configs/stm3240g-eval/nsh2 converted to use the kconfig-frontends tools

configs/stm3240g-eval/README.txt

@@ -1097,6 +1097,7 @@ Where <subdir> is one of the following:
     CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1) : Host IP address 10.0.0.1
 
     NOTES:
+
     1. This configuration uses the mconf-based configuration tool.  To
        change this configurations using that tool, you should:
 
@@ -1334,19 +1335,29 @@ Where <subdir> is one of the following:
     curious.
 
     NOTES:
-    1. See the notes for the nsh configuration.  Most also apply to the nsh2
+
+    1. This configuration uses the mconf-based configuration tool.  To
+       change this configurations using that tool, you should:
+
+       a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
+          and misc/tools/
+
+       b. Execute 'make menuconfig' in nuttx/ in order to start the
+          reconfiguration process.
+
+    2. See the notes for the nsh configuration.  Most also apply to the nsh2
        configuration.  Like the nsh configuration, this configuration can
        be modified to support a variety of additional tests.
 
-    2. RS-232 is disabled, but Telnet is still available for use as a console.
+    3. RS-232 is disabled, but Telnet is still available for use as a console.
        Since RS-232 and SDIO use the same pins (one controlled by JP22), RS232
        and SDIO cannot be used concurrently.
 
-    3. This configuration requires that jumper JP22 be set to enable SDIO
+    4. This configuration requires that jumper JP22 be set to enable SDIO
        operation.  To enable MicroSD Card, which shares same I/Os with RS-232,
        JP22 is not fitted.
 
-    4. In order to use SDIO without overruns, DMA must be used.  The STM32 F4
+    5. In order to use SDIO without overruns, DMA must be used.  The STM32 F4
        has 192Kb of SRAM in two banks:  112Kb of "system" SRAM located at
        0x2000:0000 and 64Kb of "CCM" SRAM located at 0x1000:0000. It appears
        that you cannot perform DMA from CCM SRAM.  The work around that I have now
@@ -1358,7 +1369,7 @@ Where <subdir> is one of the following:
        Then DMA works fine. The downside is, of course, is that we lose 64Kb
        of precious SRAM.
 
-    5. Another SDIO/DMA issue.  This one is probably a software bug.  This is
+    6. Another SDIO/DMA issue.  This one is probably a software bug.  This is
        the bug as stated in the TODO list:
 
        "If you use a large I/O buffer to access the file system, then the
@@ -1369,7 +1380,7 @@ Where <subdir> is one of the following:
        For this reason, CONFIG_MMCSD_MULTIBLOCK_DISABLE=y appears in the defconfig
        file.
 
-    6. Another DMA-related concern.  I see this statement in the reference
+    7. Another DMA-related concern.  I see this statement in the reference
        manual:  "The burst configuration has to be selected in order to respect
        the AHB protocol, where bursts must not cross the 1 KB address boundary
        because the minimum address space that can be allocated to a single slave

configs/stm3240g-eval/nsh/defconfig

@@ -519,11 +519,11 @@ CONFIG_NETDEVICES=y
 #
 # External Ethernet PHY Device Support
 #
-CONFIG_ETH0_PHY_NONE=y
+# CONFIG_ETH0_PHY_NONE is not set
 # CONFIG_ETH0_PHY_KS8721 is not set
 # CONFIG_ETH0_PHY_KSZ8051 is not set
 # CONFIG_ETH0_PHY_KSZ90x1 is not set
-# CONFIG_ETH0_PHY_DP83848C is not set
+CONFIG_ETH0_PHY_DP83848C=y
 # CONFIG_ETH0_PHY_LAN8720 is not set
 # CONFIG_ETH0_PHY_DM9161 is not set
 # CONFIG_PIPES is not set

configs/stm3240g-eval/nsh2/appconfig

@@ -1,89 +0,0 @@
-############################################################################
-# configs/stm3240g-eval/nsh2/appconfig
-#
-#   Copyright (C) 2012 Gregory Nutt. All rights reserved.
-#   Author: Gregory Nutt <gnutt@nuttx.org>
-#
-# Redistribution and use in source and binary forms, with or without
-# modification, are permitted provided that the following conditions
-# are met:
-#
-# 1. Redistributions of source code must retain the above copyright
-#    notice, this list of conditions and the following disclaimer.
-# 2. Redistributions in binary form must reproduce the above copyright
-#    notice, this list of conditions and the following disclaimer in
-#    the documentation and/or other materials provided with the
-#    distribution.
-# 3. Neither the name NuttX nor the names of its contributors may be
-#    used to endorse or promote products derived from this software
-#    without specific prior written permission.
-#
-# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
-# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
-# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
-# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
-# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
-# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
-# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
-# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
-# POSSIBILITY OF SUCH DAMAGE.
-#
-############################################################################
-
-# Path to example in apps/examples containing the user_start entry point
-
-CONFIGURED_APPS += examples/nsh
-
-# The NSH application library
-
-CONFIGURED_APPS += system/readline
-CONFIGURED_APPS += nshlib
-
-# Networking libraries.
-# Uncomment netutils/ftpc to include an FTP client library
-# Uncomment netutils/ftpd to include an FTP server library
-
-ifeq ($(CONFIG_NET),y)
-CONFIGURED_APPS += netutils/uiplib
-CONFIGURED_APPS += netutils/resolv
-CONFIGURED_APPS += netutils/webclient
-CONFIGURED_APPS += netutils/tftpc
-#CONFIGURED_APPS += netutils/ftpc
-#CONFIGURED_APPS += netutils/ftpd
-ifeq ($(CONFIG_NSH_TELNET),y)
-CONFIGURED_APPS += netutils/telnetd
-endif
-endif
-
-# Applications configured as an NX built-in commands
-
-ifeq ($(CONFIG_ADC),y)
-CONFIGURED_APPS += examples/adc
-endif
-
-ifeq ($(CONFIG_PWM),y)
-CONFIGURED_APPS += examples/pwm
-endif
-
-ifeq ($(CONFIG_CAN),y)
-CONFIGURED_APPS += examples/can
-endif
-
-ifeq ($(CONFIG_I2C),y)
-CONFIGURED_APPS += system/i2c
-endif
-
-ifeq ($(CONFIG_WATCHDOG),y)
-CONFIGURED_APPS += examples/watchdog
-endif
-
-# Uncomment examples/ftpc to include the FTP client example
-# Uncomment examples/ftpd to include the FTP daemon example
-
-ifeq ($(CONFIG_NET),y)
-#CONFIGURED_APPS += examples/ftpc
-#CONFIGURED_APPS += examples/ftpd
-endif