diff --git a/drivers/sensors/Kconfig b/drivers/sensors/Kconfig index 90218fe0ee..94a43a53c2 100644 --- a/drivers/sensors/Kconfig +++ b/drivers/sensors/Kconfig @@ -173,6 +173,13 @@ config I2C_LM75 bool default y if LM75 +config LIS3MDL + bool "STMicro LIS3MDL 3-Axis magnetometer support" + default n + select SPI + ---help--- + Enable driver support for the ST LIS3MDL 3-axis magnetometer. + config LM75 bool "STMicro LM-75 Temperature Sensor support" default n diff --git a/drivers/sensors/Make.defs b/drivers/sensors/Make.defs index 21219588b3..4af5755c2c 100644 --- a/drivers/sensors/Make.defs +++ b/drivers/sensors/Make.defs @@ -113,6 +113,11 @@ endif ifeq ($(CONFIG_MPL115A),y) CSRCS += mpl115a.c endif + +ifeq ($(CONFIG_LIS3MDL),y) + CSRCS += lis3mdl.c +endif + endif # CONFIG_SPI # Quadrature encoder upper half diff --git a/drivers/sensors/lis3mdl.c b/drivers/sensors/lis3mdl.c new file mode 100644 index 0000000000..eeccf352f3 --- /dev/null +++ b/drivers/sensors/lis3mdl.c @@ -0,0 +1,630 @@ +/**************************************************************************** + * drivers/sensors/lis3mdl.c + * Character driver for the LIS3MDL 3-Axis magnetometer. + * + * Copyright (C) 2016 DS-Automotion GmbH. All rights reserved. + * Author: Alexander Entinger + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include + +#include +#include +#include +#include + +#include +#include + +#include +#include + +#if defined(CONFIG_SPI) && defined(CONFIG_LIS3MDL) + +/**************************************************************************** + * Private + ****************************************************************************/ + +struct lis3mdl_sensor_data_s +{ + int16_t x_mag; /* Measurement result for x axis */ + int16_t y_mag; /* Measurement result for y axis */ + int16_t z_mag; /* Measurement result for z axis */ + int16_t temperature; /* Measurement result for temperature sensor */ +}; + +struct lis3mdl_dev_s +{ + FAR struct lis3mdl_dev_s *flink; /* Supports a singly linked list of + * drivers */ + FAR struct spi_dev_s *spi; /* Pointer to the SPI instance */ + FAR struct lis3mdl_config_s *config; /* Pointer to the configuration + * of the LIS3MDL sensor */ + sem_t datasem; /* Manages exclusive access to this + * structure */ + struct lis3mdl_sensor_data_s data; /* The data as measured by the sensor */ + struct work_s work; /* The work queue is responsible for + * retrieving the data from the + * sensor after the arrival of new + * data was signalled in an interrupt */ +}; + +/**************************************************************************** + * Private Function Prototypes + ****************************************************************************/ + +static void lis3mdl_read_register(FAR struct lis3mdl_dev_s *dev, + uint8_t const reg_addr, uint8_t * reg_data); +static void lis3mdl_write_register(FAR struct lis3mdl_dev_s *dev, + uint8_t const reg_addr, + uint8_t const reg_data); +static void lis3mdl_reset(FAR struct lis3mdl_dev_s *dev); +static void lis3mdl_read_measurement_data(FAR struct lis3mdl_dev_s *dev); +static void lis3mdl_read_magnetic_data(FAR struct lis3mdl_dev_s *dev, + uint16_t * x_mag, uint16_t * y_mag, + uint16_t * z_mag); +static void lis3mdl_read_temperature(FAR struct lis3mdl_dev_s *dev, + uint16_t * temperature); +static int lis3mdl_interrupt_handler(int irq, FAR void *context); +static void lis3mdl_worker(FAR void *arg); + +static int lis3mdl_open(FAR struct file *filep); +static int lis3mdl_close(FAR struct file *filep); +static ssize_t lis3mdl_read(FAR struct file *, FAR char *, size_t); +static ssize_t lis3mdl_write(FAR struct file *filep, FAR const char *buffer, + size_t buflen); +static int lis3mdl_ioctl(FAR struct file *filep, int cmd, unsigned long arg); + +/**************************************************************************** + * Private Data + ****************************************************************************/ + +static const struct file_operations g_lis3mdl_fops = +{ + lis3mdl_open, + lis3mdl_close, + lis3mdl_read, + lis3mdl_write, + NULL, + lis3mdl_ioctl +#ifndef CONFIG_DISABLE_POLL + , NULL +#endif +#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS + , NULL +#endif +}; + +/* Single linked list to store instances of drivers */ + +static struct lis3mdl_dev_s *g_lis3mdl_list = 0; + +/**************************************************************************** + * Private Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: lis3mdl_read_register + ****************************************************************************/ + +static void lis3mdl_read_register(FAR struct lis3mdl_dev_s *dev, + uint8_t const reg_addr, uint8_t * reg_data) +{ + /* Lock the SPI bus so that only one device can access it at the same time */ + + SPI_LOCK(dev->spi, true); + + /* Set CS to low which selects the LIS3MDL */ + + SPI_SELECT(dev->spi, dev->config->spi_devid, true); + + /* Transmit the register address from where we want to read - the MSB needs + * to be set to indicate the read indication. + */ + + SPI_SEND(dev->spi, reg_addr | 0x80); + + /* Write an idle byte while receiving the required data */ + + *reg_data = (uint8_t) (SPI_SEND(dev->spi, 0)); + + /* Set CS to high which deselects the LIS3MDL */ + + SPI_SELECT(dev->spi, dev->config->spi_devid, false); + + /* Unlock the SPI bus */ + + SPI_LOCK(dev->spi, false); +} + +/**************************************************************************** + * Name: lis3mdl_write_register + ****************************************************************************/ + +static void lis3mdl_write_register(FAR struct lis3mdl_dev_s *dev, + uint8_t const reg_addr, + uint8_t const reg_data) +{ + /* Lock the SPI bus so that only one device can access it at the same time */ + + SPI_LOCK(dev->spi, true); + + /* Set CS to low which selects the LIS3MDL */ + + SPI_SELECT(dev->spi, dev->config->spi_devid, true); + + /* Transmit the register address from where we want to read */ + + SPI_SEND(dev->spi, reg_addr); + + /* Transmit the content which should be written in the register */ + + SPI_SEND(dev->spi, reg_data); + + /* Set CS to high which deselects the LIS3MDL */ + + SPI_SELECT(dev->spi, dev->config->spi_devid, false); + + /* Unlock the SPI bus */ + + SPI_LOCK(dev->spi, false); +} + +/**************************************************************************** + * Name: lis3mdl_reset + ****************************************************************************/ + +static void lis3mdl_reset(FAR struct lis3mdl_dev_s *dev) +{ + lis3mdl_write_register(dev, + LIS3MDL_CTRL_REG_2, LIS3MDL_CTRL_REG_2_SOFT_RST_bm); + + up_mdelay(100); +} + +/**************************************************************************** + * Name: lis3mdl_interrupt_handler + ****************************************************************************/ + +static void lis3mdl_read_measurement_data(FAR struct lis3mdl_dev_s *dev) +{ + /* Magnetic data */ + + uint16_t x_mag = 0, y_mag = 0, z_mag = 0; + + lis3mdl_read_magnetic_data(dev, &x_mag, &y_mag, &z_mag); + + /* Temperature */ + + uint16_t temperature = 0; + + lis3mdl_read_temperature(dev, &temperature); + + /* Aquire the semaphore before the data is copied */ + + int ret = sem_wait(&dev->datasem); + if (ret != OK) + { + snerr("Could not aquire dev->datasem: %d\n", ret); + return; + } + + /* Copy retrieve data to internal data structure */ + + dev->data.x_mag = (int16_t) (x_mag); + dev->data.y_mag = (int16_t) (y_mag); + dev->data.z_mag = (int16_t) (z_mag); + dev->data.temperature = (int16_t) (temperature); + + /* Give back the semaphore */ + + sem_post(&dev->datasem); +} + +/**************************************************************************** + * Name: lis3mdl_read_magnetic_data + ****************************************************************************/ + +static void lis3mdl_read_magnetic_data(FAR struct lis3mdl_dev_s *dev, + uint16_t * x_mag, uint16_t * y_mag, + uint16_t * z_mag) +{ + /* Lock the SPI bus so that only one device can access it at the same time */ + + SPI_LOCK(dev->spi, true); + + /* Set CS to low which selects the LIS3MDL */ + + SPI_SELECT(dev->spi, dev->config->spi_devid, true); + + /* Transmit the register address from where we want to start reading 0x80 -> + * MSB is set -> Read Indication 0x40 -> MSB-1 (MS-Bit) is set -> auto + * increment of address when reading multiple bytes. + */ + + SPI_SEND(dev->spi, (LIS3MDL_OUT_X_L_REG | 0x80 | 0x40)); /* RX */ + *x_mag = ((uint16_t) (SPI_SEND(dev->spi, 0)) << 0); /* LSB */ + *x_mag |= ((uint16_t) (SPI_SEND(dev->spi, 0)) << 8); /* MSB */ + + *y_mag = ((uint16_t) (SPI_SEND(dev->spi, 0)) << 0); /* LSB */ + *y_mag |= ((uint16_t) (SPI_SEND(dev->spi, 0)) << 8); /* MSB */ + + *z_mag = ((uint16_t) (SPI_SEND(dev->spi, 0)) << 0); /* LSB */ + *z_mag |= ((uint16_t) (SPI_SEND(dev->spi, 0)) << 8); /* MSB */ + + /* Set CS to high which deselects the LIS3MDL */ + + SPI_SELECT(dev->spi, dev->config->spi_devid, false); + + /* Unlock the SPI bus */ + + SPI_LOCK(dev->spi, false); +} + +/**************************************************************************** + * Name: lis3mdl_read_temperature + ****************************************************************************/ + +static void lis3mdl_read_temperature(FAR struct lis3mdl_dev_s *dev, + uint16_t * temperature) +{ + /* Lock the SPI bus so that only one device can access it at the same time */ + + SPI_LOCK(dev->spi, true); + + /* Set CS to low which selects the LIS3MDL */ + + SPI_SELECT(dev->spi, dev->config->spi_devid, true); + + /* Transmit the register address from where we want to start reading 0x80 -> + * MSB is set -> Read Indication 0x40 -> MSB-1 (MS-Bit) is set -> auto + * increment of address when reading multiple bytes */ + + SPI_SEND(dev->spi, (LIS3MDL_TEMP_OUT_L_REG | 0x80 | 0x40)); + + /* RX */ + + *temperature = ((uint16_t) (SPI_SEND(dev->spi, 0)) << 0); /* LSB */ + *temperature |= ((uint16_t) (SPI_SEND(dev->spi, 0)) << 8); /* MSB */ + + /* Set CS to high which deselects the LIS3MDL */ + + SPI_SELECT(dev->spi, dev->config->spi_devid, false); + + /* Unlock the SPI bus */ + + SPI_LOCK(dev->spi, false); +} + +/**************************************************************************** + * Name: lis3mdl_interrupt_handler + ****************************************************************************/ + +static int lis3mdl_interrupt_handler(int irq, FAR void *context) +{ + /* This function should be called upon a rising edge on the LIS3MDL DRDY pin + * since it signals that new data has been measured. */ + + FAR struct lis3mdl_dev_s *priv = 0; + int ret; + + /* Find out which LIS3MDL device caused the interrupt */ + + for (priv = g_lis3mdl_list; priv && priv->config->irq != irq; + priv = priv->flink); + DEBUGASSERT(priv != NULL); + + /* Task the worker with retrieving the latest sensor data. We should not do + * this in a interrupt since it might take too long. Also we cannot lock the + * SPI bus from within an interrupt. */ + + DEBUGASSERT(priv->work.worker == NULL); + ret = work_queue(HPWORK, &priv->work, lis3mdl_worker, priv, 0); + if (ret != 0) + { + snerr("Failed to queue work: %d\n", ret); + return ERROR; + } + else + { + return OK; + } +} + +/**************************************************************************** + * Name: lis3mdl_worker + ****************************************************************************/ + +static void lis3mdl_worker(FAR void *arg) +{ + FAR struct lis3mdl_dev_s *priv = (FAR struct lis3mdl_dev_s *)(arg); + DEBUGASSERT(priv != NULL); + + /* Read out the latest sensor data */ + + lis3mdl_read_measurement_data(priv); +} + +/**************************************************************************** + * Name: lis3mdl_open + ****************************************************************************/ +static int lis3mdl_open(FAR struct file *filep) +{ + FAR struct inode *inode = filep->f_inode; + FAR struct lis3mdl_dev_s *priv = inode->i_private; + uint8_t reg_content; + uint8_t reg_addr; + + DEBUGASSERT(priv != NULL); + + /* Perform a reset */ + + lis3mdl_reset(priv); + + /* Enable * - the maximum full scale mode. * Full scale = +/- 1.6 mT (16 + * Gauss) */ + + lis3mdl_write_register(priv, + LIS3MDL_CTRL_REG_2, + LIS3MDL_CTRL_REG_2_FS_1_bm | + LIS3MDL_CTRL_REG_2_FS_0_bm); + + /* Enable - temperature sensor - ultra high performance mode (UMP) for X and + * Y - fast output data rates This results in a output data rate of 155 Hz + * for X and Y */ + + lis3mdl_write_register(priv, + LIS3MDL_CTRL_REG_1, + LIS3MDL_CTRL_REG_1_TEMP_EN_bm | + LIS3MDL_CTRL_REG_1_OM_1_bm | LIS3MDL_CTRL_REG_1_OM_0_bm + | LIS3MDL_CTRL_REG_1_FAST_ODR_bm); + + /* Enable * - ultra high performance mode (UMP) for Z * This should result to + * the same output data rate as for X and Y. */ + + lis3mdl_write_register(priv, + LIS3MDL_CTRL_REG_4, + LIS3MDL_CTRL_REG_4_OMZ_1_bm | + LIS3MDL_CTRL_REG_4_OMZ_0_bm); + + /* Enable * - block data update for magnetic sensor data * This should + * prevent race conditions when reading sensor data. */ + + lis3mdl_write_register(priv, LIS3MDL_CTRL_REG_5, LIS3MDL_CTRL_REG_5_BDU_bm); + + /* Enable continous conversion mode - the device starts measuring now. */ + + lis3mdl_write_register(priv, LIS3MDL_CTRL_REG_3, 0); + + /* Read measurement data to ensure DRDY is low */ + + lis3mdl_read_measurement_data(priv); + + /* Read back the content of all control registers for debug purposes */ + + reg_content = 0; + eg_addr = LIS3MDL_CTRL_REG_1; + for (; reg_addr <= LIS3MDL_CTRL_REG_5; reg_addr++) + { + lis3mdl_read_register(priv, reg_addr, ®_content); + snerr("R#%04x = %04x\n", reg_addr, reg_content); + } + + lis3mdl_read_register(priv, LIS3MDL_STATUS_REG, ®_content); + snerr("STATUS_REG = %04x\n", reg_content); + + return OK; +} + +/**************************************************************************** + * Name: lis3mdl_close + ****************************************************************************/ + +static int lis3mdl_close(FAR struct file *filep) +{ + FAR struct inode *inode = filep->f_inode; + FAR struct lis3mdl_dev_s *priv = inode->i_private; + + DEBUGASSERT(priv != NULL); + + /* Perform a reset */ + + lis3mdl_reset(priv); + + return OK; +} + +/**************************************************************************** + * Name: lis3mdl_read + ****************************************************************************/ +static ssize_t lis3mdl_read(FAR struct file *filep, FAR char *buffer, + size_t buflen) +{ + FAR struct inode *inode = filep->f_inode; + FAR struct lis3mdl_dev_s *priv = inode->i_private; + FAR struct lis3mdl_sensor_data_s *data; + int ret; + + DEBUGASSERT(priv != NULL); + + /* Check if enough memory was provided for the read call */ + + if (buflen < sizeof(FAR struct lis3mdl_sensor_data_s)) + { + snerr("Not enough memory for reading out a sensor data sample\n"); + return -ENOSYS; + } + + /* Aquire the semaphore before the data is copied */ + + ret = sem_wait(&priv->datasem); + if (ret != OK) + { + snerr("Could not aquire priv->datasem: %d\n", ret); + return ERROR; + } + + /* Copy the sensor data into the buffer */ + + data = (FAR struct lis3mdl_sensor_data_s *)buffer; + memset(data, 0, sizeof(FAR struct lis3mdl_sensor_data_s)); + + data->x_mag = priv->data.x_mag; + data->y_mag = priv->data.y_mag; + data->z_mag = priv->data.z_mag; + data->temperature = priv->data.temperature; + + /* Give back the semaphore */ + + sem_post(&priv->datasem); + + return sizeof(FAR struct lis3mdl_sensor_data_s); +} + +/**************************************************************************** + * Name: lis3mdl_write + ****************************************************************************/ + +static ssize_t lis3mdl_write(FAR struct file *filep, FAR const char *buffer, + size_t buflen) +{ + return -ENOSYS; +} + +/**************************************************************************** + * Name: lis3mdl_ioctl + ****************************************************************************/ + +static int lis3mdl_ioctl(FAR struct file *filep, int cmd, unsigned long arg) +{ + int ret = OK; + + switch (cmd) + { + /* Command was not recognized */ + + default: + snerr("Unrecognized cmd: %d\n", cmd); + ret = -ENOTTY; + break; + } + + return ret; +} + +/**************************************************************************** + * Public Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: lis3mdl_register + * + * Description: + * Register the LIS3MDL character device as 'devpath' + * + * Input Parameters: + * devpath - The full path to the driver to register. E.g., "/dev/mag0" + * spi - An instance of the SPI interface to use to communicate with LIS3MDL + * config - configuration for the LIS3MDL driver. For details see description above. + * + * Returned Value: + * Zero (OK) on success; a negated errno value on failure. + * + ****************************************************************************/ + +int lis3mdl_register(FAR const char *devpath, FAR struct spi_dev_s *spi, + FAR struct lis3mdl_config_s const *config) +{ + FAR struct lis3mdl_dev_s *priv; + int ret; + + /* Sanity check */ + + DEBUGASSERT(spi != NULL); + DEBUGASSERT(config != NULL); + + /* Initialize the LIS3MDL device structure */ + + priv = (FAR struct lis3mdl_dev_s *)kmm_malloc(sizeof(struct lis3mdl_dev_s)); + if (priv == NULL) + { + snerr("Failed to allocate instance\n"); + return -ENOMEM; + } + + priv->spi = spi; + priv->config = config; + + priv->work.worker = NULL; + + sem_init(&priv->datasem, 0, 1); /* Initialize sensor data access + * semaphore */ + + /* Setup SPI frequency and mode */ + + SPI_SETFREQUENCY(spi, LIS3MDL_SPI_FREQUENCY); + SPI_SETMODE(spi, LIS3MDL_SPI_MODE); + + /* Attach the interrupt handler */ + + ret = priv->config->attach(priv->config, &lis3mdl_interrupt_handler); + if (ret < 0) + { + snerr("Failed to attach interrupt\n"); + return -ENODEV; + } + + /* Register the character driver */ + + ret = register_driver(devpath, &g_lis3mdl_fops, 0666, priv); + if (ret < 0) + { + snerr("Failed to register driver: %d\n", ret); + kmm_free(priv); + sem_destroy(&priv->datasem); + return -ENODEV; + } + + /* Since we support multiple LIS3MDL devices are supported, we will need to + * add this new instance to a list of device instances so that it can be + * found by the interrupt handler based on the received IRQ number. */ + + priv->flink = g_lis3mdl_list; + g_lis3mdl_list = priv; + + return OK; +} + +#endif /* CONFIG_SPI && CONFIG_LIS3MDL */ diff --git a/include/nuttx/sensors/lis3mdl.h b/include/nuttx/sensors/lis3mdl.h new file mode 100644 index 0000000000..c702905807 --- /dev/null +++ b/include/nuttx/sensors/lis3mdl.h @@ -0,0 +1,178 @@ +/**************************************************************************** + * include/nuttx/sensors/lis3mdl.h + * + * Copyright (C) 2016 DS-Automotion GmbH. All rights reserved. + * Author: Alexander Entinger + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#ifndef NUTTX_INCLUDE_NUTTX_SENSORS_LIS3MDL_H_ +#define NUTTX_INCLUDE_NUTTX_SENSORS_LIS3MDL_H_ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include +#include +#include +#include + +#if defined(CONFIG_SPI) && defined(CONFIG_LIS3MDL) + +/**************************************************************************** + * Pre-processor Definitions + ****************************************************************************/ + +/* LIS3MDL Register Definitions *********************************************/ + +#define LIS3MDL_WHO_AM_I_REG (0x0F) +#define LIS3MDL_CTRL_REG_1 (0x20) +#define LIS3MDL_CTRL_REG_2 (0x21) +#define LIS3MDL_CTRL_REG_3 (0x22) +#define LIS3MDL_CTRL_REG_4 (0x23) +#define LIS3MDL_CTRL_REG_5 (0x24) +#define LIS3MDL_STATUS_REG (0x27) +#define LIS3MDL_OUT_X_L_REG (0x28) +#define LIS3MDL_OUT_X_H_REG (0x29) +#define LIS3MDL_OUT_Y_L_REG (0x2A) +#define LIS3MDL_OUT_Y_H_REG (0x2B) +#define LIS3MDL_OUT_Z_L_REG (0x2C) +#define LIS3MDL_OUT_Z_H_REG (0x2D) +#define LIS3MDL_TEMP_OUT_L_REG (0x2E) +#define LIS3MDL_TEMP_OUT_H_REG (0x2F) +#define LIS3MDL_INT_CFG_REG (0x30) +#define LIS3MDL_INT_SRC_REG (0x31) +#define LIS3MDL_INT_THS_L_REG (0x32) +#define LIS3MDL_INT_THS_H_REG (0x33) + +/* LIS3MDL CTRL_REG_1 Bit Definitions ***************************************/ + +#define LIS3MDL_CTRL_REG_1_TEMP_EN_bm (1<<7) /* Enable the temperature sensor */ +#define LIS3MDL_CTRL_REG_1_OM_1_bm (1<<6) /* Select the operating mode of X and Y axis bit 1 */ +#define LIS3MDL_CTRL_REG_1_OM_0_bm (1<<5) /* Select the operating mode of X and Y axis bit 0 */ +#define LIS3MDL_CTRL_REG_1_DO2_bm (1<<4) /* Output data rate selection bit 2 */ +#define LIS3MDL_CTRL_REG_1_DO1_bm (1<<3) /* Output data rate selection bit 1 */ +#define LIS3MDL_CTRL_REG_1_DO0_bm (1<<2) /* Output data rate selection bit 2 */ +#define LIS3MDL_CTRL_REG_1_FAST_ODR_bm (1<<1) /* Enable higher output data rates */ + +/* LIS3MDL CTRL_REG_2 Bit Definitions ***************************************/ + +#define LIS3MDL_CTRL_REG_2_FS_1_bm (1<<6) /* Full scale selection bit 1 */ +#define LIS3MDL_CTRL_REG_2_FS_0_bm (1<<5) /* Full scale selection bit 0 */ +#define LIS3MDL_CTRL_REG_2_REBOOT_bm (1<<3) /* Reboot Memory Content */ +#define LIS3MDL_CTRL_REG_2_SOFT_RST_bm (1<<2) /* Soft Reset */ + +/* LIS3MDL CTRL_REG_4 Bit Definitions ***************************************/ + +#define LIS3MDL_CTRL_REG_4_OMZ_1_bm (1<<3) /* Select the operating mode of Z axis bit 1 */ +#define LIS3MDL_CTRL_REG_4_OMZ_0_bm (1<<2) /* Select the operating mode of Z axis bit 0 */ + +/* LIS3MDL CTRL_REG_5 Bit Definitions ***************************************/ + +#define LIS3MDL_CTRL_REG_5_BDU_bm (1<<6) /* Enable block data update for magnetic data (prevent race conditions while reading) */ + +/* SPI BUS PARAMETERS *******************************************************/ + +#define LIS3MDL_SPI_FREQUENCY (1000000) /* 1 MHz */ +#define LIS3MDL_SPI_MODE (SPIDEV_MODE3) /* Device uses SPI Mode 3: CPOL=1, CPHA=1 */ + +/**************************************************************************** + * Public Types + ****************************************************************************/ + +/* A reference to a structure of this type must be passed to the LIS3MDL + * driver. This structure provides information about the configuration + * of the sensor and provides some board-specific hooks. + * + * Memory for this structure is provided by the caller. It is not copied + * by the driver and is presumed to persist while the driver is active. + */ + +struct lis3mdl_config_s +{ + /* Since multiple LIS3MDL can be connected to the same SPI bus we need + * to use multiple spi device ids which are employed by NuttX to select/ + * deselect the desired LIS3MDL chip via their chip select inputs. + */ + + int spi_devid; + + /* The IRQ number must be provided for each so LIS3MDL device so that + * their interrupts can be distinguished. + */ + + int irq; + + /* Attach the LIS3MDL interrupt handler to the GPIO interrupt of the + * concrete LIS3MDL instance. + */ + + int (*attach)(FAR struct lis3mdl_config_s *, xcpt_t); +}; + +/**************************************************************************** + * Public Function Prototypes + ****************************************************************************/ + +#ifdef __cplusplus +#define EXTERN extern "C" +extern "C" +{ +#else +#define EXTERN extern +#endif + +/**************************************************************************** + * Name: lis3mdl_register + * + * Description: + * Register the LIS3MDL character device as 'devpath' + * + * Input Parameters: + * devpath - The full path to the driver to register. E.g., "/dev/mag0" + * spi - An instance of the SPI interface to use to communicate with LIS3MDL + * config - configuration for the LIS3MDL driver. For details see description above. + * + * Returned Value: + * Zero (OK) on success; a negated errno value on failure. + * + ****************************************************************************/ + +int lis3mdl_register(FAR const char *devpath, FAR struct spi_dev_s *spi, + FAR struct lis3mdl_config_s const *config); + +#undef EXTERN +#ifdef __cplusplus +} +#endif + +#endif /* CONFIG_SPI && CONFIG_LIS3MDL */ +#endif /* NUTTX_INCLUDE_NUTTX_SENSORS_LIS3MDL_H_ */