Update3 LPC4330 README files

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4921 42af7a65-404d-4744-a932-0658087f49c3

configs/lpc4330-xplorer/README.txt

@@ -273,17 +273,50 @@ Code Red IDE
   Command Line Flash Programming
   ------------------------------
 
-  The GCC toolchain in LPCXpresso can be used from the command line.  The
-  GDB configuration details for command line use are on Code Red Wiki:
+  The underlying debugger within Red Suite/LPCXpresso is GDB.  That GDB
+  used from the command line.  The GDB configuration details for command
+  line use are on Code Red Wiki:
 
     http://support.code-red-tech.com/CodeRedWiki/UsingGDB
 
-  The driver for the LPC18xx and LPC43xx is (in my installation path):
+  and is also summarized here (see the full Wiki for additional details
+  and optins).
+
+  The Code Red Debug Driver implements the GDB "remote" protocol to allow
+  connection to debug targets.  To start a debug session using GDB, use
+  following steps:
+
+    arm-none-eabi-gdb executable.axf                  : Start GDB and name the debug image
+    target extended-remote | <debug driver> <options> : Start debug driver, connect to target
+    load                                              : Load image and download to target
+
+  The where <debug driver> is crt_emu_lpc18_43_nxp for LPC18xx and LPC43xx.
+  Your PATH variable should be set up so that the debug driver executable
+  can be found.  For my installation, the driver for the LPC18xx and LPC43xx
+  is located at:
 
     /cygdrive/c/code_red/RedSuite_4.2.3_379/redsuite/bin/crt_emu_lpc18_43_nxp.exe
 
-  The 128K free version only supports the LPC-Link and RedProbe debug probes.
-  Other JTAG interfaces are supported in the full version.
+  And <options> are:
+
+    -n set information level for the debug driver. n should be 2, 3 or 4.
+        2 should be sufficient in most circumstances 
+
+    -p<part> is the target device to connect to and you should use
+        <part>=LPC4330.
+
+    -wire=<probe> specifies the debug probe.  For LPCLink on Windows 7 use
+        <probe>=winusb.  The 128K free version only supports the LPC-Link
+        and RedProbe debug probes. Other JTAG interfaces are supported in
+        the full version.
+
+  Thus the correct invocation for the LPC4330 under Windows7 would be:
+
+    target extended-remote | crt_emu_lpc18_43_nxp -2 -pLPC4330 -wire=winusb
+
+  NOTE:  Don't forget to enable CONFIG_DEBUG_SYMBOLS=y in your NuttX
+  configuration file when you build NuttX.  That option is necessary to build
+  in debugging symbols.
 
 NuttX buildroot Toolchain
 =========================

configs/lpc4330-xplorer/ostest/setenv.sh

@@ -52,11 +52,13 @@ fi
 # Code Red toolchain in any other location or if you install a different
 # version
 export TOOLCHAIN_BIN="/cygdrive/c/code_red/RedSuite_4.2.3_379/redsuite/Tools/bin"
+export REDSUITE_BIN="/cygdrive/c/code_red/RedSuite_4.2.3_379/redsuite/bin"
 
 # This the Cygwin path to the location where I installed the CodeSourcery
 # toolchain under windows.  You will also have to edit this if you install
 # the CodeSourcery toolchain in any other location
 #export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+#export REDSUITE_BIN=
 
 # These are the Cygwin paths to the locations where I installed the Atollic
 # toolchain under windows.  You will also have to edit this if you install
@@ -65,12 +67,20 @@ export TOOLCHAIN_BIN="/cygdrive/c/code_red/RedSuite_4.2.3_379/redsuite/Tools/bin
 # at those locations as well.
 #export TOOLCHAIN_BIN="/usr/bin:/cygdrive/c/Program Files (x86)/Atollic/TrueSTUDIO for ARM Pro 2.3.0/ARMTools/bin"
 #export TOOLCHAIN_BIN="/usr/bin:/cygdrive/c/Program Files (x86)/Atollic/TrueSTUDIO for STMicroelectronics STM32 Lite 2.3.0/ARMTools/bin"
+#export REDSUITE_BIN=
 
 # This the Cygwin path to the location where I build the buildroot
 # toolchain.
 #export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
+#export REDSUITE_BIN=
 
-# Andd add the selected toolchain path to the PATH variable
+# And add the selected toolchain path[s] to the PATH variable
 
-export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+export PATH="/sbin:/usr/sbin:${PATH_ORIG}"
+
+if [ ! -z ${REDSUITE_BIN} ]; then
+  export PATH="${REDSUITE_BIN}:${PATH}"
+fi
+
+export PATH="${TOOLCHAIN_BIN}:${PATH}"
 echo "PATH : ${PATH}"

configs/lpcxpresso-lpc1768/README.txt

@@ -307,8 +307,7 @@ Code Red IDE
 ^^^^^^^^^^^^
 
   NuttX is built using command-line make.  It can be used with an IDE, but some
-  effort will be required to create the project (There is a simple RIDE project
-  in the RIDE subdirectory).
+  effort will be required to create the project.
   
   Makefile Build
   --------------