz */
|
||||
#define XTAL_FREQUENCY 8000000
|
||||
|
||||
/* Oscillator source is the main oscillator (not internal, internal/4, 30KHz or
|
||||
* 30KHz from hibernate module) */
|
||||
|
||||
#define SYSCON_RCC_OSCSRC SYSCON_RCC_OSCSRC_MOSC
|
||||
#define SYSCON_RCC2_OSCSRC SYSCON_RCC2_OSCSRC2_MOSC
|
||||
#define OSCSRC_FREQUENCY XTAL_FREQUENCY
|
||||
|
||||
/* Use system divider = 4; this corresponds to a system clock frequency
|
||||
* of (400 / 2) / 4 = 50MHz
|
||||
*/
|
||||
|
||||
#define LM3S_SYSDIV 4
|
||||
#define SYSCLK_FREQUENCY 50000000 /* 50MHz */
|
||||
|
||||
/* Other RCC settings:
|
||||
*
|
||||
* - Main and internal oscillators enabled.
|
||||
* - PLL and sys dividers not bypassed
|
||||
* - PLL not powered down
|
||||
* - No auto-clock gating reset
|
||||
*/
|
||||
|
||||
#define LM3S_RCC_VALUE (SYSCON_RCC_OSCSRC | SYSCON_RCC_XTAL | SYSCON_RCC_USESYSDIV | SYSCON_RCC_SYSDIV(LM3S_SYSDIV))
|
||||
|
||||
/* RCC2 settings -- RCC2 not used. Other RCC2 settings
|
||||
*
|
||||
* - PLL and sys dividers not bypassed.
|
||||
* - PLL not powered down
|
||||
* - Not using RCC2
|
||||
*/
|
||||
|
||||
#define LM3S_RCC2_VALUE (SYSCON_RCC2_OSCSRC | SYSCON_RCC2_SYSDIV(LM3S_SYSDIV))
|
||||
|
||||
/* LED definitions ******************************************************************/
|
||||
|
||||
/* The LMS38962 Eval Kit has only one user LED: Port F, Bit 0. Below is the mapping of this
|
||||
* single LED. From this single LED, we can get the following information:
|
||||
*
|
||||
* OFF Steady: The system has failed to boot to the point of enabling interrupts
|
||||
* ON Steady: The systems has enabled interrupts, but none have been received
|
||||
* Dull glow: The system is taking interrupts
|
||||
* Slow blinking: The system has panicked
|
||||
*/
|
||||
/* ON OFF */
|
||||
#define LED_STARTED 0 /* OFF OFF */
|
||||
#define LED_HEAPALLOCATE 1 /* OFF OFF */
|
||||
#define LED_IRQSENABLED 2 /* ON ON */
|
||||
#define LED_STACKCREATED 3 /* ON ON */
|
||||
#define LED_INIRQ 4 /* ON OFF */
|
||||
#define LED_SIGNAL 5 /* ON OFF */
|
||||
#define LED_ASSERTION 6 /* ON OFF */
|
||||
#define LED_PANIC 7 /* ON OFF */
|
||||
|
||||
/************************************************************************************
|
||||
* Public Function Prototypes
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
/************************************************************************************
|
||||
* Name: lm3s_boardinitialize
|
||||
*
|
||||
* Description:
|
||||
* All LM3S architectures must provide the following entry point. This entry point
|
||||
* is called early in the intitialization -- after all memory has been configured
|
||||
* and mapped but before any devices have been initialized.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
extern void lm3s_boardinitialize(void);
|
||||
|
||||
/************************************************************************************
|
||||
* Name: lm3s_ethernetmac
|
||||
*
|
||||
* Description:
|
||||
* For the Ethernet Eval Kits, the MAC address will be stored in the non-volatile
|
||||
* USER0 and USER1 registers. If CONFIG_LM3S_BOARDMAC is defined, this function
|
||||
* will obtain the MAC address from these registers.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifdef CONFIG_LM3S_BOARDMAC
|
||||
struct ether_addr;
|
||||
extern void lm3s_ethernetmac(struct ether_addr *ethaddr);
|
||||
#endif
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
#endif /* __ARCH_BOARD_BOARD_H */
|
||||
162
configs/lm3s8962-ek/nsh/Make.defs
Executable file
162
configs/lm3s8962-ek/nsh/Make.defs
Executable file
@ -0,0 +1,162 @@
|
||||
############################################################################
|
||||
# configs/lm3s8962-ek/nsh/Make.defs
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_LM3S_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/ld.script}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/ld.script
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
||||
622
configs/lm3s8962-ek/nsh/defconfig
Executable file
622
configs/lm3s8962-ek/nsh/defconfig
Executable file
@ -0,0 +1,622 @@
|
||||
############################################################################
|
||||
# configs/lm3s8962-ek/nsh/defconfig
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
# CONFIG_ARCH_IRQPRIO - The LM3S8962 supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibratre
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
#
|
||||
CONFIG_ARCH=arm
|
||||
CONFIG_ARCH_ARM=y
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
CONFIG_ARCH_CHIP=lm3s
|
||||
CONFIG_ARCH_CHIP_LM3S8962=y
|
||||
CONFIG_ARCH_BOARD=lm3s8962-ek
|
||||
CONFIG_ARCH_BOARD_LM3S8962EK=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=4531
|
||||
CONFIG_DRAM_SIZE=0x00010000
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=n
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_CALIBRATION=n
|
||||
|
||||
#
|
||||
# Identify toolchain and linker options
|
||||
#
|
||||
CONFIG_LM3S_CODESOURCERYW=n
|
||||
CONFIG_LM3S_CODESOURCERYL=n
|
||||
CONFIG_LM3S_DEVKITARM=n
|
||||
CONFIG_LM3S_BUILDROOT=y
|
||||
CONFIG_LM3S_DFU=y
|
||||
|
||||
#
|
||||
# Disable support for interrupts on GPIOH and GPIOJ which do not
|
||||
# exist on the LM3S6B96. Additional interrupt support can be
|
||||
# disabled if desired to reduce memory footprint.
|
||||
CONFIG_LM3S_DISABLE_GPIOA_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOB_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOC_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOD_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOE_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOF_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOG_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOH_IRQS=y
|
||||
CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y
|
||||
|
||||
#
|
||||
# LM3S8962 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_UARTn_DISABLE - select to disable all support for
|
||||
# the UART
|
||||
# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||||
# console and ttys0 (default is the UART0).
|
||||
# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_UARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_UART0_DISABLE=n
|
||||
CONFIG_UART1_DISABLE=y
|
||||
CONFIG_UART2_DISABLE=y
|
||||
CONFIG_UART0_SERIAL_CONSOLE=y
|
||||
CONFIG_UART1_SERIAL_CONSOLE=n
|
||||
CONFIG_UART2_SERIAL_CONSOLE=n
|
||||
CONFIG_UART0_TXBUFSIZE=256
|
||||
CONFIG_UART1_TXBUFSIZE=256
|
||||
CONFIG_UART2_TXBUFSIZE=256
|
||||
CONFIG_UART0_RXBUFSIZE=256
|
||||
CONFIG_UART1_RXBUFSIZE=256
|
||||
CONFIG_UART2_RXBUFSIZE=256
|
||||
CONFIG_UART0_BAUD=115200
|
||||
CONFIG_UART1_BAUD=115200
|
||||
CONFIG_UART2_BAUD=115200
|
||||
CONFIG_UART0_BITS=8
|
||||
CONFIG_UART1_BITS=8
|
||||
CONFIG_UART2_BITS=8
|
||||
CONFIG_UART0_PARITY=0
|
||||
CONFIG_UART1_PARITY=0
|
||||
CONFIG_UART2_PARITY=0
|
||||
CONFIG_UART0_2STOP=0
|
||||
CONFIG_UART1_2STOP=0
|
||||
CONFIG_UART2_2STOP=0
|
||||
|
||||
#
|
||||
# LM3S8962 specific SSI device driver settings
|
||||
#
|
||||
# CONFIG_SSIn_DISABLE - select to disable all support for
|
||||
# the SSI
|
||||
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
|
||||
# Poll-waiting is recommended if the interrupt rate would be to
|
||||
# high in the interrupt driven case.
|
||||
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
# emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
# value is large, then larger values of this setting may cause
|
||||
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
#
|
||||
CONFIG_SSI0_DISABLE=n
|
||||
CONFIG_SSI1_DISABLE=y
|
||||
CONFIG_SSI_POLLWAIT=y
|
||||
#CONFIG_SSI_TXLIMIT=4
|
||||
|
||||
#
|
||||
# LM3S8962 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET)
|
||||
# to build the LM3S Ethernet driver
|
||||
# CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
||||
# CONFIG_LM3S_BOARDMAC - If the board-specific logic can provide
|
||||
# a MAC address (via lm3s_ethernetmac()), then this should be selected.
|
||||
# CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation
|
||||
# CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
||||
# CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding
|
||||
# CONFIG_LM3S_MULTICAST - Set to enable multicast frames
|
||||
# CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode
|
||||
# CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection.
|
||||
# CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console.
|
||||
#
|
||||
CONFIG_LM3S_ETHERNET=y
|
||||
CONFIG_LM3S_ETHLEDS=n
|
||||
CONFIG_LM3S_BOARDMAC=n
|
||||
CONFIG_LM3S_ETHHDUPLEX=n
|
||||
CONFIG_LM3S_ETHNOAUTOCRC=n
|
||||
CONFIG_LM3S_ETHNOPAD=n
|
||||
CONFIG_LM3S_MULTICAST=n
|
||||
CONFIG_LM3S_PROMISCUOUS=n
|
||||
CONFIG_LM3S_BADCRC=n
|
||||
CONFIG_LM3S_DUMPPACKET=n
|
||||
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=n
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
CONFIG_RAW_BINARY=y
|
||||
CONFIG_HAVE_LIBM=n
|
||||
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APP_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX.
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_TICKS_PER_MSEC - The default system timer is 100Hz
|
||||
# or TICKS_PER_MSEC=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
||||
# You would only need this if you are concerned about accurate
|
||||
# time conversions in the past or in the distant future.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
||||
# would only need this if you are concerned about accurate
|
||||
# time conversion in the distand past. You must also define
|
||||
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
#
|
||||
CONFIG_APP_DIR=examples/nsh
|
||||
CONFIG_DEBUG=n
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_DEBUG_NET=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2010
|
||||
CONFIG_START_MONTH=5
|
||||
CONFIG_START_DAY=8
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
CONFIG_DEV_LOWCONSOLE=n
|
||||
CONFIG_MUTEX_TYPES=n
|
||||
CONFIG_PRIORITY_INHERITANCE=n
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SEM_NNESTPRIO=0
|
||||
CONFIG_FDCLONE_DISABLE=n
|
||||
CONFIG_FDCLONE_STDIO=n
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_NXFLAT=n
|
||||
|
||||
#
|
||||
# The following can be used to disable categories of
|
||||
# APIs supported by the OS. If the compiler supports
|
||||
# weak functions, then it should not be necessary to
|
||||
# disable functions unless you want to restrict usage
|
||||
# of those APIs.
|
||||
#
|
||||
# There are certain dependency relationships in these
|
||||
# features.
|
||||
#
|
||||
# o mq_notify logic depends on signals to awaken tasks
|
||||
# waiting for queues to become full or empty.
|
||||
# o pthread_condtimedwait() depends on signals to wake
|
||||
# up waiting tasks.
|
||||
#
|
||||
CONFIG_DISABLE_CLOCK=n
|
||||
CONFIG_DISABLE_POSIX_TIMERS=n
|
||||
CONFIG_DISABLE_PTHREAD=n
|
||||
CONFIG_DISABLE_SIGNALS=n
|
||||
CONFIG_DISABLE_MQUEUE=n
|
||||
CONFIG_DISABLE_MOUNTPOINT=n
|
||||
CONFIG_DISABLE_ENVIRON=n
|
||||
CONFIG_DISABLE_POLL=y
|
||||
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
# Allow for architecture optimized implementations
|
||||
#
|
||||
# The architecture can provide optimized versions of the
|
||||
# following to improve system performance
|
||||
#
|
||||
CONFIG_ARCH_MEMCPY=n
|
||||
CONFIG_ARCH_MEMCMP=n
|
||||
CONFIG_ARCH_MEMMOVE=n
|
||||
CONFIG_ARCH_MEMSET=n
|
||||
CONFIG_ARCH_STRCMP=n
|
||||
CONFIG_ARCH_STRCPY=n
|
||||
CONFIG_ARCH_STRNCPY=n
|
||||
CONFIG_ARCH_STRLEN=n
|
||||
CONFIG_ARCH_BZERO=n
|
||||
CONFIG_ARCH_KMALLOC=n
|
||||
CONFIG_ARCH_KZMALLOC=n
|
||||
CONFIG_ARCH_KFREE=n
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=16
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=8
|
||||
CONFIG_NFILE_STREAMS=8
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_STDIO_BUFFER_SIZE=256
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
CONFIG_FS_FAT=y
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_LLH_LEN - The link level header length
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=y
|
||||
CONFIG_NET_IPv6=n
|
||||
CONFIG_NSOCKET_DESCRIPTORS=8
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=562
|
||||
CONFIG_NET_TCP=y
|
||||
CONFIG_NET_TCP_CONNS=8
|
||||
CONFIG_NET_NTCP_READAHEAD_BUFFERS=16
|
||||
CONFIG_NET_TCPBACKLOG=n
|
||||
CONFIG_NET_MAX_LISTENPORTS=8
|
||||
CONFIG_NET_UDP=y
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
#CONFIG_NET_UDP_CONNS=8
|
||||
CONFIG_NET_ICMP=y
|
||||
CONFIG_NET_ICMP_PING=y
|
||||
#CONFIG_NET_PINGADDRCONF=0
|
||||
CONFIG_NET_STATISTICS=y
|
||||
#CONFIG_NET_RECEIVE_WINDOW=
|
||||
#CONFIG_NET_ARPTAB_SIZE=8
|
||||
CONFIG_NET_BROADCAST=n
|
||||
#CONFIG_NET_LLH_LEN=14
|
||||
#CONFIG_NET_FWCACHE_SIZE=2
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
|
||||
#
|
||||
# Settings for examples/uip
|
||||
#
|
||||
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
|
||||
#
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
# Settings for examples/nsh
|
||||
#
|
||||
# CONFIG_EXAMPLES_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_EXAMPLES_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_EXAMPLES_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_EXAMPLES_NSH_STACKSIZE - Stack size to use for new threads.
|
||||
# CONFIG_EXAMPLES_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_EXAMPLES_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_EXAMPLES_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_EXAMPLES_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_EXAMPLES_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_EXAMPLES_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_EXAMPLES_NSH_TELNET is selected:
|
||||
# CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_EXAMPLES_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_EXAMPLES_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_EXAMPLES_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_EXAMPLES_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_EXAMPLES_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_EXAMPLES_NSH_ROMFSETC is selected:
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_EXAMPLES_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_EXAMPLES_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_EXAMPLES_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_EXAMPLES_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_EXAMPLES_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_EXAMPLES_NSH_FILEIOSIZE=512
|
||||
CONFIG_EXAMPLES_NSH_STRERROR=n
|
||||
CONFIG_EXAMPLES_NSH_LINELEN=64
|
||||
CONFIG_EXAMPLES_NSH_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_NSH_NESTDEPTH=3
|
||||
CONFIG_EXAMPLES_NSH_DISABLESCRIPT=n
|
||||
CONFIG_EXAMPLES_NSH_DISABLEBG=n
|
||||
CONFIG_EXAMPLES_NSH_ROMFSETC=n
|
||||
CONFIG_EXAMPLES_NSH_CONSOLE=y
|
||||
CONFIG_EXAMPLES_NSH_TELNET=y
|
||||
CONFIG_EXAMPLES_NSH_ARCHINIT=y
|
||||
CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE=512
|
||||
CONFIG_EXAMPLES_NSH_DHCPC=n
|
||||
CONFIG_EXAMPLES_NSH_NOMAC=y
|
||||
CONFIG_EXAMPLES_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLES_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLES_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT="/etc"
|
||||
CONFIG_EXAMPLES_NSH_INITSCRIPT="init.d/rcS"
|
||||
CONFIG_EXAMPLES_NSH_ROMFSDEVNO=0
|
||||
CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE=64
|
||||
CONFIG_EXAMPLES_NSH_FATDEVNO=1
|
||||
CONFIG_EXAMPLES_NSH_FATSECTSIZE=512
|
||||
CONFIG_EXAMPLES_NSH_FATNSECTORS=1024
|
||||
CONFIG_EXAMPLES_NSH_FATMOUNTPT=/tmp
|
||||
|
||||
#
|
||||
# Architecture-specific NSH options
|
||||
#
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO=0
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSLOTNO=0
|
||||
CONFIG_EXAMPLES_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should also be =n for the LM3S8962 Eval Kit which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=n
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
CONFIG_STACK_POINTER=
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
CONFIG_HEAP_BASE=
|
||||
CONFIG_HEAP_SIZE=
|
||||
108
configs/lm3s8962-ek/nsh/ld.script
Executable file
108
configs/lm3s8962-ek/nsh/ld.script
Executable file
@ -0,0 +1,108 @@
|
||||
/****************************************************************************
|
||||
* configs/lm3s8962-ek/nsh/ld.script
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The LM3S8962 has 256Kb of FLASH beginning at address 0x0000:0000 and 64Kb
|
||||
* of SRAM beginning at 0x2000:0000.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x00000000, LENGTH = 256K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.); /* See below */
|
||||
|
||||
/* The LM3S6918 has 64Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
.ARM.exidx : {
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
*(.ARM.exidx*)
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
} >sram
|
||||
|
||||
.bss : { /* BSS */
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
||||
46
configs/lm3s8962-ek/nsh/setenv.sh
Executable file
46
configs/lm3s8962-ek/nsh/setenv.sh
Executable file
@ -0,0 +1,46 @@
|
||||
#!/bin/bash
|
||||
# configs/lm3s8962-ek/nsh/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$(basename $0)" = "setenv.sh" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
|
||||
|
||||
WD=`pwd`
|
||||
export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
export PATH="${BUILDROOT_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
||||
162
configs/lm3s8962-ek/nx/Make.defs
Executable file
162
configs/lm3s8962-ek/nx/Make.defs
Executable file
@ -0,0 +1,162 @@
|
||||
############################################################################
|
||||
# configs/lm3s8962-ek/nx/Make.defs
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_LM3S_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nx/ld.script}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nx/ld.script
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
||||
779
configs/lm3s8962-ek/nx/defconfig
Executable file
779
configs/lm3s8962-ek/nx/defconfig
Executable file
@ -0,0 +1,779 @@
|
||||
############################################################################
|
||||
# configs/lm3s8962-ek/nx/defconfig
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
# CONFIG_ARCH_IRQPRIO - The LM3S8962 supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibratre
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
#
|
||||
CONFIG_ARCH=arm
|
||||
CONFIG_ARCH_ARM=y
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
CONFIG_ARCH_CHIP=lm3s
|
||||
CONFIG_ARCH_CHIP_LM3S8962=y
|
||||
CONFIG_ARCH_BOARD=lm3s8962-ek
|
||||
CONFIG_ARCH_BOARD_LM3S8962EK=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=4531
|
||||
CONFIG_DRAM_SIZE=0x00010000
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=n
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_CALIBRATION=n
|
||||
|
||||
#
|
||||
# Identify toolchain and linker options
|
||||
#
|
||||
CONFIG_LM3S_CODESOURCERYW=n
|
||||
CONFIG_LM3S_CODESOURCERYL=n
|
||||
CONFIG_LM3S_DEVKITARM=n
|
||||
CONFIG_LM3S_BUILDROOT=y
|
||||
CONFIG_LM3S_DFU=y
|
||||
|
||||
#
|
||||
# Disable support for interrupts on GPIOH and GPIOJ which do not
|
||||
# exist on the LM3S6B96. Additional interrupt support can be
|
||||
# disabled if desired to reduce memory footprint.
|
||||
CONFIG_LM3S_DISABLE_GPIOA_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOB_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOC_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOD_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOE_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOF_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOG_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOH_IRQS=y
|
||||
CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y
|
||||
|
||||
#
|
||||
# LM3S8962 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_UARTn_DISABLE - select to disable all support for
|
||||
# the UART
|
||||
# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||||
# console and ttys0 (default is the UART0).
|
||||
# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_UARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_UART0_DISABLE=n
|
||||
CONFIG_UART1_DISABLE=y
|
||||
CONFIG_UART2_DISABLE=y
|
||||
CONFIG_UART0_SERIAL_CONSOLE=y
|
||||
CONFIG_UART1_SERIAL_CONSOLE=n
|
||||
CONFIG_UART2_SERIAL_CONSOLE=n
|
||||
CONFIG_UART0_TXBUFSIZE=256
|
||||
CONFIG_UART1_TXBUFSIZE=256
|
||||
CONFIG_UART2_TXBUFSIZE=256
|
||||
CONFIG_UART0_RXBUFSIZE=256
|
||||
CONFIG_UART1_RXBUFSIZE=256
|
||||
CONFIG_UART2_RXBUFSIZE=256
|
||||
CONFIG_UART0_BAUD=115200
|
||||
CONFIG_UART1_BAUD=115200
|
||||
CONFIG_UART2_BAUD=115200
|
||||
CONFIG_UART0_BITS=8
|
||||
CONFIG_UART1_BITS=8
|
||||
CONFIG_UART2_BITS=8
|
||||
CONFIG_UART0_PARITY=0
|
||||
CONFIG_UART1_PARITY=0
|
||||
CONFIG_UART2_PARITY=0
|
||||
CONFIG_UART0_2STOP=0
|
||||
CONFIG_UART1_2STOP=0
|
||||
CONFIG_UART2_2STOP=0
|
||||
|
||||
#
|
||||
# LM3S8962 specific SSI device driver settings
|
||||
#
|
||||
# CONFIG_SSIn_DISABLE - select to disable all support for
|
||||
# the SSI
|
||||
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
|
||||
# Poll-waiting is recommended if the interrupt rate would be to
|
||||
# high in the interrupt driven case.
|
||||
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
# emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
# value is large, then larger values of this setting may cause
|
||||
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
#
|
||||
CONFIG_SSI0_DISABLE=n
|
||||
CONFIG_SSI1_DISABLE=y
|
||||
CONFIG_SSI_POLLWAIT=y
|
||||
#CONFIG_SSI_TXLIMIT=4
|
||||
|
||||
#
|
||||
# LM3S8962 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET)
|
||||
# to build the LM3S Ethernet driver
|
||||
# CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
||||
# CONFIG_LM3S_BOARDMAC - If the board-specific logic can provide
|
||||
# a MAC address (via lm3s_ethernetmac()), then this should be selected.
|
||||
# CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation
|
||||
# CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
||||
# CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding
|
||||
# CONFIG_LM3S_MULTICAST - Set to enable multicast frames
|
||||
# CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode
|
||||
# CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection.
|
||||
# CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console.
|
||||
#
|
||||
CONFIG_LM3S_ETHERNET=n
|
||||
CONFIG_LM3S_ETHLEDS=n
|
||||
CONFIG_LM3S_BOARDMAC=y
|
||||
CONFIG_LM3S_ETHHDUPLEX=n
|
||||
CONFIG_LM3S_ETHNOAUTOCRC=n
|
||||
CONFIG_LM3S_ETHNOPAD=n
|
||||
CONFIG_LM3S_MULTICAST=n
|
||||
CONFIG_LM3S_PROMISCUOUS=n
|
||||
CONFIG_LM3S_BADCRC=n
|
||||
CONFIG_LM3S_DUMPPACKET=n
|
||||
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=n
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
CONFIG_RAW_BINARY=y
|
||||
CONFIG_HAVE_LIBM=n
|
||||
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APP_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX.
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_TICKS_PER_MSEC - The default system timer is 100Hz
|
||||
# or TICKS_PER_MSEC=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
||||
# You would only need this if you are concerned about accurate
|
||||
# time conversions in the past or in the distant future.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
||||
# would only need this if you are concerned about accurate
|
||||
# time conversion in the distand past. You must also define
|
||||
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
#
|
||||
CONFIG_APP_DIR=examples/nx
|
||||
CONFIG_DEBUG=n
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_DEBUG_GRAPHICS=n
|
||||
CONFIG_LCD_RITDEBUG=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2010
|
||||
CONFIG_START_MONTH=5
|
||||
CONFIG_START_DAY=12
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
CONFIG_DEV_LOWCONSOLE=n
|
||||
CONFIG_MUTEX_TYPES=n
|
||||
CONFIG_PRIORITY_INHERITANCE=n
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SEM_NNESTPRIO=0
|
||||
CONFIG_FDCLONE_DISABLE=n
|
||||
CONFIG_FDCLONE_STDIO=n
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_NXFLAT=n
|
||||
|
||||
#
|
||||
# The following can be used to disable categories of
|
||||
# APIs supported by the OS. If the compiler supports
|
||||
# weak functions, then it should not be necessary to
|
||||
# disable functions unless you want to restrict usage
|
||||
# of those APIs.
|
||||
#
|
||||
# There are certain dependency relationships in these
|
||||
# features.
|
||||
#
|
||||
# o mq_notify logic depends on signals to awaken tasks
|
||||
# waiting for queues to become full or empty.
|
||||
# o pthread_condtimedwait() depends on signals to wake
|
||||
# up waiting tasks.
|
||||
#
|
||||
CONFIG_DISABLE_CLOCK=n
|
||||
CONFIG_DISABLE_POSIX_TIMERS=y
|
||||
CONFIG_DISABLE_PTHREAD=n
|
||||
CONFIG_DISABLE_SIGNALS=n
|
||||
CONFIG_DISABLE_MQUEUE=n
|
||||
CONFIG_DISABLE_MOUNTPOINT=y
|
||||
CONFIG_DISABLE_ENVIRON=y
|
||||
CONFIG_DISABLE_POLL=y
|
||||
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
# Allow for architecture optimized implementations
|
||||
#
|
||||
# The architecture can provide optimized versions of the
|
||||
# following to improve system performance
|
||||
#
|
||||
CONFIG_ARCH_MEMCPY=n
|
||||
CONFIG_ARCH_MEMCMP=n
|
||||
CONFIG_ARCH_MEMMOVE=n
|
||||
CONFIG_ARCH_MEMSET=n
|
||||
CONFIG_ARCH_STRCMP=n
|
||||
CONFIG_ARCH_STRCPY=n
|
||||
CONFIG_ARCH_STRNCPY=n
|
||||
CONFIG_ARCH_STRLEN=n
|
||||
CONFIG_ARCH_BZERO=n
|
||||
CONFIG_ARCH_KMALLOC=n
|
||||
CONFIG_ARCH_KZMALLOC=n
|
||||
CONFIG_ARCH_KFREE=n
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=16
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=12
|
||||
CONFIG_NFILE_STREAMS=12
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_STDIO_BUFFER_SIZE=256
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Framebuffer driver options
|
||||
CONFIG_FB_CMAP=n
|
||||
CONFIG_FB_HWCURSOR=n
|
||||
CONFIG_FB_HWCURSORIMAGE=n
|
||||
#CONFIG_FB_HWCURSORSIZE
|
||||
#CONFIG_FB_TRANSPARENCY
|
||||
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
CONFIG_FS_FAT=n
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_LLH_LEN - The link level header length
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=n
|
||||
CONFIG_NET_IPv6=n
|
||||
CONFIG_NSOCKET_DESCRIPTORS=0
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=420
|
||||
CONFIG_NET_TCP=n
|
||||
CONFIG_NET_TCP_CONNS=40
|
||||
CONFIG_NET_MAX_LISTENPORTS=40
|
||||
CONFIG_NET_UDP=n
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
#CONFIG_NET_UDP_CONNS=10
|
||||
CONFIG_NET_ICMP=n
|
||||
CONFIG_NET_ICMP_PING=n
|
||||
#CONFIG_NET_PINGADDRCONF=0
|
||||
CONFIG_NET_STATISTICS=y
|
||||
#CONFIG_NET_RECEIVE_WINDOW=
|
||||
#CONFIG_NET_ARPTAB_SIZE=8
|
||||
CONFIG_NET_BROADCAST=n
|
||||
#CONFIG_NET_LLH_LEN=14
|
||||
#CONFIG_NET_FWCACHE_SIZE=2
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
|
||||
#
|
||||
# Graphics related configuration settings
|
||||
#
|
||||
# CONFIG_NX
|
||||
# Enables overall support for graphics library and NX
|
||||
# CONFIG_NX_MULTIUSER
|
||||
# Configures NX in multi-user mode
|
||||
# CONFIG_NX_NPLANES
|
||||
# Some YUV color formats requires support for multiple planes,
|
||||
# one for each color component. Unless you have such special
|
||||
# hardware, this value should be undefined or set to 1
|
||||
# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
|
||||
# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
|
||||
# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
|
||||
# CONFIG_NX_DISABLE_32BPP
|
||||
# NX supports a variety of pixel depths. You can save some
|
||||
# memory by disabling support for unused color depths.
|
||||
# CONFIG_NX_PACKEDMSFIRST
|
||||
# If a pixel depth of less than 8-bits is used, then NX needs
|
||||
# to know if the pixels pack from the MS to LS or from LS to MS
|
||||
# CONFIG_NX_LCDDRIVER
|
||||
# By default, NX builds to use a framebuffer driver (see
|
||||
# include/nuttx/fb.h). If this option is defined, NX will
|
||||
# build to use an LCD driver (see include/nuttx/lcd.h).
|
||||
# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
|
||||
# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
|
||||
# CONFIG_NX_MOUSE
|
||||
# Build in support for mouse input
|
||||
# CONFIG_NX_KBD
|
||||
# Build in support of keypad/keyboard input
|
||||
# CONFIG_NXTK_BORDERWIDTH
|
||||
# Specifies with with of the border (in pixels) used with
|
||||
# framed windows. The default is 4.
|
||||
# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
|
||||
# Specify the colors of the border used with framed windows.
|
||||
# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
|
||||
# is normally darker. The default is medium and dark grey,
|
||||
# respectively
|
||||
# CONFIG_NXTK_AUTORAISE
|
||||
# If set, a window will be raised to the top if the mouse position
|
||||
# is over a visible portion of the window. Default: A mouse
|
||||
# button must be clicked over a visible portion of the window.
|
||||
# CONFIG_NXFONTS_CHARBITS
|
||||
# The number of bits in the character set. Current options are
|
||||
# only 7 and 8. The default is 7.
|
||||
# CONFIG_NXFONT_SANS
|
||||
# At present, there is only one font. But if there were were more,
|
||||
# then this option would select the sans serif font.
|
||||
#
|
||||
# NX Multi-user only options:
|
||||
#
|
||||
# CONFIG_NX_BLOCKING
|
||||
# Open the client message queues in blocking mode. In this case,
|
||||
# nx_eventhandler() will not return until a message is received and processed.
|
||||
# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
|
||||
# Specifies the maximum number of messages that can fit in
|
||||
# the message queues. No additional resources are allocated, but
|
||||
# this can be set to prevent flooding of the client or server with
|
||||
# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
|
||||
# messages are pre-allocated).
|
||||
#
|
||||
CONFIG_NX=y
|
||||
CONFIG_NX_MULTIUSER=n
|
||||
CONFIG_NX_NPLANES=1
|
||||
CONFIG_NX_DISABLE_1BPP=y
|
||||
CONFIG_NX_DISABLE_2BPP=y
|
||||
CONFIG_NX_DISABLE_4BPP=n
|
||||
CONFIG_NX_DISABLE_8BPP=y
|
||||
CONFIG_NX_DISABLE_16BPP=y
|
||||
CONFIG_NX_DISABLE_24BPP=y
|
||||
CONFIG_NX_DISABLE_32BPP=y
|
||||
CONFIG_NX_PACKEDMSFIRST=y
|
||||
CONFIG_NX_LCDDRIVER=y
|
||||
CONFIG_LCD_MAXPOWER=1
|
||||
CONFIG_LCD_MAXCONTRAST=255
|
||||
CONFIG_NX_MOUSE=y
|
||||
CONFIG_NX_KBD=y
|
||||
#CONFIG_NXTK_BORDERWIDTH=4
|
||||
CONFIG_NXTK_BORDERCOLOR1=8
|
||||
CONFIG_NXTK_BORDERCOLOR2=4
|
||||
CONFIG_NXTK_AUTORAISE=n
|
||||
CONFIG_NXFONT_SANS=y
|
||||
CONFIG_NXFONTS_CHARBITS=7
|
||||
CONFIG_NX_BLOCKING=y
|
||||
CONFIG_NX_MXSERVERMSGS=32
|
||||
CONFIG_NX_MXCLIENTMSGS=16
|
||||
|
||||
# RiT P14201 OLED Driver Configuration
|
||||
#
|
||||
# CONFIG_LCD_P14201 - Enable P14201 support
|
||||
# CONFIG_P14201_SPIMODE - Controls the SPI mode (should be mode 2)
|
||||
# CONFIG_P14201_FREQUENCY - Define to use a different bus frequency
|
||||
# CONFIG_P14201_NINTERFACES - Specifies the number of physical P14201 devices that
|
||||
# will be supported.
|
||||
# CONFIG_P14201_FRAMEBUFFER - If defined, accesses will be performed using an in-memory
|
||||
# copy of the OLEDs GDDRAM. This cost of this buffer is 128 * 96 / 2 = 6Kb. If this
|
||||
# is defined, then the driver will be fully functional. If not, then it will have the
|
||||
# following limitations:
|
||||
# - Reading graphics memory cannot be supported, and
|
||||
# - All pixel writes must be aligned to byte boundaries.
|
||||
#
|
||||
# The latter limitation effectively reduces the 128x96 disply to 64x96.
|
||||
CONFIG_LCD_P14201=y
|
||||
CONFIG_P14201_SPIMODE=2
|
||||
CONFIG_P14201_FREQUENCY=3500000
|
||||
CONFIG_P14201_NINTERFACES=1
|
||||
CONFIG_P14201_FRAMEBUFFER=y
|
||||
|
||||
#
|
||||
# Settings for examples/uip
|
||||
#
|
||||
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
|
||||
#
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
# Settings for examples/nsh
|
||||
#
|
||||
# CONFIG_EXAMPLES_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_EXAMPLES_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_EXAMPLES_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_EXAMPLES_NSH_STACKSIZE - Stack size to use for new threads.
|
||||
# CONFIG_EXAMPLES_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_EXAMPLES_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_EXAMPLES_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_EXAMPLES_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_EXAMPLES_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_EXAMPLES_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_EXAMPLES_NSH_TELNET is selected:
|
||||
# CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_EXAMPLES_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_EXAMPLES_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_EXAMPLES_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_EXAMPLES_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_EXAMPLES_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_EXAMPLES_NSH_ROMFSETC is selected:
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_EXAMPLES_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_EXAMPLES_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_EXAMPLES_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_EXAMPLES_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_EXAMPLES_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_EXAMPLES_NSH_FILEIOSIZE=512
|
||||
CONFIG_EXAMPLES_NSH_STRERROR=n
|
||||
CONFIG_EXAMPLES_NSH_LINELEN=64
|
||||
CONFIG_EXAMPLES_NSH_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_NSH_NESTDEPTH=3
|
||||
CONFIG_EXAMPLES_NSH_DISABLESCRIPT=n
|
||||
CONFIG_EXAMPLES_NSH_DISABLEBG=n
|
||||
CONFIG_EXAMPLES_NSH_ROMFSETC=n
|
||||
CONFIG_EXAMPLES_NSH_CONSOLE=y
|
||||
CONFIG_EXAMPLES_NSH_TELNET=n
|
||||
CONFIG_EXAMPLES_NSH_ARCHINIT=n
|
||||
CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE=512
|
||||
CONFIG_EXAMPLES_NSH_DHCPC=n
|
||||
CONFIG_EXAMPLES_NSH_NOMAC=n
|
||||
CONFIG_EXAMPLES_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLES_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLES_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT="/etc"
|
||||
CONFIG_EXAMPLES_NSH_INITSCRIPT="init.d/rcS"
|
||||
CONFIG_EXAMPLES_NSH_ROMFSDEVNO=0
|
||||
CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE=64
|
||||
CONFIG_EXAMPLES_NSH_FATDEVNO=1
|
||||
CONFIG_EXAMPLES_NSH_FATSECTSIZE=512
|
||||
CONFIG_EXAMPLES_NSH_FATNSECTORS=1024
|
||||
CONFIG_EXAMPLES_NSH_FATMOUNTPT=/tmp
|
||||
|
||||
#
|
||||
# Architecture-specific NSH options
|
||||
#
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO=0
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSLOTNO=0
|
||||
CONFIG_EXAMPLES_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Settings for examples/nx
|
||||
#
|
||||
# CONFIG_EXAMPLES_NX_VPLANE -- The plane to select from the frame-
|
||||
# buffer driver for use in the test. Default: 0
|
||||
# CONFIG_EXAMPLES_NX_DEVNO - The LCD device to select from the LCD
|
||||
# driver for use in the test: Default: 0
|
||||
# CONFIG_EXAMPLES_NX_BGCOLOR -- The color of the background. Default depends on
|
||||
# CONFIG_EXAMPLES_NX_BPP.
|
||||
# CONFIG_EXAMPLES_NX_COLOR1 -- The color of window 1. Default depends on
|
||||
# CONFIG_EXAMPLES_NX_BPP.
|
||||
# CONFIG_EXAMPLES_NX_COLOR2 -- The color of window 2. Default depends on
|
||||
# CONFIG_EXAMPLES_NX_BPP.
|
||||
# CONFIG_EXAMPLES_NX_TBCOLOR -- The color of the toolbar. Default depends on
|
||||
# CONFIG_EXAMPLES_NX_BPP.
|
||||
# CONFIG_EXAMPLES_NX_FONTCOLOR -- The color of the toolbar. Default depends on
|
||||
# CONFIG_EXAMPLES_NX_BPP.
|
||||
# CONFIG_EXAMPLES_NX_BPP -- Pixels per pixel to use. Valid options
|
||||
# include 2, 4, 8, 16, 24, and 32. Default is 32.
|
||||
# CONFIG_EXAMPLES_NX_RAWWINDOWS -- Use raw windows; Default is to
|
||||
# use pretty, framed NXTK windows with toolbars.
|
||||
# CONFIG_EXAMPLES_NX_STACKSIZE -- The stacksize to use when creating
|
||||
# the NX server. Default 2048
|
||||
# CONFIG_EXAMPLES_NX_CLIENTPRIO -- The client priority. Default: 80
|
||||
# CONFIG_EXAMPLES_NX_SERVERPRIO -- The server priority. Default: 120
|
||||
# CONFIG_EXAMPLES_NX_NOTIFYSIGNO -- The signal number to use with
|
||||
# nx_eventnotify(). Default: 4
|
||||
CONFIG_EXAMPLES_NX_VPLANE=0
|
||||
CONFIG_EXAMPLES_NX_DEVNO=0
|
||||
CONFIG_EXAMPLES_NX_BGCOLOR=2
|
||||
CONFIG_EXAMPLES_NX_COLOR1=10
|
||||
CONFIG_EXAMPLES_NX_COLOR2=12
|
||||
CONFIG_EXAMPLES_NX_TBCOLOR=8
|
||||
CONFIG_EXAMPLES_NX_FONTCOLOR=0
|
||||
CONFIG_EXAMPLES_NX_BPP=4
|
||||
CONFIG_EXAMPLES_NX_RAWWINDOWS=n
|
||||
CONFIG_EXAMPLES_NX_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_NX_CLIENTPRIO=80
|
||||
CONFIG_EXAMPLES_NX_SERVERPRIO=120
|
||||
CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
|
||||
CONFIG_EXAMPLES_NX_EXTERNINIT=y
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should also be =n for the LM3S8962 Eval Kit which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=n
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
CONFIG_STACK_POINTER=
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
CONFIG_HEAP_BASE=
|
||||
CONFIG_HEAP_SIZE=
|
||||
108
configs/lm3s8962-ek/nx/ld.script
Executable file
108
configs/lm3s8962-ek/nx/ld.script
Executable file
@ -0,0 +1,108 @@
|
||||
/****************************************************************************
|
||||
* configs/lm3s8962-ek/nx/ld.script
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The LM3S8962 has 256Kb of FLASH beginning at address 0x0000:0000 and 64Kb
|
||||
* of SRAM beginning at 0x2000:0000.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x00000000, LENGTH = 256K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.); /* See below */
|
||||
|
||||
/* The LM3S6918 has 64Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
.ARM.exidx : {
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
*(.ARM.exidx*)
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
} >sram
|
||||
|
||||
.bss : { /* BSS */
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
||||
46
configs/lm3s8962-ek/nx/setenv.sh
Executable file
46
configs/lm3s8962-ek/nx/setenv.sh
Executable file
@ -0,0 +1,46 @@
|
||||
#!/bin/bash
|
||||
# configs/lm3s8962-ek/nx/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$(basename $0)" = "setenv.sh" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
|
||||
|
||||
WD=`pwd`
|
||||
export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
export PATH="${BUILDROOT_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
||||
162
configs/lm3s8962-ek/ostest/Make.defs
Executable file
162
configs/lm3s8962-ek/ostest/Make.defs
Executable file
@ -0,0 +1,162 @@
|
||||
############################################################################
|
||||
# configs/lm3s8962-ek/ostest/Make.defs
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
|
||||
# Setup for the selected toolchain
|
||||
|
||||
ifeq ($(CONFIG_LM3S_CODESOURCERYW),y)
|
||||
# CodeSourcery under Windows
|
||||
CROSSDEV = arm-none-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_CODESOURCERYL),y)
|
||||
# CodeSourcery under Linux
|
||||
CROSSDEV = arm-none-eabi-
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -O2
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_DEVKITARM),y)
|
||||
# devkitARM under Windows
|
||||
CROSSDEV = arm-eabi-
|
||||
WINTOOL = y
|
||||
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
||||
endif
|
||||
ifeq ($(CONFIG_LM3S_BUILDROOT),y)
|
||||
# NuttX buildroot under Linux or Cygwin
|
||||
CROSSDEV = arm-elf-
|
||||
ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
||||
MAXOPTIMIZATION = -Os
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/winlink.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/ostest/ld.script}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/ostest/ld.script
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
|
||||
ARCHOPTIMIZATION = -g
|
||||
else
|
||||
ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
define PREPROCESS
|
||||
@echo "CPP: $1->$2"
|
||||
@$(CPP) $(CPPFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILE
|
||||
@echo "CC: $1"
|
||||
@$(CC) -c $(CFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define COMPILEXX
|
||||
@echo "CXX: $1"
|
||||
@$(CXX) -c $(CXXFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ASSEMBLE
|
||||
@echo "AS: $1"
|
||||
@$(CC) -c $(AFLAGS) $1 -o $2
|
||||
endef
|
||||
|
||||
define ARCHIVE
|
||||
echo "AR: $2"; \
|
||||
$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
|
||||
endef
|
||||
|
||||
define CLEAN
|
||||
@rm -f *.o *.a
|
||||
endef
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
||||
619
configs/lm3s8962-ek/ostest/defconfig
Executable file
619
configs/lm3s8962-ek/ostest/defconfig
Executable file
@ -0,0 +1,619 @@
|
||||
############################################################################
|
||||
# configs/lm3s8962-ek/ostest/defconfig
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
||||
# CONFIG_ARCH_IRQPRIO - The LM3S8962 supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibratre
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
#
|
||||
CONFIG_ARCH=arm
|
||||
CONFIG_ARCH_ARM=y
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
CONFIG_ARCH_CHIP=lm3s
|
||||
CONFIG_ARCH_CHIP_LM3S8962=y
|
||||
CONFIG_ARCH_BOARD=lm3s8962-ek
|
||||
CONFIG_ARCH_BOARD_LM3S8962EK=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=4531
|
||||
CONFIG_DRAM_SIZE=0x00010000
|
||||
CONFIG_DRAM_START=0x20000000
|
||||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=n
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_CALIBRATION=n
|
||||
|
||||
#
|
||||
# Identify toolchain and linker options
|
||||
#
|
||||
CONFIG_LM3S_CODESOURCERYW=n
|
||||
CONFIG_LM3S_CODESOURCERYL=n
|
||||
CONFIG_LM3S_DEVKITARM=n
|
||||
CONFIG_LM3S_BUILDROOT=y
|
||||
CONFIG_LM3S_DFU=y
|
||||
|
||||
#
|
||||
# Disable support for interrupts on GPIOH and GPIOJ which do not
|
||||
# exist on the LM3S6B96. Additional interrupt support can be
|
||||
# disabled if desired to reduce memory footprint.
|
||||
CONFIG_LM3S_DISABLE_GPIOA_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOB_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOC_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOD_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOE_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOF_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOG_IRQS=n
|
||||
CONFIG_LM3S_DISABLE_GPIOH_IRQS=y
|
||||
CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y
|
||||
|
||||
#
|
||||
# LM3S8962 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_UARTn_DISABLE - select to disable all support for
|
||||
# the UART
|
||||
# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||||
# console and ttys0 (default is the UART0).
|
||||
# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_UARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_UART0_DISABLE=n
|
||||
CONFIG_UART1_DISABLE=y
|
||||
CONFIG_UART2_DISABLE=y
|
||||
CONFIG_UART0_SERIAL_CONSOLE=y
|
||||
CONFIG_UART1_SERIAL_CONSOLE=n
|
||||
CONFIG_UART2_SERIAL_CONSOLE=n
|
||||
CONFIG_UART0_TXBUFSIZE=256
|
||||
CONFIG_UART1_TXBUFSIZE=256
|
||||
CONFIG_UART2_TXBUFSIZE=256
|
||||
CONFIG_UART0_RXBUFSIZE=256
|
||||
CONFIG_UART1_RXBUFSIZE=256
|
||||
CONFIG_UART2_RXBUFSIZE=256
|
||||
CONFIG_UART0_BAUD=115200
|
||||
CONFIG_UART1_BAUD=115200
|
||||
CONFIG_UART2_BAUD=115200
|
||||
CONFIG_UART0_BITS=8
|
||||
CONFIG_UART1_BITS=8
|
||||
CONFIG_UART2_BITS=8
|
||||
CONFIG_UART0_PARITY=0
|
||||
CONFIG_UART1_PARITY=0
|
||||
CONFIG_UART2_PARITY=0
|
||||
CONFIG_UART0_2STOP=0
|
||||
CONFIG_UART1_2STOP=0
|
||||
CONFIG_UART2_2STOP=0
|
||||
|
||||
#
|
||||
# LM3S8962 specific SSI device driver settings
|
||||
#
|
||||
# CONFIG_SSIn_DISABLE - select to disable all support for
|
||||
# the SSI
|
||||
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
|
||||
# Poll-waiting is recommended if the interrupt rate would be to
|
||||
# high in the interrupt driven case.
|
||||
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
# emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
# value is large, then larger values of this setting may cause
|
||||
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
#
|
||||
CONFIG_SSI0_DISABLE=n
|
||||
CONFIG_SSI1_DISABLE=y
|
||||
CONFIG_SSI_POLLWAIT=y
|
||||
#CONFIG_SSI_TXLIMIT=4
|
||||
|
||||
#
|
||||
# LM3S8962 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET)
|
||||
# to build the LM3S Ethernet driver
|
||||
# CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
||||
# CONFIG_LM3S_BOARDMAC - If the board-specific logic can provide
|
||||
# a MAC address (via lm3s_ethernetmac()), then this should be selected.
|
||||
# CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation
|
||||
# CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
||||
# CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding
|
||||
# CONFIG_LM3S_MULTICAST - Set to enable multicast frames
|
||||
# CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode
|
||||
# CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection.
|
||||
# CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console.
|
||||
#
|
||||
CONFIG_LM3S_ETHERNET=n
|
||||
CONFIG_LM3S_ETHLEDS=n
|
||||
CONFIG_LM3S_BOARDMAC=y
|
||||
CONFIG_LM3S_ETHHDUPLEX=n
|
||||
CONFIG_LM3S_ETHNOAUTOCRC=n
|
||||
CONFIG_LM3S_ETHNOPAD=n
|
||||
CONFIG_LM3S_MULTICAST=n
|
||||
CONFIG_LM3S_PROMISCUOUS=n
|
||||
CONFIG_LM3S_BADCRC=n
|
||||
CONFIG_LM3S_DUMPPACKET=n
|
||||
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=n
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
CONFIG_RAW_BINARY=y
|
||||
CONFIG_HAVE_LIBM=n
|
||||
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APP_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX.
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_TICKS_PER_MSEC - The default system timer is 100Hz
|
||||
# or TICKS_PER_MSEC=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
||||
# You would only need this if you are concerned about accurate
|
||||
# time conversions in the past or in the distant future.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
||||
# would only need this if you are concerned about accurate
|
||||
# time conversion in the distand past. You must also define
|
||||
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
#
|
||||
CONFIG_APP_DIR=examples/ostest
|
||||
CONFIG_DEBUG=n
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
CONFIG_MM_REGIONS=1
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_INSTRUMENTATION=n
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
CONFIG_START_YEAR=2010
|
||||
CONFIG_START_MONTH=5
|
||||
CONFIG_START_DAY=6
|
||||
CONFIG_GREGORIAN_TIME=n
|
||||
CONFIG_JULIAN_TIME=n
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
CONFIG_DEV_LOWCONSOLE=y
|
||||
CONFIG_MUTEX_TYPES=n
|
||||
CONFIG_PRIORITY_INHERITANCE=n
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SEM_NNESTPRIO=0
|
||||
CONFIG_FDCLONE_DISABLE=n
|
||||
CONFIG_FDCLONE_STDIO=n
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_NXFLAT=n
|
||||
|
||||
#
|
||||
# The following can be used to disable categories of
|
||||
# APIs supported by the OS. If the compiler supports
|
||||
# weak functions, then it should not be necessary to
|
||||
# disable functions unless you want to restrict usage
|
||||
# of those APIs.
|
||||
#
|
||||
# There are certain dependency relationships in these
|
||||
# features.
|
||||
#
|
||||
# o mq_notify logic depends on signals to awaken tasks
|
||||
# waiting for queues to become full or empty.
|
||||
# o pthread_condtimedwait() depends on signals to wake
|
||||
# up waiting tasks.
|
||||
#
|
||||
CONFIG_DISABLE_CLOCK=n
|
||||
CONFIG_DISABLE_POSIX_TIMERS=n
|
||||
CONFIG_DISABLE_PTHREAD=n
|
||||
CONFIG_DISABLE_SIGNALS=n
|
||||
CONFIG_DISABLE_MQUEUE=n
|
||||
CONFIG_DISABLE_MOUNTPOINT=y
|
||||
CONFIG_DISABLE_ENVIRON=y
|
||||
CONFIG_DISABLE_POLL=y
|
||||
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
# Allow for architecture optimized implementations
|
||||
#
|
||||
# The architecture can provide optimized versions of the
|
||||
# following to improve system performance
|
||||
#
|
||||
CONFIG_ARCH_MEMCPY=n
|
||||
CONFIG_ARCH_MEMCMP=n
|
||||
CONFIG_ARCH_MEMMOVE=n
|
||||
CONFIG_ARCH_MEMSET=n
|
||||
CONFIG_ARCH_STRCMP=n
|
||||
CONFIG_ARCH_STRCPY=n
|
||||
CONFIG_ARCH_STRNCPY=n
|
||||
CONFIG_ARCH_STRLEN=n
|
||||
CONFIG_ARCH_BZERO=n
|
||||
CONFIG_ARCH_KMALLOC=n
|
||||
CONFIG_ARCH_KZMALLOC=n
|
||||
CONFIG_ARCH_KFREE=n
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=16
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=8
|
||||
CONFIG_NFILE_STREAMS=8
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_STDIO_BUFFER_SIZE=256
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
CONFIG_FS_FAT=n
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_LLH_LEN - The link level header length
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=n
|
||||
CONFIG_NET_IPv6=n
|
||||
CONFIG_NSOCKET_DESCRIPTORS=0
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=420
|
||||
CONFIG_NET_TCP=n
|
||||
CONFIG_NET_TCP_CONNS=40
|
||||
CONFIG_NET_MAX_LISTENPORTS=40
|
||||
CONFIG_NET_UDP=n
|
||||
CONFIG_NET_UDP_CHECKSUMS=y
|
||||
#CONFIG_NET_UDP_CONNS=10
|
||||
CONFIG_NET_ICMP=n
|
||||
CONFIG_NET_ICMP_PING=n
|
||||
#CONFIG_NET_PINGADDRCONF=0
|
||||
CONFIG_NET_STATISTICS=y
|
||||
#CONFIG_NET_RECEIVE_WINDOW=
|
||||
#CONFIG_NET_ARPTAB_SIZE=8
|
||||
CONFIG_NET_BROADCAST=n
|
||||
#CONFIG_NET_LLH_LEN=14
|
||||
#CONFIG_NET_FWCACHE_SIZE=2
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
|
||||
#
|
||||
# Settings for examples/uip
|
||||
#
|
||||
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
||||
|
||||
#
|
||||
# Settings for examples/ostest
|
||||
#
|
||||
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
||||
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
|
||||
#
|
||||
# Settings for examples/nsh
|
||||
#
|
||||
# CONFIG_EXAMPLES_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_EXAMPLES_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_EXAMPLES_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_EXAMPLES_NSH_STACKSIZE - Stack size to use for new threads.
|
||||
# CONFIG_EXAMPLES_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_EXAMPLES_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_EXAMPLES_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_EXAMPLES_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_EXAMPLES_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_EXAMPLES_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_EXAMPLES_NSH_TELNET is selected:
|
||||
# CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_EXAMPLES_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_EXAMPLES_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_EXAMPLES_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_EXAMPLES_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_EXAMPLES_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_EXAMPLES_NSH_ROMFSETC is selected:
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_EXAMPLES_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_EXAMPLES_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_EXAMPLES_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_EXAMPLES_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_EXAMPLES_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_EXAMPLES_NSH_FILEIOSIZE=512
|
||||
CONFIG_EXAMPLES_NSH_STRERROR=n
|
||||
CONFIG_EXAMPLES_NSH_LINELEN=64
|
||||
CONFIG_EXAMPLES_NSH_STACKSIZE=2048
|
||||
CONFIG_EXAMPLES_NSH_NESTDEPTH=3
|
||||
CONFIG_EXAMPLES_NSH_DISABLESCRIPT=n
|
||||
CONFIG_EXAMPLES_NSH_DISABLEBG=n
|
||||
CONFIG_EXAMPLES_NSH_ROMFSETC=n
|
||||
CONFIG_EXAMPLES_NSH_CONSOLE=y
|
||||
CONFIG_EXAMPLES_NSH_TELNET=n
|
||||
CONFIG_EXAMPLES_NSH_ARCHINIT=n
|
||||
CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE=512
|
||||
CONFIG_EXAMPLES_NSH_DHCPC=n
|
||||
CONFIG_EXAMPLES_NSH_NOMAC=n
|
||||
CONFIG_EXAMPLES_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
||||
CONFIG_EXAMPLES_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
||||
CONFIG_EXAMPLES_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
||||
CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT="/etc"
|
||||
CONFIG_EXAMPLES_NSH_INITSCRIPT="init.d/rcS"
|
||||
CONFIG_EXAMPLES_NSH_ROMFSDEVNO=0
|
||||
CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE=64
|
||||
CONFIG_EXAMPLES_NSH_FATDEVNO=1
|
||||
CONFIG_EXAMPLES_NSH_FATSECTSIZE=512
|
||||
CONFIG_EXAMPLES_NSH_FATNSECTORS=1024
|
||||
CONFIG_EXAMPLES_NSH_FATMOUNTPT=/tmp
|
||||
|
||||
#
|
||||
# Architecture-specific NSH options
|
||||
#
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO=0
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSLOTNO=0
|
||||
CONFIG_EXAMPLES_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should also be =n for the LM3S8962 Eval Kit which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=n
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
CONFIG_STACK_POINTER=
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
CONFIG_HEAP_BASE=
|
||||
CONFIG_HEAP_SIZE=
|
||||
108
configs/lm3s8962-ek/ostest/ld.script
Executable file
108
configs/lm3s8962-ek/ostest/ld.script
Executable file
@ -0,0 +1,108 @@
|
||||
/****************************************************************************
|
||||
* configs/lm3s8962-ek/ostest/ld.script
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The LM3S8962 has 256Kb of FLASH beginning at address 0x0000:0000 and 64Kb
|
||||
* of SRAM beginning at 0x2000:0000.
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x00000000, LENGTH = 256K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
ENTRY(_stext)
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
_eronly = ABSOLUTE(.); /* See below */
|
||||
|
||||
/* The LM3S6918 has 64Kb of SRAM beginning at the following address */
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} >sram
|
||||
|
||||
.ARM.exidx : {
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
*(.ARM.exidx*)
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
} >sram
|
||||
|
||||
.bss : { /* BSS */
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
||||
46
configs/lm3s8962-ek/ostest/setenv.sh
Executable file
46
configs/lm3s8962-ek/ostest/setenv.sh
Executable file
@ -0,0 +1,46 @@
|
||||
#!/bin/bash
|
||||
# configs/lm3s8962-ek/ostest/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$(basename $0)" = "setenv.sh" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
|
||||
|
||||
WD=`pwd`
|
||||
export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
export PATH="${BUILDROOT_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
||||
90
configs/lm3s8962-ek/src/Makefile
Executable file
90
configs/lm3s8962-ek/src/Makefile
Executable file
@ -0,0 +1,90 @@
|
||||
############################################################################
|
||||
# configs/lm3s8962-ek/src/Makefile
|
||||
#
|
||||
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
-include $(TOPDIR)/Make.defs
|
||||
|
||||
CFLAGS += -I$(TOPDIR)/sched
|
||||
|
||||
ASRCS =
|
||||
AOBJS = $(ASRCS:.S=$(OBJEXT))
|
||||
CSRCS = up_boot.c up_leds.c up_ethernet.c up_ssi.c
|
||||
ifeq ($(CONFIG_EXAMPLES_NSH_ARCHINIT),y)
|
||||
CSRCS += up_nsh.c
|
||||
endif
|
||||
ifeq ($(CONFIG_NX_LCDDRIVER),y)
|
||||
CSRCS += up_oled.c
|
||||
endif
|
||||
|
||||
COBJS = $(CSRCS:.c=$(OBJEXT))
|
||||
|
||||
SRCS = $(ASRCS) $(CSRCS)
|
||||
OBJS = $(AOBJS) $(COBJS)
|
||||
|
||||
ARCH_SRCDIR = $(TOPDIR)/arch/$(CONFIG_ARCH)/src
|
||||
ifeq ($(WINTOOL),y)
|
||||
CFLAGS += -I "${shell cygpath -w $(ARCH_SRCDIR)/chip}" \
|
||||
-I "${shell cygpath -w $(ARCH_SRCDIR)/common}" \
|
||||
-I "${shell cygpath -w $(ARCH_SRCDIR)/cortexm3}"
|
||||
else
|
||||
CFLAGS += -I$(ARCH_SRCDIR)/chip -I$(ARCH_SRCDIR)/common -I$(ARCH_SRCDIR)/cortexm3
|
||||
endif
|
||||
|
||||
all: libboard$(LIBEXT)
|
||||
|
||||
$(AOBJS): %$(OBJEXT): %.S
|
||||
$(call ASSEMBLE, $<, $@)
|
||||
|
||||
$(COBJS) $(LINKOBJS): %$(OBJEXT): %.c
|
||||
$(call COMPILE, $<, $@)
|
||||
|
||||
libboard$(LIBEXT): $(OBJS)
|
||||
@( for obj in $(OBJS) ; do \
|
||||
$(call ARCHIVE, $@, $${obj}); \
|
||||
done ; )
|
||||
|
||||
.depend: Makefile $(SRCS)
|
||||
@$(MKDEP) $(CC) -- $(CFLAGS) -- $(SRCS) >Make.dep
|
||||
@touch $@
|
||||
|
||||
depend: .depend
|
||||
|
||||
clean:
|
||||
@rm -f libboard$(LIBEXT) *~ .*.swp
|
||||
$(call CLEAN)
|
||||
|
||||
distclean: clean
|
||||
@rm -f Make.dep .depend
|
||||
|
||||
-include Make.dep
|
||||
1
configs/lm3s8962-ek/src/README.txt
Executable file
1
configs/lm3s8962-ek/src/README.txt
Executable file
@ -0,0 +1 @@
|
||||
This directory contains drivers unique to the Stellaris LM3S8962 Evaluation Kit.
|
||||
136
configs/lm3s8962-ek/src/lm3s8962ek_internal.h
Executable file
136
configs/lm3s8962-ek/src/lm3s8962ek_internal.h
Executable file
@ -0,0 +1,136 @@
|
||||
/************************************************************************************
|
||||
* configs/lm3s8962-ek/src/lm3s8962ek_internal.h
|
||||
* arch/arm/src/board/lm3s8962ek_internal.n
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __CONFIGS_LM3S8962_EK_SRC_LM3S8962EK_INTERNAL_H
|
||||
#define __CONFIGS_LM3S8962_EK_SRC_LM3S8962EK_INTERNAL_H
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#include <nuttx/compiler.h>
|
||||
|
||||
#include "chip.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/* How many SSI modules does this chip support? The LM3S8962 supports 1 SSI
|
||||
* module (others may support more than 2 -- in such case, the following must be
|
||||
* expanded).
|
||||
*/
|
||||
|
||||
#if LM3S_NSSI == 0
|
||||
# undef CONFIG_SSI0_DISABLE
|
||||
# define CONFIG_SSI0_DISABLE 1
|
||||
# undef CONFIG_SSI1_DISABLE
|
||||
# define CONFIG_SSI1_DISABLE 1
|
||||
#elif LM3S_NSSI == 1
|
||||
# undef CONFIG_SSI1_DISABLE
|
||||
# define CONFIG_SSI1_DISABLE 1
|
||||
#endif
|
||||
|
||||
/* LM3S8962 Eval Kit ***************************************************************/
|
||||
|
||||
/* GPIO Usage
|
||||
*
|
||||
* PIN SIGNAL EVB Function
|
||||
* --- ----------- ---------------------------------------
|
||||
* 26 PA0/U0RX Virtual COM port receive
|
||||
* 27 PA1/U0TX Virtual COM port transmit
|
||||
* 10 PD0/IDX0 SD card chip select
|
||||
* 11 PD1/PWM1 Sound
|
||||
* 30 PA4/SSI0RX SD card data out
|
||||
* 31 PA5/SSI0TX SD card and OLED display data in
|
||||
* 28 PA2/SSI0CLK SD card and OLED display clock
|
||||
* 22 PC7/PHB0 OLED display data/control select
|
||||
* 29 PA3/SSI0FSS OLED display chip select
|
||||
* 73 PE1/PWM5 Down switch
|
||||
* 74 PE2/PHB1 Left switch
|
||||
* 72 PE0/PWM4 Up switch
|
||||
* 75 PE3/PHA1 Right switch
|
||||
* 61 PF1/IDX1 Select switch
|
||||
* 47 PF0/PWM0 User LED
|
||||
* 23 PC6/CCP3 Enable +15 V
|
||||
*/
|
||||
|
||||
/* GPIO for microSD card chip select:
|
||||
* - PD0: SD card chip select (CARDCSn)
|
||||
*/
|
||||
|
||||
#define SDCCS_GPIO (GPIO_FUNC_OUTPUT | GPIO_PADTYPE_STDWPU | GPIO_STRENGTH_4MA | \
|
||||
GPIO_VALUE_ONE | GPIO_PORTD | 0)
|
||||
|
||||
/* GPIO for single LED:
|
||||
* - PF0: User LED
|
||||
*/
|
||||
|
||||
#define LED_GPIO (GPIO_FUNC_OUTPUT | GPIO_VALUE_ONE | GPIO_PORTF | 0)
|
||||
|
||||
/* GPIOs for OLED:
|
||||
* - PC7: OLED display data/control select (D/Cn)
|
||||
* - PA3: OLED display chip select (CSn)
|
||||
* - PC6: Enable +15V needed by OLED (EN+15V)
|
||||
*/
|
||||
|
||||
#define OLEDDC_GPIO (GPIO_FUNC_OUTPUT | GPIO_PADTYPE_STD | GPIO_STRENGTH_8MA | \
|
||||
GPIO_VALUE_ONE | GPIO_PORTC | 7)
|
||||
#define OLEDCS_GPIO (GPIO_FUNC_OUTPUT | GPIO_PADTYPE_STDWPU | GPIO_STRENGTH_4MA | \
|
||||
GPIO_VALUE_ONE | GPIO_PORTA | 3)
|
||||
#define OLEDEN_GPIO (GPIO_FUNC_OUTPUT | GPIO_PADTYPE_STD | GPIO_STRENGTH_8MA | \
|
||||
GPIO_VALUE_ONE | GPIO_PORTC | 6)
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
/************************************************************************************
|
||||
* Name: lm3s_ssiinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to configure SPI chip select GPIO pins for the LM3S8962 Eval Kit.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
extern void weak_function lm3s_ssiinitialize(void);
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
#endif /* __CONFIGS_LM3S8962_EK_SRC_LM3S8962EK_INTERNAL_H */
|
||||
|
||||
92
configs/lm3s8962-ek/src/up_boot.c
Executable file
92
configs/lm3s8962-ek/src/up_boot.c
Executable file
@ -0,0 +1,92 @@
|
||||
/************************************************************************************
|
||||
* configs/lm3s8962-ek/src/up_boot.c
|
||||
* arch/arm/src/board/up_boot.c
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <debug.h>
|
||||
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "up_arch.h"
|
||||
#include "up_internal.h"
|
||||
#include "lm3s8962ek_internal.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Private Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: lm3s_boardinitialize
|
||||
*
|
||||
* Description:
|
||||
* All LM3S architectures must provide the following entry point. This entry point
|
||||
* is called early in the intitialization -- after all memory has been configured
|
||||
* and mapped but before any devices have been initialized.
|
||||
************************************************************************************/
|
||||
|
||||
void lm3s_boardinitialize(void)
|
||||
{
|
||||
/* Configure SPI chip selects if 1) SSI is not disabled, and 2) the weak function
|
||||
* lm3s_ssiinitialize() has been brought into the link.
|
||||
*/
|
||||
|
||||
/* The LM3S8962 Eval Kit microSD CS and OLED are on SSI0 (Duh! There is no SSI1) */
|
||||
|
||||
#if !defined(CONFIG_SSI0_DISABLE) /* || !defined(CONFIG_SSI1_DISABLE) */
|
||||
if (lm3s_ssiinitialize)
|
||||
{
|
||||
lm3s_ssiinitialize();
|
||||
}
|
||||
#endif
|
||||
|
||||
/* Configure on-board LEDs if LED support has been selected. */
|
||||
|
||||
#ifdef CONFIG_ARCH_LEDS
|
||||
up_ledinit();
|
||||
#endif
|
||||
}
|
||||
98
configs/lm3s8962-ek/src/up_ethernet.c
Executable file
98
configs/lm3s8962-ek/src/up_ethernet.c
Executable file
@ -0,0 +1,98 @@
|
||||
/************************************************************************************
|
||||
* configs/lm3s8962-ek/src/up_ethernet.c
|
||||
* arch/arm/src/board/up_ethernet.c
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdint.h>
|
||||
#include <debug.h>
|
||||
#include <assert.h>
|
||||
|
||||
#include <arch/board/board.h>
|
||||
#include <net/ethernet.h>
|
||||
|
||||
#include "up_arch.h"
|
||||
#include "chip.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Private Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: lm3s_ethernetmac
|
||||
*
|
||||
* Description:
|
||||
* For the Ethernet Eval Kits, the MAC address will be stored in the non-volatile
|
||||
* USER0 and USER1 registers. If CONFIG_LM3S_BOARDMAC is defined, this function
|
||||
* will obtain the MAC address from these registers.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifdef CONFIG_LM3S_BOARDMAC
|
||||
void lm3s_ethernetmac(struct ether_addr *ethaddr)
|
||||
{
|
||||
uint32_t user0;
|
||||
uint32_t user1;
|
||||
|
||||
/* Get the current value of the user registers */
|
||||
|
||||
user0 = getreg32(LM3S_FLASH_USERREG0);
|
||||
user1 = getreg32(LM3S_FLASH_USERREG1);
|
||||
|
||||
nlldbg("user: %06x:%06x\n", user1 & 0x00ffffff, user0 & 0x00ffffff);
|
||||
DEBUGASSERT(user0 != 0xffffffff && user1 != 0xffffffff);
|
||||
|
||||
/* Re-format that MAC address the way that uIP expects to see it */
|
||||
|
||||
ethaddr->ether_addr_octet[0] = ((user0 >> 0) & 0xff);
|
||||
ethaddr->ether_addr_octet[1] = ((user0 >> 8) & 0xff);
|
||||
ethaddr->ether_addr_octet[2] = ((user0 >> 16) & 0xff);
|
||||
ethaddr->ether_addr_octet[3] = ((user1 >> 0) & 0xff);
|
||||
ethaddr->ether_addr_octet[4] = ((user1 >> 8) & 0xff);
|
||||
ethaddr->ether_addr_octet[5] = ((user1 >> 16) & 0xff);
|
||||
}
|
||||
#endif
|
||||
167
configs/lm3s8962-ek/src/up_leds.c
Executable file
167
configs/lm3s8962-ek/src/up_leds.c
Executable file
@ -0,0 +1,167 @@
|
||||
/****************************************************************************
|
||||
* configs/lm3s8962-ek/src/up_leds.c
|
||||
* arch/arm/src/board/up_leds.c
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdbool.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "chip.h"
|
||||
#include "up_arch.h"
|
||||
#include "up_internal.h"
|
||||
#include "lm3s_internal.h"
|
||||
#include "lm3s8962ek_internal.h"
|
||||
|
||||
/****************************************************************************
|
||||
* Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Enables debug output from this file (needs CONFIG_DEBUG with
|
||||
* CONFIG_DEBUG_VERBOSE too)
|
||||
*/
|
||||
|
||||
#undef LED_DEBUG /* Define to enable debug */
|
||||
|
||||
#ifdef LED_DEBUG
|
||||
# define leddbg lldbg
|
||||
# define ledvdbg llvdbg
|
||||
#else
|
||||
# define leddbg(x...)
|
||||
# define ledvdbg(x...)
|
||||
#endif
|
||||
|
||||
/* Dump GPIO registers */
|
||||
|
||||
#ifdef LED_DEBUG
|
||||
# define led_dumpgpio(m) lm3s_dumpgpio(LED_GPIO, m)
|
||||
#else
|
||||
# define led_dumpgpio(m)
|
||||
#endif
|
||||
|
||||
/****************************************************************************
|
||||
* Private Data
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Private Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
static uint8_t g_nest;
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_ledinit
|
||||
****************************************************************************/
|
||||
|
||||
#ifdef CONFIG_ARCH_LEDS
|
||||
void up_ledinit(void)
|
||||
{
|
||||
leddbg("Initializing\n");
|
||||
|
||||
/* Configure Port E, Bit 1 as an output, initial value=OFF */
|
||||
|
||||
led_dumpgpio("up_ledinit before lm3s_configgpio()");
|
||||
lm3s_configgpio(LED_GPIO);
|
||||
led_dumpgpio("up_ledinit after lm3s_configgpio()");
|
||||
g_nest = 0;
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_ledon
|
||||
****************************************************************************/
|
||||
|
||||
void up_ledon(int led)
|
||||
{
|
||||
switch (led)
|
||||
{
|
||||
case LED_STARTED:
|
||||
case LED_HEAPALLOCATE:
|
||||
default:
|
||||
break;
|
||||
|
||||
case LED_INIRQ:
|
||||
case LED_SIGNAL:
|
||||
case LED_ASSERTION:
|
||||
case LED_PANIC:
|
||||
g_nest++;
|
||||
case LED_IRQSENABLED:
|
||||
case LED_STACKCREATED:
|
||||
led_dumpgpio("up_ledon: before lm3s_gpiowrite()");
|
||||
lm3s_gpiowrite(LED_GPIO, false);
|
||||
led_dumpgpio("up_ledon: after lm3s_gpiowrite()");
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_ledoff
|
||||
****************************************************************************/
|
||||
|
||||
void up_ledoff(int led)
|
||||
{
|
||||
switch (led)
|
||||
{
|
||||
case LED_IRQSENABLED:
|
||||
case LED_STACKCREATED:
|
||||
case LED_STARTED:
|
||||
case LED_HEAPALLOCATE:
|
||||
default:
|
||||
break;
|
||||
|
||||
case LED_INIRQ:
|
||||
case LED_SIGNAL:
|
||||
case LED_ASSERTION:
|
||||
case LED_PANIC:
|
||||
if (--g_nest <= 0)
|
||||
{
|
||||
led_dumpgpio("up_ledoff: before lm3s_gpiowrite()");
|
||||
lm3s_gpiowrite(LED_GPIO, true);
|
||||
led_dumpgpio("up_ledoff: after lm3s_gpiowrite()");
|
||||
}
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
#endif /* CONFIG_ARCH_LEDS */
|
||||
159
configs/lm3s8962-ek/src/up_nsh.c
Executable file
159
configs/lm3s8962-ek/src/up_nsh.c
Executable file
@ -0,0 +1,159 @@
|
||||
/****************************************************************************
|
||||
* config/lm3s8962-ek/src/up_nsh.c
|
||||
* arch/arm/src/board/up_nsh.c
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdio.h>
|
||||
#include <debug.h>
|
||||
#include <errno.h>
|
||||
|
||||
#include <nuttx/spi.h>
|
||||
#include <nuttx/mmcsd.h>
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-Processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Configuration ************************************************************/
|
||||
|
||||
/* PORT and SLOT number probably depend on the board configuration */
|
||||
|
||||
#ifdef CONFIG_ARCH_BOARD_LM3S8962EK
|
||||
# undef CONFIG_EXAMPLES_NSH_HAVEUSBDEV
|
||||
# define CONFIG_EXAMPLES_NSH_HAVEMMCSD 1
|
||||
# if !defined(CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO) || CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO != 0
|
||||
# error "The LM3S8962 Eval Kit MMC/SD is on SSI0"
|
||||
# undef CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO
|
||||
# define CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO 0
|
||||
# endif
|
||||
# if !defined(CONFIG_EXAMPLES_NSH_MMCSDSLOTNO) || CONFIG_EXAMPLES_NSH_MMCSDSLOTNO != 0
|
||||
# error "The LM3S8962 Eval Kit MMC/SD is on SSI0 slot 0"
|
||||
# undef CONFIG_EXAMPLES_NSH_MMCSDSLOTNO
|
||||
# define CONFIG_EXAMPLES_NSH_MMCSDSLOTNO 0
|
||||
# endif
|
||||
#else
|
||||
/* Add configuration for new LM3s boards here */
|
||||
# error "Unrecognized lm3s board"
|
||||
# undef CONFIG_EXAMPLES_NSH_HAVEUSBDEV
|
||||
# undef CONFIG_EXAMPLES_NSH_HAVEMMCSD
|
||||
#endif
|
||||
|
||||
/* Can't support USB features if USB is not enabled */
|
||||
|
||||
#ifndef CONFIG_USBDEV
|
||||
# undef CONFIG_EXAMPLES_NSH_HAVEUSBDEV
|
||||
#endif
|
||||
|
||||
/* Can't support MMC/SD features if mountpoints are disabled */
|
||||
|
||||
#if defined(CONFIG_DISABLE_MOUNTPOINT)
|
||||
# undef CONFIG_EXAMPLES_NSH_HAVEMMCSD
|
||||
#endif
|
||||
|
||||
#ifndef CONFIG_EXAMPLES_NSH_MMCSDMINOR
|
||||
# define CONFIG_EXAMPLES_NSH_MMCSDMINOR 0
|
||||
#endif
|
||||
|
||||
/* Debug ********************************************************************/
|
||||
|
||||
#ifdef CONFIG_CPP_HAVE_VARARGS
|
||||
# ifdef CONFIG_DEBUG
|
||||
# define message(...) lib_lowprintf(__VA_ARGS__)
|
||||
# else
|
||||
# define message(...) printf(__VA_ARGS__)
|
||||
# endif
|
||||
#else
|
||||
# ifdef CONFIG_DEBUG
|
||||
# define message lib_lowprintf
|
||||
# else
|
||||
# define message printf
|
||||
# endif
|
||||
#endif
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: nsh_archinitialize
|
||||
*
|
||||
* Description:
|
||||
* Perform architecture specific initialization
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int nsh_archinitialize(void)
|
||||
{
|
||||
FAR struct spi_dev_s *spi;
|
||||
int ret;
|
||||
|
||||
/* Get the SPI port */
|
||||
|
||||
message("nsh_archinitialize: Initializing SPI port %d\n",
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO);
|
||||
|
||||
spi = up_spiinitialize(CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO);
|
||||
if (!spi)
|
||||
{
|
||||
message("nsh_archinitialize: Failed to initialize SPI port %d\n",
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO);
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
message("nsh_archinitialize: Successfully initialized SPI port %d\n",
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO);
|
||||
|
||||
/* Bind the SPI port to the slot */
|
||||
|
||||
message("nsh_archinitialize: Binding SPI port %d to MMC/SD slot %d\n",
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO, CONFIG_EXAMPLES_NSH_MMCSDSLOTNO);
|
||||
|
||||
ret = mmcsd_spislotinitialize(CONFIG_EXAMPLES_NSH_MMCSDMINOR, CONFIG_EXAMPLES_NSH_MMCSDSLOTNO, spi);
|
||||
if (ret < 0)
|
||||
{
|
||||
message("nsh_archinitialize: Failed to bind SPI port %d to MMC/SD slot %d: %d\n",
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO, CONFIG_EXAMPLES_NSH_MMCSDSLOTNO, ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
message("nsh_archinitialize: Successfuly bound SPI port %d to MMC/SD slot %d\n",
|
||||
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO, CONFIG_EXAMPLES_NSH_MMCSDSLOTNO);
|
||||
return OK;
|
||||
}
|
||||
162
configs/lm3s8962-ek/src/up_oled.c
Executable file
162
configs/lm3s8962-ek/src/up_oled.c
Executable file
@ -0,0 +1,162 @@
|
||||
/****************************************************************************
|
||||
* config/lm3s8962-ek/src/up_oled.c
|
||||
* arch/arm/src/board/up_oled.c
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdio.h>
|
||||
#include <debug.h>
|
||||
#include <errno.h>
|
||||
|
||||
#include <nuttx/spi.h>
|
||||
#include <nuttx/lcd.h>
|
||||
#include <nuttx/p14201.h>
|
||||
|
||||
#include "lm3s_internal.h"
|
||||
#include "lm3s8962ek_internal.h"
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-Processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Define the CONFIG_LCD_RITDEBUG to enable detailed debug output (stuff you
|
||||
* would never want to see unless you are debugging this file).
|
||||
*
|
||||
* Verbose debug must also be enabled
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_DEBUG
|
||||
# undef CONFIG_DEBUG_VERBOSE
|
||||
# undef CONFIG_DEBUG_GRAPHICS
|
||||
#endif
|
||||
|
||||
#ifndef CONFIG_DEBUG_VERBOSE
|
||||
# undef CONFIG_LCD_RITDEBUG
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_LCD_RITDEBUG
|
||||
# define ritdbg(format, arg...) vdbg(format, ##arg)
|
||||
# define oleddc_dumpgpio(m) lm3s_dumpgpio(OLEDDC_GPIO, m)
|
||||
# define oledcs_dumpgpio(m) lm3s_dumpgpio(OLEDCS_GPIO, m)
|
||||
#else
|
||||
# define ritdbg(x...)
|
||||
# define oleddc_dumpgpio(m)
|
||||
# define oledcs_dumpgpio(m)
|
||||
#endif
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: up_nxdrvinit
|
||||
*
|
||||
* Description:
|
||||
* Called NX initialization logic to configure the OLED.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
FAR struct lcd_dev_s *up_nxdrvinit(unsigned int devno)
|
||||
{
|
||||
FAR struct spi_dev_s *spi;
|
||||
FAR struct lcd_dev_s *dev;
|
||||
|
||||
/* Configure the OLED GPIOs */
|
||||
|
||||
oledcs_dumpgpio("up_nxdrvinit: After OLEDCS setup");
|
||||
oleddc_dumpgpio("up_nxdrvinit: On entry");
|
||||
|
||||
lm3s_configgpio(OLEDDC_GPIO); /* PC7: OLED display data/control select (D/Cn) */
|
||||
lm3s_configgpio(OLEDEN_GPIO); /* PC6: Enable +15V needed by OLED (EN+15V) */
|
||||
|
||||
oleddc_dumpgpio("up_nxdrvinit: After OLEDDC/EN setup");
|
||||
|
||||
/* Get the SSI port (configure as a Freescale SPI port) */
|
||||
|
||||
spi = up_spiinitialize(0);
|
||||
if (!spi)
|
||||
{
|
||||
glldbg("Failed to initialize SSI port 0\n");
|
||||
}
|
||||
else
|
||||
{
|
||||
/* Bind the SSI port to the OLED */
|
||||
|
||||
dev = rit_initialize(spi, devno);
|
||||
if (!dev)
|
||||
{
|
||||
glldbg("Failed to bind SSI port 0 to OLED %d: %d\n", devno);
|
||||
}
|
||||
else
|
||||
{
|
||||
gllvdbg("Bound SSI port 0 to OLED %d\n", devno);
|
||||
|
||||
/* And turn the OLED on (CONFIG_LCD_MAXPOWER should be 1) */
|
||||
|
||||
(void)dev->setpower(dev, CONFIG_LCD_MAXPOWER);
|
||||
return dev;
|
||||
}
|
||||
}
|
||||
return NULL;
|
||||
}
|
||||
|
||||
/******************************************************************************
|
||||
* Name: rit_seldata
|
||||
*
|
||||
* Description:
|
||||
* Set or clear the SD1329 D/Cn bit to select data (true) or command
|
||||
* (false). This function must be provided by platform-specific logic.
|
||||
*
|
||||
* Input Parameters:
|
||||
*
|
||||
* devno - A value in the range of 0 throuh CONFIG_P14201_NINTERFACES-1.
|
||||
* This allows support for multiple OLED devices.
|
||||
* data - true: select data; false: select command
|
||||
*
|
||||
* Returned Value:
|
||||
* None
|
||||
*
|
||||
******************************************************************************/
|
||||
|
||||
void rit_seldata(unsigned int devno, bool data)
|
||||
{
|
||||
/* Set GPIO to 1 for data, 0 for command */
|
||||
|
||||
lm3s_gpiowrite(OLEDDC_GPIO, data);
|
||||
}
|
||||
164
configs/lm3s8962-ek/src/up_ssi.c
Executable file
164
configs/lm3s8962-ek/src/up_ssi.c
Executable file
@ -0,0 +1,164 @@
|
||||
/************************************************************************************
|
||||
* configs/lm3s8962-ek/src/up_ssi.c
|
||||
* arch/arm/src/board/up_ssi.c
|
||||
*
|
||||
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdint.h>
|
||||
#include <stdbool.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <nuttx/spi.h>
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "up_arch.h"
|
||||
#include "chip.h"
|
||||
#include "lm3s_internal.h"
|
||||
#include "lm3s8962ek_internal.h"
|
||||
|
||||
/* The LM3S8962 Eval Kit microSD CS is on SSI0 */
|
||||
|
||||
#if !defined(CONFIG_SSI0_DISABLE) /* || !defined(CONFIG_SSI1_DISABLE) */
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/* Enables debug output from this file (needs CONFIG_DEBUG too) */
|
||||
|
||||
#undef SSI_DEBUG /* Define to enable debug */
|
||||
#undef SSI_VERBOSE /* Define to enable verbose debug */
|
||||
|
||||
#ifdef SSI_DEBUG
|
||||
# define ssidbg lldbg
|
||||
# ifdef SSI_VERBOSE
|
||||
# define ssivdbg lldbg
|
||||
# else
|
||||
# define ssivdbg(x...)
|
||||
# endif
|
||||
#else
|
||||
# undef SSI_VERBOSE
|
||||
# define ssidbg(x...)
|
||||
# define ssivdbg(x...)
|
||||
#endif
|
||||
|
||||
/* Dump GPIO registers */
|
||||
|
||||
#ifdef SSI_VERBOSE
|
||||
# define ssi_dumpgpio(m) lm3s_dumpgpio(SDCCS_GPIO, m)
|
||||
#else
|
||||
# define ssi_dumpgpio(m)
|
||||
#endif
|
||||
|
||||
/************************************************************************************
|
||||
* Private Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: lm3s_ssiinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to configure SPI chip select GPIO pins for the LM3S8962 Eval Kit.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
void weak_function lm3s_ssiinitialize(void)
|
||||
{
|
||||
/* Configure the SPI-based microSD CS GPIO */
|
||||
|
||||
ssi_dumpgpio("lm3s_ssiinitialize() Entry)");
|
||||
lm3s_configgpio(SDCCS_GPIO);
|
||||
#ifdef CONFIG_NX_LCDDRIVER
|
||||
lm3s_configgpio(OLEDCS_GPIO);
|
||||
#endif
|
||||
ssi_dumpgpio("lm3s_ssiinitialize() Exit");
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* The external functions, lm3s_spiselect and lm3s_spistatus must be provided
|
||||
* by board-specific logic. The are implementations of the select and status
|
||||
* methods SPI interface defined by struct spi_ops_s (see include/nuttx/spi.h).
|
||||
* All othermethods (including up_spiinitialize()) are provided by common
|
||||
* logic. To use this common SPI logic on your board:
|
||||
*
|
||||
* 1. Provide lm3s_spiselect() and lm3s_spistatus() functions in your
|
||||
* board-specific logic. This function will perform chip selection and
|
||||
* status operations using GPIOs in the way your board is configured.
|
||||
* 2. Add a call to up_spiinitialize() in your low level initialization
|
||||
* logic
|
||||
* 3. The handle returned by up_spiinitialize() may then be used to bind the
|
||||
* SPI driver to higher level logic (e.g., calling
|
||||
* mmcsd_spislotinitialize(), for example, will bind the SPI driver to
|
||||
* the SPI MMC/SD driver).
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
void lm3s_spiselect(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
|
||||
{
|
||||
ssidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
|
||||
ssi_dumpgpio("lm3s_spiselect() Entry");
|
||||
|
||||
if (devid == SPIDEV_MMCSD)
|
||||
{
|
||||
/* Assert the CS pin to the card */
|
||||
|
||||
lm3s_gpiowrite(SDCCS_GPIO, !selected);
|
||||
}
|
||||
#ifdef CONFIG_NX_LCDDRIVER
|
||||
else if (devid == SPIDEV_DISPLAY)
|
||||
{
|
||||
/* Assert the CS pin to the display */
|
||||
|
||||
lm3s_gpiowrite(OLEDCS_GPIO, !selected);
|
||||
}
|
||||
#endif
|
||||
ssi_dumpgpio("lm3s_spiselect() Exit");
|
||||
}
|
||||
|
||||
uint8_t lm3s_spistatus(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
|
||||
{
|
||||
ssidbg("Returning SPI_STATUS_PRESENT\n");
|
||||
return SPI_STATUS_PRESENT;
|
||||
}
|
||||
|
||||
#endif /* !CONFIG_SSI0_DISABLE || !CONFIG_SSI1_DISABLE */
|
||||
Loading…
Reference in New Issue
Block a user