Add STM32F4Discovery configuration with the STM32F4DIS-BB base board

configs/stm32f4discovery/Kconfig

@@ -5,8 +5,15 @@
 
 if ARCH_BOARD_STM32F4_DISCOVERY
 
+config STM32F4DISBB
+	bool "STM32F4DIS-BB base board"
+	default n
+	---help---
+		Select if you are using the STM32F4DIS-BB base board with the
+		STM32F4Discovery.
+
 config PM_BUTTONS
-	bool "PM Button support"
+	bool "PM button support"
 	default n
 	depends on PM && ARCH_IRQBUTTONS
 	---help---
@@ -17,21 +24,24 @@ config PM_BUTTON_ACTIVITY
 	default 10
 	depends on PM_BUTTONS
 	---help---
-		The activity weight to report to the power management subsystem when a button is pressed.
+		The activity weight to report to the power management subsystem when
+		a button is pressed.
 
 config PM_ALARM_SEC
 	int "PM_STANDBY delay (seconds)"
 	default 15
 	depends on PM && RTC_ALARM
 	---help---
-		Number of seconds to wait in PM_STANDBY before going to PM_STANDBY mode.
+		Number of seconds to wait in PM_STANDBY before going to PM_STANDBY
+		mode.
 
 config PM_ALARM_NSEC
 	int "PM_STANDBY delay (nanoseconds)"
 	default 0
 	depends on PM && RTC_ALARM
 	---help---
-		Number of additional nanoseconds to wait in PM_STANDBY before going to PM_STANDBY mode.
+		Number of additional nanoseconds to wait in PM_STANDBY before going
+		to PM_STANDBY mode.
 
 config PM_SLEEP_WAKEUP
 	bool "PM_SLEEP wake-up alarm"
@@ -52,6 +62,7 @@ config PM_SLEEP_WAKEUP_NSEC
 	default 0
 	depends on PM && RTC_ALARM
 	---help---
-		Number of additional nanoseconds to wait in PM_SLEEP before going to PM_STANDBY mode.
+		Number of additional nanoseconds to wait in PM_SLEEP before going to
+		PM_STANDBY mode.
 
 endif

configs/stm32f4discovery/README.txt

@@ -356,9 +356,14 @@ USART6
 Default USART/UART Configuration
 --------------------------------
 
-USART2 is enabled in all configurations (see */defconfig).  RX and TX are
+USART2 is enabled in most configurations (see */defconfig).  RX and TX are
 configured on pins PA3 and PA2, respectively (see include/board.h).
 
+These pins selections, however, conflict with Ethernet pin usage on the
+STM32F4DIS-BB base board.  The STM32F4DIS-BB base board provides RS-232
+drivers and a DB9 connector for USART6.  USART6 is the preferred serial
+console for use with the STM32F4DIS-BB.
+
 Timer Inputs/Outputs
 ====================
 

configs/stm32f4discovery/include/board.h

@@ -1,8 +1,7 @@
 /************************************************************************************
  * configs/stm32f4discovery/include/board.h
- * include/arch/board/board.h
  *
- *   Copyright (C) 2012 Gregory Nutt. All rights reserved.
+ *   Copyright (C) 2012, 2014 Gregory Nutt. All rights reserved.
  *   Author: Gregory Nutt <gnutt@nuttx.org>
  *
  * Redistribution and use in source and binary forms, with or without
@@ -209,12 +208,27 @@
 /* UART2:
  *
  * The STM32F4 Discovery has no on-board serial devices, but the console is
- * brought out to PA2 (TX) and PA3 (RX) for connection to an external serial device.
+ * brought out to PA2 (TX) and PA3 (RX) for connection to an external serial
- * (See the README.txt file for other options)
+ * device. (See the README.txt file for other options)
+ *
+ * These pins selections, however, conflict with pin usage on the STM32F4DIS-BB.
  */
 
-#define GPIO_USART2_RX GPIO_USART2_RX_1
+#ifdef CONFIG_STM32F4DISBB
-#define GPIO_USART2_TX GPIO_USART2_TX_1
+#  define GPIO_USART2_RX GPIO_USART2_RX_1
+#  define GPIO_USART2_TX GPIO_USART2_TX_1
+#endif
+
+/* UART6:
+ *
+ * The STM32F4DIS-BB base board provides RS-232 drivers and a DB9 connector
+ * for USART6.  This is the preferred serial console for use with the STM32F4DIS-BB.
+ */
+
+#ifdef CONFIG_STM32F4DISBB
+#  define GPIO_USART6_RX GPIO_USART6_RX_1 
+#  define GPIO_USART6_TX GPIO_USART6_TX_1 
+#endif
 
 /* PWM
  *
@@ -238,6 +252,31 @@
 #define GPIO_TIM8_CH1IN  GPIO_TIM8_CH1IN_1
 #define GPIO_TIM8_CH2IN  GPIO_TIM8_CH2IN_1
 
+/* Ethernet *************************************************************************/
+
+
+#if defined(CONFIG_STM32F4DISBB) && defined(CONFIG_STM32_ETHMAC)
+  /* RMII interface to the LAN8720 PHY */
+
+#  ifndef CONFIG_STM32_RMII
+#    error CONFIG_STM32_RMII must be defined
+#  endif
+
+  /* Clocking is provided by an external 25Mhz XTAL */
+
+#  ifndef CONFIG_STM32_RMII_EXTCLK
+#    error CONFIG_STM32_RMII_EXTCLK must be defined
+#  endif
+
+  /* Pin disambiguation */
+
+#  define GPIO_ETH_RMII_TX_EN GPIO_ETH_RMII_TX_EN_1 
+#  define GPIO_ETH_RMII_TXD0  GPIO_ETH_RMII_TXD0_1 
+#  define GPIO_ETH_RMII_TXD1  GPIO_ETH_RMII_TXD1_1 
+#  define GPIO_ETH_PPS_OUT    GPIO_ETH_PPS_OUT_1 
+
+#endif
+
 /************************************************************************************
  * Public Data
  ************************************************************************************/
@@ -247,7 +286,8 @@
 #undef EXTERN
 #if defined(__cplusplus)
 #define EXTERN extern "C"
-extern "C" {
+extern "C"
+{
 #else
 #define EXTERN extern
 #endif
@@ -260,7 +300,7 @@ extern "C" {
  *
  * Description:
  *   All STM32 architectures must provide the following entry point.  This entry point
- *   is called early in the intitialization -- after all memory has been configured
+ *   is called early in the initialization -- after all memory has been configured
  *   and mapped but before any devices have been initialized.
  *
  ************************************************************************************/