SAMV71-XULT: Some bugfixes from early bring-up work
This commit is contained in:
Gregory Nutt
parent
e23002fcfc
commit
834072815b
@ -128,11 +128,17 @@
|
||||
|
||||
/* Check internal SRAM configuration */
|
||||
|
||||
#if CONFIG_RAM_END > (SAM_DTCM_BASE+SAMV7_SRAM_SIZE)
|
||||
#ifdef CONFIG_ARMV7M_DTCM
|
||||
# define SRAM_BASE SAM_DTCM_BASE
|
||||
#else
|
||||
# define SRAM_BASE SAM_SRAM_BASE
|
||||
#endif
|
||||
|
||||
#if CONFIG_RAM_END > (SRAM_BASE+SAMV7_SRAM_SIZE)
|
||||
# error "CONFIG_RAM_END is beyond the end of SRAM"
|
||||
# undef CONFIG_RAM_END
|
||||
# define CONFIG_RAM_END (SAM_DTCM_BASE+SAMV7_SRAM_SIZE)
|
||||
#elif CONFIG_RAM_END < (SAM_DTCM_BASE+SAMV7_SRAM_SIZE)
|
||||
# define CONFIG_RAM_END (SRAM_BASE+SAMV7_SRAM_SIZE)
|
||||
#elif CONFIG_RAM_END < (SRAM_BASE+SAMV7_SRAM_SIZE)
|
||||
# warning "CONFIG_RAM_END is before end of SRAM... not all of SRAM used"
|
||||
#endif
|
||||
|
||||
|
||||
@ -177,13 +177,13 @@
|
||||
#if defined(CONFIG_SAMV7_UART1) && !defined(UART1_ASSIGNED)
|
||||
# define TTYS2_DEV g_uart1port /* UART1 is ttyS2 */
|
||||
# define UART1_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_UART2) && !defined(UART1_ASSIGNED)
|
||||
#elif defined(CONFIG_SAMV7_UART2) && !defined(UART2_ASSIGNED)
|
||||
# define TTYS2_DEV g_uart2port /* UART2 is ttyS2 */
|
||||
# define UART2_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_UART3) && !defined(UART1_ASSIGNED)
|
||||
#elif defined(CONFIG_SAMV7_UART3) && !defined(UART3_ASSIGNED)
|
||||
# define TTYS2_DEV g_uart3port /* UART3 is ttyS2 */
|
||||
# define UART3_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_UART4) && !defined(UART1_ASSIGNED)
|
||||
#elif defined(CONFIG_SAMV7_UART4) && !defined(UART4_ASSIGNED)
|
||||
# define TTYS2_DEV g_uart4port /* UART4 is ttyS2 */
|
||||
# define UART4_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_USART0) && !defined(USART0_ASSIGNED)
|
||||
@ -202,13 +202,13 @@
|
||||
* these could also be the console.
|
||||
*/
|
||||
|
||||
#if defined(CONFIG_SAMV7_UART2) && !defined(UART1_ASSIGNED)
|
||||
#if defined(CONFIG_SAMV7_UART2) && !defined(UART2_ASSIGNED)
|
||||
# define TTYS3_DEV g_uart2port /* UART2 is ttyS3 */
|
||||
# define UART2_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_UART3) && !defined(UART1_ASSIGNED)
|
||||
#elif defined(CONFIG_SAMV7_UART3) && !defined(UART3_ASSIGNED)
|
||||
# define TTYS3_DEV g_uart3port /* UART3 is ttyS3 */
|
||||
# define UART3_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_UART4) && !defined(UART1_ASSIGNED)
|
||||
#elif defined(CONFIG_SAMV7_UART4) && !defined(UART4_ASSIGNED)
|
||||
# define TTYS3_DEV g_uart4port /* UART4 is ttyS3 */
|
||||
# define UART4_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_USART0) && !defined(USART0_ASSIGNED)
|
||||
@ -227,10 +227,10 @@
|
||||
* these could also be the console.
|
||||
*/
|
||||
|
||||
#if defined(CONFIG_SAMV7_UART3) && !defined(UART1_ASSIGNED)
|
||||
#if defined(CONFIG_SAMV7_UART3) && !defined(UART3_ASSIGNED)
|
||||
# define TTYS4_DEV g_uart3port /* UART3 is ttyS4 */
|
||||
# define UART3_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_UART4) && !defined(UART1_ASSIGNED)
|
||||
#elif defined(CONFIG_SAMV7_UART4) && !defined(UART4_ASSIGNED)
|
||||
# define TTYS4_DEV g_uart4port /* UART4 is ttyS4 */
|
||||
# define UART4_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_USART0) && !defined(USART0_ASSIGNED)
|
||||
@ -249,7 +249,7 @@
|
||||
* of these could also be the console.
|
||||
*/
|
||||
|
||||
#if defined(CONFIG_SAMV7_UART4) && !defined(UART1_ASSIGNED)
|
||||
#if defined(CONFIG_SAMV7_UART4) && !defined(UART4_ASSIGNED)
|
||||
# define TTYS5_DEV g_uart4port /* UART4 is ttyS5 */
|
||||
# define UART4_ASSIGNED 1
|
||||
#elif defined(CONFIG_SAMV7_USART0) && !defined(USART0_ASSIGNED)
|
||||
@ -1003,7 +1003,7 @@ static int sam_interrupt(struct uart_dev_s *dev)
|
||||
int passes;
|
||||
bool handled;
|
||||
|
||||
DEBUGASSERT(dev && priv->priv);
|
||||
DEBUGASSERT(dev && dev->priv);
|
||||
priv = (struct sam_dev_s*)dev->priv;
|
||||
|
||||
/* Loop until there are no characters to be transferred or, until we have
|
||||
|
||||
@ -11,6 +11,7 @@ Contents
|
||||
- Board Features
|
||||
- Serial Console
|
||||
- LEDs and Buttons
|
||||
- Debugging
|
||||
- Configurations
|
||||
|
||||
Board Features
|
||||
@ -170,33 +171,55 @@ NOTES:
|
||||
use the SW1, PB12 has to be configured as a normal regular I/O pin in
|
||||
the MATRIX module. For more information see the SAM V71 datasheet.
|
||||
|
||||
Debugging
|
||||
=========
|
||||
|
||||
The on-board EDBG appears to work only with Atmel Studio. You can however,
|
||||
simply connect a SAM-ICE or J-Link to the JTAG/SWD connector on the board
|
||||
and that works great. The only tricky thing is getting the correct
|
||||
orientation of the JTAG connection.
|
||||
|
||||
I have been using Atmel Studio to write code to flash then I use the Segger
|
||||
J-Link GDB server to debug. I have been using the 'Device Programming' I
|
||||
available under the Atmel Studio 'Tool' menu. I have to disconnect the
|
||||
SAM-ICE while programming with the EDBG. I am sure that you could come up
|
||||
with a GDB server-only solution if you wanted.
|
||||
|
||||
I run GDB like this from the directory containing the NuttX ELF file:
|
||||
|
||||
arm-none-eabi-gdb
|
||||
(gdb) target remote localhost:2331
|
||||
(gdb) mon reset
|
||||
(gdb) file nuttx
|
||||
(gdb) ... start debugging ...
|
||||
|
||||
Configurations
|
||||
==============
|
||||
|
||||
Information Common to All Configurations
|
||||
----------------------------------------
|
||||
Each SAMV71-XULT configuration is maintained in a sub-directory and
|
||||
can be selected as follow:
|
||||
Information Common to All Configurations
|
||||
----------------------------------------
|
||||
Each SAMV71-XULT configuration is maintained in a sub-directory and
|
||||
can be selected as follow:
|
||||
|
||||
cd tools
|
||||
./configure.sh samv71-xult/<subdir>
|
||||
cd -
|
||||
. ./setenv.sh
|
||||
cd tools
|
||||
./configure.sh samv71-xult/<subdir>
|
||||
cd -
|
||||
. ./setenv.sh
|
||||
|
||||
Before sourcing the setenv.sh file above, you should examine it and perform
|
||||
edits as necessary so that TOOLCHAIN_BIN is the correct path to the directory
|
||||
than holds your toolchain binaries.
|
||||
Before sourcing the setenv.sh file above, you should examine it and perform
|
||||
edits as necessary so that TOOLCHAIN_BIN is the correct path to the directory
|
||||
than holds your toolchain binaries.
|
||||
|
||||
And then build NuttX by simply typing the following. At the conclusion of
|
||||
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.
|
||||
And then build NuttX by simply typing the following. At the conclusion of
|
||||
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.
|
||||
|
||||
make oldconfig
|
||||
make
|
||||
make oldconfig
|
||||
make
|
||||
|
||||
The <subdir> that is provided above as an argument to the tools/configure.sh
|
||||
must be is one of the following.
|
||||
The <subdir> that is provided above as an argument to the tools/configure.sh
|
||||
must be is one of the following.
|
||||
|
||||
NOTES:
|
||||
NOTES:
|
||||
|
||||
1. These configurations use the mconf-based configuration tool. To
|
||||
change any of these configurations using that tool, you should:
|
||||
@ -225,8 +248,8 @@ Configurations
|
||||
You an get the free devkitARM toolchain from http://devkitpro.org/ or
|
||||
http://sourceforge.net/projects/devkitpro/
|
||||
|
||||
Configuration sub-directories
|
||||
-----------------------------
|
||||
Configuration sub-directories
|
||||
-----------------------------
|
||||
|
||||
nsh:
|
||||
|
||||
|
||||
@ -37,6 +37,12 @@ include ${TOPDIR}/.config
|
||||
include ${TOPDIR}/tools/Config.mk
|
||||
include ${TOPDIR}/arch/arm/src/armv7-m/Toolchain.defs
|
||||
|
||||
ifeq ($(CONFIG_ARMV7M_DTCM),y)
|
||||
LDSCRIPT = flash-dtcm.ld
|
||||
else
|
||||
LDSCRIPT = flash-sram.ld
|
||||
endif
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/copydir.sh
|
||||
@ -44,13 +50,13 @@ ifeq ($(WINTOOL),y)
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/flash.ld}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)}"
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/flash.ld
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
|
||||
@ -255,7 +255,7 @@ CONFIG_ARCH_HAVE_RAMVECTORS=y
|
||||
#
|
||||
# Board Settings
|
||||
#
|
||||
CONFIG_BOARD_LOOPSPERMSEC=11990
|
||||
CONFIG_BOARD_LOOPSPERMSEC=42445
|
||||
# CONFIG_ARCH_CALIBRATION is not set
|
||||
|
||||
#
|
||||
@ -278,7 +278,7 @@ CONFIG_BOOT_RUNFROMFLASH=y
|
||||
#
|
||||
# Boot Memory Configuration
|
||||
#
|
||||
CONFIG_RAM_START=0x20000000
|
||||
CONFIG_RAM_START=0x20400000
|
||||
CONFIG_RAM_SIZE=393216
|
||||
# CONFIG_ARCH_HAVE_SDRAM is not set
|
||||
|
||||
@ -595,7 +595,7 @@ CONFIG_FAT_MAXFNAME=32
|
||||
# Memory Management
|
||||
#
|
||||
# CONFIG_MM_SMALL is not set
|
||||
CONFIG_MM_REGIONS=2
|
||||
CONFIG_MM_REGIONS=1
|
||||
# CONFIG_ARCH_HAVE_HEAP2 is not set
|
||||
# CONFIG_GRAN is not set
|
||||
|
||||
|
||||
@ -1,5 +1,5 @@
|
||||
/****************************************************************************
|
||||
* configs/samv71-xult/scripts/flash.ld
|
||||
* configs/samv71-xult/scripts/flash-dtcm.ld
|
||||
*
|
||||
* Copyright (C) 2015 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
@ -33,7 +33,7 @@
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The SAMV71Q21 has 2048Kb of FLASH beginning at address 0x0400:0000 and
|
||||
/* The SAMV71Q21 has 2048Kb of FLASH beginning at address 0x0040:0000 and
|
||||
* 384Kb of SRAM beginining at 0x2040:0000
|
||||
*
|
||||
* When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
|
||||
@ -46,12 +46,14 @@
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x04000000, LENGTH = 2048K
|
||||
flash (rx) : ORIGIN = 0x00400000, LENGTH = 2048K
|
||||
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 384K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
EXTERN(_vectors)
|
||||
ENTRY(_stext)
|
||||
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
119
configs/samv71-xult/scripts/flash-sram.ld
Normal file
119
configs/samv71-xult/scripts/flash-sram.ld
Normal file
@ -0,0 +1,119 @@
|
||||
/****************************************************************************
|
||||
* configs/samv71-xult/scripts/flash-sram.ld
|
||||
*
|
||||
* Copyright (C) 2015 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The SAMV71Q21 has 2048Kb of FLASH beginning at address 0x0040:0000 and
|
||||
* 384Kb of SRAM beginining at 0x2040:0000
|
||||
*
|
||||
* When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
|
||||
* where the code expects to begin execution by jumping to the entry point in
|
||||
* the 0x0400:0000 address range (Assuming that ITCM is not enable).
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
flash (rx) : ORIGIN = 0x00400000, LENGTH = 2048K
|
||||
sram (rwx) : ORIGIN = 0x20400000, LENGTH = 384K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
EXTERN(_vectors)
|
||||
ENTRY(_stext)
|
||||
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
.init_section : {
|
||||
_sinit = ABSOLUTE(.);
|
||||
*(.init_array .init_array.*)
|
||||
_einit = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} > flash
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} > flash
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram AT > flash
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
||||
@ -38,7 +38,9 @@
|
||||
*/
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
EXTERN(_vectors)
|
||||
ENTRY(_stext)
|
||||
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
|
||||
@ -33,7 +33,7 @@
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The SAMV71Q21 has 2048Kb of FLASH beginning at address 0x0400:0000 and
|
||||
/* The SAMV71Q21 has 2048Kb of FLASH beginning at address 0x0040:0000 and
|
||||
* 384Kb of SRAM beginining at 0x2040:0000
|
||||
*
|
||||
* When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
|
||||
@ -73,8 +73,8 @@ MEMORY
|
||||
{
|
||||
/* 2048KiB of internal FLASH */
|
||||
|
||||
kflash (rx) : ORIGIN = 0x04000000, LENGTH = 1M
|
||||
uflash (rx) : ORIGIN = 0x04100000, LENGTH = 1M
|
||||
kflash (rx) : ORIGIN = 0x00400000, LENGTH = 1M
|
||||
uflash (rx) : ORIGIN = 0x00500000, LENGTH = 1M
|
||||
|
||||
/* 384Kb of internal SRAM */
|
||||
|
||||
|
||||
@ -131,9 +131,9 @@
|
||||
* ------ ----------- ---------------------
|
||||
*/
|
||||
|
||||
#define GPIO_LED0 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
|
||||
#define GPIO_LED0 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
|
||||
GPIO_PORT_PIOA | GPIO_PIN23)
|
||||
#define GPIO_LED1 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
|
||||
#define GPIO_LED1 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
|
||||
GPIO_PORT_PIOC | GPIO_PIN9)
|
||||
|
||||
/* Buttons
|
||||
|
||||
Loading…
Reference in New Issue
Block a user