configs/lpcxpresso-lpc1768/nsh converted to use the kconfig-frontends tools

ChangeLog

@@ -6706,4 +6706,5 @@
           kconfig-frontends tools (2014-3-1).
 	* configs/lincoln60/nsh: Configuration converted to use the
           kconfig-frontends tools (2014-3-1).
-
+	* configs/lpcxpresso-lpc1768/nsh: Configuration converted to use the
+          kconfig-frontends tools (2014-3-1).

configs/lpcxpresso-lpc1768/README.txt

@@ -755,16 +755,28 @@ Where <subdir> is one of the following:
   nsh:
     Configures the NuttShell (nsh) located at apps/examples/nsh.  The
     Configuration enables both the serial and telnet NSH interfaces.
-    Support for the board's SPI-based MicroSD card is included
-    (but not passing tests as of this writing).
 
-    NOTE: At present, the value for the SD SPI frequency is too
-    high and the SD will fail.  Setting that frequency to 400000
-    removes the problem. TODO:  Tune this frequency to some optimal
-    value.
+    NOTES:
 
-    Jumpers: J55 must be set to provide chip select PIO1_11 signal as
-    the SD slot chip select.
+    1. This configuration uses the mconf-based configuration tool.  To
+       change this configurations using that tool, you should:
+
+       a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
+          and misc/tools/
+
+       b. Execute 'make menuconfig' in nuttx/ in order to start the
+          reconfiguration process.
+
+    2. This configuration has been used for testing the microSD card.
+       This support is, however, disabled in the base configuration.
+
+       At last attempt, the SPI-based mircroSD does not work at
+       higher fequencies.  Setting the SPI frequency to 400000
+       removes the problem.   There must be some more optimal
+       value that could be determined with additional experimetnation.
+
+       Jumpers: J55 must be set to provide chip select PIO1_11 signal as
+       the SD slot chip select.
 
   nx:
     And example using the NuttX graphics system (NX).  This example

configs/lpcxpresso-lpc1768/nsh/appconfig

@@ -1,58 +0,0 @@
-############################################################################
-# configs/lpcxpresso-lpc1768/nsh/appconfig
-#
-#   Copyright (C) 2011-2012 Gregory Nutt. All rights reserved.
-#   Author: Gregory Nutt <gnutt@nuttx.org>
-#
-# Redistribution and use in source and binary forms, with or without
-# modification, are permitted provided that the following conditions
-# are met:
-#
-# 1. Redistributions of source code must retain the above copyright
-#    notice, this list of conditions and the following disclaimer.
-# 2. Redistributions in binary form must reproduce the above copyright
-#    notice, this list of conditions and the following disclaimer in
-#    the documentation and/or other materials provided with the
-#    distribution.
-# 3. Neither the name NuttX nor the names of its contributors may be
-#    used to endorse or promote products derived from this software
-#    without specific prior written permission.
-#
-# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
-# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
-# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
-# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
-# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
-# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
-# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
-# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
-# POSSIBILITY OF SUCH DAMAGE.
-#
-############################################################################
-
-# Path to example in apps/examples containing the user_start entry point
-
-CONFIGURED_APPS += examples/nsh
-
-# NSH library
-
-CONFIGURED_APPS += system/readline
-CONFIGURED_APPS += nshlib
-
-# Networking support
-
-ifeq ($(CONFIG_NET),y)
-CONFIGURED_APPS += netutils/uiplib
-CONFIGURED_APPS += netutils/dhcpc
-CONFIGURED_APPS += netutils/resolv
-CONFIGURED_APPS += netutils/tftpc
-CONFIGURED_APPS += netutils/webclient
-ifeq ($(CONFIG_NSH_TELNET),y)
-CONFIGURED_APPS += netutils/telnetd
-endif
-endif
-
-