Viewtool STM32F107: Add a NSH configuration with network support
This commit is contained in:
Gregory Nutt
parent
d3462d4f0b
commit
4a25bc236b
@ -25,6 +25,7 @@ Contents
|
||||
- J5 - USART1
|
||||
- PL-2013 USB-to-Serial Interface
|
||||
- RS-232 Module
|
||||
o ViewTool DP83848 Ethernet Module
|
||||
o Toolchains
|
||||
- NOTE about Windows native toolchains
|
||||
o Configurations
|
||||
@ -118,6 +119,93 @@ Serial Console
|
||||
J35 - CON2. Jumper Setting:
|
||||
1 <-> 2 : Proves 3.3V to the RS-232 module.
|
||||
|
||||
ViewTool DP83848 Ethernet Module
|
||||
================================
|
||||
|
||||
Ethernet Connector
|
||||
------------------
|
||||
|
||||
----------------------------- ------------------------ --------------------------------
|
||||
Connector J2 GPIO CONFIGURATION(s)
|
||||
PIN SIGNAL LEGEND (no remapping) DP83848C Board
|
||||
--- ------------- ----------- ------------------------ --------------------------------
|
||||
1 PA0 MII_CRS N/A N/C
|
||||
2 PB11/SDA2 COM_TX_EN GPIO_ETH_RMII_TX_EN TX_EN
|
||||
3 PA3/LED_G2 MII_COL N/A N/C
|
||||
4 PB12/NSS2 COM_TXD0 GPIO_ETH_RMII_TXD0 TXD0
|
||||
5 PA1 MII_RX_CLK GPIO_ETH_RMII_REF_CLK OSCIN
|
||||
6 PB13/SCK2 COM_TXD1 GPIO_ETH_RMII_TXD1 TXD1
|
||||
7 PB1/CD_RESET MII_RXD3 N/A N/C
|
||||
8 PC4/LCDTP COM_RXD0 GPIO_ETH_RMII_RXD0 RXD0
|
||||
9 PB0/BL_PWM MII_RXD2 N/A N/C
|
||||
10 PC5 COM_RXD1 GPIO_ETH_RMII_RXD1 RXD1
|
||||
11 PB8/CAN1_RX MII_TXD3 N/A N/C
|
||||
12 PC1/LED_R1 COM_MDC GPIO_ETH_MDC MDC
|
||||
13 PC2/LED_R2 MII_TXD2 N/A N/C
|
||||
14 PA2/LED_G1 COM_MDIO GPIO_ETH_MDIO MDIO
|
||||
15 PC3/ONEW MII_TX_CLK N/A N/C
|
||||
16 PB10/SCL2 RX_ER N/A N/C
|
||||
17 PD2 GPIO1 N/A N/C
|
||||
18 PA7/MOSI1 COM_RX_DV GPIO_ETH_RMII_CRS_DV CRS_DIV
|
||||
19 PD3 GPIO2 N/A N/C
|
||||
20 PB5 COM_PPS_OUT N/A N/C
|
||||
21 VDD 3.3 VDD_3.3 N/A 3.3V
|
||||
22 VDD 3.3 VDD_3.3 N/A 3.3V
|
||||
23 GND GND N/A GND
|
||||
24 GND GND N/A GND
|
||||
--- ------------- ----------- ------------------------ --------------------------------
|
||||
|
||||
NOTES:
|
||||
1. RMII interface is used
|
||||
2. There is a 50MHz clock on board the DP83848. No MCO clock need be provided.
|
||||
|
||||
Configuration
|
||||
-------------
|
||||
|
||||
System Type -> STM32 Peripheral Support
|
||||
CONFIG_STM32_ETHMAC=y
|
||||
|
||||
System Type -> Ethernet MAC Configuration
|
||||
CONFIG_STM32_RMII=y
|
||||
CONFIG_STM32_AUTONEG=y
|
||||
CONFIG_STM32_PHYADDR=1
|
||||
CONFIG_STM32_PHYSR=16
|
||||
CONFIG_STM32_PHYSR_SPEED=0x0002
|
||||
CONFIG_STM32_PHYSR_100MBPS=0x0000
|
||||
CONFIG_STM32_PHYSR_MODE=0x0004
|
||||
CONFIG_STM32_PHYSR_FULLDUPLEX=0x0004
|
||||
CONFIG_STM32_RMII_EXTCLK=y
|
||||
|
||||
Device Drivers -> Networking Devices
|
||||
CONFIG_NETDEVICES=y
|
||||
CONFIG_ETH0_PHY_DP83848C=y
|
||||
|
||||
Networking (required)
|
||||
CONFIG_NET=y
|
||||
CONFIG_NET_MULTIBUFFER=y
|
||||
CONFIG_NSH_NOMAC=y
|
||||
|
||||
Networking (recommended/typical)
|
||||
CONFIG_NSOCKET_DESCRIPTORS=10
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
|
||||
CONFIG_NET_BUFSIZE=650
|
||||
CONFIG_NET_RECEIVE_WINDOW=650
|
||||
CONFIG_NET_TCP_READAHEAD_BUFSIZE=650
|
||||
|
||||
CONFIG_NET_TCP=y
|
||||
CONFIG_NET_NTCP_READAHEAD_BUFFERS=8
|
||||
|
||||
CONFIG_NET_UDP=y
|
||||
CONFIG_NET_UDP_CONNS=8
|
||||
|
||||
CONFIG_NET_ICMP=y
|
||||
CONFIG_NET_ICMP_PING=y
|
||||
|
||||
CONFIG_NSH_DRIPADDR=0x0a000001
|
||||
CONFIG_NSH_IPADDR=0x0a000002
|
||||
CONFIG_NSH_NETMASK=0xffffff00
|
||||
|
||||
Toolchains
|
||||
==========
|
||||
|
||||
@ -224,17 +312,64 @@ Configurations
|
||||
Configuration Sub-directories
|
||||
-----------------------------
|
||||
|
||||
nsh:
|
||||
netnsh:
|
||||
|
||||
This configuration directory provide the basuic NuttShell (NSH).
|
||||
This configuration directory provide the NuttShell (NSH) with
|
||||
networking support.
|
||||
|
||||
NOTES:
|
||||
1. This configuration uses the default USART1 serial console. That
|
||||
1. This configuration will work only on the version the viewtool
|
||||
board with the the STM32F107VCT6 installed. If you have a board
|
||||
with the STM32F103VCT6 installed, please use the nsh configuration
|
||||
described below.
|
||||
|
||||
2. There is no PHY on the base viewtool stm32f107 board. You must
|
||||
also have the "ViewTool DP83848 Ethernet Module" installed on J2
|
||||
in order to support networking.
|
||||
|
||||
3. Since networking is enabled, you will see some boot-up delays when
|
||||
the network connection is established. These delays can be quite
|
||||
large is no network is attached (A production design to bring up the
|
||||
network asynchronously to avoid these start up delays).
|
||||
|
||||
4. This configuration uses the default USART1 serial console. That
|
||||
is easily changed by reconfiguring to (1) enable a different
|
||||
serial peripheral, and (2) selecting that serial peripheral as
|
||||
the console device.
|
||||
|
||||
2. By default, this configuration is set up to build on Windows
|
||||
5. By default, this configuration is set up to build on Windows
|
||||
under either a Cygwin or MSYS environment using a recent, Windows-
|
||||
native, generic ARM EABI GCC toolchain (such as the CodeSourcery
|
||||
toolchain). Both the build environment and the toolchain
|
||||
selection can easily be changed by reconfiguring:
|
||||
|
||||
CONFIG_HOST_WINDOWS=y : Windows operating system
|
||||
CONFIG_WINDOWS_CYGWIN=y : POSIX environment under windows
|
||||
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery for Windows
|
||||
|
||||
STATUS: As of this writing (2013-12-25), the STM32 communicates with the
|
||||
PHY, but the DP83848 fails to return good linkstatus from the STM32.
|
||||
|
||||
nsh:
|
||||
|
||||
This configuration directory provide the basic NuttShell (NSH).
|
||||
|
||||
NOTES:
|
||||
1. This configuration will work with either the version of the board
|
||||
with STM32F107VCT6 or STM32F103VCT6 installed. The default
|
||||
configuration is for the STM32F107VCT6. To use this configuration
|
||||
with a STM32F103VCT6, it would have to be modified as follows:
|
||||
|
||||
System Type -> STM32 Configuration Options
|
||||
CONFIG_ARCH_CHIP_STM32F103VCT6=y
|
||||
CONFIG_ARCH_CHIP_STM32F107VC=n
|
||||
|
||||
2. This configuration uses the default USART1 serial console. That
|
||||
is easily changed by reconfiguring to (1) enable a different
|
||||
serial peripheral, and (2) selecting that serial peripheral as
|
||||
the console device.
|
||||
|
||||
3. By default, this configuration is set up to build on Windows
|
||||
under either a Cygwin or MSYS environment using a recent, Windows-
|
||||
native, generic ARM EABI GCC toolchain (such as the CodeSourcery
|
||||
toolchain). Both the build environment and the toolchain
|
||||
|
||||
117
configs/viewtool-stm32f107/netnsh/Make.defs
Normal file
117
configs/viewtool-stm32f107/netnsh/Make.defs
Normal file
@ -0,0 +1,117 @@
|
||||
############################################################################
|
||||
# configs/viewtool-stm32f107/netnsh/Make.defs
|
||||
#
|
||||
# Copyright (C) 2013 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
include ${TOPDIR}/tools/Config.mk
|
||||
include ${TOPDIR}/arch/arm/src/armv7-m/Toolchain.defs
|
||||
|
||||
ifeq ($(CONFIG_STM32_DFU),y)
|
||||
LDSCRIPT = dfu.ld
|
||||
else
|
||||
LDSCRIPT = flash.ld
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/copydir.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)}"
|
||||
MAXOPTIMIZATION = -O2
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(CROSSDEV)ar rcs
|
||||
NM = $(CROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
ARCHOPTIMIZATION = -g
|
||||
endif
|
||||
|
||||
ifneq ($(CONFIG_DEBUG_NOOPT),y)
|
||||
ARCHOPTIMIZATION += $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions -fno-rtti
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-gotoff.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-nuttx-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
||||
953
configs/viewtool-stm32f107/netnsh/defconfig
Normal file
953
configs/viewtool-stm32f107/netnsh/defconfig
Normal file
@ -0,0 +1,953 @@
|
||||
#
|
||||
# Automatically generated file; DO NOT EDIT.
|
||||
# Nuttx/ Configuration
|
||||
#
|
||||
CONFIG_NUTTX_NEWCONFIG=y
|
||||
|
||||
#
|
||||
# Build Setup
|
||||
#
|
||||
# CONFIG_EXPERIMENTAL is not set
|
||||
# CONFIG_HOST_LINUX is not set
|
||||
# CONFIG_HOST_OSX is not set
|
||||
CONFIG_HOST_WINDOWS=y
|
||||
# CONFIG_HOST_OTHER is not set
|
||||
# CONFIG_WINDOWS_NATIVE is not set
|
||||
CONFIG_WINDOWS_CYGWIN=y
|
||||
# CONFIG_WINDOWS_MSYS is not set
|
||||
# CONFIG_WINDOWS_OTHER is not set
|
||||
|
||||
#
|
||||
# Build Configuration
|
||||
#
|
||||
# CONFIG_APPS_DIR="../apps"
|
||||
# CONFIG_BUILD_2PASS is not set
|
||||
|
||||
#
|
||||
# Binary Output Formats
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY is not set
|
||||
CONFIG_INTELHEX_BINARY=y
|
||||
# CONFIG_MOTOROLA_SREC is not set
|
||||
# CONFIG_RAW_BINARY is not set
|
||||
|
||||
#
|
||||
# Customize Header Files
|
||||
#
|
||||
# CONFIG_ARCH_STDBOOL_H is not set
|
||||
# CONFIG_ARCH_MATH_H is not set
|
||||
# CONFIG_ARCH_FLOAT_H is not set
|
||||
# CONFIG_ARCH_STDARG_H is not set
|
||||
|
||||
#
|
||||
# Debug Options
|
||||
#
|
||||
# CONFIG_DEBUG is not set
|
||||
CONFIG_ARCH_HAVE_STACKCHECK=y
|
||||
CONFIG_ARCH_HAVE_HEAPCHECK=y
|
||||
# CONFIG_DEBUG_SYMBOLS is not set
|
||||
# CONFIG_DEBUG_NOOPT is not set
|
||||
|
||||
#
|
||||
# System Type
|
||||
#
|
||||
# CONFIG_ARCH_8051 is not set
|
||||
CONFIG_ARCH_ARM=y
|
||||
# CONFIG_ARCH_AVR is not set
|
||||
# CONFIG_ARCH_HC is not set
|
||||
# CONFIG_ARCH_MIPS is not set
|
||||
# CONFIG_ARCH_RGMP is not set
|
||||
# CONFIG_ARCH_SH is not set
|
||||
# CONFIG_ARCH_SIM is not set
|
||||
# CONFIG_ARCH_X86 is not set
|
||||
# CONFIG_ARCH_Z16 is not set
|
||||
# CONFIG_ARCH_Z80 is not set
|
||||
CONFIG_ARCH="arm"
|
||||
|
||||
#
|
||||
# ARM Options
|
||||
#
|
||||
# CONFIG_ARCH_CHIP_A1X is not set
|
||||
# CONFIG_ARCH_CHIP_C5471 is not set
|
||||
# CONFIG_ARCH_CHIP_CALYPSO is not set
|
||||
# CONFIG_ARCH_CHIP_DM320 is not set
|
||||
# CONFIG_ARCH_CHIP_IMX is not set
|
||||
# CONFIG_ARCH_CHIP_KINETIS is not set
|
||||
# CONFIG_ARCH_CHIP_KL is not set
|
||||
# CONFIG_ARCH_CHIP_LM is not set
|
||||
# CONFIG_ARCH_CHIP_LPC17XX is not set
|
||||
# CONFIG_ARCH_CHIP_LPC214X is not set
|
||||
# CONFIG_ARCH_CHIP_LPC2378 is not set
|
||||
# CONFIG_ARCH_CHIP_LPC31XX is not set
|
||||
# CONFIG_ARCH_CHIP_LPC43XX is not set
|
||||
# CONFIG_ARCH_CHIP_NUC1XX is not set
|
||||
# CONFIG_ARCH_CHIP_SAMA5 is not set
|
||||
# CONFIG_ARCH_CHIP_SAM34 is not set
|
||||
CONFIG_ARCH_CHIP_STM32=y
|
||||
# CONFIG_ARCH_CHIP_STR71X is not set
|
||||
# CONFIG_ARCH_ARM7TDMI is not set
|
||||
# CONFIG_ARCH_ARM926EJS is not set
|
||||
# CONFIG_ARCH_ARM920T is not set
|
||||
# CONFIG_ARCH_CORTEXM0 is not set
|
||||
CONFIG_ARCH_CORTEXM3=y
|
||||
# CONFIG_ARCH_CORTEXM4 is not set
|
||||
# CONFIG_ARCH_CORTEXA5 is not set
|
||||
# CONFIG_ARCH_CORTEXA8 is not set
|
||||
CONFIG_ARCH_FAMILY="armv7-m"
|
||||
CONFIG_ARCH_CHIP="stm32"
|
||||
# CONFIG_ARMV7M_USEBASEPRI is not set
|
||||
CONFIG_ARCH_HAVE_CMNVECTOR=y
|
||||
# CONFIG_ARMV7M_CMNVECTOR is not set
|
||||
# CONFIG_ARCH_HAVE_FPU is not set
|
||||
CONFIG_ARCH_HAVE_MPU=y
|
||||
# CONFIG_ARMV7M_MPU is not set
|
||||
|
||||
#
|
||||
# ARMV7M Configuration Options
|
||||
#
|
||||
# CONFIG_ARMV7M_TOOLCHAIN_ATOLLIC is not set
|
||||
# CONFIG_ARMV7M_TOOLCHAIN_BUILDROOT is not set
|
||||
# CONFIG_ARMV7M_TOOLCHAIN_CODEREDW is not set
|
||||
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y
|
||||
# CONFIG_ARMV7M_TOOLCHAIN_DEVKITARM is not set
|
||||
# CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIL is not set
|
||||
# CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIW is not set
|
||||
# CONFIG_ARMV7M_TOOLCHAIN_RAISONANCE is not set
|
||||
# CONFIG_SERIAL_TERMIOS is not set
|
||||
# CONFIG_NET_MULTICAST is not set
|
||||
|
||||
#
|
||||
# STM32 Configuration Options
|
||||
#
|
||||
# CONFIG_ARCH_CHIP_STM32L151C6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L151C8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L151CB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L151R6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L151R8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L151RB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L151V6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L151V8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L151VB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152C6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152C8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152CB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152R6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152R8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152RB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152V6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152V8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32L152VB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100C8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100CB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100R8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100RB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100RC is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100RD is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100RE is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100V8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100VB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100VC is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100VD is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F100VE is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103C4 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103C8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103T8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103TB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103CB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103R8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103RB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103V8 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103VB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103RET6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103VCT6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103VET6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F103ZET6 is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F105VBT7 is not set
|
||||
CONFIG_ARCH_CHIP_STM32F107VC=y
|
||||
# CONFIG_ARCH_CHIP_STM32F207IG is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F207ZE is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F302CB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F302CC is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F302RB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F302RC is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F302VB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F302VC is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F303CB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F303CC is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F303RB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F303RC is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F303VB is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F303VC is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F405RG is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F405VG is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F405ZG is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F407VE is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F407VG is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F407ZE is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F407ZG is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F407IE is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F407IG is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F427V is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F427Z is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F427I is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F429V is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F429Z is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F429I is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F429B is not set
|
||||
# CONFIG_ARCH_CHIP_STM32F429N is not set
|
||||
# CONFIG_STM32_STM32L15XX is not set
|
||||
# CONFIG_STM32_ENERGYLITE is not set
|
||||
CONFIG_STM32_STM32F10XX=y
|
||||
# CONFIG_STM32_VALUELINE is not set
|
||||
CONFIG_STM32_CONNECTIVITYLINE=y
|
||||
# CONFIG_STM32_PERFORMANCELINE is not set
|
||||
# CONFIG_STM32_HIGHDENSITY is not set
|
||||
# CONFIG_STM32_MEDIUMDENSITY is not set
|
||||
# CONFIG_STM32_LOWDENSITY is not set
|
||||
# CONFIG_STM32_STM32F20XX is not set
|
||||
# CONFIG_STM32_STM32F30XX is not set
|
||||
# CONFIG_STM32_STM32F40XX is not set
|
||||
# CONFIG_STM32_DFU is not set
|
||||
|
||||
#
|
||||
# STM32 Peripheral Support
|
||||
#
|
||||
# CONFIG_STM32_ADC1 is not set
|
||||
# CONFIG_STM32_ADC2 is not set
|
||||
# CONFIG_STM32_ADC3 is not set
|
||||
# CONFIG_STM32_BKP is not set
|
||||
# CONFIG_STM32_CAN1 is not set
|
||||
# CONFIG_STM32_CRC is not set
|
||||
# CONFIG_STM32_DMA1 is not set
|
||||
# CONFIG_STM32_DMA2 is not set
|
||||
# CONFIG_STM32_DAC1 is not set
|
||||
# CONFIG_STM32_DAC2 is not set
|
||||
CONFIG_STM32_ETHMAC=y
|
||||
# CONFIG_STM32_I2C1 is not set
|
||||
# CONFIG_STM32_I2C2 is not set
|
||||
CONFIG_STM32_PWR=y
|
||||
# CONFIG_STM32_SPI1 is not set
|
||||
# CONFIG_STM32_SPI2 is not set
|
||||
# CONFIG_STM32_SPI3 is not set
|
||||
# CONFIG_STM32_TIM1 is not set
|
||||
# CONFIG_STM32_TIM2 is not set
|
||||
# CONFIG_STM32_TIM3 is not set
|
||||
# CONFIG_STM32_TIM4 is not set
|
||||
# CONFIG_STM32_TIM5 is not set
|
||||
# CONFIG_STM32_TIM6 is not set
|
||||
# CONFIG_STM32_TIM7 is not set
|
||||
# CONFIG_STM32_TIM8 is not set
|
||||
CONFIG_STM32_USART1=y
|
||||
# CONFIG_STM32_USART2 is not set
|
||||
# CONFIG_STM32_USART3 is not set
|
||||
# CONFIG_STM32_UART4 is not set
|
||||
# CONFIG_STM32_UART5 is not set
|
||||
# CONFIG_STM32_USB is not set
|
||||
# CONFIG_STM32_IWDG is not set
|
||||
# CONFIG_STM32_WWDG is not set
|
||||
|
||||
#
|
||||
# Alternate Pin Mapping
|
||||
#
|
||||
# CONFIG_STM32_ETH_REMAP is not set
|
||||
# CONFIG_STM32_USART1_REMAP is not set
|
||||
# CONFIG_STM32_JTAG_DISABLE is not set
|
||||
CONFIG_STM32_JTAG_FULL_ENABLE=y
|
||||
# CONFIG_STM32_JTAG_NOJNTRST_ENABLE is not set
|
||||
# CONFIG_STM32_JTAG_SW_ENABLE is not set
|
||||
# CONFIG_STM32_DISABLE_IDLE_SLEEP_DURING_DEBUG is not set
|
||||
# CONFIG_STM32_FORCEPOWER is not set
|
||||
# CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG is not set
|
||||
CONFIG_STM32_USART=y
|
||||
|
||||
#
|
||||
# U[S]ART Configuration
|
||||
#
|
||||
# CONFIG_USART1_RS485 is not set
|
||||
# CONFIG_SERIAL_DISABLE_REORDERING is not set
|
||||
# CONFIG_STM32_USART_SINGLEWIRE is not set
|
||||
|
||||
#
|
||||
# Ethernet MAC configuration
|
||||
#
|
||||
CONFIG_STM32_PHYADDR=1
|
||||
# CONFIG_STM32_PHYINIT is not set
|
||||
# CONFIG_STM32_MII is not set
|
||||
CONFIG_STM32_AUTONEG=y
|
||||
CONFIG_STM32_PHYSR=16
|
||||
# CONFIG_STM32_PHYSR_ALTCONFIG is not set
|
||||
CONFIG_STM32_PHYSR_SPEED=0x0002
|
||||
CONFIG_STM32_PHYSR_100MBPS=0x0000
|
||||
CONFIG_STM32_PHYSR_MODE=0x0004
|
||||
CONFIG_STM32_PHYSR_FULLDUPLEX=0x0004
|
||||
# CONFIG_STM32_ETH_PTP is not set
|
||||
CONFIG_STM32_RMII=y
|
||||
# CONFIG_STM32_RMII_MCO is not set
|
||||
CONFIG_STM32_RMII_EXTCLK=y
|
||||
|
||||
#
|
||||
# USB Host Configuration
|
||||
#
|
||||
|
||||
#
|
||||
# USB Device Configuration
|
||||
#
|
||||
|
||||
#
|
||||
# Architecture Options
|
||||
#
|
||||
# CONFIG_ARCH_NOINTC is not set
|
||||
# CONFIG_ARCH_VECNOTIRQ is not set
|
||||
# CONFIG_ARCH_DMA is not set
|
||||
CONFIG_ARCH_HAVE_IRQPRIO=y
|
||||
# CONFIG_CUSTOM_STACK is not set
|
||||
# CONFIG_ADDRENV is not set
|
||||
CONFIG_ARCH_HAVE_VFORK=y
|
||||
CONFIG_ARCH_IRQPRIO=y
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
# CONFIG_ENDIAN_BIG is not set
|
||||
# CONFIG_ARCH_HAVE_RAMFUNCS is not set
|
||||
CONFIG_ARCH_HAVE_RAMVECTORS=y
|
||||
# CONFIG_ARCH_RAMVECTORS is not set
|
||||
|
||||
#
|
||||
# Board Settings
|
||||
#
|
||||
CONFIG_BOARD_LOOPSPERMSEC=5483
|
||||
# CONFIG_ARCH_CALIBRATION is not set
|
||||
|
||||
#
|
||||
# Interrupt options
|
||||
#
|
||||
CONFIG_ARCH_HAVE_INTERRUPTSTACK=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=0
|
||||
CONFIG_ARCH_HAVE_HIPRI_INTERRUPT=y
|
||||
# CONFIG_ARCH_HIPRI_INTERRUPT is not set
|
||||
|
||||
#
|
||||
# Boot options
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMEXTSRAM is not set
|
||||
CONFIG_BOOT_RUNFROMFLASH=y
|
||||
# CONFIG_BOOT_RUNFROMISRAM is not set
|
||||
# CONFIG_BOOT_RUNFROMSDRAM is not set
|
||||
# CONFIG_BOOT_COPYTORAM is not set
|
||||
|
||||
#
|
||||
# Boot Memory Configuration
|
||||
#
|
||||
CONFIG_RAM_START=0x20000000
|
||||
CONFIG_RAM_SIZE=65536
|
||||
|
||||
#
|
||||
# Board Selection
|
||||
#
|
||||
# CONFIG_ARCH_BOARD_CLOUDCTRL is not set
|
||||
# CONFIG_ARCH_BOARD_OLIMEX_STM32P107 is not set
|
||||
# CONFIG_ARCH_BOARD_SHENZHOU is not set
|
||||
CONFIG_ARCH_BOARD_VIEWTOOL_STM32F107=y
|
||||
# CONFIG_ARCH_BOARD_CUSTOM is not set
|
||||
CONFIG_ARCH_BOARD="viewtool-stm32f107"
|
||||
|
||||
#
|
||||
# Common Board Options
|
||||
#
|
||||
CONFIG_ARCH_HAVE_LEDS=y
|
||||
CONFIG_ARCH_LEDS=y
|
||||
CONFIG_ARCH_HAVE_BUTTONS=y
|
||||
# CONFIG_ARCH_BUTTONS is not set
|
||||
CONFIG_NSH_MMCSDMINOR=0
|
||||
|
||||
#
|
||||
# Board-Specific Options
|
||||
#
|
||||
|
||||
#
|
||||
# RTOS Features
|
||||
#
|
||||
# CONFIG_BOARD_INITIALIZE is not set
|
||||
CONFIG_MSEC_PER_TICK=10
|
||||
# CONFIG_SYSTEM_TIME64 is not set
|
||||
CONFIG_RR_INTERVAL=200
|
||||
# CONFIG_SCHED_INSTRUMENTATION is not set
|
||||
CONFIG_TASK_NAME_SIZE=0
|
||||
# CONFIG_SCHED_HAVE_PARENT is not set
|
||||
# CONFIG_JULIAN_TIME is not set
|
||||
CONFIG_START_YEAR=2009
|
||||
CONFIG_START_MONTH=9
|
||||
CONFIG_START_DAY=21
|
||||
CONFIG_DEV_CONSOLE=y
|
||||
# CONFIG_MUTEX_TYPES is not set
|
||||
# CONFIG_PRIORITY_INHERITANCE is not set
|
||||
# CONFIG_FDCLONE_DISABLE is not set
|
||||
# CONFIG_FDCLONE_STDIO is not set
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
# CONFIG_SCHED_WAITPID is not set
|
||||
# CONFIG_SCHED_STARTHOOK is not set
|
||||
# CONFIG_SCHED_ATEXIT is not set
|
||||
# CONFIG_SCHED_ONEXIT is not set
|
||||
CONFIG_USER_ENTRYPOINT="nsh_main"
|
||||
CONFIG_DISABLE_OS_API=y
|
||||
# CONFIG_DISABLE_CLOCK is not set
|
||||
# CONFIG_DISABLE_POSIX_TIMERS is not set
|
||||
# CONFIG_DISABLE_PTHREAD is not set
|
||||
# CONFIG_DISABLE_SIGNALS is not set
|
||||
# CONFIG_DISABLE_MQUEUE is not set
|
||||
# CONFIG_DISABLE_ENVIRON is not set
|
||||
|
||||
#
|
||||
# Signal Numbers
|
||||
#
|
||||
CONFIG_SIG_SIGUSR1=1
|
||||
CONFIG_SIG_SIGUSR2=2
|
||||
CONFIG_SIG_SIGALARM=3
|
||||
CONFIG_SIG_SIGCONDTIMEDOUT=16
|
||||
CONFIG_SIG_SIGWORK=17
|
||||
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
CONFIG_MAX_TASKS=16
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=4
|
||||
CONFIG_NFILE_DESCRIPTORS=8
|
||||
CONFIG_NFILE_STREAMS=8
|
||||
CONFIG_NAME_MAX=32
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_MQ_MAXMSGSIZE=32
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_PREALLOC_WDOGS=4
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
CONFIG_IDLETHREAD_STACKSIZE=1024
|
||||
CONFIG_USERMAIN_STACKSIZE=2048
|
||||
CONFIG_PTHREAD_STACK_MIN=256
|
||||
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
||||
|
||||
#
|
||||
# Device Drivers
|
||||
#
|
||||
# CONFIG_DISABLE_POLL is not set
|
||||
CONFIG_DEV_NULL=y
|
||||
# CONFIG_DEV_ZERO is not set
|
||||
# CONFIG_LOOP is not set
|
||||
# CONFIG_RAMDISK is not set
|
||||
# CONFIG_CAN is not set
|
||||
# CONFIG_ARCH_HAVE_PWM_PULSECOUNT is not set
|
||||
# CONFIG_PWM is not set
|
||||
CONFIG_ARCH_HAVE_I2CRESET=y
|
||||
# CONFIG_I2C is not set
|
||||
# CONFIG_SPI is not set
|
||||
# CONFIG_I2S is not set
|
||||
# CONFIG_RTC is not set
|
||||
# CONFIG_WATCHDOG is not set
|
||||
# CONFIG_ANALOG is not set
|
||||
# CONFIG_AUDIO_DEVICES is not set
|
||||
# CONFIG_VIDEO_DEVICES is not set
|
||||
# CONFIG_BCH is not set
|
||||
# CONFIG_INPUT is not set
|
||||
# CONFIG_LCD is not set
|
||||
# CONFIG_MMCSD is not set
|
||||
# CONFIG_MTD is not set
|
||||
CONFIG_NETDEVICES=y
|
||||
|
||||
#
|
||||
# General Ethernet MAC Driver Options
|
||||
#
|
||||
# CONFIG_NETDEV_MULTINIC is not set
|
||||
|
||||
#
|
||||
# External Ethernet MAC Device Support
|
||||
#
|
||||
# CONFIG_NET_DM90x0 is not set
|
||||
# CONFIG_ENC28J60 is not set
|
||||
# CONFIG_ENCX24J600 is not set
|
||||
# CONFIG_NET_E1000 is not set
|
||||
# CONFIG_NET_SLIP is not set
|
||||
# CONFIG_NET_VNET is not set
|
||||
|
||||
#
|
||||
# External Ethernet PHY Device Support
|
||||
#
|
||||
# CONFIG_ETH0_PHY_NONE is not set
|
||||
# CONFIG_ETH0_PHY_KS8721 is not set
|
||||
# CONFIG_ETH0_PHY_KSZ8051 is not set
|
||||
# CONFIG_ETH0_PHY_KSZ90x1 is not set
|
||||
CONFIG_ETH0_PHY_DP83848C=y
|
||||
# CONFIG_ETH0_PHY_LAN8720 is not set
|
||||
# CONFIG_ETH0_PHY_DM9161 is not set
|
||||
# CONFIG_PIPES is not set
|
||||
# CONFIG_PM is not set
|
||||
# CONFIG_POWER is not set
|
||||
# CONFIG_SENSORS is not set
|
||||
# CONFIG_SERCOMM_CONSOLE is not set
|
||||
CONFIG_SERIAL=y
|
||||
# CONFIG_DEV_LOWCONSOLE is not set
|
||||
# CONFIG_16550_UART is not set
|
||||
CONFIG_ARCH_HAVE_USART1=y
|
||||
|
||||
#
|
||||
# USART Configuration
|
||||
#
|
||||
CONFIG_USART1_ISUART=y
|
||||
CONFIG_MCU_SERIAL=y
|
||||
CONFIG_STANDARD_SERIAL=y
|
||||
CONFIG_SERIAL_NPOLLWAITERS=2
|
||||
CONFIG_USART1_SERIAL_CONSOLE=y
|
||||
# CONFIG_NO_SERIAL_CONSOLE is not set
|
||||
|
||||
#
|
||||
# USART1 Configuration
|
||||
#
|
||||
CONFIG_USART1_RXBUFSIZE=256
|
||||
CONFIG_USART1_TXBUFSIZE=256
|
||||
CONFIG_USART1_BAUD=115200
|
||||
CONFIG_USART1_BITS=8
|
||||
CONFIG_USART1_PARITY=0
|
||||
CONFIG_USART1_2STOP=0
|
||||
# CONFIG_USART1_IFLOWCONTROL is not set
|
||||
# CONFIG_USART1_OFLOWCONTROL is not set
|
||||
# CONFIG_SERIAL_IFLOWCONTROL is not set
|
||||
# CONFIG_SERIAL_OFLOWCONTROL is not set
|
||||
# CONFIG_USBDEV is not set
|
||||
# CONFIG_USBHOST is not set
|
||||
# CONFIG_WIRELESS is not set
|
||||
|
||||
#
|
||||
# System Logging Device Options
|
||||
#
|
||||
|
||||
#
|
||||
# System Logging
|
||||
#
|
||||
# CONFIG_RAMLOG is not set
|
||||
|
||||
#
|
||||
# Networking Support
|
||||
#
|
||||
CONFIG_ARCH_HAVE_NET=y
|
||||
CONFIG_ARCH_HAVE_PHY=y
|
||||
CONFIG_NET=y
|
||||
# CONFIG_NET_NOINTS is not set
|
||||
CONFIG_NET_MULTIBUFFER=y
|
||||
# CONFIG_NET_PROMISCUOUS is not set
|
||||
# CONFIG_NET_IPv6 is not set
|
||||
CONFIG_NSOCKET_DESCRIPTORS=10
|
||||
CONFIG_NET_NACTIVESOCKETS=16
|
||||
CONFIG_NET_SOCKOPTS=y
|
||||
CONFIG_NET_BUFSIZE=650
|
||||
# CONFIG_NET_TCPURGDATA is not set
|
||||
|
||||
#
|
||||
# TCP/IP Networking
|
||||
#
|
||||
CONFIG_NET_TCP=y
|
||||
CONFIG_NET_TCP_CONNS=40
|
||||
CONFIG_NET_MAX_LISTENPORTS=40
|
||||
CONFIG_NET_TCP_READAHEAD_BUFSIZE=650
|
||||
CONFIG_NET_NTCP_READAHEAD_BUFFERS=8
|
||||
CONFIG_NET_TCP_RECVDELAY=0
|
||||
# CONFIG_NET_TCPBACKLOG is not set
|
||||
# CONFIG_NET_TCP_SPLIT is not set
|
||||
# CONFIG_NET_SENDFILE is not set
|
||||
|
||||
#
|
||||
# UDP Networking
|
||||
#
|
||||
CONFIG_NET_UDP=y
|
||||
# CONFIG_NET_UDP_CHECKSUMS is not set
|
||||
CONFIG_NET_UDP_CONNS=8
|
||||
# CONFIG_NET_BROADCAST is not set
|
||||
# CONFIG_NET_RXAVAIL is not set
|
||||
CONFIG_NET_ICMP=y
|
||||
CONFIG_NET_ICMP_PING=y
|
||||
# CONFIG_NET_PINGADDRCONF is not set
|
||||
# CONFIG_NET_IGMP is not set
|
||||
# CONFIG_NET_STATISTICS is not set
|
||||
CONFIG_NET_RECEIVE_WINDOW=650
|
||||
CONFIG_NET_ARPTAB_SIZE=16
|
||||
# CONFIG_NET_ARP_IPIN is not set
|
||||
# CONFIG_NET_ROUTE is not set
|
||||
|
||||
#
|
||||
# File Systems
|
||||
#
|
||||
|
||||
#
|
||||
# File system configuration
|
||||
#
|
||||
# CONFIG_DISABLE_MOUNTPOINT is not set
|
||||
# CONFIG_FS_READABLE is not set
|
||||
# CONFIG_FS_WRITABLE is not set
|
||||
# CONFIG_FS_RAMMAP is not set
|
||||
# CONFIG_FS_FAT is not set
|
||||
# CONFIG_NFS is not set
|
||||
# CONFIG_FS_NXFFS is not set
|
||||
# CONFIG_FS_ROMFS is not set
|
||||
# CONFIG_FS_SMARTFS is not set
|
||||
# CONFIG_FS_BINFS is not set
|
||||
# CONFIG_FS_PROCFS is not set
|
||||
|
||||
#
|
||||
# System Logging
|
||||
#
|
||||
# CONFIG_SYSLOG_ENABLE is not set
|
||||
# CONFIG_SYSLOG is not set
|
||||
|
||||
#
|
||||
# Graphics Support
|
||||
#
|
||||
# CONFIG_NX is not set
|
||||
|
||||
#
|
||||
# Memory Management
|
||||
#
|
||||
# CONFIG_MM_MULTIHEAP is not set
|
||||
# CONFIG_MM_SMALL is not set
|
||||
CONFIG_MM_REGIONS=1
|
||||
# CONFIG_GRAN is not set
|
||||
|
||||
#
|
||||
# Audio Support
|
||||
#
|
||||
# CONFIG_AUDIO is not set
|
||||
|
||||
#
|
||||
# Binary Formats
|
||||
#
|
||||
# CONFIG_BINFMT_DISABLE is not set
|
||||
# CONFIG_BINFMT_EXEPATH is not set
|
||||
# CONFIG_NXFLAT is not set
|
||||
# CONFIG_ELF is not set
|
||||
CONFIG_BUILTIN=y
|
||||
# CONFIG_PIC is not set
|
||||
# CONFIG_SYMTAB_ORDEREDBYNAME is not set
|
||||
|
||||
#
|
||||
# Library Routines
|
||||
#
|
||||
|
||||
#
|
||||
# Standard C Library Options
|
||||
#
|
||||
CONFIG_STDIO_BUFFER_SIZE=64
|
||||
CONFIG_STDIO_LINEBUFFER=y
|
||||
CONFIG_NUNGET_CHARS=2
|
||||
CONFIG_LIB_HOMEDIR="/"
|
||||
# CONFIG_LIBM is not set
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH is not set
|
||||
# CONFIG_LIBC_FLOATINGPOINT is not set
|
||||
CONFIG_LIB_RAND_ORDER=1
|
||||
# CONFIG_EOL_IS_CR is not set
|
||||
# CONFIG_EOL_IS_LF is not set
|
||||
# CONFIG_EOL_IS_BOTH_CRLF is not set
|
||||
CONFIG_EOL_IS_EITHER_CRLF=y
|
||||
# CONFIG_LIBC_EXECFUNCS is not set
|
||||
CONFIG_POSIX_SPAWN_PROXY_STACKSIZE=1024
|
||||
CONFIG_TASK_SPAWN_DEFAULT_STACKSIZE=2048
|
||||
# CONFIG_LIBC_STRERROR is not set
|
||||
# CONFIG_LIBC_PERROR_STDOUT is not set
|
||||
CONFIG_ARCH_LOWPUTC=y
|
||||
CONFIG_LIB_SENDFILE_BUFSIZE=512
|
||||
# CONFIG_ARCH_ROMGETC is not set
|
||||
# CONFIG_ARCH_OPTIMIZED_FUNCTIONS is not set
|
||||
|
||||
#
|
||||
# Non-standard Library Support
|
||||
#
|
||||
CONFIG_SCHED_WORKQUEUE=y
|
||||
CONFIG_SCHED_HPWORK=y
|
||||
CONFIG_SCHED_WORKPRIORITY=192
|
||||
CONFIG_SCHED_WORKPERIOD=50000
|
||||
CONFIG_SCHED_WORKSTACKSIZE=1024
|
||||
# CONFIG_SCHED_LPWORK is not set
|
||||
# CONFIG_LIB_KBDCODEC is not set
|
||||
# CONFIG_LIB_SLCDCODEC is not set
|
||||
|
||||
#
|
||||
# Basic CXX Support
|
||||
#
|
||||
# CONFIG_C99_BOOL8 is not set
|
||||
# CONFIG_HAVE_CXX is not set
|
||||
|
||||
#
|
||||
# Application Configuration
|
||||
#
|
||||
|
||||
#
|
||||
# Built-In Applications
|
||||
#
|
||||
CONFIG_BUILTIN_PROXY_STACKSIZE=1024
|
||||
|
||||
#
|
||||
# Examples
|
||||
#
|
||||
# CONFIG_EXAMPLES_BUTTONS is not set
|
||||
# CONFIG_EXAMPLES_CAN is not set
|
||||
# CONFIG_EXAMPLES_CONFIGDATA is not set
|
||||
# CONFIG_EXAMPLES_DHCPD is not set
|
||||
# CONFIG_EXAMPLES_ELF is not set
|
||||
# CONFIG_EXAMPLES_FTPC is not set
|
||||
# CONFIG_EXAMPLES_FTPD is not set
|
||||
# CONFIG_EXAMPLES_HELLO is not set
|
||||
# CONFIG_EXAMPLES_HELLOXX is not set
|
||||
# CONFIG_EXAMPLES_JSON is not set
|
||||
# CONFIG_EXAMPLES_HIDKBD is not set
|
||||
# CONFIG_EXAMPLES_KEYPADTEST is not set
|
||||
# CONFIG_EXAMPLES_IGMP is not set
|
||||
# CONFIG_EXAMPLES_LCDRW is not set
|
||||
# CONFIG_EXAMPLES_MM is not set
|
||||
# CONFIG_EXAMPLES_MODBUS is not set
|
||||
# CONFIG_EXAMPLES_MOUNT is not set
|
||||
# CONFIG_EXAMPLES_NETTEST is not set
|
||||
# CONFIG_EXAMPLES_NRF24L01TERM is not set
|
||||
CONFIG_EXAMPLES_NSH=y
|
||||
# CONFIG_EXAMPLES_NULL is not set
|
||||
# CONFIG_EXAMPLES_NX is not set
|
||||
# CONFIG_EXAMPLES_NXCONSOLE is not set
|
||||
# CONFIG_EXAMPLES_NXFFS is not set
|
||||
# CONFIG_EXAMPLES_NXFLAT is not set
|
||||
# CONFIG_EXAMPLES_NXHELLO is not set
|
||||
# CONFIG_EXAMPLES_NXIMAGE is not set
|
||||
# CONFIG_EXAMPLES_NXLINES is not set
|
||||
# CONFIG_EXAMPLES_NXTEXT is not set
|
||||
# CONFIG_EXAMPLES_OSTEST is not set
|
||||
# CONFIG_EXAMPLES_PASHELLO is not set
|
||||
# CONFIG_EXAMPLES_PIPE is not set
|
||||
# CONFIG_EXAMPLES_POSIXSPAWN is not set
|
||||
# CONFIG_EXAMPLES_QENCODER is not set
|
||||
# CONFIG_EXAMPLES_RGMP is not set
|
||||
# CONFIG_EXAMPLES_ROMFS is not set
|
||||
# CONFIG_EXAMPLES_SENDMAIL is not set
|
||||
# CONFIG_EXAMPLES_SERLOOP is not set
|
||||
# CONFIG_EXAMPLES_SLCD is not set
|
||||
# CONFIG_EXAMPLES_SMART_TEST is not set
|
||||
# CONFIG_EXAMPLES_SMART is not set
|
||||
# CONFIG_EXAMPLES_TCPECHO is not set
|
||||
# CONFIG_EXAMPLES_TELNETD is not set
|
||||
# CONFIG_EXAMPLES_THTTPD is not set
|
||||
# CONFIG_EXAMPLES_TIFF is not set
|
||||
# CONFIG_EXAMPLES_TOUCHSCREEN is not set
|
||||
# CONFIG_EXAMPLES_UDP is not set
|
||||
# CONFIG_EXAMPLES_DISCOVER is not set
|
||||
# CONFIG_EXAMPLES_UIP is not set
|
||||
# CONFIG_EXAMPLES_USBSERIAL is not set
|
||||
# CONFIG_EXAMPLES_USBTERM is not set
|
||||
# CONFIG_EXAMPLES_WATCHDOG is not set
|
||||
# CONFIG_EXAMPLES_XMLRPC is not set
|
||||
|
||||
#
|
||||
# Graphics Support
|
||||
#
|
||||
# CONFIG_TIFF is not set
|
||||
|
||||
#
|
||||
# Interpreters
|
||||
#
|
||||
# CONFIG_INTERPRETERS_FICL is not set
|
||||
# CONFIG_INTERPRETERS_PCODE is not set
|
||||
|
||||
#
|
||||
# Network Utilities
|
||||
#
|
||||
|
||||
#
|
||||
# Networking Utilities
|
||||
#
|
||||
# CONFIG_NETUTILS_CODECS is not set
|
||||
# CONFIG_NETUTILS_DHCPC is not set
|
||||
# CONFIG_NETUTILS_DHCPD is not set
|
||||
# CONFIG_NETUTILS_FTPC is not set
|
||||
# CONFIG_NETUTILS_FTPD is not set
|
||||
# CONFIG_NETUTILS_JSON is not set
|
||||
CONFIG_NETUTILS_RESOLV=y
|
||||
CONFIG_NET_RESOLV_ENTRIES=8
|
||||
CONFIG_NET_RESOLV_MAXRESPONSE=96
|
||||
# CONFIG_NETUTILS_SMTP is not set
|
||||
# CONFIG_NETUTILS_TELNETD is not set
|
||||
CONFIG_NETUTILS_TFTPC=y
|
||||
# CONFIG_NETUTILS_THTTPD is not set
|
||||
CONFIG_NETUTILS_UIPLIB=y
|
||||
CONFIG_NETUTILS_WEBCLIENT=y
|
||||
CONFIG_NSH_WGET_USERAGENT="NuttX/6.xx.x (; http://www.nuttx.org/)"
|
||||
# CONFIG_NETUTILS_WEBSERVER is not set
|
||||
# CONFIG_NETUTILS_DISCOVER is not set
|
||||
# CONFIG_NETUTILS_XMLRPC is not set
|
||||
|
||||
#
|
||||
# FreeModBus
|
||||
#
|
||||
# CONFIG_MODBUS is not set
|
||||
|
||||
#
|
||||
# NSH Library
|
||||
#
|
||||
CONFIG_NSH_LIBRARY=y
|
||||
CONFIG_NSH_BUILTIN_APPS=y
|
||||
|
||||
#
|
||||
# Disable Individual commands
|
||||
#
|
||||
# CONFIG_NSH_DISABLE_ADDROUTE is not set
|
||||
# CONFIG_NSH_DISABLE_CAT is not set
|
||||
# CONFIG_NSH_DISABLE_CD is not set
|
||||
# CONFIG_NSH_DISABLE_CP is not set
|
||||
# CONFIG_NSH_DISABLE_CMP is not set
|
||||
# CONFIG_NSH_DISABLE_DD is not set
|
||||
# CONFIG_NSH_DISABLE_DELROUTE is not set
|
||||
# CONFIG_NSH_DISABLE_ECHO is not set
|
||||
# CONFIG_NSH_DISABLE_EXEC is not set
|
||||
# CONFIG_NSH_DISABLE_EXIT is not set
|
||||
# CONFIG_NSH_DISABLE_FREE is not set
|
||||
# CONFIG_NSH_DISABLE_GET is not set
|
||||
# CONFIG_NSH_DISABLE_HELP is not set
|
||||
# CONFIG_NSH_DISABLE_HEXDUMP is not set
|
||||
# CONFIG_NSH_DISABLE_IFCONFIG is not set
|
||||
# CONFIG_NSH_DISABLE_KILL is not set
|
||||
# CONFIG_NSH_DISABLE_LOSETUP is not set
|
||||
# CONFIG_NSH_DISABLE_LS is not set
|
||||
# CONFIG_NSH_DISABLE_MB is not set
|
||||
# CONFIG_NSH_DISABLE_MKDIR is not set
|
||||
# CONFIG_NSH_DISABLE_MKFATFS is not set
|
||||
# CONFIG_NSH_DISABLE_MKFIFO is not set
|
||||
# CONFIG_NSH_DISABLE_MKRD is not set
|
||||
# CONFIG_NSH_DISABLE_MH is not set
|
||||
# CONFIG_NSH_DISABLE_MOUNT is not set
|
||||
# CONFIG_NSH_DISABLE_MW is not set
|
||||
# CONFIG_NSH_DISABLE_NSFMOUNT is not set
|
||||
# CONFIG_NSH_DISABLE_PS is not set
|
||||
# CONFIG_NSH_DISABLE_PING is not set
|
||||
# CONFIG_NSH_DISABLE_PUT is not set
|
||||
# CONFIG_NSH_DISABLE_PWD is not set
|
||||
# CONFIG_NSH_DISABLE_RM is not set
|
||||
# CONFIG_NSH_DISABLE_RMDIR is not set
|
||||
# CONFIG_NSH_DISABLE_SET is not set
|
||||
# CONFIG_NSH_DISABLE_SH is not set
|
||||
# CONFIG_NSH_DISABLE_SLEEP is not set
|
||||
# CONFIG_NSH_DISABLE_TEST is not set
|
||||
# CONFIG_NSH_DISABLE_UMOUNT is not set
|
||||
# CONFIG_NSH_DISABLE_UNSET is not set
|
||||
# CONFIG_NSH_DISABLE_USLEEP is not set
|
||||
# CONFIG_NSH_DISABLE_WGET is not set
|
||||
# CONFIG_NSH_DISABLE_XD is not set
|
||||
|
||||
#
|
||||
# Configure Command Options
|
||||
#
|
||||
# CONFIG_NSH_CMDOPT_DF_H is not set
|
||||
CONFIG_NSH_CODECS_BUFSIZE=128
|
||||
# CONFIG_NSH_CMDOPT_HEXDUMP is not set
|
||||
CONFIG_NSH_FILEIOSIZE=1024
|
||||
CONFIG_NSH_LINELEN=80
|
||||
CONFIG_NSH_MAXARGUMENTS=6
|
||||
CONFIG_NSH_NESTDEPTH=3
|
||||
# CONFIG_NSH_DISABLESCRIPT is not set
|
||||
# CONFIG_NSH_DISABLEBG is not set
|
||||
CONFIG_NSH_CONSOLE=y
|
||||
|
||||
#
|
||||
# USB Trace Support
|
||||
#
|
||||
# CONFIG_NSH_CONDEV is not set
|
||||
# CONFIG_NSH_ARCHINIT is not set
|
||||
# CONFIG_NSH_TELNET is not set
|
||||
CONFIG_NSH_IPADDR=0x0a000002
|
||||
CONFIG_NSH_DRIPADDR=0x0a000001
|
||||
CONFIG_NSH_NETMASK=0xffffff00
|
||||
CONFIG_NSH_NOMAC=y
|
||||
CONFIG_NSH_MAX_ROUNDTRIP=20
|
||||
|
||||
#
|
||||
# NxWidgets/NxWM
|
||||
#
|
||||
|
||||
#
|
||||
# Platform-specific Support
|
||||
#
|
||||
# CONFIG_PLATFORM_CONFIGDATA is not set
|
||||
|
||||
#
|
||||
# System NSH Add-Ons
|
||||
#
|
||||
|
||||
#
|
||||
# USB CDC/ACM Device Commands
|
||||
#
|
||||
|
||||
#
|
||||
# USB Composite Device Commands
|
||||
#
|
||||
|
||||
#
|
||||
# Custom Free Memory Command
|
||||
#
|
||||
# CONFIG_SYSTEM_FREE is not set
|
||||
|
||||
#
|
||||
# I2C tool
|
||||
#
|
||||
|
||||
#
|
||||
# FLASH Program Installation
|
||||
#
|
||||
# CONFIG_SYSTEM_INSTALL is not set
|
||||
|
||||
#
|
||||
# FLASH Erase-all Command
|
||||
#
|
||||
|
||||
#
|
||||
# NxPlayer media player library / command Line
|
||||
#
|
||||
# CONFIG_SYSTEM_NXPLAYER is not set
|
||||
|
||||
#
|
||||
# RAM test
|
||||
#
|
||||
# CONFIG_SYSTEM_RAMTEST is not set
|
||||
|
||||
#
|
||||
# readline()
|
||||
#
|
||||
CONFIG_SYSTEM_READLINE=y
|
||||
CONFIG_READLINE_ECHO=y
|
||||
|
||||
#
|
||||
# Power Off
|
||||
#
|
||||
# CONFIG_SYSTEM_POWEROFF is not set
|
||||
|
||||
#
|
||||
# RAMTRON
|
||||
#
|
||||
# CONFIG_SYSTEM_RAMTRON is not set
|
||||
|
||||
#
|
||||
# SD Card
|
||||
#
|
||||
# CONFIG_SYSTEM_SDCARD is not set
|
||||
|
||||
#
|
||||
# Sysinfo
|
||||
#
|
||||
# CONFIG_SYSTEM_SYSINFO is not set
|
||||
|
||||
#
|
||||
# USB Monitor
|
||||
#
|
||||
|
||||
#
|
||||
# Stack Monitor
|
||||
#
|
||||
|
||||
#
|
||||
# USB Mass Storage Device Commands
|
||||
#
|
||||
|
||||
#
|
||||
# Zmodem Commands
|
||||
#
|
||||
# CONFIG_SYSTEM_ZMODEM is not set
|
||||
75
configs/viewtool-stm32f107/netnsh/setenv.sh
Executable file
75
configs/viewtool-stm32f107/netnsh/setenv.sh
Executable file
@ -0,0 +1,75 @@
|
||||
#!/bin/bash
|
||||
# configs/viewtool-stm32f107/netnsh/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2013 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$_" = "$0" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
WD=`pwd`
|
||||
if [ ! -x "setenv.sh" ]; then
|
||||
echo "This script must be executed from the top-level NuttX build directory"
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then
|
||||
export PATH_ORIG="${PATH}"
|
||||
fi
|
||||
|
||||
# This is the Cygwin path to the location where I installed the RIDE
|
||||
# toolchain under windows. You will also have to edit this if you install
|
||||
# the RIDE toolchain in any other location
|
||||
#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Raisonance/Ride/arm-gcc/bin"
|
||||
|
||||
# This is the Cygwin path to the location where I installed the CodeSourcery
|
||||
# toolchain under windows. You will also have to edit this if you install
|
||||
# the CodeSourcery toolchain in any other location
|
||||
export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
|
||||
|
||||
# These are the Cygwin paths to the locations where I installed the Atollic
|
||||
# toolchain under windows. You will also have to edit this if you install
|
||||
# the Atollic toolchain in any other location. /usr/bin is added before
|
||||
# the Atollic bin path because there is are binaries named gcc.exe and g++.exe
|
||||
# at those locations as well.
|
||||
#export TOOLCHAIN_BIN="/usr/bin:/cygdrive/c/Program Files (x86)/Atollic/TrueSTUDIO for ARM Pro 2.3.0/ARMTools/bin"
|
||||
#export TOOLCHAIN_BIN="/usr/bin:/cygdrive/c/Program Files (x86)/Atollic/TrueSTUDIO for STMicroelectronics STM32 Lite 2.3.0/ARMTools/bin"
|
||||
|
||||
# This is the Cygwin path to the location where I build the buildroot
|
||||
# toolchain.
|
||||
#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
|
||||
# Add the path to the toolchain to the PATH varialble
|
||||
export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
||||
@ -296,10 +296,10 @@ void stm32_setled(int led, bool ledon)
|
||||
void stm32_setleds(uint8_t ledset)
|
||||
{
|
||||
#ifdef CONFIG_ARCH_LEDS
|
||||
led_offbits(ledset & ~BOARD_LED4_BIT);
|
||||
led_onbits(ledset & ~BOARD_LED4_BIT);
|
||||
led_offbits(~(ledset | BOARD_LED4_BIT));
|
||||
#else
|
||||
led_offbits(ledset);
|
||||
led_onbits(ledset);
|
||||
led_offbits(~ledset);
|
||||
#endif
|
||||
}
|
||||
|
||||
Loading…
Reference in New Issue
Block a user