Rearchitecting of some MTD, partition, SMART interfaces, and FLASH drivers to: Better use the byte write capbility when available and to use smaller erase sectors for the erase sector size when available).

configs/mikroe-stm32f4/Kconfig

@@ -5,53 +5,94 @@
 
 if ARCH_BOARD_MIKROE_STM32F4
 
-config PM_BUTTONS
+config MIKROE_FLASH
-	bool "PM Button support"
+	bool "MTD driver for onboard 1M FLASH"
 	default n
-	depends on PM && ARCH_IRQBUTTONS
+    select MTD
+    select MTD_M25P
+    select MTD_SMART
+    select FS_SMARTFS
+    select STM32_SPI3
+    select MTD_BYTE_WRITE
 	---help---
-		Enable PM button EXTI interrupts to support PM testing
+		Configures an MTD device for use with the onboard flash
 
-config PM_BUTTON_ACTIVITY
+config MIKROE_FLASH_MINOR
-	int "Button PM activity weight"
+	int "Minor number for the FLASH /dev/smart entry"
-	default 10
+	default 0
-	depends on PM_BUTTONS
+    depends on MIKROE_FLASH
 	---help---
-		The activity weight to report to the power management subsystem when a button is pressed.
+		Sets the minor number for the FLASH MTD /dev entry
+
+config MIKROE_FLASH_PART
+	bool "Enable partition support on FLASH"
+	default n
+    depends on MIKROE_FLASH
+	---help---
+		Enables creation of partitions on the FLASH
+
+config MIKROE_FLASH_PART_LIST
+	string "Flash partition size list"
+    default "256,768"
+    depends on MIKROE_FLASH_PART
+	---help---
+		Comma separated list of partition sizes in KB
+
+config MIKROE_RAMMTD
+	bool "MTD driver for SMARTFS RAM disk"
+	default n
+    select MTD
+    select RAMMTD
+	---help---
+		Configures an MTD based RAM device for use with SMARTFS.
+
+config MIKROE_RAMMTD_MINOR
+	int "Minor number for RAM /dev/smart entry"
+	default 1
+    depends on MIKROE_RAMMTD
+	---help---
+		Sets the minor number for the RAM MTD /dev entry
+
+config MIKROE_RAMMTD_SIZE
+	int "Size in KB of the RAM device to create"
+	default 32
+    depends on MIKROE_RAMMTD
+	---help---
+		Sets the size of static RAM allocation for the SMART RAM device
 
 config PM_ALARM_SEC
 	int "PM_STANDBY delay (seconds)"
 	default 15
 	depends on PM && RTC_ALARM
-	--help---
+	---help---
 		Number of seconds to wait in PM_STANDBY before going to PM_STANDBY mode.
 
 config PM_ALARM_NSEC
 	int "PM_STANDBY delay (nanoseconds)"
 	default 0
 	depends on PM && RTC_ALARM
-	--help---
+	---help---
 		Number of additional nanoseconds to wait in PM_STANDBY before going to PM_STANDBY mode.
 
 config PM_SLEEP_WAKEUP
 	bool "PM_SLEEP wake-up alarm"
 	default n
 	depends on PM && RTC_ALARM
-	--help---
+	---help---
 		Wake-up of PM_SLEEP mode after a delay and resume normal operation.
 
 config PM_SLEEP_WAKEUP_SEC
 	int "PM_SLEEP delay (seconds)"
 	default 10
 	depends on PM && RTC_ALARM
-	--help---
+	---help---
 		Number of seconds to wait in PM_SLEEP before going to PM_STANDBY mode.
 
 config PM_SLEEP_WAKEUP_NSEC
 	int "PM_SLEEP delay (nanoseconds)"
 	default 0
 	depends on PM && RTC_ALARM
-	--help---
+	---help---
 		Number of additional nanoseconds to wait in PM_SLEEP before going to PM_STANDBY mode.
 
 endif

configs/mikroe-stm32f4/README.txt

@@ -2,7 +2,20 @@ README
 ======
 
 This README discusses issues unique to NuttX configurations for the
-MikroElektronika Mikromedia for STM32F4 development board.
+MikroElektronika Mikromedia for STM32F4 development board.  This is
+another board support by NuttX that uses the same STM32F407VGT6 MCU
+as does the STM32F4-Discovery board. This board, however, has very
+different on-board peripherals than does the STM32F4-Discovery:
+
+  - TFT display with touch panel,
+  - VS1053 stereo audio codec with headphone jack,
+  - SD card slot,
+  - Serial FLASH memory,
+  - USB OTG FS with micro-AB connector, and
+  - Battery connect and batter charger circuit.
+
+See the http://www.mikroe.com/mikromedia/stm32-m4/ for more information
+about this board.
 
 Contents
 ========

configs/mikroe-stm32f4/src/up_nsh.c

@@ -128,9 +128,14 @@
 #    define CONFIG_EXAMPLES_SMART_NEBLOCKS (22)
 #  endif
 
-#  undef CONFIG_EXAMPLES_SMART_BUFSIZE
+#ifdef CONFIG_MIKROE_RAMMTD
-#  define CONFIG_EXAMPLES_SMART_BUFSIZE \
+#  ifndef CONFIG_MIKROE_RAMMTD_MINOR
-  (CONFIG_RAMMTD_ERASESIZE * CONFIG_EXAMPLES_SMART_NEBLOCKS)
+#    define CONFIG_MIKROE_RAMMTD_MINOR    1
+#  endif
+#  ifndef CONFIG_MIKROE_RAMMTD_SIZE
+#    define CONFIG_MIKROE_RAMMTD_SIZE     32
+#  endif
+#endif
 
 /* Debug ********************************************************************/
 
@@ -151,11 +156,6 @@
 /****************************************************************************
  * Private Data
  ****************************************************************************/
-/* Pre-allocated simulated flash */
-
-#ifdef CONFIG_RAMMTD
-//static uint8_t g_simflash[CONFIG_EXAMPLES_SMART_BUFSIZE];
-#endif
 
 /****************************************************************************
  * Public Functions
@@ -197,7 +197,7 @@ int nsh_archinitialize(void)
 
   /* Now bind the SPI interface to the M25P8 SPI FLASH driver */
 
-#ifdef CONFIG_MTD
+#if defined(CONFIG_MTD) && defined(CONFIG_MIKROE_FLASH)
   message("nsh_archinitialize: Bind SPI to the SPI flash driver\n");
   mtd = m25p_initialize(spi);
   if (!mtd)
@@ -208,28 +208,78 @@ int nsh_archinitialize(void)
     {
       message("nsh_archinitialize: Successfully bound SPI port 3 to the SPI FLASH driver\n");
 
+#ifdef CONFIG_MIKROE_FLASH_PART
+      {
+        int partno;
+        int partsize;
+        int partoffset;
+        const char *partstring = CONFIG_MIKROE_FLASH_PART_LIST;
+        const char *ptr;
+        FAR struct mtd_dev_s *mtd_part;
+        char  partname[4];
+
+        /* Now create a partition on the FLASH device */
+
+        partno = 0;
+        ptr = partstring;
+        partoffset = 0;
+        while (*ptr != '\0')
+          {
+            /* Get the partition size */
+
+            partsize = atoi(ptr);
+            mtd_part = mtd_partition(mtd, partoffset, (partsize>>2)*16);
+            partoffset += (partsize >> 2) * 16;
+
             /* Now initialize a SMART Flash block device and bind it to the MTD device */
 
 #if defined(CONFIG_MTD_SMART) && defined(CONFIG_FS_SMARTFS)
-      smart_initialize(0, mtd);
+            sprintf(partname, "p%d", partno);
+            smart_initialize(CONFIG_MIKROE_FLASH_MINOR, mtd_part, partname);
 #endif
+
+            /* Update the pointer to point to the next size in the list */
+
+            while ((*ptr >= '0') && (*ptr <= '9'))
+              {
+                ptr++;
+              }
+
+            if (*ptr == ',')
+              {
+                ptr++;
+              }
+
+            /* Increment the part number */
+
+            partno++;
+          }
+      }
+#else /* CONFIG_MIKROE_FLASH_PART */
+
+        /* Configure the device with no partition support */
+
+        smart_initialize(CONFIG_MIKROE_FLASH_MINOR, mtd, NULL);
+
+#endif /* CONFIG_MIKROE_FLASH_PART */
     }
 
   /* Create a RAM MTD device if configured */
 
-#ifdef CONFIG_RAMMTD
+#if defined(CONFIG_RAMMTD) && defined(CONFIG_MIKROE_RAMMTD)
   {
-      uint8_t *start = (uint8_t *) kmalloc(CONFIG_EXAMPLES_SMART_BUFSIZE);
+      uint8_t *start = (uint8_t *) kmalloc(CONFIG_MIKROE_RAMMTD_SIZE * 1024);
-      mtd = rammtd_initialize(start, CONFIG_EXAMPLES_SMART_BUFSIZE);
+      mtd = rammtd_initialize(start, CONFIG_MIKROE_RAMMTD_SIZE * 1024);
       mtd->ioctl(mtd, MTDIOC_BULKERASE, 0);
 
       /* Now initialize a SMART Flash block device and bind it to the MTD device */
+
 #if defined(CONFIG_MTD_SMART) && defined(CONFIG_FS_SMARTFS)
-      smart_initialize(1, mtd);
+      smart_initialize(CONFIG_MIKROE_RAMMTD_MINOR, mtd, NULL);
 #endif
   }
 
-#endif /* CONFIG_RAMMTD */
+#endif /* CONFIG_RAMMTD && CONFIG_MIKROE_RAMMTD */
 
 #endif /* CONFIG_MTD */
 #endif /* CONFIG_STM32_SPI3 */

configs/mikroe-stm32f4/usbnsh/defconfig

@@ -16,7 +16,7 @@ CONFIG_HOST_LINUX=y
 #
 # Build Configuration
 #
-# CONFIG_APPS_DIR="../apps"
+CONFIG_APPS_DIR="../apps"
 # CONFIG_BUILD_2PASS is not set
 
 #
@@ -38,27 +38,8 @@ CONFIG_RAW_BINARY=y
 #
 # Debug Options
 #
-CONFIG_DEBUG=y
+# CONFIG_DEBUG is not set
-# CONFIG_DEBUG_VERBOSE is not set
+# CONFIG_DEBUG_SYMBOLS is not set
-
-#
-# Subsystem Debug Options
-#
-# CONFIG_DEBUG_MM is not set
-# CONFIG_DEBUG_SCHED is not set
-# CONFIG_DEBUG_USB is not set
-CONFIG_DEBUG_FS=y
-# CONFIG_DEBUG_LIB is not set
-# CONFIG_DEBUG_BINFMT is not set
-# CONFIG_DEBUG_GRAPHICS is not set
-
-#
-# Driver Debug Options
-#
-# CONFIG_DEBUG_ANALOG is not set
-# CONFIG_DEBUG_SPI is not set
-# CONFIG_DEBUG_GPIO is not set
-CONFIG_DEBUG_SYMBOLS=y
 
 #
 # System Type
@@ -104,7 +85,6 @@ CONFIG_ARCH_HAVE_CMNVECTOR=y
 # CONFIG_ARCH_FPU is not set
 CONFIG_ARCH_HAVE_MPU=y
 # CONFIG_ARMV7M_MPU is not set
-# CONFIG_DEBUG_HARDFAULT is not set
 
 #
 # ARMV7M Configuration Options
@@ -310,6 +290,13 @@ CONFIG_NSH_MMCSDSPIPORTNO=0
 #
 # Board-Specific Options
 #
+CONFIG_MIKROE_FLASH=y
+CONFIG_MIKROE_FLASH_MINOR=0
+CONFIG_MIKROE_FLASH_PART=y
+CONFIG_MIKROE_FLASH_PART_LIST="256,768"
+CONFIG_MIKROE_RAMMTD=y
+CONFIG_MIKROE_RAMMTD_MINOR=1
+CONFIG_MIKROE_RAMMTD_SIZE=32
 
 #
 # RTOS Features
@@ -408,21 +395,27 @@ CONFIG_MMCSD_SPI=y
 CONFIG_MMCSD_SPICLOCK=20000000
 # CONFIG_MMCSD_SDIO is not set
 CONFIG_MTD=y
-# CONFIG_MTD_PARTITION is not set
+
+#
+# MTD Configuration
+#
+CONFIG_MTD_PARTITION=y
+CONFIG_MTD_BYTE_WRITE=y
+
+#
+# MTD Device Drivers
+#
 CONFIG_RAMMTD=y
 CONFIG_RAMMTD_BLOCKSIZE=512
 CONFIG_RAMMTD_ERASESIZE=4096
 CONFIG_RAMMTD_ERASESTATE=0xff
 # CONFIG_RAMMTD_FLASHSIM is not set
-CONFIG_RAMMTD_SMART=y
 # CONFIG_MTD_AT24XX is not set
 # CONFIG_MTD_AT45DB is not set
 CONFIG_MTD_M25P=y
 CONFIG_M25P_SPIMODE=0
 CONFIG_M25P_MANUFACTURER=0x1C
 CONFIG_M25P_MEMORY_TYPE=0x31
-CONFIG_M25P_SUBSECTOR_ERASE=y
-CONFIG_M25P_BYTEWRITE=y
 CONFIG_MTD_SMART=y
 CONFIG_MTD_SMART_SECTOR_SIZE=512
 # CONFIG_MTD_RAMTRON is not set
@@ -441,7 +434,6 @@ CONFIG_SERIAL_REMOVABLE=y
 CONFIG_ARCH_HAVE_USART2=y
 CONFIG_MCU_SERIAL=y
 CONFIG_STANDARD_SERIAL=y
-# CONFIG_SERIAL_TIOCSERGSTRUCT is not set
 # CONFIG_USART2_SERIAL_CONSOLE is not set
 CONFIG_NO_SERIAL_CONSOLE=y
 
@@ -529,7 +521,7 @@ CONFIG_FS_ROMFS=y
 CONFIG_FS_SMARTFS=y
 CONFIG_SMARTFS_ERASEDSTATE=0xff
 CONFIG_SMARTFS_MAXNAMLEN=16
-CONFIG_SMARTFS_MULTI_ROOT_DIRS=y
+# CONFIG_SMARTFS_MULTI_ROOT_DIRS is not set
 # CONFIG_FS_BINFS is not set
 
 #
@@ -650,6 +642,7 @@ CONFIG_EXAMPLES_NSH=y
 # CONFIG_EXAMPLES_NX is not set
 # CONFIG_EXAMPLES_NXCONSOLE is not set
 # CONFIG_EXAMPLES_NXFFS is not set
+# CONFIG_EXAMPLES_SMART is not set
 # CONFIG_EXAMPLES_NXFLAT is not set
 # CONFIG_EXAMPLES_NXHELLO is not set
 # CONFIG_EXAMPLES_NXIMAGE is not set
@@ -664,8 +657,8 @@ CONFIG_EXAMPLES_NSH=y
 # CONFIG_EXAMPLES_ROMFS is not set
 # CONFIG_EXAMPLES_SENDMAIL is not set
 # CONFIG_EXAMPLES_SERLOOP is not set
-CONFIG_EXAMPLES_FLASH_TEST=y
+# CONFIG_EXAMPLES_FLASH_TEST is not set
-CONFIG_EXAMPLES_SMART_TEST=y
+# CONFIG_EXAMPLES_SMART_TEST is not set
 # CONFIG_EXAMPLES_TELNETD is not set
 # CONFIG_EXAMPLES_THTTPD is not set
 # CONFIG_EXAMPLES_TIFF is not set
@@ -774,23 +767,13 @@ CONFIG_NSH_LINELEN=64
 CONFIG_NSH_NESTDEPTH=3
 # CONFIG_NSH_DISABLESCRIPT is not set
 # CONFIG_NSH_DISABLEBG is not set
-CONFIG_NSH_ROMFSETC=y
+# CONFIG_NSH_ROMFSETC is not set
-# CONFIG_NSH_ROMFSRC is not set
-CONFIG_NSH_ROMFSMOUNTPT="/etc"
-CONFIG_NSH_INITSCRIPT="init.d/rcS"
-CONFIG_NSH_ROMFSDEVNO=0
-CONFIG_NSH_ROMFSSECTSIZE=64
-CONFIG_NSH_FATDEVNO=0
-CONFIG_NSH_FATSECTSIZE=512
-CONFIG_NSH_FATNSECTORS=1024
-CONFIG_NSH_FATMOUNTPT="/tmp"
 CONFIG_NSH_CONSOLE=y
 # CONFIG_NSH_USBCONSOLE is not set
 
 #
 # USB Trace Support
 #
-# CONFIG_NSH_USBDEV_TRACE is not set
 # CONFIG_NSH_CONDEV is not set
 CONFIG_NSH_ARCHINIT=y
 

configs/stm32f4discovery/README.txt

@@ -2,7 +2,20 @@ README
 ======
 
 This README discusses issues unique to NuttX configurations for the
-STMicro STM32F4Discovery development board.
+STMicro STM32F4Discovery development board featuring the STM32F407VGT6
+MCU. The STM32F407VGT6 is a 168MHz Cortex-M4 operation with 1Mbit Flash
+memory and 128kbytes. The board features:
+
+  - On-board ST-LINK/V2 for programming and debugging,
+  - LIS302DL, ST MEMS motion sensor, 3-axis digital output accelerometer,
+  - MP45DT02, ST MEMS audio sensor, omni-directional digital microphone,
+  - CS43L22, audio DAC with integrated class D speaker driver,
+  - Eight LEDs and two push-buttons,
+  - USB OTG FS with micro-AB connector, and
+  - Easy access to most MCU pins.
+
+Refer to http://www.st.com/internet/evalboard/product/252419.jsp for
+further information about this board. 
 
 Contents
 ========