diff --git a/drivers/wireless/ieee80211/Kconfig b/drivers/wireless/ieee80211/Kconfig index a38f67daf8..43a02237c5 100644 --- a/drivers/wireless/ieee80211/Kconfig +++ b/drivers/wireless/ieee80211/Kconfig @@ -22,4 +22,30 @@ config IEEE80211_BROADCOM_FULLMAC_SDIO This selection enables support for broadcom FullMAC-compliant devices using SDIO bus. +choice + prompt "Broadcom 43362 driver work queue" + default IEEE80211_BROADCOM_LPWORK if SCHED_LPWORK + default IEEE80211_BROADCOM_HPWORK if !SCHED_LPWORK && SCHED_HPWORK + depends on SCHED_WORKQUEUE + ---help--- + Work queue support is required to use the loopback driver. If the + low priority work queue is available, then it should be used by the + loopback driver. + +config IEEE80211_BROADCOM_HPWORK + bool "High priority" + depends on SCHED_HPWORK + +config IEEE80211_BROADCOM_LPWORK + bool "Low priority" + depends on SCHED_LPWORK + +endchoice # Work queue +endif # NETDEV_IEEE80211_BROADCOM_ + +config IEEE80211_BROADCOM_NINTERFACES + int "Nubmer of Broadcom 43362 interfaces" + default 1 + depends on EXPERIMENTAL + endif # DRIVERS_IEEE80211 diff --git a/drivers/wireless/ieee80211/bcmf_netdev.c b/drivers/wireless/ieee80211/bcmf_netdev.c new file mode 100644 index 0000000000..74ab9da801 --- /dev/null +++ b/drivers/wireless/ieee80211/bcmf_netdev.c @@ -0,0 +1,1187 @@ +/**************************************************************************** + * drivers/wireless/bcmf_netdev.c + * + * Copyright (C) 2017 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include +#if defined(CONFIG_NET) && defined(CONFIG_IEEE80211_BROADCOM_FULLMAC) + +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include +#include +#include +#include +#include + +#ifdef CONFIG_NET_PKT +# include +#endif + +/**************************************************************************** + * Pre-processor Definitions + ****************************************************************************/ + +/* If processing is not done at the interrupt level, then work queue support + * is required. + */ + +#if !defined(CONFIG_SCHED_WORKQUEUE) +# error Work queue support is required in this configuration (CONFIG_SCHED_WORKQUEUE) +#else + + /* Use the selected work queue */ + +# if defined(CONFIG_IEEE80211_BROADCOM_HPWORK) +# define BCMFWORK HPWORK +# elif defined(CONFIG_IEEE80211_BROADCOM_HLWORK) +# define BCMFWORK LPWORK +# else +# error Neither CONFIG_IEEE80211_BROADCOM_HPWORK nor CONFIG_IEEE80211_BROADCOM_HLWORK defined +# endif +#endif + +/* CONFIG_IEEE80211_BROADCOM_NINTERFACES determines the number of physical interfaces + * that will be supported. + */ + +#ifndef CONFIG_IEEE80211_BROADCOM_NINTERFACES +# define CONFIG_IEEE80211_BROADCOM_NINTERFACES 1 +#endif + +/* TX poll delay = 1 seconds. CLK_TCK is the number of clock ticks per second */ + +#define BCMF_WDDELAY (1*CLK_TCK) + +/* TX timeout = 1 minute */ + +#define BCMF_TXTIMEOUT (60*CLK_TCK) + +/* This is a helper pointer for accessing the contents of the Ethernet header */ + +#define BUF ((struct eth_hdr_s *)priv->bc_dev.d_buf) + +/**************************************************************************** + * Private Types + ****************************************************************************/ + +/* The bcmf_driver_s encapsulates all state information for a single hardware + * interface + */ + +struct bcmf_driver_s +{ + bool bc_bifup; /* true:ifup false:ifdown */ + WDOG_ID bc_txpoll; /* TX poll timer */ + WDOG_ID bc_txtimeout; /* TX timeout timer */ + struct work_s bc_irqwork; /* For deferring interupt work to the work queue */ + struct work_s bc_pollwork; /* For deferring poll work to the work queue */ + + /* This holds the information visible to the NuttX network */ + + struct net_driver_s bc_dev; /* Interface understood by the network */ +}; + +/**************************************************************************** + * Private Data + ****************************************************************************/ + +/* These statically allocated structur would mean that only a single + * instance of the device could be supported. In order to support multiple + * devices instances, this data would have to be allocated dynamically. + */ + +/* A single packet buffer per device is used here. There might be multiple + * packet buffers in a more complex, pipelined design. + * + * NOTE that if CONFIG_IEEE80211_BROADCOM_NINTERFACES were greater than 1, you would + * need a minimum on one packetbuffer per instance. Much better to be + * allocated dynamically. + */ + +static uint8_t g_pktbuf[MAX_NET_DEV_MTU + CONFIG_NET_GUARDSIZE]; + +/* Driver state structure */ + +static struct bcmf_driver_s g_bcmf_interface[CONFIG_IEEE80211_BROADCOM_NINTERFACES]; + +/**************************************************************************** + * Private Function Prototypes + ****************************************************************************/ + +/* Common TX logic */ + +static int bcmf_transmit(FAR struct bcmf_driver_s *priv); +static int bcmf_txpoll(FAR struct net_driver_s *dev); + +/* Interrupt handling */ + +static void bcmf_receive(FAR struct bcmf_driver_s *priv); +static void bcmf_txdone(FAR struct bcmf_driver_s *priv); + +static void bcmf_interrupt_work(FAR void *arg); +static int bcmf_interrupt(int irq, FAR void *context, FAR void *arg); + +/* Watchdog timer expirations */ + +static void bcmf_txtimeout_work(FAR void *arg); +static void bcmf_txtimeout_expiry(int argc, wdparm_t arg, ...); + +static void bcmf_poll_work(FAR void *arg); +static void bcmf_poll_expiry(int argc, wdparm_t arg, ...); + +/* NuttX callback functions */ + +static int bcmf_ifup(FAR struct net_driver_s *dev); +static int bcmf_ifdown(FAR struct net_driver_s *dev); + +static void bcmf_txavail_work(FAR void *arg); +static int bcmf_txavail(FAR struct net_driver_s *dev); + +#if defined(CONFIG_NET_IGMP) || defined(CONFIG_NET_ICMPv6) +static int bcmf_addmac(FAR struct net_driver_s *dev, + FAR const uint8_t *mac); +#ifdef CONFIG_NET_IGMP +static int bcmf_rmmac(FAR struct net_driver_s *dev, + FAR const uint8_t *mac); +#endif +#ifdef CONFIG_NET_ICMPv6 +static void bcmf_ipv6multicast(FAR struct bcmf_driver_s *priv); +#endif +#endif +#ifdef CONFIG_NETDEV_IOCTL +static int bcmf_ioctl(FAR struct net_driver_s *dev, int cmd, + unsigned long arg); +#endif + +/**************************************************************************** + * Private Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: bcmf_transmit + * + * Description: + * Start hardware transmission. Called either from the txdone interrupt + * handling or from watchdog based polling. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * OK on success; a negated errno on failure + * + * Assumptions: + * May or may not be called from an interrupt handler. In either case, + * the network is locked. + * + ****************************************************************************/ + +static int bcmf_transmit(FAR struct bcmf_driver_s *priv) +{ + /* Verify that the hardware is ready to send another packet. If we get + * here, then we are committed to sending a packet; Higher level logic + * must have assured that there is no transmission in progress. + */ + + /* Increment statistics */ + + NETDEV_TXPACKETS(priv->bc_dev); + + /* Send the packet: address=priv->bc_dev.d_buf, length=priv->bc_dev.d_len */ + + /* Enable Tx interrupts */ + + /* Setup the TX timeout watchdog (perhaps restarting the timer) */ + + (void)wd_start(priv->bc_txtimeout, BCMF_TXTIMEOUT, + bcmf_txtimeout_expiry, 1, (wdparm_t)priv); + return OK; +} + +/**************************************************************************** + * Name: bcmf_txpoll + * + * Description: + * The transmitter is available, check if the network has any outgoing + * packets ready to send. This is a callback from devif_poll(). + * devif_poll() may be called: + * + * 1. When the preceding TX packet send is complete, + * 2. When the preceding TX packet send timesout and the interface is reset + * 3. During normal TX polling + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * + * Returned Value: + * OK on success; a negated errno on failure + * + * Assumptions: + * May or may not be called from an interrupt handler. In either case, + * the network is locked. + * + ****************************************************************************/ + +static int bcmf_txpoll(FAR struct net_driver_s *dev) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)dev->d_private; + + /* If the polling resulted in data that should be sent out on the network, + * the field d_len is set to a value > 0. + */ + + if (priv->bc_dev.d_len > 0) + { + /* Look up the destination MAC address and add it to the Ethernet + * header. + */ + +#ifdef CONFIG_NET_IPv4 +#ifdef CONFIG_NET_IPv6 + if (IFF_IS_IPv4(priv->bc_dev.d_flags)) +#endif + { + arp_out(&priv->bc_dev); + } +#endif /* CONFIG_NET_IPv4 */ + +#ifdef CONFIG_NET_IPv6 +#ifdef CONFIG_NET_IPv4 + else +#endif + { + neighbor_out(&priv->bc_dev); + } +#endif /* CONFIG_NET_IPv6 */ + + /* Send the packet */ + + bcmf_transmit(priv); + + /* Check if there is room in the device to hold another packet. If not, + * return a non-zero value to terminate the poll. + */ + } + + /* If zero is returned, the polling will continue until all connections have + * been examined. + */ + + return 0; +} + +/**************************************************************************** + * Name: bcmf_receive + * + * Description: + * An interrupt was received indicating the availability of a new RX packet + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * The network is locked. + * + ****************************************************************************/ + +static void bcmf_receive(FAR struct bcmf_driver_s *priv) +{ + do + { + /* Check for errors and update statistics */ + + /* Check if the packet is a valid size for the network buffer + * configuration. + */ + + /* Copy the data data from the hardware to priv->bc_dev.d_buf. Set + * amount of data in priv->bc_dev.d_len + */ + +#ifdef CONFIG_NET_PKT + /* When packet sockets are enabled, feed the frame into the packet tap */ + + pkt_input(&priv->bc_dev); +#endif + + /* We only accept IP packets of the configured type and ARP packets */ + +#ifdef CONFIG_NET_IPv4 + if (BUF->type == HTONS(ETHTYPE_IP)) + { + ninfo("IPv4 frame\n"); + NETDEV_RXIPV4(&priv->bc_dev); + + /* Handle ARP on input then give the IPv4 packet to the network + * layer + */ + + arp_ipin(&priv->bc_dev); + ipv4_input(&priv->bc_dev); + + /* If the above function invocation resulted in data that should be + * sent out on the network, the field d_len will set to a value > 0. + */ + + if (priv->bc_dev.d_len > 0) + { + /* Update the Ethernet header with the correct MAC address */ + +#ifdef CONFIG_NET_IPv6 + if (IFF_IS_IPv4(priv->bc_dev.d_flags)) +#endif + { + arp_out(&priv->bc_dev); + } +#ifdef CONFIG_NET_IPv6 + else + { + neighbor_out(&kel->bc_dev); + } +#endif + + /* And send the packet */ + + bcmf_transmit(priv); + } + } + else +#endif +#ifdef CONFIG_NET_IPv6 + if (BUF->type == HTONS(ETHTYPE_IP6)) + { + ninfo("Iv6 frame\n"); + NETDEV_RXIPV6(&priv->bc_dev); + + /* Give the IPv6 packet to the network layer */ + + ipv6_input(&priv->bc_dev); + + /* If the above function invocation resulted in data that should be + * sent out on the network, the field d_len will set to a value > 0. + */ + + if (priv->bc_dev.d_len > 0) + { + /* Update the Ethernet header with the correct MAC address */ + +#ifdef CONFIG_NET_IPv4 + if (IFF_IS_IPv4(priv->bc_dev.d_flags)) + { + arp_out(&priv->bc_dev); + } + else +#endif +#ifdef CONFIG_NET_IPv6 + { + neighbor_out(&priv->bc_dev); + } +#endif + + /* And send the packet */ + + bcmf_transmit(priv); + } + } + else +#endif +#ifdef CONFIG_NET_ARP + if (BUF->type == htons(ETHTYPE_ARP)) + { + arp_arpin(&priv->bc_dev); + NETDEV_RXARP(&priv->bc_dev); + + /* If the above function invocation resulted in data that should be + * sent out on the network, the field d_len will set to a value > 0. + */ + + if (priv->bc_dev.d_len > 0) + { + bcmf_transmit(priv); + } + } + else +#endif + { + NETDEV_RXDROPPED(&priv->bc_dev); + } + } + while (); /* While there are more packets to be processed */ +} + +/**************************************************************************** + * Name: bcmf_txdone + * + * Description: + * An interrupt was received indicating that the last TX packet(s) is done + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * The network is locked. + * + ****************************************************************************/ + +static void bcmf_txdone(FAR struct bcmf_driver_s *priv) +{ + int delay; + + /* Check for errors and update statistics */ + + NETDEV_TXDONE(priv->bc_dev); + + /* Check if there are pending transmissions */ + + /* If no further transmissions are pending, then cancel the TX timeout and + * disable further Tx interrupts. + */ + + wd_cancel(priv->bc_txtimeout); + + /* And disable further TX interrupts. */ + + /* In any event, poll the network for new TX data */ + + (void)devif_poll(&priv->bc_dev, bcmf_txpoll); +} + +/**************************************************************************** + * Name: bcmf_interrupt_work + * + * Description: + * Perform interrupt related work from the worker thread + * + * Parameters: + * arg - The argument passed when work_queue() was called. + * + * Returned Value: + * OK on success + * + * Assumptions: + * The network is locked. + * + ****************************************************************************/ + +static void bcmf_interrupt_work(FAR void *arg) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)arg; + + /* Lock the network and serialize driver operations if necessary. + * NOTE: Serialization is only required in the case where the driver work + * is performed on an LP worker thread and where more than one LP worker + * thread has been configured. + */ + + net_lock(); + + /* Process pending Ethernet interrupts */ + + /* Get and clear interrupt status bits */ + + /* Handle interrupts according to status bit settings */ + + /* Check if we received an incoming packet, if so, call bcmf_receive() */ + + bcmf_receive(priv); + + /* Check if a packet transmission just completed. If so, call bcmf_txdone. + * This may disable further Tx interrupts if there are no pending + * transmissions. + */ + + bcmf_txdone(priv); + net_unlock(); + + /* Re-enable Ethernet interrupts */ +#warning Missing logic +} + +/**************************************************************************** + * Name: bcmf_interrupt + * + * Description: + * Hardware interrupt handler + * + * Parameters: + * irq - Number of the IRQ that generated the interrupt + * context - Interrupt register state save info (architecture-specific) + * + * Returned Value: + * OK on success + * + * Assumptions: + * + ****************************************************************************/ + +static int bcmf_interrupt(int irq, FAR void *context, FAR void *arg) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)arg; + + DEBUGASSERT(priv != NULL); + + /* Disable further Ethernet interrupts. Because Ethernet interrupts are + * also disabled if the TX timeout event occurs, there can be no race + * condition here. + */ +#warning Missing logic + + /* TODO: Determine if a TX transfer just completed */ + + { + /* If a TX transfer just completed, then cancel the TX timeout so + * there will be no race condition between any subsequent timeout + * expiration and the deferred interrupt processing. + */ + + wd_cancel(priv->bc_txtimeout); + } + + /* Schedule to perform the interrupt processing on the worker thread. */ + + work_queue(BCMFWORK, &priv->bc_irqwork, bcmf_interrupt_work, priv, 0); + return OK; +} + +/**************************************************************************** + * Name: bcmf_txtimeout_work + * + * Description: + * Perform TX timeout related work from the worker thread + * + * Parameters: + * arg - The argument passed when work_queue() as called. + * + * Returned Value: + * OK on success + * + * Assumptions: + * The network is locked. + * + ****************************************************************************/ + +static void bcmf_txtimeout_work(FAR void *arg) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)arg; + + /* Lock the network and serialize driver operations if necessary. + * NOTE: Serialization is only required in the case where the driver work + * is performed on an LP worker thread and where more than one LP worker + * thread has been configured. + */ + + net_lock(); + + /* Increment statistics and dump debug info */ + + NETDEV_TXTIMEOUTS(priv->bc_dev); + + /* Then reset the hardware */ + + /* Then poll the network for new XMIT data */ + + (void)devif_poll(&priv->bc_dev, bcmf_txpoll); + net_unlock(); +} + +/**************************************************************************** + * Name: bcmf_txtimeout_expiry + * + * Description: + * Our TX watchdog timed out. Called from the timer interrupt handler. + * The last TX never completed. Reset the hardware and start again. + * + * Parameters: + * argc - The number of available arguments + * arg - The first argument + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by the watchdog logic. + * + ****************************************************************************/ + +static void bcmf_txtimeout_expiry(int argc, wdparm_t arg, ...) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)arg; + + /* Disable further Ethernet interrupts. This will prevent some race + * conditions with interrupt work. There is still a potential race + * condition with interrupt work that is already queued and in progress. + */ +#warning Missing logic + + /* Schedule to perform the TX timeout processing on the worker thread. */ + + work_queue(BCMFWORK, &priv->bc_irqwork, bcmf_txtimeout_work, priv, 0); +} + +/**************************************************************************** + * Name: bcmf_poll_process + * + * Description: + * Perform the periodic poll. This may be called either from watchdog + * timer logic or from the worker thread, depending upon the configuration. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +static inline void bcmf_poll_process(FAR struct bcmf_driver_s *priv) +{ +} + +/**************************************************************************** + * Name: bcmf_poll_work + * + * Description: + * Perform periodic polling from the worker thread + * + * Parameters: + * arg - The argument passed when work_queue() as called. + * + * Returned Value: + * OK on success + * + * Assumptions: + * The network is locked. + * + ****************************************************************************/ + +static void bcmf_poll_work(FAR void *arg) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)arg; + + /* Lock the network and serialize driver operations if necessary. + * NOTE: Serialization is only required in the case where the driver work + * is performed on an LP worker thread and where more than one LP worker + * thread has been configured. + */ + + net_lock(); + + /* Perform the poll */ + + /* Check if there is room in the send another TX packet. We cannot perform + * the TX poll if he are unable to accept another packet for transmission. + */ + + /* If so, update TCP timing states and poll the network for new XMIT data. + * Hmmm.. might be bug here. Does this mean if there is a transmit in + * progress, we will missing TCP time state updates? + */ + + (void)devif_timer(&priv->bc_dev, bcmf_txpoll); + + /* Setup the watchdog poll timer again */ + + (void)wd_start(priv->bc_txpoll, BCMF_WDDELAY, bcmf_poll_expiry, 1, + (wdparm_t)priv); + net_unlock(); +} + +/**************************************************************************** + * Name: bcmf_poll_expiry + * + * Description: + * Periodic timer handler. Called from the timer interrupt handler. + * + * Parameters: + * argc - The number of available arguments + * arg - The first argument + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by the watchdog logic. + * + ****************************************************************************/ + +static void bcmf_poll_expiry(int argc, wdparm_t arg, ...) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)arg; + + /* Schedule to perform the interrupt processing on the worker thread. */ + + work_queue(BCMFWORK, &priv->bc_pollwork, bcmf_poll_work, priv, 0); +} + +/**************************************************************************** + * Name: bcmf_ifup + * + * Description: + * NuttX Callback: Bring up the Ethernet interface when an IP address is + * provided + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +static int bcmf_ifup(FAR struct net_driver_s *dev) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)dev->d_private; + +#ifdef CONFIG_NET_IPv4 + ninfo("Bringing up: %d.%d.%d.%d\n", + dev->d_ipaddr & 0xff, (dev->d_ipaddr >> 8) & 0xff, + (dev->d_ipaddr >> 16) & 0xff, dev->d_ipaddr >> 24); +#endif +#ifdef CONFIG_NET_IPv6 + ninfo("Bringing up: %04x:%04x:%04x:%04x:%04x:%04x:%04x:%04x\n", + dev->d_ipv6addr[0], dev->d_ipv6addr[1], dev->d_ipv6addr[2], + dev->d_ipv6addr[3], dev->d_ipv6addr[4], dev->d_ipv6addr[5], + dev->d_ipv6addr[6], dev->d_ipv6addr[7]); +#endif + + /* Initialize PHYs, the Ethernet interface, and setup up Ethernet interrupts */ + + /* Instantiate the MAC address from priv->bc_dev.d_mac.ether.ether_addr_octet */ + +#ifdef CONFIG_NET_ICMPv6 + /* Set up IPv6 multicast address filtering */ + + bcmf_ipv6multicast(priv); +#endif + + /* Set and activate a timer process */ + + (void)wd_start(priv->bc_txpoll, BCMF_WDDELAY, bcmf_poll_expiry, 1, + (wdparm_t)priv); + + /* Enable the hardware interrupt */ + + priv->bc_bifup = true; +#warning Missing logic + return OK; +} + +/**************************************************************************** + * Name: bcmf_ifdown + * + * Description: + * NuttX Callback: Stop the interface. + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +static int bcmf_ifdown(FAR struct net_driver_s *dev) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)dev->d_private; + irqstate_t flags; + + /* Disable the hardware interrupt */ + + flags = enter_critical_section(); +#warning Missing logic + + /* Cancel the TX poll timer and TX timeout timers */ + + wd_cancel(priv->bc_txpoll); + wd_cancel(priv->bc_txtimeout); + + /* Put the EMAC in its reset, non-operational state. This should be + * a known configuration that will guarantee the bcmf_ifup() always + * successfully brings the interface back up. + */ + + /* Mark the device "down" */ + + priv->bc_bifup = false; + leave_critical_section(flags); + return OK; +} + +/**************************************************************************** + * Name: bcmf_txavail_work + * + * Description: + * Perform an out-of-cycle poll on the worker thread. + * + * Parameters: + * arg - Reference to the NuttX driver state structure (cast to void*) + * + * Returned Value: + * None + * + * Assumptions: + * Called on the higher priority worker thread. + * + ****************************************************************************/ + +static void bcmf_txavail_work(FAR void *arg) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)arg; + + /* Lock the network and serialize driver operations if necessary. + * NOTE: Serialization is only required in the case where the driver work + * is performed on an LP worker thread and where more than one LP worker + * thread has been configured. + */ + + net_lock(); + + /* Ignore the notification if the interface is not yet up */ + + if (priv->bc_bifup) + { + /* Check if there is room in the hardware to hold another outgoing packet. */ + + /* If so, then poll the network for new XMIT data */ + + (void)devif_poll(&priv->bc_dev, bcmf_txpoll); + } + + net_unlock(); +} + +/**************************************************************************** + * Name: bcmf_txavail + * + * Description: + * Driver callback invoked when new TX data is available. This is a + * stimulus perform an out-of-cycle poll and, thereby, reduce the TX + * latency. + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Called in normal user mode + * + ****************************************************************************/ + +static int bcmf_txavail(FAR struct net_driver_s *dev) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)dev->d_private; + + /* Is our single work structure available? It may not be if there are + * pending interrupt actions and we will have to ignore the Tx + * availability action. + */ + + if (work_available(&priv->bc_pollwork)) + { + /* Schedule to serialize the poll on the worker thread. */ + + work_queue(BCMFWORK, &priv->bc_pollwork, bcmf_txavail_work, priv, 0); + } + + return OK; +} + +/**************************************************************************** + * Name: bcmf_addmac + * + * Description: + * NuttX Callback: Add the specified MAC address to the hardware multicast + * address filtering + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * mac - The MAC address to be added + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +#if defined(CONFIG_NET_IGMP) || defined(CONFIG_NET_ICMPv6) +static int bcmf_addmac(FAR struct net_driver_s *dev, FAR const uint8_t *mac) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)dev->d_private; + + /* Add the MAC address to the hardware multicast routing table */ + + return OK; +} +#endif + +/**************************************************************************** + * Name: bcmf_rmmac + * + * Description: + * NuttX Callback: Remove the specified MAC address from the hardware multicast + * address filtering + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * mac - The MAC address to be removed + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +#ifdef CONFIG_NET_IGMP +static int bcmf_rmmac(FAR struct net_driver_s *dev, FAR const uint8_t *mac) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)dev->d_private; + + /* Add the MAC address to the hardware multicast routing table */ + + return OK; +} +#endif + +/**************************************************************************** + * Name: bcmf_ipv6multicast + * + * Description: + * Configure the IPv6 multicast MAC address. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +#ifdef CONFIG_NET_ICMPv6 +static void bcmf_ipv6multicast(FAR struct bcmf_driver_s *priv) +{ + FAR struct net_driver_s *dev; + uint16_t tmp16; + uint8_t mac[6]; + + /* For ICMPv6, we need to add the IPv6 multicast address + * + * For IPv6 multicast addresses, the Ethernet MAC is derived by + * the four low-order octets OR'ed with the MAC 33:33:00:00:00:00, + * so for example the IPv6 address FF02:DEAD:BEEF::1:3 would map + * to the Ethernet MAC address 33:33:00:01:00:03. + * + * NOTES: This appears correct for the ICMPv6 Router Solicitation + * Message, but the ICMPv6 Neighbor Solicitation message seems to + * use 33:33:ff:01:00:03. + */ + + mac[0] = 0x33; + mac[1] = 0x33; + + dev = &priv->dev; + tmp16 = dev->d_ipv6addr[6]; + mac[2] = 0xff; + mac[3] = tmp16 >> 8; + + tmp16 = dev->d_ipv6addr[7]; + mac[4] = tmp16 & 0xff; + mac[5] = tmp16 >> 8; + + ninfo("IPv6 Multicast: %02x:%02x:%02x:%02x:%02x:%02x\n", + mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); + + (void)bcmf_addmac(dev, mac); + +#ifdef CONFIG_NET_ICMPv6_AUTOCONF + /* Add the IPv6 all link-local nodes Ethernet address. This is the + * address that we expect to receive ICMPv6 Router Advertisement + * packets. + */ + + (void)bcmf_addmac(dev, g_ipv6_ethallnodes.ether_addr_octet); + +#endif /* CONFIG_NET_ICMPv6_AUTOCONF */ + +#ifdef CONFIG_NET_ICMPv6_ROUTER + /* Add the IPv6 all link-local routers Ethernet address. This is the + * address that we expect to receive ICMPv6 Router Solicitation + * packets. + */ + + (void)bcmf_addmac(dev, g_ipv6_ethallrouters.ether_addr_octet); + +#endif /* CONFIG_NET_ICMPv6_ROUTER */ +} +#endif /* CONFIG_NET_ICMPv6 */ + +/**************************************************************************** + * Name: bcmf_ioctl + * + * Description: + * Handle network IOCTL commands directed to this device. + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * cmd - The IOCTL command + * arg - The argument for the IOCTL command + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +#ifdef CONFIG_NETDEV_IOCTL +static int bcmf_ioctl(FAR struct net_driver_s *dev, int cmd, + unsigned long arg) +{ + FAR struct bcmf_driver_s *priv = (FAR struct bcmf_driver_s *)dev->d_private; + int ret; + + /* Decode and dispatch the driver-specific IOCTL command */ + + switch (cmd) + { + /* Add cases here to support the IOCTL commands */ + + default: + nerr("ERROR: Unrecognized IOCTL command: %d\n", command); + return -ENOTTY; /* Special return value for this case */ + } + + return OK; +} +#endif + +/**************************************************************************** + * Public Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: bcmf_initialize + * + * Description: + * Initialize the Broadcom 43362 controller and driver + * + * Parameters: + * intf - In the case where there are multiple EMACs, this value + * identifies which EMAC is to be initialized. + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +int bcmf_initialize(int intf) +{ + FAR struct bcmf_driver_s *priv; + + /* Get the interface structure associated with this interface number. */ + + DEBUGASSERT(intf < CONFIG_IEEE80211_BROADCOM_NINTERFACES); + priv = &g_bcmf_interface[intf]; + + /* Attach the IRQ to the driver */ +#warning Missing logic + + /* Initialize the driver structure */ + + memset(priv, 0, sizeof(struct bcmf_driver_s)); + priv->bc_dev.d_buf = g_pktbuf; /* Single packet buffer */ + priv->bc_dev.d_ifup = bcmf_ifup; /* I/F up (new IP address) callback */ + priv->bc_dev.d_ifdown = bcmf_ifdown; /* I/F down callback */ + priv->bc_dev.d_txavail = bcmf_txavail; /* New TX data callback */ +#ifdef CONFIG_NET_IGMP + priv->bc_dev.d_addmac = bcmf_addmac; /* Add multicast MAC address */ + priv->bc_dev.d_rmmac = bcmf_rmmac; /* Remove multicast MAC address */ +#endif +#ifdef CONFIG_NETDEV_IOCTL + priv->bc_dev.d_ioctl = bcmf_ioctl; /* Handle network IOCTL commands */ +#endif + priv->bc_dev.d_private = (FAR void *)g_bcmf_interface; /* Used to recover private state from dev */ + + /* Create a watchdog for timing polling for and timing of transmisstions */ + + priv->bc_txpoll = wd_create(); /* Create periodic poll timer */ + priv->bc_txtimeout = wd_create(); /* Create TX timeout timer */ + + DEBUGASSERT(priv->bc_txpoll != NULL && priv->bc_txtimeout != NULL); + + /* Put the interface in the down state. This usually amounts to resetting + * the device and/or calling bcmf_ifdown(). + */ + + /* Read the MAC address from the hardware into priv->bc_dev.d_mac.ether.ether_addr_octet */ + + /* Register the device with the OS so that socket IOCTLs can be performed */ + + (void)netdev_register(&priv->bc_dev, NET_LL_ETHERNET); + return OK; +} + +#endif /* CONFIG_NET && CONFIG_IEEE80211_BROADCOM_FULLMAC */