LPC-H3131 SDRAM: Fix some build issues
This commit is contained in:
Gregory Nutt
parent
e93894b53a
commit
68c964e3e2
@ -578,7 +578,79 @@ Configurations
|
||||
- Toolchain: CodeSourcery for Windows
|
||||
|
||||
NOTES:
|
||||
1. This configuration has been used to test USB host functionaly. USB
|
||||
1. Built-in applications are not supported by default. To enable NSH
|
||||
built-in applications:
|
||||
|
||||
Binary
|
||||
CONFIG_BUILTIN=y : Support built-in applications
|
||||
|
||||
Application Configuration -> NSH Library
|
||||
CONFIG_NSH_BUILTIN_APPS=y : Enable built-in applications
|
||||
|
||||
2. SDRAM support is not enabled by default. SDRAM support can be enabled
|
||||
by adding the following to your NuttX configuration file:
|
||||
|
||||
System Type->LPC31xx Peripheral Support
|
||||
CONFIG_LPC31_EXTDRAM=y : Enable external DRAM support
|
||||
CONFIG_LPC31_EXTDRAMSIZE=33554432 : 256Mbit -> 32Mbyte
|
||||
CONFIG_LPC31_SDRAM_16BIT=y : Organized 16Mbit x 16 bits wide
|
||||
|
||||
Now that you have SDRAM enabled, what are you going to do with it? One
|
||||
thing you can is add it to the heap
|
||||
|
||||
System Type->Heap Configuration
|
||||
CONFIG_LPC31_EXTDRAMHEAP=y : Add the SDRAM to the heap
|
||||
|
||||
Memory Management
|
||||
CONFIG_MM_REGIONS=2 : Two memory regions: ISRAM and SDRAM
|
||||
|
||||
Another thing you could do is to enable the RAM test built-in
|
||||
application:
|
||||
|
||||
3. You can enable the NuttX RAM test that may be used to verify the
|
||||
external SDAM. To do this, keep the SDRAM out of the heap so that
|
||||
it can be tested without crashing programs using the memory.
|
||||
|
||||
First enable built-in applications as described above, then make
|
||||
the following additional modifications to the NuttX configuration:
|
||||
|
||||
System Type->Heap Configuration
|
||||
CONFIG_LPC31_EXTDRAMHEAP=n : Don't add the SDRAM to the heap
|
||||
|
||||
Memory Management
|
||||
CONFIG_MM_REGIONS=1 : One memory regions: ISRAM
|
||||
|
||||
Then enable the RAM test built-in application:
|
||||
|
||||
Application Configuration->System NSH Add-Ons->Ram Test
|
||||
CONFIG_SYSTEM_RAMTEST=y
|
||||
|
||||
In this configuration, the SDRAM is not added to heap and so is not
|
||||
excessible to the applications. So the RAM test can be freely
|
||||
executed against the SRAM memory beginning at address 0x2000:0000
|
||||
(DDR CS):
|
||||
|
||||
nsh> ramtest -h
|
||||
Usage: ramtest [-w|h|b] <hex-address> <decimal-size>
|
||||
|
||||
Where:
|
||||
<hex-address> starting address of the test.
|
||||
<decimal-size> number of memory locations (in bytes).
|
||||
-w Sets the width of a memory location to 32-bits.
|
||||
-h Sets the width of a memory location to 16-bits (default).
|
||||
-b Sets the width of a memory location to 8-bits.
|
||||
|
||||
To test the entire external 256MB SRAM:
|
||||
|
||||
nsh> ramtest -w 30000000 33554432
|
||||
RAMTest: Marching ones: 30000000 33554432
|
||||
RAMTest: Marching zeroes: 30000000 33554432
|
||||
RAMTest: Pattern test: 30000000 33554432 55555555 aaaaaaaa
|
||||
RAMTest: Pattern test: 30000000 33554432 66666666 99999999
|
||||
RAMTest: Pattern test: 30000000 33554432 33333333 cccccccc
|
||||
RAMTest: Address-in-address test: 30000000 33554432
|
||||
|
||||
4. This configuration has been used to test USB host functionaly. USB
|
||||
host is *not* enabled by default. If you will to enable USB host
|
||||
support in the NSH configuration, please modify the NuttX
|
||||
configuration as follows:
|
||||
|
||||
@ -1,13 +1,11 @@
|
||||
/****************************************************************************
|
||||
* configs/ea3131/src/up_mem.c
|
||||
* arch/arm/src/board/up_mem.c
|
||||
* configs/olimex-lpc-h3131/src/lp31_mem.c
|
||||
*
|
||||
* Copyright (C) 2009-2010,2012 Gregory Nutt. All rights reserved.
|
||||
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* References:
|
||||
* - NXP UM10314 LPC3130/31 User manual Rev. 1.01 — 9 September 2009
|
||||
* - NXP lpc313x.cdl.drivers.zip example driver code
|
||||
* Based on the EA3131 SDRAM initialization logic with adjustments to the
|
||||
* timing parameters taken from Olimex LPC-H3131 sample code.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
@ -65,25 +63,25 @@
|
||||
* Pre-processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* The MPMC delay based on trace lengths between SDRAM and the chip and on
|
||||
* the delay strategy used for SDRAM.
|
||||
/* My LPC-H3131 is fitted with a Samsung K4S561632J-UC/L75 256Mbit DRAM.
|
||||
* The FLASH organization is 16Mbit x 16
|
||||
*/
|
||||
|
||||
/* Command, address, and data delay (DEL2) */
|
||||
|
||||
#define H3131_MPMC_DELAY (0x00 << SYSCREG_MPMC_DELAYMODES_DEL1_SHIFT) | \
|
||||
(0x20 << SYSCREG_MPMC_DELAYMODES_DEL2_SHIFT) | \
|
||||
(0x24 << SYSCREG_MPMC_DELAYMODES_DEL3_SHIFT);
|
||||
#define H3131_MPMC_DELAY ((0x00 << SYSCREG_MPMC_DELAYMODES_DEL1_SHIFT) | \
|
||||
(0x20 << SYSCREG_MPMC_DELAYMODES_DEL2_SHIFT) | \
|
||||
(0x24 << SYSCREG_MPMC_DELAYMODES_DEL3_SHIFT))
|
||||
|
||||
|
||||
/* Delay constants in nanosecondss for MT48LC32M16LF SDRAM on board */
|
||||
/* Delay constants in nanosecondss for K4S561632J-UC/L75 SDRAM on board */
|
||||
/* 90MHz SDRAM Clock */
|
||||
|
||||
#define H3131_SDRAM_TRP (20) /* ns */
|
||||
#define H3131_SDRAM_TRFC (80) /* ns */
|
||||
#define H3131_SDRAM_TRAS (48) /* ns */
|
||||
#define H3131_SDRAM_TREX (80) /* ns */
|
||||
#define H3131_SDRAM_TAPR 2
|
||||
#define H3131_SDRAM_TAPR 2 /* clocks */
|
||||
#define H3131_SDRAM_TWR (15) /* ns */
|
||||
#define H3131_SDRAM_TRC (72) /* ns */
|
||||
#define H3131_SDRAM_TRRD (2) /* clocks */
|
||||
@ -111,7 +109,7 @@
|
||||
|
||||
#endif
|
||||
|
||||
#define NS2HCLKS(ns,hclk2,mask) (_NS2HCLKS & mask)
|
||||
#define NS2HCLKS(ns,hclk2,mask) (_NS2HCLKS(ns,hclk2) & mask)
|
||||
|
||||
/****************************************************************************
|
||||
* Private Data
|
||||
@ -127,53 +125,12 @@
|
||||
* Description:
|
||||
* Configure SDRAM on the Olimex LPC-H3131 board
|
||||
*
|
||||
* Micron Initialization Sequence from their data sheet for the Micron
|
||||
* MT48LC32M16A2 32M x 16 SDRAM chip:
|
||||
*
|
||||
* "SDRAMs must be powered up and initialized in a predefined manner.
|
||||
* Operational procedures other than those specified may result in
|
||||
* undefined operation. Once power is applied to VDD and VDDQ
|
||||
* (simultaneously) and the clock is stable (stable clock is defined as
|
||||
* a signal cycling within timing constraints specified for the clock
|
||||
* pin), the SDRAM requires a 100µs delay prior to issuing any command
|
||||
* other than a COMMAND INHIBIT or NOP.
|
||||
*
|
||||
* "Starting at some point during this 100µs period and continuing at least
|
||||
* through the end of this period, COMMAND INHIBIT or NOP commands should
|
||||
* be applied. Once the 100µs delay has been satisfied with at least one
|
||||
* COMMAND INHIBIT or NOP command having been applied, a PRECHARGE command
|
||||
* should be applied. All banks must then be precharged, thereby placing
|
||||
* the device in the all banks idle state.
|
||||
*
|
||||
* "Once in the idle state, two AUTO REFRESH cycles must be performed. After
|
||||
* the AUTO REFRESH cycles are complete, the SDRAM is ready for mode
|
||||
* register programming.
|
||||
*
|
||||
* "Because the mode register will power up in an unknown state, it should
|
||||
* be loaded prior to applying any operational command."
|
||||
*
|
||||
* The JEDEC recommendation for initializing SDRAM is:
|
||||
*
|
||||
* APPLY POWER (Vdd/Vddq equally, and CLK is stable)
|
||||
* Wait 200uS
|
||||
* PRECHARGE all
|
||||
* 8 AUTO REFRESH COMMANDS
|
||||
* LOAD MODE REGISTER
|
||||
* SDRAM is ready for operation
|
||||
*
|
||||
* The Micron SDRAM parts will work fine with the JEDEC sequence, but also
|
||||
* allow for a quicker init sequence of:
|
||||
*
|
||||
* APPLY POWER (Vdd/Vddq equally, and CLK is stable)
|
||||
* Wait at least 100uS (during which time start applying and
|
||||
* continue applying NOP or COMMAND INHIBIT)
|
||||
* PRECHARGE all
|
||||
* 2 AUTO REFRESH COMMANDS (min requirement, more than 2 is also ok)
|
||||
* LOAD MODE REGISTER
|
||||
* SDRAM is ready for operation
|
||||
* My LPC-H3131 is fitted with a Samsung K4S561632J-UC/L75 256Mbit DRAM.
|
||||
* The FLASH organization is 16Mbit x 16
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
static inline void lpc31_sdraminitialize(void)
|
||||
{
|
||||
uint32_t tmp;
|
||||
uint32_t regval;
|
||||
@ -226,7 +183,7 @@
|
||||
putreg32(NS2HCLKS(H3131_SDRAM_TREX, HCLK2, MPMC_DYNTSREX_MASK),
|
||||
LPC31_MPMC_DYNTSREX);
|
||||
putreg32(H3131_SDRAM_TAPR, LPC31_MPMC_DYNTAPR);
|
||||
putreg32(((H3131_SDRAM_TDAL + _NS2HCLKS(H3131_SDRAM_TRP, HCLK2)) MPMC_DYNTDAL_MASK),
|
||||
putreg32(((H3131_SDRAM_TDAL + _NS2HCLKS(H3131_SDRAM_TRP, HCLK2)) & MPMC_DYNTDAL_MASK),
|
||||
LPC31_MPMC_DYNTDAL);
|
||||
putreg32(NS2HCLKS(H3131_SDRAM_TWR, HCLK2, MPMC_DYNTWR_MASK),
|
||||
LPC31_MPMC_DYNTWR);
|
||||
@ -273,6 +230,8 @@
|
||||
/* Recommended refresh interval for normal operation of the Micron
|
||||
* MT48LC16LFFG = 7.8125usec (128KHz rate). ((HCLK / 128000) - 1) =
|
||||
* refresh counter interval rate, (subtract one for safety margin).
|
||||
*
|
||||
* REVISIT: Is this okay for the Samsung part?
|
||||
*/
|
||||
|
||||
putreg32(NS2HCLKS(H3131_SDRAM_OPERREFRESH, HCLK, MPMC_DYNREFRESH_TIMER_MASK),
|
||||
@ -375,7 +334,7 @@ void lpc31_meminitialize(void)
|
||||
|
||||
putreg32(H3131_MPMC_DELAY, LPC31_SYSCREG_MPMC_DELAYMODES);
|
||||
|
||||
/* Configure Micron MT48LC32M16A2 SDRAM on the H3131 board */
|
||||
/* Configure Samsung K4S561632J-UC/L75 DRAM on the H3131 board */
|
||||
|
||||
lpc31_sdraminitialize();
|
||||
}
|
||||
Loading…
Reference in New Issue
Block a user