Misc changes from Richard Cochran

ChangeLog

@@ -6463,5 +6463,6 @@
 	  is not really important because up_disable_irq() is not really used
 	  for that purpose.  But some spurions STM32 ADC interrupts have been
 	  reported to me and this turned out to be the cause in that case.  My
-	  concern not that up_disable_irq() works is that there may now be
-	  unmasked bugs that leave devices in the disabled state? (2014-1-15).
+	  concern now that up_disable_irq() works is that there may now be
+	  unmasked bugs that leave devices in the disabled state?  Thanks to
+	  Manuel Stühn for the tip(2014-1-15).

arch/README.txt

@@ -234,7 +234,7 @@ arch/avr
     MCU families.  STATUS:  Under development.
 
     arch/avr/include/avr and arch/avr/src/avr
-      Common support for all 8-bit VR MCUs
+      Common support for all 8-bit AVR MCUs
 
     arch/avr/include/atmega and arch/avr/src/atmega
       Support specifically for the AVR ATMega family (specifically only for

arch/avr/include/atmega/irq.h

@@ -1,5 +1,5 @@
 /****************************************************************************
- * arch/avr/include/avr/atmega/irq.h
+ * arch/avr/include/atmega/irq.h
  *
  *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
  *   Author: Gregory Nutt <gnutt@nuttx.org>

arch/avr/src/atmega/atmega_head.S

@@ -1,5 +1,5 @@
 /****************************************************************************
- * arch/avr32/src/atmega/atmega_head.S
+ * arch/avr/src/atmega/atmega_head.S
  *
  *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
  *   Author: Gregory Nutt <gnutt@nuttx.org>

configs/amber/src/up_boot.c

@@ -1,6 +1,5 @@
 /************************************************************************************
  * configs/amber/src/up_boot.c
- * arch/mips/src/board/up_boot.c
  *
  *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
  *   Author: Gregory Nutt <gnutt@nuttx.org>

configs/lm3s6965-ek/discover/defconfig

@@ -343,7 +343,7 @@ CONFIG_NET_TCP_RECVDELAY=0
 CONFIG_NET_UDP=y
 CONFIG_NET_UDP_CHECKSUMS=y
 CONFIG_NET_UDP_CONNS=8
-# CONFIG_NET_BROADCAST is not set
+CONFIG_NET_BROADCAST=y
 CONFIG_NET_ICMP=y
 CONFIG_NET_ICMP_PING=y
 # CONFIG_NET_PINGADDRCONF is not set

configs/lm3s6965-ek/nsh/defconfig

@@ -343,7 +343,7 @@ CONFIG_NET_TCP_RECVDELAY=0
 CONFIG_NET_UDP=y
 CONFIG_NET_UDP_CHECKSUMS=y
 CONFIG_NET_UDP_CONNS=8
-# CONFIG_NET_BROADCAST is not set
+CONFIG_NET_BROADCAST=y
 CONFIG_NET_ICMP=y
 CONFIG_NET_ICMP_PING=y
 # CONFIG_NET_PINGADDRCONF is not set

configs/lm3s6965-ek/tcpecho/defconfig

@@ -375,7 +375,7 @@ CONFIG_NET_TCPBACKLOG=y
 CONFIG_NET_UDP=y
 CONFIG_NET_UDP_CHECKSUMS=y
 CONFIG_NET_UDP_CONNS=8
-# CONFIG_NET_BROADCAST is not set
+CONFIG_NET_BROADCAST=y
 CONFIG_NET_ICMP=y
 CONFIG_NET_ICMP_PING=y
 # CONFIG_NET_PINGADDRCONF is not set

tools/configure.sh

@@ -193,14 +193,14 @@ fi
 
 # Okay... Everything looks good.  Setup the configuration
 
-install "${src_makedefs}" "${dest_makedefs}" || \
+install --mode=644 "${src_makedefs}" "${dest_makedefs}" || \
   { echo "Failed to copy \"${src_makedefs}\"" ; exit 7 ; }
 if [ "X${have_setenv}" = "Xy" ]; then
   install "${src_setenv}" "${dest_setenv}" || \
     { echo "Failed to copy ${src_setenv}" ; exit 8 ; }
   chmod 755 "${dest_setenv}"
 fi
-install "${src_config}" "${dest_config}" || \
+install --mode=644 "${src_config}" "${dest_config}" || \
   { echo "Failed to copy \"${src_config}\"" ; exit 9 ; }
 
 # If we did not use the CONFIG_APPS_DIR that was in the defconfig config file,
@@ -227,7 +227,7 @@ if [ ! -z "${appdir}" -a "X${newconfig}" != "Xy" ]; then
   if [ ! -r "${configpath}/appconfig" ]; then
     echo "NOTE: No readable appconfig file found in ${configpath}"
   else
-    install "${configpath}/appconfig" "${TOPDIR}/${posappdir}/.config" || \
+    install --mode=644 "${configpath}/appconfig" "${TOPDIR}/${posappdir}/.config" || \
       { echo "Failed to copy ${configpath}/appconfig" ; exit 10 ; }
   fi
 fi