Add logic to initialize clocks

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@1108 42af7a65-404d-4744-a932-0658087f49c3

arch/arm/src/str71x/Make.defs

@@ -48,7 +48,7 @@ CMN_CSRCS	+= up_schedulesigaction.c up_sigdeliver.c
 endif
 
 CHIP_ASRCS	= str71x_lowputc.S
-CHIP_CSRCS	= str71x_decodeirq.c str71x_irq.c str71x_timerisr.c \
+CHIP_CSRCS	= str71x_prccu.c str71x_decodeirq.c str71x_irq.c str71x_timerisr.c \
 		  str71x_serial.c
 
 ifeq ($(CONFIG_USBDEV),y)

arch/arm/src/str71x/str71x_head.S

@@ -81,6 +81,23 @@
 #  endif
 #endif
 
+/*****************************************************************************
+ * External references
+ *****************************************************************************/
+
+	.globl	str71x_prccuinit	/* Clock initialization */
+	.globl	up_lowsetup		/* Early initialization of UART */
+#ifdef CONFIG_USE_EARLYSERIALINIT
+	.globl	up_earlyserialinit	/* Early initialization of serial driver */
+#endif
+#ifdef CONFIG_ARCH_LEDS
+	.globl	up_ledinit		/* Boot LED setup */
+#endif
+#ifdef CONFIG_DEBUG
+	.globl	up_lowputc		/* Low-level debug output */
+#endif
+	.globl	os_start		/* NuttX entry point */
+
 /*****************************************************************************
  * Macros
  *****************************************************************************/
@@ -368,47 +385,10 @@ eicloop:
 	ldr	\value, =STR71X_APB1_APB1ALL
 	strh	\value, [\base1, #STR71X_APB_CKDIS_OFFSET]
 
-	/* Disable all(or most) APB1 peripherals */
+	/* Disable all(or most) APB2 peripherals */
-#if 1 /* See below */
 	ldr	\value, =(STR71X_APB2_APB2ALL & ~STR71X_APB2_EIC)
-#else
-	ldr	\value, =STR71X_APB2_APB2ALL
-#endif
 	strh	\value, [\base2, #STR71X_APB_CKDIS_OFFSET]
 
-	/* Reset and enable peripherals */
-#if 0
-	/* Hold all APB1 and APB2 peripherals under reset */
-
-	ldr	\value, =STR71X_APB1_APB1ALL
-	strh	\value, [\base1, #STR71X_APB_SWRES_OFFSET]
-	ldr	\value, =STR71X_APB2_APB2ALL
-	strh	\value, [\base2, #STR71X_APB_SWRES_OFFSET]
-
-	/* Wait that the selected macrocells exit from reset */
-
-	mov	\value, #10 
-loop1:	subs	\value, \value, #1
-	bne	loop1
-
-	/* Release APB1 and APB2 peripherals from reset */
-
-	mov	\value, #0
-	strh	\value, [\base1, #STR71X_APB_SWRES_OFFSET]
-	strh	\value, [\base2, #STR71X_APB_SWRES_OFFSET]
-
-	/* Enable clocking for all APB1 and APB2 peripherals */
-
-	strh	\value, [\base1, #STR71X_APB_CKDIS_OFFSET]
-	strh	\value, [\base2, #STR71X_APB_CKDIS_OFFSET];
-
-	/* Wait that the selected macrocells exit from reset */
-
-	mov	\value, #10
-loop2:	subs	\value, \value, #1
-	bne	loop2
-#endif
-
 	/* Allow EMI and USB */
 
 	ldr	\base1, =STR71X_RCCU_BASE
@@ -543,13 +523,6 @@ __flashstart:
 
 	remap	r0, r1
 
-	/* Configure the uart so that we can get debug output as soon
-	 * as possible.  Modifies r0, r1, r2, and r14.
-	 */
-
-        bl	up_lowsetup
-	showprogress 'A'
-
 	/* Setup system stack (and get the BSS range) */
 
 	adr	r0, LC0
@@ -562,8 +535,6 @@ __flashstart:
 	strcc	r0, [r4], #4
 	bcc	1b
 
-	showprogress 'B'
-
 	/* Copy system .data sections to new home in RAM. */
 
 #ifdef CONFIG_BOOT_FROM_FLASH
@@ -577,6 +548,17 @@ __flashstart:
 	blt	1b
 
 #endif
+	/* Initialize clocking */
+
+	bl	str71x_prccuinit
+
+	/* Configure the uart so that we can get debug output as soon
+	 * as possible.  Modifies r0, r1, r2, and r14.
+	 */
+
+        bl	up_lowsetup
+	showprogress 'A'
+
 	/* Perform early serial initialization */
 
 	mov	fp, #0
@@ -584,10 +566,11 @@ __flashstart:
 	bl	up_earlyserialinit
 #endif
 
-	showprogress 'C'
+	showprogress 'B'
 
 	/* Call C++ constructors */
 
+#ifdef CONFIG_CPLUSPLUS
 	ldr 	r0, =__ctors_start__
 	ldr 	r1, =__ctors_end__
 ctor_loop:
@@ -601,7 +584,8 @@ ctor_loop:
 	b 	ctor_loop
 ctor_end:
 
-	showprogress 'D'
+	showprogress 'C'
+#endif
 	showprogress '\n'
 
 	/* Initialize onboard LEDs */
@@ -615,7 +599,8 @@ ctor_end:
 	b	os_start
 
 	/* Call destructors  -- never get here */
-#if 0
+
+#if 0 /* CONFIG_CPLUSPLUS */
 	ldr	r0, =__dtors_start__
 	ldr	r1, =__dtors_end__
 dtor_loop:

arch/arm/src/str71x/str71x_pcu.h

@@ -68,6 +68,27 @@
 
 /* Register bit settings ************************************************************/
 
+/* PCU MDIVR register bit definitions */
+
+#define STR71X_PCUMDIVR_FACTMASK    (0x0003) /* Bits 0-1: Division factor for main system clock */
+#define STR71X_PCUMDIVR_DIV1        (0x0000) /*   MCLK = RCLK */
+#define STR71X_PCUMDIVR_DIV2        (0x0001) /*   MCLK = RCLK / 2 */
+#define STR71X_PCUMDIVR_DIV4        (0x0002) /*   MCLK = RCLK / 4 */
+#define STR71X_PCUMDIVR_DIV8        (0x0003) /*   MCLK = RCLK / 8 */
+
+/* PCU PDIVR register bit definitions */
+
+#define STR71X_PCUPDIVR_FACT1MASK   (0x0003) /* Bits 0-1: Division factor for APB1 peripherals */
+#define STR71X_PCUPDIVR_APB1DIV1    (0x0000) /*   PCLK1 = RCLK */
+#define STR71X_PCUPDIVR_APB1DIV2    (0x0001) /*   PCLK1 = RCLK / 2 */
+#define STR71X_PCUPDIVR_APB1DIV4    (0x0002) /*   PCLK1 = RCLK / 4 */
+#define STR71X_PCUPDIVR_APB1DIV8    (0x0003) /*   PCLK1 = RCLK / 8 */
+#define STR71X_PCUPDIVR_FACT1MASK   (0x0300) /* Bits 8-9: Division factor for APB2 peripherals */
+#define STR71X_PCUPDIVR_APB2DIV1    (0x0000) /*   PCLK2 = RCLK */
+#define STR71X_PCUPDIVR_APB2DIV2    (0x0100) /*   PCLK2 = RCLK / 2 */
+#define STR71X_PCUPDIVR_APB2DIV4    (0x0200) /*   PCLK2 = RCLK / 4 */
+#define STR71X_PCUPDIVR_APB2DIV8    (0x0300) /*   PCLK2 = RCLK / 8 */
+
 /* PCU RSTR register bit definitions */
 
 #define STR71X_PCURSTR_EMIRESET     (0x0004) /* Bit 2: EMI reset */
@@ -88,7 +109,7 @@
 #define STR71X_PCUPPL2CR_MUL12      (0x0010) /*   CLK2 * 12 */
 #define STR71X_PCUPPL2CR_MUL28      (0x0020) /*   CLK2 * 28 */
 #define STR71X_PCUPPL2CR_MUL16      (0x0030) /*   CLK2 * 16 */
-#define STR71X_PCUPPL2CR_FRRRNG     (0x0040) /* Bit 6: PLL2 frequency range selection */
+#define STR71X_PCUPPL2CR_FRQRNG     (0x0040) /* Bit 6: PLL2 frequency range selection */
 #define STR71X_PCUPPL2CR_PLLEN      (0x0080) /* Bit 7: PLL2 enable */
 #define STR71X_PCUPPL2CR_USBEN      (0x0100) /* Bit 8: Enable PLL clock to USB */
 #define STR71X_PCUPPL2CR_IRQMASK    (0x0200) /* Bit 9: Enable interrupt request CPU on lock transition */

arch/arm/src/str71x/str71x_prccu.c

@@ -0,0 +1,342 @@
+/********************************************************************************
+ * arch/arm/src/str71x/str71x_prccu.c
+ *
+ *   Copyright (C) 2008 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <spudmonkey@racsa.co.cr>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ********************************************************************************/
+
+/********************************************************************************
+ * Included Files
+ ********************************************************************************/
+
+#include <nuttx/config.h>
+#include <sys/types.h>
+
+#include <assert.h>
+#include <debug.h>
+
+#include <nuttx/irq.h>
+#include <nuttx/arch.h>
+
+#include "chip.h"
+
+/********************************************************************************
+ * Definitions
+ ********************************************************************************/
+
+/* Input frequency (CLK2) is either the main oscillator or the main oscillator
+ * divided by 2.
+ */
+
+#ifdef STR71X_PLL1_DIV2
+#  define STR71X_PLL1_CLK2     (STR71X_RCCU_MAIN_OSC/2)
+#else
+#  define STR71X_RCCU_MAIN_OSC STR71X_RCCU_MAIN_OSC
+#endif
+
+/* Select set of peripherals to be enabled */
+
+/* APB1 periperals */
+
+#ifndef CONFIG_STR71X_I2C0
+#  define APB1EN_I2C0 STR71X_APB1_I2C0
+#else
+#  define APB1EN_I2C0 (0)
+#endif
+
+#ifndef CONFIG_STR71X_I2C1
+#  define APB1EN_I2C1 STR71X_APB1_I2C1
+#else
+#  define APB1EN_I2C1 (0)
+#endif
+
+#ifndef CONFIG_STR71X_UART0
+#  define APB1EN_UART0 STR71X_APB1_UART0
+#else
+#  define APB1EN_UART0 (0)
+#endif
+
+#ifndef CONFIG_STR71X_UART1
+#  define APB1EN_UART1 STR71X_APB1_UART1
+#else
+#  define APB1EN_UART1 (0)
+#endif
+
+#ifndef CONFIG_STR71X_UART2
+#  define APB1EN_UART2 STR71X_APB1_UART2
+#else
+#  define APB1EN_UART2 (0)
+#endif
+
+#ifndef CONFIG_STR71X_UART3
+#  define APB1EN_UART3 STR71X_APB1_UART3
+#else
+#  define APB1EN_UART3 (0)
+#endif
+
+#ifndef CONFIG_STR71X_USB
+#  define APB1EN_USB STR71X_APB1_USB
+#else
+#  define APB1EN_USB (0)
+#endif
+
+#ifndef CONFIG_STR71X_CAN
+#  define APB1EN_CAN STR71X_APB1_CAN
+#else
+#  define APB1EN_CAN (0)
+#endif
+
+#ifndef CONFIG_STR71X_BSPI0
+#  define APB1EN_BSPI0 STR71X_APB1_BSPI0
+#else
+#  define APB1EN_BSPI0 (0)
+#endif
+
+#ifndef CONFIG_STR71X_BSPI1
+#  define APB1EN_BSPI1 STR71X_APB1_BSPI1
+#else
+#  define APB1EN_BSPI1 (0)
+#endif
+
+#ifndef CONFIG_STR71X_HDLC
+#  define APB1EN_HDLC STR71X_APB1_HDLC
+#else
+#  define APB1EN_HDLC (0)
+#endif
+
+#define APB1EN_ALL (APB1EN_I2C0|APB1EN_I2C1|APB1EN_UART0|APB1EN_UART1|\
+                    APB1EN_UART2|APB1EN_UART3|APB1EN_USB|APB1EN_CAN|\
+                    APB1EN_BSPI0|APB1EN_BSPI1|APB1EN_HDLC)
+
+/* APB2 Peripherals */
+
+#ifndef CONFIG_STR71X_XTI
+#  define APB2EN_XTI STR71X_APB2_XTI
+#else
+#  define APB2EN_XTI (0)
+#endif
+
+#ifndef CONFIG_STR71X_GPIO0
+#  define APB2EN_GPIO0 STR71X_APB2_GPIO0
+#else
+#  define APB2EN_GPIO0 (0)
+#endif
+
+#ifndef CONFIG_STR71X_GPIO1
+#  define APB2EN_GPIO1 STR71X_APB2_GPIO1
+#else
+#  define APB2EN_GPIO1 (0)
+#endif
+
+#ifndef CONFIG_STR71X_GPIO2
+#  define APB2EN_GPIO2 STR71X_APB2_GPIO2
+#else
+#  define APB2EN_GPIO2 (0)
+#endif
+
+#ifndef CONFIG_STR71X_ADC12
+#  define APB2EN_ADC12 STR71X_APB2_ADC12
+#else
+#  define APB2EN_ADC12 (0)
+#endif
+
+#ifndef CONFIG_STR71X_CKOUT
+#  define APB2EN_CKOUT STR71X_APB2_CKOUT
+#else
+#  define APB2EN_CKOUT (0)
+#endif
+
+#define APB2EN_TIM0 (0) /* System timer -- always enabled */
+
+#ifndef CONFIG_STR71X_TIM1
+#  define APB2EN_TIM1 STR71X_APB2_TIM1
+#else
+#  define APB2EN_TIM1 (0)
+#endif
+
+#ifndef CONFIG_STR71X_TIM2
+#  define APB2EN_TIM2 STR71X_APB2_TIM2
+#else
+#  define APB2EN_TIM2 (0)
+#endif
+
+#ifndef CONFIG_STR71X_TIM3
+#  define APB2EN_TIM3 STR71X_APB2_TIM3
+#else
+#  define APB2EN_TIM3 (0)
+#endif
+
+#ifndef CONFIG_STR71X_RTC
+#  define APB2EN_RTC STR71X_APB2_RTC
+#else
+#  define APB2EN_RTC (0)
+#endif
+
+#define APB2EN_EIC (0) /* Interrupt controller always enabled */
+
+#define APB2EN_ALL (APB2EN_XTI|APB2EN_GPIO0|APB2EN_GPIO1|APB2EN_GPIO2|\
+                    APB2EN_ADC12|APB2EN_CKOUT|APB2EN_TIM0|APB2EN_TIM1|\
+                    APB2EN_TIM2|APB2EN_TIM3|APB2EN_RTC|APB2EN_EIC)
+
+/********************************************************************************
+ * Private Types
+ ********************************************************************************/
+
+/********************************************************************************
+ * Public Data
+ ********************************************************************************/
+
+/********************************************************************************
+ * Private Data
+ ********************************************************************************/
+
+/********************************************************************************
+ * Private Functions
+ ********************************************************************************/
+
+/********************************************************************************
+ * Public Funstions
+ ********************************************************************************/
+
+/********************************************************************************
+ * Name: str71x_prccuinit
+ *
+ * Description:
+ *   Initialize the PCU/RCCU based on the NuttX configuration and the board-specific
+ *   settings in board.h
+ *
+ ********************************************************************************/
+
+void str71x_prccuinit(void)
+{
+  uint32 reg32;
+  uint16 reg16;
+
+ /* Divide RCLK to obtain PCLK1 & 2 clock for the APB1 & 2 peripherals.  The divider
+  * values are provided in board.h
+  */
+
+  reg16  = getreg16(STR71X_PCU_PDIVR);
+  reg16 &= ~(STR71X_PCUPDIVR_FACT1MASK|STR71X_PCUPDIVR_FACT2MASK);
+  reg16 |= (STR71X_APB1_DIV|STR71X_APB2_DIV
+  putreg16(reg16, STR71X_PCU_PDIVR);
+
+  /* Configure the main system clock (MCLK) divider with value from board.h */
+
+  reg16 = getreg16(STR71X_PCU_MDIVR);
+  reg16 &= ~STR71X_PCUMDIVR_FACTMASK;
+  reg16 |= STR71X_MCLK_DIV
+  purreg16(reg16 , STR71X_PCU_MDIVR);
+
+  /* Turn off the PLL1 by setting bits DX[2:0] */
+
+  putreg32(STR71X_RCCUPLL1CR_CLK2, STR71X_RCCU_PLL1CR);
+
+  /* Configure the PLL1CR register using the provided multiplier and
+   * divider.  The FREF_RANGE bit is also set if the input frequency
+   * (CLK2) is greater than 3MHz.
+   */
+
+#if STR71X_PLL1_CLK2 > 3000000
+  putreg32(STR71X_PLL1OUT_MUL|STR71X_PLL1OUT_DIV, STR71X_RCCU_PLL1CR);
+#else
+  putreg32(STR71X_PLL1OUT_MUL|STR71X_PLL1OUT_DIV|STR71X_RCCUPLL1CR_FREFRANGE, STR71X_RCCU_PLL1CR);
+#endif
+
+  /* Wait for the PLL to lock */
+
+  while (getreg16(STR71X_RCCU_CFR) & STR71X_RCCUCFR_LOCK) == 0);
+
+  /* Set the CK2_16 Bit in the CFR to use CLK2/PLL1OUT as CLK3 */
+
+  reg32 = getreg32(STR71X_RCCU_CFR);
+  putreg32(reg32 | STR71X_RCCUCFR_CK216, STR71X_RCCU_CFR);
+
+  /* Wait for the PLL to lock */
+
+  while (getreg16(STR71X_RCCU_CFR) & STR71X_RCCUCFR_LOCK) == 0);
+
+  /* Select CLK3 (vs the alternative source) for RCLK in the clock
+   * control register (CCR)
+   */
+
+  reg16 = getreg16(STR71X_RCCU_CCR);
+  reg16 &= ~STR71X_RCCUCCR_CKAFSEL
+  putreg16(reg16, STR71X_RCCU_CCR);
+
+  /* Select PLL1OUT as the CLK3 */
+
+  reg32 = getreg32(STR71X_RCCU_CFR);
+  putreg32(reg32 | STR71X_RCCUCFR_CSUCKSEL, STR71X_RCCU_CFR);
+
+  /* Enable clocking on selected periperals */
+
+  putreg32(APB1EN_ALL, STR71X_APB1_CKDIS);
+  putreg32(APB2EN_ALL, STR71X_APB2_CKDIS);
+
+  /* Configure PLL2 */
+
+#if defined(CONFIG_STR71X_HDLC) || (defined(CONFIG_STR71X_USB) && defined(STR71X_USBIN_PLL2))
+  reg16  = getreg16(STR71X_PCU_PLL2CR);
+  reg16 &= ~(STR71X_PCUPPL2CR_MXMASK|STR71X_PCUPPL2CR_DXMASK);
+  reg16 |= (STR71X_PLL2OUT_MUL|STR71X_PLL2OUT_DIV);
+
+  /* Set the PLL2 FRQRNG bit according to the PLL2 input frequency */
+
+#if STR71X_PCU_HCLK_OSC < 3000000
+  reg16 &= ~STR71X_PCUPPL2CR_FRQRNG;
+#else
+  reg16 |= STR71X_PCUPPL2CR_FRQRNG;
+#else
+  putreg16(reg16, STR71X_PCU_PLL2CR);
+
+  /* Wait for PLL2 to lock in */
+  // while (getreg16(STR71X_PCU_PLL2CR) & STR71X_PCUPPL2CR_LOCK) == 0);
+#endif
+
+  /* Select the USB clock source */
+
+#ifdef CONFIG_STR71X_USB
+  reg16 = getreg16(STR71X_PCU_PLL2CR);
+#ifdef STR71X_USBIN_PLL2
+  /* PLL2 is the clock source to the USB */
+
+  reg16 |= STR71X_PCUPPL2CR_USBEN;
+#else
+  /* USBCLK pin is the clock source to the USB */
+
+  reg16 &= ~STR71X_PCUPPL2CR_USBEN;
+#endif
+  putreg16(reg16, STR71X_PCU_PLL2CR);
+#endif
+}
+
+

configs/olimex-strp711/include/board.h

@@ -32,6 +32,35 @@
  * POSSIBILITY OF SUCH DAMAGE.
  *
  ****************************************************************************/
+/****************************************************************************
+ * Features:
+ *
+ * - MCU: STR711FR2T6 16/32 bit ARM7TDMI™ with 256K Bytes Program Flash,
+ *   64K Bytes RAM, USB 2.0, RTC, 12 bit ADC, 4x UARTs, 2x I2C,2x SPI,
+ *   5x 32bit TIMERS, 2x PWM, 2x CCR, WDT, up to 50MHz operation
+ * - Standard JTAG connector with ARM 2x10 pin layout for programming/debugging
+ *   with ARM-JTAG
+ * - USB connector
+ * - Two channel RS232 interface and drivers
+ * - SD/MMC card connector
+ * - Two buttons
+ * - Trimpot connected to ADC
+ * - Two status LEDs
+ * - Buzzer
+ * - UEXT - 10 pin extension connector for Olimex addon peripherials like MP3,
+ *   RF2.4Ghz, RFID etc. modules
+ * - 2x SPI connectors
+ * - I2C connector
+ * - On board voltage regulator 3.3V with up to 800mA current
+ * - Single power supply: 6V AC or DC required, USB port can power the board
+ * - Power supply LED
+ * - Power supply filtering capacitor
+ * - RESET circuit
+ * - RESET button
+ * - 4 Mhz crystal oscillator
+ * - 32768 Hz crystal and RTC
+ *
+ ****************************************************************************/
 
 #ifndef _CONFIGS_OLIMEX_STRP711_BOARD_H
 #define _CONFIGS_OLIMEX_STRP711_BOARD_H
@@ -43,6 +72,7 @@
 #ifndef __ASSEMBLY__
 # include <sys/types.h>
 #endif
+#include "chip.h"
 
 /****************************************************************************
  * Definitions
@@ -50,10 +80,47 @@
 
 /* Clocking *****************************************************************/
 
-/* RTC Oscillator Frequency value = 32,768 Hz */
+/* Main Oscillator Frequency = 4MHz */
+
+#define STR71X_RCCU_MAIN_OSC (4000000)
+
+/* RTC Oscillator Frequency = 32,768 Hz */
 
 #define STR71X_RCCU_RTC_OSC  (32768)
 
+/* HCLK driving PLL2 */
+
+#define STR71X_PCU_HCLK_OSC  (4000000)  /* ? */
+
+/* PLL1 Setup:
+ *
+ * PLL1 input clock:      CLK2 = Main OSC = 4MHz
+ * PLL1 output clock:     PLL1OUT = 16 * CLK2 / 2 = 32MHz
+ * PLL1 output:           CLK3 = PLL1OUT = 32MHz (hard coded selection)
+ *                        RCLK = CLK3  = 32MHz (hard coded selection)
+ * APB1 peripheral clock: PCLK1 = RCLK = 32MHz
+ * APB2 peripheral clock: PCLK2 = RCLK = 32MHz
+ * Main system clock:     MCLK  = RCLK = 32MHz
+ */
+
+#undef  STR71X_PLL1IN_DIV2                            /* Don't divide main OSC by two */
+#define STR71X_PLL1OUT_MUL   STR71X_RCCUPLL1CR_MUL16  /* PLL1OUT = 16 * CLK2 */
+#define STR71X_PLL1OUT_DIV   STR71X_RCCUPLL1CR_DIV2   /* PLL1OUT = CLK2 / 2 */
+#define STR71X_APB1_DIV      STR71X_PCUPDIVR_APB1DIV1 /* PCLK1 = RCLK */
+#define STR71X_APB2_DIV      STR71X_PCUPDIVR_APB1DIV1 /* PCLK2 = RCLK */
+#define STR71X_MCLK_DIV      STR71X_PCUMDIVR_DIV1     /* MCLK = RCLK */
+
+/* PLL2 Setup -- only needed for HDLC or USB
+ *
+ * USB input: USB clock
+ * HCLK = 4MHz?
+ * USB clock = 12 * HCLK / 1 = 48 MHz
+ */
+
+#undef  STR71X_USBIN_PLL2                             /* USB input is USB clock */
+#define STR71X_PLL2OUT_MUL   STR71X_PCUPPL2CR_MUL12   /* PLL2OUT = 12 * HCLK */
+#define STR71X_PLL2OUT_DIV   STR71X_PCUPPL2CR_DIV1    /* PLL2OUT = HCLK / 1 */
+
 /* LED definitions **********************************************************/
 
 #define LED_STARTED       0

configs/olimex-strp711/ostest/defconfig

@@ -72,18 +72,48 @@ CONFIG_ARCH_STACKDUMP=y
 #
 # STR71x specific boot/build settings
 #
+# CONFIG_STR71X_I2C0, CONFIG_STR71X_I2C1, CONFIG_STR71X_UART0, CONFIG_STR71X_UART1,
+# CONFIG_STR71X_UART2, CONFIG_STR71X_UART3, CONFIG_STR71X_USB, CONFIG_STR71X_CAN,
+# CONFIG_STR71X_BSPI0, CONFIG_STR71X_BSPI1, CONFIG_STR71X_HDLC, CONFIG_STR71X_XTI, 
+# CONFIG_STR71X_GPIO0, CONFIG_STR71X_GPIO1, CONFIG_STR71X_GPIO2, CONFIG_STR71X_ADC12, 
+# CONFIG_STR71X_CKOUT, CONFIG_STR71X_TIM1, CONFIG_STR71X_TIM2, CONFIG_STR71X_TIM3, and
+# CONFIG_STR71X_RTC
+#   Select peripherals to initialize (Timer0 and EIC are always initialized)
 # CONFIG_STR71X_BANK0, CONFIG_STR71X_BANK1, CONFIG_STR71X_BANK2, and CONFIG_STR71X_BANK3
 #   Enable initialize of external memory banks 0-3.
-# CONFIG_STR71X_BANK0_SIZE, CONFIG_STR71X_BANK1_SIZE, CONFIG_STR71X_BANK2_SIZE, and CONFIG_STR71X_BANK3_SIZE
+# CONFIG_STR71X_BANK0_SIZE, CONFIG_STR71X_BANK1_SIZE, CONFIG_STR71X_BANK2_SIZE, and
+# CONFIG_STR71X_BANK3_SIZE
 #   If a particular external memory bank is configured, then its width must be provided.
 #   8 and 16 (bits) are the only valid options.
-# CONFIG_STR71X_BANK0_WAITSTATES, CONFIG_STR71X_BANK1_WAITSTATES, CONFIG_STR71X_BANK2_WAITSTATES, and CONFIG_STR71X_BANK3_WAITSTATES
+# CONFIG_STR71X_BANK0_WAITSTATES, CONFIG_STR71X_BANK1_WAITSTATES,
+# CONFIG_STR71X_BANK2_WAITSTATES, and CONFIG_STR71X_BANK3_WAITSTATES
 #   If a particular external memory bank is configured, then the number of waistates
 #   for the bank must also be provided.  Valid options are {0, .., 15}
 # CONFIG_STR71X_BIGEXTMEM
 #   The default is to provide 20 bits of address for all external memory regions.  If
 #   any memory region is larger than 1Mb, then this option should be selected.  In this
 #   case, 24 bits of addressing will be used
+CONFIG_STR71X_I2C0=n
+CONFIG_STR71X_I2C1=n
+CONFIG_STR71X_UART0=y
+CONFIG_STR71X_UART1=y
+CONFIG_STR71X_UART2=n
+CONFIG_STR71X_UART3=n
+CONFIG_STR71X_USB=n
+CONFIG_STR71X_CAN=n
+CONFIG_STR71X_BSPI0=n
+CONFIG_STR71X_BSPI1=n
+CONFIG_STR71X_HDLC=n
+CONFIG_STR71X_XTI=n
+CONFIG_STR71X_GPIO0=y
+CONFIG_STR71X_GPIO1=n
+CONFIG_STR71X_GPIO2=n
+CONFIG_STR71X_ADC12=n
+CONFIG_STR71X_CKOUT=n
+CONFIG_STR71X_TIM1=n
+CONFIG_STR71X_TIM2=n
+CONFIG_STR71X_TIM3=n
+CONFIG_STR71X_RTC=n
 CONFIG_STR71X_BANK0=n
 CONFIG_STR71X_BANK0_SIZE=16
 CONFIG_STR71X_BANK0_WAITSTATES=0
@@ -114,18 +144,32 @@ CONFIG_STR71X_BIGEXTMEM=n
 #
 CONFIG_UART0_SERIAL_CONSOLE=y
 CONFIG_UART1_SERIAL_CONSOLE=n
+CONFIG_UART2_SERIAL_CONSOLE=n
+CONFIG_UART3_SERIAL_CONSOLE=n
 CONFIG_UART0_TXBUFSIZE=256
 CONFIG_UART1_TXBUFSIZE=256
+CONFIG_UART2_TXBUFSIZE=256
+CONFIG_UART3_TXBUFSIZE=256
 CONFIG_UART0_RXBUFSIZE=256
 CONFIG_UART1_RXBUFSIZE=256
+CONFIG_UART2_RXBUFSIZE=256
+CONFIG_UART3_RXBUFSIZE=256
 CONFIG_UART0_BAUD=38400
 CONFIG_UART1_BAUD=38400
+CONFIG_UART2_BAUD=38400
+CONFIG_UART3_BAUD=38400
 CONFIG_UART0_BITS=8
 CONFIG_UART1_BITS=8
+CONFIG_UART2_BITS=8
+CONFIG_UART3_BITS=8
 CONFIG_UART0_PARITY=0
 CONFIG_UART1_PARITY=0
+CONFIG_UART2_PARITY=0
+CONFIG_UART3_PARITY=0
 CONFIG_UART0_2STOP=0
 CONFIG_UART1_2STOP=0
+CONFIG_UART2_2STOP=0
+CONFIG_UART3_2STOP=0
 
 #
 # General build options