Nucleo-F401RE: Add standard, NuttX button support

configs/nucleo-f401re/README.txt

@@ -31,7 +31,6 @@ Contents
     - LED
     - Button
     - USARTS and Serial Consoles
-  - Buttons and LEDs
   - LQFP64
   - DFU and JTAG
   - Configurations
@@ -345,6 +344,8 @@ Hardware
 
   Buttons
   -------
+  B1 USER: the user button is connected to the I/O PC13 (pin 2) of the STM32
+  microcontroller.
 
   LEDs
   ----

configs/nucleo-f401re/include/board.h

@@ -328,6 +328,17 @@
 #define LED_ASSERTION    2
 #define LED_PANIC        1
 
+/* Buttons
+ *
+ * B1 USER: the user button is connected to the I/O PC13 (pin 2) of the STM32
+ * microcontroller.
+ */
+
+#define BUTTON_USER        0
+#define NUM_BUTTONS        1
+
+#define BUTTON_USER_BIT    (1 << BUTTON_USER)
+
 /************************************************************************************
  * Public Data
  ************************************************************************************/

configs/nucleo-f401re/src/Makefile

@@ -48,6 +48,10 @@ else
 CSRCS += stm32_userleds.c
 endif
 
+ifeq ($(CONFIG_ARCH_BUTTONS),y)
+CSRCS +=  stm32_buttons.c
+endif
+
 ifeq ($(CONFIG_WL_CC3000),y)
 CSRCS += stm32_wireless.c
 endif

configs/nucleo-f401re/src/nucleo-f401re.h

@@ -14,6 +14,28 @@
 #include <nuttx/compiler.h>
 #include <stdint.h>
 
+/* LED.  User LD2: the green LED is a user LED connected to Arduino signal D13
+ * corresponding to MCU I/O PA5 (pin 21) or PB13 (pin 34) depending on the STM32
+ * target.
+ *
+ * - When the I/O is HIGH value, the LED is on.
+ * - When the I/O is LOW, the LED is off.
+ */
+
+#define GPIO_LD2      (GPIO_PORTA | GPIO_PIN13 | GPIO_OUTPUT_CLEAR | GPIO_OUTPUT | GPIO_PULLUP | GPIO_SPEED_50MHz)
+
+/* Buttons
+ *
+ * B1 USER: the user button is connected to the I/O PC13 (pin 2) of the STM32
+ * microcontroller.
+ */
+
+#define MIN_IRQBUTTON   BUTTON_USER
+#define MAX_IRQBUTTON   BUTTON_USER
+#define NUM_IRQBUTTONS  1
+
+#define GPIO_BTN_USER   (GPIO_INPUT |GPIO_FLOAT |GPIO_EXTI | GPIO_PORTC | GPIO_PIN13)
+
 /* The shield uses the following pins:
  *
  *   +5V
@@ -27,21 +49,12 @@
  *   Digital pin 12:
  *   Digital pin 13:
  *   Even if optional 6-pin SPI header is used, these pins are unavailable for other use.
- *
- * LED.  User LD2: the green LED is a user LED connected to Arduino signal D13
- * corresponding to MCU I/O PA5 (pin 21) or PB13 (pin 34) depending on the STM32
- * target.
- *
- * - When the I/O is HIGH value, the LED is on.
- * - When the I/O is LOW, the LED is off.
  */
 
 #define GPIO_WIFI_INT (GPIO_PORTB | GPIO_PIN3  | GPIO_INPUT        | GPIO_PULLUP | GPIO_EXTI)
 #define GPIO_WIFI_EN  (GPIO_PORTB | GPIO_PIN4  | GPIO_OUTPUT_CLEAR | GPIO_OUTPUT | GPIO_PULLUP | GPIO_SPEED_50MHz)
 #define GPIO_WIFI_CS  (GPIO_PORTB | GPIO_PIN6  | GPIO_OUTPUT_SET   | GPIO_OUTPUT | GPIO_PULLUP | GPIO_SPEED_50MHz)
 
-#define GPIO_LD2      (GPIO_PORTA | GPIO_PIN13 | GPIO_OUTPUT_CLEAR | GPIO_OUTPUT | GPIO_PULLUP | GPIO_SPEED_50MHz)
-
 #if defined(CONFIG_CC3000_PROBES)
 #  define GPIO_D0     (GPIO_PORTB | GPIO_PIN7  | GPIO_OUTPUT_CLEAR | GPIO_OUTPUT | GPIO_PULLUP | GPIO_SPEED_50MHz)
 #  define GPIO_D1     (GPIO_PORTB | GPIO_PIN6  | GPIO_OUTPUT_CLEAR | GPIO_OUTPUT | GPIO_PULLUP | GPIO_SPEED_50MHz)

configs/nucleo-f401re/src/stm32_buttons.c

@@ -0,0 +1,137 @@
+/****************************************************************************
+ * configs/nucleo-f401re/src/stm32_buttons.c
+ *
+ *   Copyright (C) 2014 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+
+#include <nuttx/arch.h>
+#include <arch/board/board.h>
+
+#include "nucleo-f401re.h"
+
+#ifdef CONFIG_ARCH_BUTTONS
+
+/****************************************************************************
+ * Definitions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_button_initialize
+ *
+ * Description:
+ *   board_button_initialize() must be called to initialize button resources.
+ *   After that, board_buttons() may be called to collect the current state
+ *   of all buttons or board_button_irq() may be called to register button
+ *   interrupt handlers.
+ *
+ ****************************************************************************/
+
+void board_button_initialize(void)
+{
+  /* Configure the single button as an input.  NOTE that EXTI interrupts are
+   * also configured for the pin.
+   */
+
+  stm32_configgpio(GPIO_BTN_USER);
+}
+
+/****************************************************************************
+ * Name: board_buttons
+ ****************************************************************************/
+
+uint8_t board_buttons(void)
+{
+  /* Check that state of each USER button. A LOW value means that the key is
+   * pressed.
+   */
+
+  bool released = stm32_gpioread(GPIO_BTN_USER);
+  return !released;
+}
+
+/************************************************************************************
+ * Button support.
+ *
+ * Description:
+ *   board_button_initialize() must be called to initialize button resources.  After
+ *   that, board_buttons() may be called to collect the current state of all
+ *   buttons or board_button_irq() may be called to register button interrupt
+ *   handlers.
+ *
+ *   After board_button_initialize() has been called, board_buttons() may be called to
+ *   collect the state of all buttons.  board_buttons() returns an 8-bit bit set
+ *   with each bit associated with a button.  See the BUTTON_*_BIT
+ *   definitions in board.h for the meaning of each bit.
+ *
+ *   board_button_irq() may be called to register an interrupt handler that will
+ *   be called when a button is depressed or released.  The ID value is a
+ *   button enumeration value that uniquely identifies a button resource. See the
+ *   BUTTON_* definitions in board.h for the meaning of enumeration
+ *   value.  The previous interrupt handler address is returned (so that it may
+ *   restored, if so desired).
+ *
+ ************************************************************************************/
+
+#ifdef CONFIG_ARCH_IRQBUTTONS
+xcpt_t board_button_irq(int id, xcpt_t irqhandler)
+{
+  xcpt_t oldhandler = NULL;
+
+  if (id == BUTTON_USER)
+    {
+      oldhandler = stm32_gpiosetevent(GPIO_BTN_USER, true, true, true, irqhandler);
+    }
+
+  return oldhandler;
+}
+#endif
+#endif /* CONFIG_ARCH_BUTTONS */