diff --git a/configs/lpcxpresso-lpc1115/README.txt b/configs/lpcxpresso-lpc1115/README.txt
index a33a700cc7..60d1205e4c 100644
--- a/configs/lpcxpresso-lpc1115/README.txt
+++ b/configs/lpcxpresso-lpc1115/README.txt
@@ -13,6 +13,7 @@ Contents
   NuttX OABI "buildroot" Toolchain
   NXFLAT Toolchain
   Code Red IDE
+  Using OpenOCD
   LEDs
   LPCXpresso Configuration Options
   Configurations
@@ -330,6 +331,199 @@ NXFLAT Toolchain
   8. Edit setenv.h, if necessary, so that the PATH variable includes
      the path to the newly builtNXFLAT binaries.
 
+Using OpenOCD
+^^^^^^^^^^^^^
+
+  https://acassis.wordpress.com/2015/03/29/using-openocd-to-program-the-lpc1115-lpcxpresso-board/
+
+  Using OpenOCD to program the LPC1115 LPCXpresso board
+  March 29, 2015 by acassis
+
+  Unfortunately NXP uses a built-in programmer in the LPCXpresso board
+  called LPCLink that is not supported by OpenOCD and there is not (AFAIK)
+  an option to replace its firmware.
+
+  Then I decided to cut the board to separate the “LPCXpresso LPC1115 REV A”
+  from the LPCLink programmer.
+
+  So I used a simple and low cost STLink-v2 programmer board that is
+  supported by OpenOCD. In order to use OpenOCD to reprogram the LPC1115
+  board we need to connect four wires from STLink-v2 to LPC1115 board:
+
+    STLink-v2    |   LPC1115 Board
+    ------------------------------
+    GND              GND
+    3V3              3V3
+    IO               AD4
+    CLK              P0.10
+
+
+  Also we need to instruct OpenOCD to use SWD protocol. You can do it
+  creating the following config openocd.cfg file:
+
+    # LPC1115 LPCXpresso Target
+
+    # Using stlink as SWD programmer
+    source [find interface/stlink-v2.cfg]
+
+    # SWD as transport
+    transport select hla_swd
+
+    # Use LPC1115 target
+    set WORKAREASIZE 0x4000
+    source [find target/lpc11xx.cfg]
+
+  Now execute OpenOCD using the created config file:
+
+    $ sudo openocd -f openocd.cfg
+    Open On-Chip Debugger 0.9.0-dev-00251-g1fa4c72 (2015-01-28-20:08)
+    Licensed under GNU GPL v2
+    For bug reports, read
+        http://openocd.sourceforge.net/doc/doxygen/bugs.html
+    Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
+    adapter speed: 10 kHz
+    adapter_nsrst_delay: 200
+    Info : Unable to match requested speed 10 kHz, using 5 kHz
+    Info : Unable to match requested speed 10 kHz, using 5 kHz
+    Info : clock speed 5 kHz
+    Info : STLINK v2 JTAG v17 API v2 SWIM v4 VID 0x0483 PID 0x3748
+    Info : using stlink api v2
+    Info : Target voltage: 3.137636
+    Info : lpc11xx.cpu: hardware has 4 breakpoints, 2 watchpoints
+
+  Connect to OpenOCD server:
+
+    $ telnet 127.0.0.1 4444
+
+    Reset the CPU and flash the lpc1115_blink.bin file:
+
+      > reset halt
+    target state: halted
+    target halted due to debug-request, current mode: Thread
+    xPSR: 0xc1000000 pc: 0x1fff0040 msp: 0x10000ffc
+
+    > flash probe 0
+    flash 'lpc2000' found at 0x00000000
+
+    > flash write_image erase blink_lpc1115.bin 0x00000000
+    auto erase enabled
+    target state: halted
+    target halted due to breakpoint, current mode: Thread
+    xPSR: 0x01000000 pc: 0x10000108 msp: 0x100001b8
+    Verification will fail since checksum in image (0x00000000) to be written to flash is different from calculated vector checksum (0xefffebe9).
+    To remove this warning modify build tools on developer PC to inject correct LPC vector checksum.
+    wrote 4096 bytes from file blink_lpc1115.bin in 0.592621s (6.750 KiB/s)
+
+    > reset run
+
+  The checksum warning message could be removed if you add the checksum to
+  binary, read this post:
+
+    http://sigalrm.blogspot.com.br/2011/10/cortex-m3-exception-vector-checksum.html.
+
+  The blink LED sample I got from Frank Duignan’s page:
+
+    http://eleceng.dit.ie/frank/arm/BareMetalLPC1114/index.html
+
+  Edit Makefile and configure LIBSPEC to point out to the right path:
+
+     LIBSPEC=-L /usr/lib/gcc/arm-none-eabi/4.8/armv6-m
+
+  $ make
+
+  To generate the final binary I used objcopy:
+
+  $ arm-none-eabi-objcopy -O binary main.elf blink_lpc1115.bin
+
+  https://acassis.wordpress.com/2015/05/22/using-openocd-and-gdb-to-debug-my-nuttx-port-to-lpc11xx/
+
+  Using OpenOCD and gdb to debug my NuttX port to LPC11xx
+  May 22, 2015 by acassis
+
+  I’m porting NuttX to LPC11xx (using the LPCXpresso LPC1115 board) and
+  these are the steps I used to get OpenOCD and GDB working to debug my firmware:
+
+  The openocd.cfg to use with STLink-v2 SWD programmer:
+
+    # LPC1115 LPCXpresso Target
+
+    # Using stlink as SWD programmer
+    source [find interface/stlink-v2.cfg]
+
+    # SWD as transport
+    transport select hla_swd
+
+    # Use LPC1115 target
+    set WORKAREASIZE 0x4000
+    source [find target/lpc11xx.cfg]
+
+  You need to execute “reset halt” from OpenOCD telnet server to get
+  “monitor reset halt” working on gdb:
+
+    $ telnet 127.0.0.1 4444Trying 127.0.0.1...
+    Connected to 127.0.0.1.
+    Escape character is '^]'.
+    Open On-Chip Debugger
+
+    > reset halt
+    target state: halted
+    target halted due to debug-request, current mode: Thread
+    xPSR: 0xc1000000 pc: 0x1fff0040 msp: 0x10000ffc
+
+    > exit
+
+  Now execute the command arm-none-eabi-gdb (from Debian/Ubuntu package
+  “gdb-arm-none-eabi”) passing the nuttx ELF file:
+
+    $ arm-none-eabi-gdb nuttx
+    GNU gdb (7.7.1+dfsg-1+6) 7.7.1
+    Reading symbols from nuttx...done.
+
+    (gdb) target remote localhost:3333
+    Remote debugging using localhost:3333
+    0x1fff0040 in ?? ()
+
+    (gdb) monitor reset halt
+    target state: halted
+    target halted due to debug-request, current mode: Thread
+    xPSR: 0xc1000000 pc: 0x1fff0040 msp: 0x10000ffc
+
+    (gdb) load
+    Loading section .vectors, size 0xc0 lma 0x0
+    Loading section .text, size 0x9197 lma 0x410
+    Loading section .ARM.exidx, size 0x8 lma 0x95a8
+    Loading section .data, size 0x48 lma 0x95b0
+    Start address 0x410, load size 37543
+    Transfer rate: 9 KB/sec, 6257 bytes/write.
+
+    (gdb) b __start
+    Breakpoint 1 at 0x410: file chip/lpc11_start.c, line 109.
+
+    (gdb) step
+
+    Note: automatically using hardware breakpoints for read-only addresses.
+
+    Breakpoint 1, __start () at chip/lpc11_start.c:109
+    109	{
+
+    (gdb)
+    115	  lpc11_clockconfig();
+
+    (gdb)
+    lpc11_clockconfig () at chip/lpc11_clockconfig.c:93
+    93	  putreg32(SYSCON_SYSPLLCLKSEL_IRCOSC, LPC11_SYSCON_SYSPLLCLKSEL);
+
+    (gdb)
+    96	  putreg32((SYSCON_SYSPLLCTRL_MSEL_DIV(4) | SYSCON_SYSPLLCTRL_PSEL_DIV2), LPC11_SYSCON_SYSPLLCTRL);
+
+    (gdb) p /x *0x40048008      <--- this is the LPC11_SYSCON_SYSPLLCTRL register address
+    $2 = 0x23
+    (gdb)
+
+    You can use breakpoints, steps and many other GDB features.
+
+    That is it!
+
 LEDs
 ^^^^
 
@@ -491,26 +685,57 @@ selected as follow:
 
 Where <subdir> is one of the following:
 
-  dhcpd:
-    This builds the DCHP server using the apps/examples/dhcpd application
-    (for execution from FLASH.) See apps/examples/README.txt for information
-    about the dhcpd example.
+  minnsh:
+  ------
 
-    NOTES:
+    This is a experiment to see just how small we can get a usable NSH
+    configuration.  This configuration has far fewer features than the nsh
+    configuration but is also a fraction of the size.
 
-    1. This configuration uses the mconf-based configuration tool.  To
-       change this configurations using that tool, you should:
+    STATUS:
+    2015-5-23
+      The nuttx.bin minnsh firmware file size:
 
-       a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
-          and misc/tools/
+    $ ls -l nuttx.bin
+    -rwxr-xr-x 1 alan alan 17409 May 23 11:01 nuttx.bin
 
-       b. Execute 'make menuconfig' in nuttx/ in order to start the
-          reconfiguration process.
+    $ arm-none-eabi-size nuttx
+    text data bss dec hex filename
+    16367 193 704 17264 4370 nuttx
 
-    2. Jumpers: Nothing special.  Use the default base board jumper
-       settings.
+    This is serial console output (and input) :
+
+    NuttShell (NSH)
+    nsh> ls /dev
+    nsh: ls: command not found
+
+    No filesystem, no "ls" command :-)
+
+    nsh> ?
+    help usage: help [-v] [<cmd>]
+
+    ? exec free mb mw xd
+    echo exit help mh ps
+    nsh> free
+    total used free largest
+    Mem: 6464 1816 4648 4648
+
+    nsh> echo "NuttX is magic!"
+    NuttX is magic!
+    nsh>
+
+    Replace NSH with apps/examples/hello:
+
+    $ ls -l nuttx.bin
+    -rwxr-xr-x 1 alan alan 12873 May 23 11:05 nuttx.bin
+
+    $ arm-none-eabi-size nuttx
+    text data bss dec hex filename
+    11829 193 704 12726 31b6 nuttx
 
   nsh:
+  ---
+
     Configures the NuttShell (nsh) located at apps/examples/nsh.  The
     Configuration enables both the serial and telnet NSH interfaces.
 
@@ -535,19 +760,3 @@ Where <subdir> is one of the following:
 
        Jumpers: J55 must be set to provide chip select PIO1_11 signal as
        the SD slot chip select.
-
-  nx:
-    And example using the NuttX graphics system (NX).  This example
-    uses the UG-9664HSWAG01 driver.
-
-    NOTES:
-
-    1. This configuration uses the mconf-based configuration tool.  To
-       change this configurations using that tool, you should:
-
-       a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
-          and misc/tools/
-
-       b. Execute 'make menuconfig' in nuttx/ in order to start the
-          reconfiguration process.
-
diff --git a/configs/lpcxpresso-lpc1115/minnsh/Make.defs b/configs/lpcxpresso-lpc1115/minnsh/Make.defs
new file mode 100644
index 0000000000..def68d488a
--- /dev/null
+++ b/configs/lpcxpresso-lpc1115/minnsh/Make.defs
@@ -0,0 +1,122 @@
+############################################################################
+# configs/lpcxpresso-lpc1115/minnsh/Make.defs
+#
+#   Copyright (C) 2015 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+include ${TOPDIR}/tools/Config.mk
+include ${TOPDIR}/arch/arm/src/armv6-m/Toolchain.defs
+
+LDSCRIPT = ld.script
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)}"
+else
+  # Linux/Cygwin-native toolchain
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(ARCROSSDEV)ar rcs
+NM = $(ARCROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  ARCHOPTIMIZATION = -g
+endif
+
+ifneq ($(CONFIG_DEBUG_NOOPT),y)
+  ARCHOPTIMIZATION += $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions -fno-rtti
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-pcrel.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-nuttx-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+ifeq ($(CONFIG_HOST_WINDOWS),y)
+  HOSTEXEEXT = .exe
+else
+  HOSTEXEEXT =
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native host tools
+  DIRLINK = $(TOPDIR)/tools/copydir.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+else
+  # Linux/Cygwin-native host tools
+  MKDEP = $(TOPDIR)/tools/mkdeps$(HOSTEXEEXT)
+endif
diff --git a/configs/lpcxpresso-lpc1115/minnsh/defconfig b/configs/lpcxpresso-lpc1115/minnsh/defconfig
new file mode 100644
index 0000000000..d2d4c13314
--- /dev/null
+++ b/configs/lpcxpresso-lpc1115/minnsh/defconfig
@@ -0,0 +1,710 @@
+#
+# Automatically generated file; DO NOT EDIT.
+# Nuttx/ Configuration
+#
+
+#
+# Build Setup
+#
+# CONFIG_EXPERIMENTAL is not set
+CONFIG_DEFAULT_SMALL=y
+CONFIG_HOST_LINUX=y
+# CONFIG_HOST_OSX is not set
+# CONFIG_HOST_WINDOWS is not set
+# CONFIG_HOST_OTHER is not set
+
+#
+# Build Configuration
+#
+# CONFIG_APPS_DIR="../apps"
+CONFIG_BUILD_FLAT=y
+# CONFIG_BUILD_2PASS is not set
+
+#
+# Binary Output Formats
+#
+# CONFIG_RRLOAD_BINARY is not set
+# CONFIG_INTELHEX_BINARY is not set
+# CONFIG_MOTOROLA_SREC is not set
+CONFIG_RAW_BINARY=y
+# CONFIG_UBOOT_UIMAGE is not set
+
+#
+# Customize Header Files
+#
+# CONFIG_ARCH_STDINT_H is not set
+# CONFIG_ARCH_STDBOOL_H is not set
+# CONFIG_ARCH_MATH_H is not set
+# CONFIG_ARCH_FLOAT_H is not set
+# CONFIG_ARCH_STDARG_H is not set
+
+#
+# Debug Options
+#
+# CONFIG_DEBUG is not set
+# CONFIG_ARCH_HAVE_HEAPCHECK is not set
+CONFIG_ARCH_HAVE_STACKCHECK=y
+# CONFIG_STACK_COLORATION is not set
+# CONFIG_DEBUG_SYMBOLS is not set
+CONFIG_ARCH_HAVE_CUSTOMOPT=y
+# CONFIG_DEBUG_NOOPT is not set
+# CONFIG_DEBUG_CUSTOMOPT is not set
+CONFIG_DEBUG_FULLOPT=y
+
+#
+# System Type
+#
+CONFIG_ARCH_ARM=y
+# CONFIG_ARCH_AVR is not set
+# CONFIG_ARCH_HC is not set
+# CONFIG_ARCH_MIPS is not set
+# CONFIG_ARCH_RGMP is not set
+# CONFIG_ARCH_SH is not set
+# CONFIG_ARCH_SIM is not set
+# CONFIG_ARCH_X86 is not set
+# CONFIG_ARCH_Z16 is not set
+# CONFIG_ARCH_Z80 is not set
+CONFIG_ARCH="arm"
+
+#
+# ARM Options
+#
+# CONFIG_ARCH_CHIP_A1X is not set
+# CONFIG_ARCH_CHIP_C5471 is not set
+# CONFIG_ARCH_CHIP_CALYPSO is not set
+# CONFIG_ARCH_CHIP_DM320 is not set
+# CONFIG_ARCH_CHIP_EFM32 is not set
+# CONFIG_ARCH_CHIP_IMX is not set
+# CONFIG_ARCH_CHIP_KINETIS is not set
+# CONFIG_ARCH_CHIP_KL is not set
+# CONFIG_ARCH_CHIP_LM is not set
+# CONFIG_ARCH_CHIP_TIVA is not set
+CONFIG_ARCH_CHIP_LPC11XX=y
+# CONFIG_ARCH_CHIP_LPC17XX is not set
+# CONFIG_ARCH_CHIP_LPC214X is not set
+# CONFIG_ARCH_CHIP_LPC2378 is not set
+# CONFIG_ARCH_CHIP_LPC31XX is not set
+# CONFIG_ARCH_CHIP_LPC43XX is not set
+# CONFIG_ARCH_CHIP_NUC1XX is not set
+# CONFIG_ARCH_CHIP_SAMA5 is not set
+# CONFIG_ARCH_CHIP_SAMD is not set
+# CONFIG_ARCH_CHIP_SAML is not set
+# CONFIG_ARCH_CHIP_SAM34 is not set
+# CONFIG_ARCH_CHIP_SAMV7 is not set
+# CONFIG_ARCH_CHIP_STM32 is not set
+# CONFIG_ARCH_CHIP_STR71X is not set
+# CONFIG_ARCH_ARM7TDMI is not set
+# CONFIG_ARCH_ARM926EJS is not set
+# CONFIG_ARCH_ARM920T is not set
+CONFIG_ARCH_CORTEXM0=y
+# CONFIG_ARCH_CORTEXM3 is not set
+# CONFIG_ARCH_CORTEXM4 is not set
+# CONFIG_ARCH_CORTEXM7 is not set
+# CONFIG_ARCH_CORTEXA5 is not set
+# CONFIG_ARCH_CORTEXA8 is not set
+CONFIG_ARCH_FAMILY="armv6-m"
+CONFIG_ARCH_CHIP="lpc11xx"
+CONFIG_ARCH_HAVE_CMNVECTOR=y
+# CONFIG_ARMV7M_CMNVECTOR is not set
+# CONFIG_ARMV7M_LAZYFPU is not set
+# CONFIG_ARCH_HAVE_FPU is not set
+# CONFIG_ARCH_HAVE_DPFPU is not set
+
+#
+# ARMV6M Configuration Options
+#
+# CONFIG_ARMV6M_TOOLCHAIN_BUILDROOT is not set
+# CONFIG_ARMV6M_TOOLCHAIN_CODEREDL is not set
+# CONFIG_ARMV6M_TOOLCHAIN_CODESOURCERYL is not set
+CONFIG_ARMV6M_TOOLCHAIN_GNU_EABIL=y
+# CONFIG_GPIO_IRQ is not set
+
+#
+# LPC11xx Configuration Options
+#
+# CONFIG_ARCH_CHIP_LPC1114 is not set
+CONFIG_ARCH_CHIP_LPC1115=y
+CONFIG_ARCH_FAMILY_LPC111X=y
+
+#
+# LPC11xx Peripheral Support
+#
+CONFIG_LPC11_INTRCOSC=y
+# CONFIG_LPC11_MAINOSC is not set
+CONFIG_LPC11_SYSTICK_CORECLK=y
+# CONFIG_LPC11_SYSTICK_CORECLK_DIV16 is not set
+CONFIG_LPC11_PLL=y
+CONFIG_LPC11_UART0=y
+# CONFIG_LPC11_CAN0 is not set
+# CONFIG_LPC11_SPI is not set
+# CONFIG_LPC11_SSP0 is not set
+# CONFIG_LPC11_SSP1 is not set
+# CONFIG_LPC11_I2C0 is not set
+# CONFIG_LPC11_TMR0 is not set
+# CONFIG_LPC11_TMR1 is not set
+# CONFIG_LPC11_WDT is not set
+# CONFIG_LPC11_ADC is not set
+# CONFIG_LPC11_FLASH is not set
+
+#
+# Serial driver options
+#
+# CONFIG_SERIAL_TERMIOS is not set
+
+#
+# Architecture Options
+#
+# CONFIG_ARCH_NOINTC is not set
+# CONFIG_ARCH_VECNOTIRQ is not set
+# CONFIG_ARCH_DMA is not set
+CONFIG_ARCH_HAVE_IRQPRIO=y
+# CONFIG_ARCH_L2CACHE is not set
+# CONFIG_ARCH_HAVE_COHERENT_DCACHE is not set
+# CONFIG_ARCH_HAVE_ADDRENV is not set
+# CONFIG_ARCH_NEED_ADDRENV_MAPPING is not set
+CONFIG_ARCH_HAVE_VFORK=y
+# CONFIG_ARCH_HAVE_MMU is not set
+# CONFIG_ARCH_HAVE_MPU is not set
+# CONFIG_ARCH_NAND_HWECC is not set
+# CONFIG_ARCH_HAVE_EXTCLK is not set
+# CONFIG_ARCH_IRQPRIO is not set
+CONFIG_ARCH_STACKDUMP=y
+# CONFIG_ENDIAN_BIG is not set
+# CONFIG_ARCH_IDLE_CUSTOM is not set
+# CONFIG_ARCH_HAVE_RAMFUNCS is not set
+# CONFIG_ARCH_HAVE_RAMVECTORS is not set
+
+#
+# Board Settings
+#
+CONFIG_BOARD_LOOPSPERMSEC=2988
+# CONFIG_ARCH_CALIBRATION is not set
+
+#
+# Interrupt options
+#
+CONFIG_ARCH_HAVE_INTERRUPTSTACK=y
+CONFIG_ARCH_INTERRUPTSTACK=0
+# CONFIG_ARCH_HAVE_HIPRI_INTERRUPT is not set
+
+#
+# Boot options
+#
+# CONFIG_BOOT_RUNFROMEXTSRAM is not set
+CONFIG_BOOT_RUNFROMFLASH=y
+# CONFIG_BOOT_RUNFROMISRAM is not set
+# CONFIG_BOOT_RUNFROMSDRAM is not set
+# CONFIG_BOOT_COPYTORAM is not set
+
+#
+# Boot Memory Configuration
+#
+CONFIG_RAM_START=0x10000000
+CONFIG_RAM_SIZE=8192
+# CONFIG_ARCH_HAVE_SDRAM is not set
+
+#
+# Board Selection
+#
+CONFIG_ARCH_BOARD_LPCXPRESSO_LPC1115=y
+# CONFIG_ARCH_BOARD_CUSTOM is not set
+CONFIG_ARCH_BOARD="lpcxpresso-lpc1115"
+
+#
+# Common Board Options
+#
+CONFIG_ARCH_HAVE_LEDS=y
+CONFIG_ARCH_LEDS=y
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Board-Specific Options
+#
+# CONFIG_LIB_BOARDCTL is not set
+
+#
+# RTOS Features
+#
+CONFIG_DISABLE_OS_API=y
+CONFIG_DISABLE_POSIX_TIMERS=y
+CONFIG_DISABLE_PTHREAD=y
+CONFIG_DISABLE_SIGNALS=y
+CONFIG_DISABLE_MQUEUE=y
+CONFIG_DISABLE_ENVIRON=y
+
+#
+# Clocks and Timers
+#
+CONFIG_USEC_PER_TICK=10000
+# CONFIG_SYSTEM_TIME64 is not set
+# CONFIG_CLOCK_MONOTONIC is not set
+# CONFIG_JULIAN_TIME is not set
+CONFIG_START_YEAR=2013
+CONFIG_START_MONTH=2
+CONFIG_START_DAY=26
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_WDOG_INTRESERVE=0
+CONFIG_PREALLOC_TIMERS=0
+
+#
+# Tasks and Scheduling
+#
+# CONFIG_INIT_NONE is not set
+CONFIG_INIT_ENTRYPOINT=y
+# CONFIG_INIT_FILEPATH is not set
+CONFIG_USER_ENTRYPOINT="nsh_main"
+CONFIG_RR_INTERVAL=0
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_MAX_TASKS=4
+# CONFIG_SCHED_HAVE_PARENT is not set
+# CONFIG_SCHED_WAITPID is not set
+
+#
+# Performance Monitoring
+#
+# CONFIG_SCHED_CPULOAD is not set
+# CONFIG_SCHED_INSTRUMENTATION is not set
+
+#
+# Files and I/O
+#
+# CONFIG_DEV_CONSOLE is not set
+CONFIG_FDCLONE_DISABLE=y
+# CONFIG_FDCLONE_STDIO is not set
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_NFILE_DESCRIPTORS=0
+CONFIG_NFILE_STREAMS=0
+CONFIG_NAME_MAX=32
+# CONFIG_PRIORITY_INHERITANCE is not set
+
+#
+# RTOS hooks
+#
+# CONFIG_BOARD_INITIALIZE is not set
+# CONFIG_SCHED_STARTHOOK is not set
+# CONFIG_SCHED_ATEXIT is not set
+# CONFIG_SCHED_ONEXIT is not set
+
+#
+# Work Queue Support
+#
+
+#
+# Stack and heap information
+#
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=1536
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=1536
+# CONFIG_LIB_SYSCALL is not set
+
+#
+# Device Drivers
+#
+CONFIG_DISABLE_POLL=y
+# CONFIG_DEV_NULL is not set
+# CONFIG_DEV_ZERO is not set
+# CONFIG_LOOP is not set
+
+#
+# Buffering
+#
+# CONFIG_DRVR_WRITEBUFFER is not set
+# CONFIG_DRVR_READAHEAD is not set
+# CONFIG_RAMDISK is not set
+# CONFIG_CAN is not set
+# CONFIG_ARCH_HAVE_PWM_PULSECOUNT is not set
+# CONFIG_PWM is not set
+# CONFIG_ARCH_HAVE_I2CRESET is not set
+# CONFIG_I2C is not set
+# CONFIG_SPI is not set
+# CONFIG_I2S is not set
+
+#
+# Timer Driver Support
+#
+# CONFIG_TIMER is not set
+# CONFIG_RTC is not set
+# CONFIG_WATCHDOG is not set
+# CONFIG_ANALOG is not set
+# CONFIG_AUDIO_DEVICES is not set
+# CONFIG_VIDEO_DEVICES is not set
+# CONFIG_BCH is not set
+# CONFIG_INPUT is not set
+# CONFIG_LCD is not set
+# CONFIG_MMCSD is not set
+# CONFIG_MTD is not set
+# CONFIG_EEPROM is not set
+# CONFIG_PIPES is not set
+# CONFIG_PM is not set
+# CONFIG_POWER is not set
+# CONFIG_SENSORS is not set
+# CONFIG_SERCOMM_CONSOLE is not set
+CONFIG_SERIAL=y
+# CONFIG_16550_UART is not set
+# CONFIG_ARCH_HAVE_UART is not set
+CONFIG_ARCH_HAVE_UART0=y
+# CONFIG_ARCH_HAVE_UART1 is not set
+# CONFIG_ARCH_HAVE_UART2 is not set
+# CONFIG_ARCH_HAVE_UART3 is not set
+# CONFIG_ARCH_HAVE_UART4 is not set
+# CONFIG_ARCH_HAVE_UART5 is not set
+# CONFIG_ARCH_HAVE_UART6 is not set
+# CONFIG_ARCH_HAVE_UART7 is not set
+# CONFIG_ARCH_HAVE_UART8 is not set
+# CONFIG_ARCH_HAVE_SCI0 is not set
+# CONFIG_ARCH_HAVE_SCI1 is not set
+# CONFIG_ARCH_HAVE_USART0 is not set
+# CONFIG_ARCH_HAVE_USART1 is not set
+# CONFIG_ARCH_HAVE_USART2 is not set
+# CONFIG_ARCH_HAVE_USART3 is not set
+# CONFIG_ARCH_HAVE_USART4 is not set
+# CONFIG_ARCH_HAVE_USART5 is not set
+# CONFIG_ARCH_HAVE_USART6 is not set
+# CONFIG_ARCH_HAVE_USART7 is not set
+# CONFIG_ARCH_HAVE_USART8 is not set
+# CONFIG_ARCH_HAVE_OTHER_UART is not set
+
+#
+# USART Configuration
+#
+CONFIG_MCU_SERIAL=y
+# CONFIG_STANDARD_SERIAL is not set
+# CONFIG_SERIAL_IFLOWCONTROL is not set
+# CONFIG_SERIAL_OFLOWCONTROL is not set
+# CONFIG_ARCH_HAVE_SERIAL_TERMIOS is not set
+CONFIG_UART0_SERIAL_CONSOLE=y
+# CONFIG_OTHER_SERIAL_CONSOLE is not set
+# CONFIG_NO_SERIAL_CONSOLE is not set
+
+#
+# UART0 Configuration
+#
+CONFIG_UART0_RXBUFSIZE=64
+CONFIG_UART0_TXBUFSIZE=64
+CONFIG_UART0_BAUD=115200
+CONFIG_UART0_BITS=8
+CONFIG_UART0_PARITY=0
+CONFIG_UART0_2STOP=0
+# CONFIG_UART0_IFLOWCONTROL is not set
+# CONFIG_UART0_OFLOWCONTROL is not set
+# CONFIG_USBDEV is not set
+# CONFIG_USBHOST is not set
+# CONFIG_WIRELESS is not set
+
+#
+# System Logging Device Options
+#
+
+#
+# System Logging
+#
+# CONFIG_RAMLOG is not set
+
+#
+# Networking Support
+#
+# CONFIG_ARCH_HAVE_NET is not set
+# CONFIG_ARCH_HAVE_PHY is not set
+# CONFIG_NET is not set
+
+#
+# Crypto API
+#
+# CONFIG_CRYPTO is not set
+
+#
+# File Systems
+#
+
+#
+# File system configuration
+#
+CONFIG_DISABLE_MOUNTPOINT=y
+CONFIG_DISABLE_PSEUDOFS_OPERATIONS=y
+# CONFIG_FS_READABLE is not set
+# CONFIG_FS_WRITABLE is not set
+# CONFIG_FS_NAMED_SEMAPHORES is not set
+# CONFIG_FS_RAMMAP is not set
+# CONFIG_FS_PROCFS is not set
+
+#
+# System Logging
+#
+# CONFIG_SYSLOG is not set
+# CONFIG_SYSLOG_TIMESTAMP is not set
+
+#
+# Graphics Support
+#
+# CONFIG_NX is not set
+
+#
+# Memory Management
+#
+CONFIG_MM_SMALL=y
+CONFIG_MM_REGIONS=1
+# CONFIG_ARCH_HAVE_HEAP2 is not set
+# CONFIG_GRAN is not set
+
+#
+# Audio Support
+#
+# CONFIG_AUDIO is not set
+
+#
+# Binary Loader
+#
+# CONFIG_BINFMT_DISABLE is not set
+# CONFIG_NXFLAT is not set
+# CONFIG_ELF is not set
+# CONFIG_BUILTIN is not set
+# CONFIG_PIC is not set
+# CONFIG_SYMTAB_ORDEREDBYNAME is not set
+
+#
+# Library Routines
+#
+
+#
+# Standard C Library Options
+#
+CONFIG_STDIO_BUFFER_SIZE=0
+CONFIG_STDIO_LINEBUFFER=y
+CONFIG_NUNGET_CHARS=0
+# CONFIG_LIBM is not set
+CONFIG_NOPRINTF_FIELDWIDTH=y
+# CONFIG_LIBC_FLOATINGPOINT is not set
+# CONFIG_LIBC_IOCTL_VARIADIC is not set
+CONFIG_LIB_RAND_ORDER=1
+# CONFIG_EOL_IS_CR is not set
+# CONFIG_EOL_IS_LF is not set
+# CONFIG_EOL_IS_BOTH_CRLF is not set
+CONFIG_EOL_IS_EITHER_CRLF=y
+# CONFIG_LIBC_EXECFUNCS is not set
+CONFIG_POSIX_SPAWN_PROXY_STACKSIZE=1024
+CONFIG_TASK_SPAWN_DEFAULT_STACKSIZE=1536
+# CONFIG_LIBC_STRERROR is not set
+# CONFIG_LIBC_PERROR_STDOUT is not set
+CONFIG_ARCH_LOWPUTC=y
+# CONFIG_TIME_EXTENDED is not set
+CONFIG_LIB_SENDFILE_BUFSIZE=512
+# CONFIG_ARCH_ROMGETC is not set
+# CONFIG_ARCH_OPTIMIZED_FUNCTIONS is not set
+
+#
+# Non-standard Library Support
+#
+# CONFIG_LIB_KBDCODEC is not set
+# CONFIG_LIB_SLCDCODEC is not set
+
+#
+# Basic CXX Support
+#
+# CONFIG_C99_BOOL8 is not set
+# CONFIG_HAVE_CXX is not set
+
+#
+# Application Configuration
+#
+
+#
+# Built-In Applications
+#
+
+#
+# Examples
+#
+# CONFIG_EXAMPLES_BUTTONS is not set
+# CONFIG_EXAMPLES_CAN is not set
+# CONFIG_EXAMPLES_CONFIGDATA is not set
+# CONFIG_EXAMPLES_CPUHOG is not set
+# CONFIG_EXAMPLES_DHCPD is not set
+# CONFIG_EXAMPLES_ELF is not set
+# CONFIG_EXAMPLES_FTPC is not set
+# CONFIG_EXAMPLES_FTPD is not set
+# CONFIG_EXAMPLES_HELLO is not set
+# CONFIG_EXAMPLES_HELLOXX is not set
+# CONFIG_EXAMPLES_JSON is not set
+# CONFIG_EXAMPLES_HIDKBD is not set
+# CONFIG_EXAMPLES_KEYPADTEST is not set
+# CONFIG_EXAMPLES_IGMP is not set
+# CONFIG_EXAMPLES_MM is not set
+# CONFIG_EXAMPLES_MODBUS is not set
+# CONFIG_EXAMPLES_MOUNT is not set
+# CONFIG_EXAMPLES_NRF24L01TERM is not set
+CONFIG_EXAMPLES_NSH=y
+# CONFIG_EXAMPLES_NULL is not set
+# CONFIG_EXAMPLES_NX is not set
+# CONFIG_EXAMPLES_NXTERM is not set
+# CONFIG_EXAMPLES_NXFFS is not set
+# CONFIG_EXAMPLES_NXFLAT is not set
+# CONFIG_EXAMPLES_NXHELLO is not set
+# CONFIG_EXAMPLES_NXIMAGE is not set
+# CONFIG_EXAMPLES_NXLINES is not set
+# CONFIG_EXAMPLES_NXTEXT is not set
+# CONFIG_EXAMPLES_OSTEST is not set
+# CONFIG_EXAMPLES_PIPE is not set
+# CONFIG_EXAMPLES_POLL is not set
+# CONFIG_EXAMPLES_PPPD is not set
+# CONFIG_EXAMPLES_POSIXSPAWN is not set
+# CONFIG_EXAMPLES_QENCODER is not set
+# CONFIG_EXAMPLES_RGMP is not set
+# CONFIG_EXAMPLES_SENDMAIL is not set
+# CONFIG_EXAMPLES_SERIALBLASTER is not set
+# CONFIG_EXAMPLES_SERIALRX is not set
+# CONFIG_EXAMPLES_SERLOOP is not set
+# CONFIG_EXAMPLES_SLCD is not set
+# CONFIG_EXAMPLES_SMART is not set
+# CONFIG_EXAMPLES_TCPECHO is not set
+# CONFIG_EXAMPLES_TELNETD is not set
+# CONFIG_EXAMPLES_THTTPD is not set
+# CONFIG_EXAMPLES_TIFF is not set
+# CONFIG_EXAMPLES_TOUCHSCREEN is not set
+# CONFIG_EXAMPLES_WEBSERVER is not set
+# CONFIG_EXAMPLES_USBSERIAL is not set
+# CONFIG_EXAMPLES_USBTERM is not set
+# CONFIG_EXAMPLES_WATCHDOG is not set
+
+#
+# Graphics Support
+#
+# CONFIG_TIFF is not set
+# CONFIG_GRAPHICS_TRAVELER is not set
+
+#
+# Interpreters
+#
+# CONFIG_INTERPRETERS_FICL is not set
+# CONFIG_INTERPRETERS_PCODE is not set
+# CONFIG_INTERPRETERS_MICROPYTHON is not set
+
+#
+# Network Utilities
+#
+
+#
+# Networking Utilities
+#
+# CONFIG_NETUTILS_CODECS is not set
+# CONFIG_NETUTILS_FTPC is not set
+# CONFIG_NETUTILS_JSON is not set
+# CONFIG_NETUTILS_SMTP is not set
+# CONFIG_NETUTILS_THTTPD is not set
+
+#
+# FreeModBus
+#
+# CONFIG_MODBUS is not set
+
+#
+# NSH Library
+#
+CONFIG_NSH_LIBRARY=y
+
+#
+# Command Line Configuration
+#
+CONFIG_NSH_READLINE=y
+# CONFIG_NSH_CLE is not set
+CONFIG_NSH_LINELEN=80
+CONFIG_NSH_DISABLE_SEMICOLON=y
+CONFIG_NSH_MAXARGUMENTS=6
+# CONFIG_NSH_ARGCAT is not set
+CONFIG_NSH_NESTDEPTH=3
+# CONFIG_NSH_DISABLEBG is not set
+
+#
+# Disable Individual commands
+#
+CONFIG_NSH_DISABLE_ADDROUTE=y
+# CONFIG_NSH_DISABLE_CAT is not set
+CONFIG_NSH_DISABLE_CD=y
+CONFIG_NSH_DISABLE_CP=y
+# CONFIG_NSH_DISABLE_CMP is not set
+CONFIG_NSH_DISABLE_DATE=y
+CONFIG_NSH_DISABLE_DD=y
+CONFIG_NSH_DISABLE_DF=y
+CONFIG_NSH_DISABLE_DELROUTE=y
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_EXEC is not set
+# CONFIG_NSH_DISABLE_EXIT is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+CONFIG_NSH_DISABLE_GET=y
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_HEXDUMP is not set
+CONFIG_NSH_DISABLE_IFCONFIG=y
+# CONFIG_NSH_DISABLE_KILL is not set
+CONFIG_NSH_DISABLE_LOSETUP=y
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MB is not set
+CONFIG_NSH_DISABLE_MKDIR=y
+# CONFIG_NSH_DISABLE_MKFIFO is not set
+CONFIG_NSH_DISABLE_MKRD=y
+# CONFIG_NSH_DISABLE_MH is not set
+CONFIG_NSH_DISABLE_MOUNT=y
+CONFIG_NSH_DISABLE_MV=y
+# CONFIG_NSH_DISABLE_MW is not set
+# CONFIG_NSH_DISABLE_PS is not set
+CONFIG_NSH_DISABLE_PUT=y
+# CONFIG_NSH_DISABLE_PWD is not set
+CONFIG_NSH_DISABLE_RM=y
+CONFIG_NSH_DISABLE_RMDIR=y
+# CONFIG_NSH_DISABLE_SET is not set
+# CONFIG_NSH_DISABLE_SH is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+CONFIG_NSH_DISABLE_UMOUNT=y
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
+CONFIG_NSH_DISABLE_WGET=y
+# CONFIG_NSH_DISABLE_XD is not set
+
+#
+# Configure Command Options
+#
+CONFIG_NSH_CODECS_BUFSIZE=128
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_NSH_FILEIOSIZE=64
+
+#
+# Scripting Support
+#
+CONFIG_NSH_DISABLESCRIPT=y
+
+#
+# Console Configuration
+#
+CONFIG_NSH_CONSOLE=y
+# CONFIG_NSH_ALTCONDEV is not set
+# CONFIG_NSH_ARCHINIT is not set
+
+#
+# NxWidgets/NxWM
+#
+
+#
+# Platform-specific Support
+#
+# CONFIG_PLATFORM_CONFIGDATA is not set
+
+#
+# System Libraries and NSH Add-Ons
+#
+# CONFIG_SYSTEM_FREE is not set
+# CONFIG_SYSTEM_CLE is not set
+# CONFIG_SYSTEM_CUTERM is not set
+# CONFIG_SYSTEM_INSTALL is not set
+# CONFIG_SYSTEM_HEX2BIN is not set
+# CONFIG_SYSTEM_INIFILE is not set
+# CONFIG_SYSTEM_RAMTEST is not set
+CONFIG_SYSTEM_READLINE=y
+CONFIG_READLINE_ECHO=y
+# CONFIG_SYSTEM_POWEROFF is not set
+# CONFIG_SYSTEM_RAMTRON is not set
+# CONFIG_SYSTEM_SDCARD is not set
+# CONFIG_SYSTEM_SUDOKU is not set
+# CONFIG_SYSTEM_SYSINFO is not set
+# CONFIG_SYSTEM_VI is not set
+# CONFIG_SYSTEM_ZMODEM is not set
diff --git a/configs/lpcxpresso-lpc1115/minnsh/setenv.sh b/configs/lpcxpresso-lpc1115/minnsh/setenv.sh
new file mode 100644
index 0000000000..9eeeb48982
--- /dev/null
+++ b/configs/lpcxpresso-lpc1115/minnsh/setenv.sh
@@ -0,0 +1,72 @@
+#!/bin/bash
+# configs/lpcxpresso-lpc1115/minnsh/setenv.sh
+#
+#   Copyright (C) 2015 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$(basename $0)" = "setenv.sh" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
+
+WD=`pwd`
+
+# This is the Cygwin path to the location where I installed the CodeSourcery
+# toolchain under windows.  You will also have to edit this if you install
+# the CodeSourcery toolchain in any other location
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery_CodeBench_Lite_for_ARM_EABI/bin"
+# export TOOLCHAIN_BIN="/cygdrive/c/Users/MyName/MentorGraphics/Sourcery_CodeBench_Lite_for_ARM_EABI/bin"
+
+# This is the location where I installed the ARM "GNU Tools for ARM Embedded Processors"
+# You can this free toolchain here https://launchpad.net/gcc-arm-embedded
+export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/GNU Tools ARM Embedded/4.9 2014q4/bin"
+
+# This is the path to the location where I installed the devkitARM toolchain
+# You can get this free toolchain from http://devkitpro.org/ or http://sourceforge.net/projects/devkitpro/
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/devkitARM/bin"
+
+# This is the default install location for Code Red on Linux
+# export TOOLCHAIN_BIN="/usr/local/LPCXpresso/tools/bin"
+
+# This is the Cygwin path to the LPCXpresso 3.6 install location under Windows
+#export TOOLCHAIN_BIN="/cygdrive/c/nxp/lpcxpresso_3.6/Tools/bin"
+
+# This is the Cygwin path to the location where I build the buildroot
+# toolchain.
+# export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
+
+# Add the path to the toolchain to the PATH varialble
+export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"