SAMA5: Alternatie clock configuration that yields a perfect 48MHz full speed USB clock and a CPU clock of 384MHz
This commit is contained in:
Gregory Nutt
parent
0c1d2ed2b8
commit
8686c040ac
@ -47,139 +47,27 @@
|
|||||||
************************************************************************************/
|
************************************************************************************/
|
||||||
|
|
||||||
/* Clocking *************************************************************************/
|
/* Clocking *************************************************************************/
|
||||||
/* After power-on reset, the sam3u device is running on a 4MHz internal RC. These
|
/* After power-on reset, the SAMA5 device is running on a 12MHz internal RC. These
|
||||||
* definitions will configure clocking
|
* definitions will configure operational clocking.
|
||||||
*
|
|
||||||
* MAINOSC: Frequency = 12MHz (crysta)
|
|
||||||
* PLLA: PLL Divider = 1, Multiplier = 66 to generate PLLACK = 792MHz
|
|
||||||
* Master Clock (MCK): Source = PLLACK/2, Prescalar = 1, MDIV = 3 to generate
|
|
||||||
* MCK = 132MHz
|
|
||||||
* CPU clock = 396MHz
|
|
||||||
*/
|
*/
|
||||||
|
|
||||||
/* Main oscillator register settings.
|
#ifndef CONFIG_SAMA5_OHCI
|
||||||
*
|
/* This is the configuration provided in the Atmel example code. This setup results
|
||||||
* The start up time should be should be:
|
* in a CPU clock of 396MHz
|
||||||
* Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles.
|
|
||||||
*/
|
*/
|
||||||
|
|
||||||
#define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */
|
# include <arch/board/board_396MHz.h>
|
||||||
|
|
||||||
/* PLLA configuration.
|
#else
|
||||||
*
|
/* This is an alternative slower configuration that will produce a 48MHz USB clock
|
||||||
* Divider = 1
|
* with the required accuracy. When used with OHCI, an additional requirement is
|
||||||
* Multipler = 66
|
* the PLLACK be a multiple of 48MHz. This setup results in a CPU clock of 384MHz.
|
||||||
*/
|
*/
|
||||||
|
|
||||||
#define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT)
|
# include <arch/board/board_384MHz.h>
|
||||||
#define BOARD_CKGR_PLLAR_OUT (0)
|
|
||||||
#define BOARD_CKGR_PLLAR_MUL (65 << PMC_CKGR_PLLAR_MUL_SHIFT)
|
|
||||||
#define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS
|
|
||||||
|
|
||||||
/* PMC master clock register settings.
|
|
||||||
*
|
|
||||||
* Master/Processor Clock Source Selection = PLLA
|
|
||||||
* Master/Processor Clock Prescaler = 1
|
|
||||||
* PLLA Divider = 2
|
|
||||||
* Master Clock Division (MDIV) = 3
|
|
||||||
*
|
|
||||||
* NOTE: Bit PLLADIV2 must always be set to 1 when MDIV is set to 3.
|
|
||||||
*
|
|
||||||
* Prescaler input = 792MHz / 2 = 396MHz
|
|
||||||
* Prescaler output = 792MHz / 1 = 396MHz
|
|
||||||
* Processor Clock (PCK) = 396MHz
|
|
||||||
* Master clock (MCK) = 396MHz / 3 = 132MHz
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA
|
|
||||||
#define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV1
|
|
||||||
#define BOARD_PMC_MCKR_PLLADIV PMC_MCKR_PLLADIV2
|
|
||||||
#define BOARD_PMC_MCKR_MDIV PMC_MCKR_MDIV_PCKDIV3
|
|
||||||
|
|
||||||
#ifdef CONFIG_SAMA5_OHCI
|
|
||||||
/* For OHCI Full-speed operations, the user has to perform the following:
|
|
||||||
*
|
|
||||||
* 1) Enable UHP peripheral clock, bit (1 << AT91C_ID_UHPHS) in PMC_PCER
|
|
||||||
* register.
|
|
||||||
* 2) Select PLLACK as Input clock of OHCI part, USBS bit in PMC_USB
|
|
||||||
* register.
|
|
||||||
* 3) Program the OHCI clocks (UHP48M and UHP12M) with USBDIV field in
|
|
||||||
* PMC_USB register. USBDIV value is calculated regarding the PLLACK
|
|
||||||
* value and USB Full-speed accuracy.
|
|
||||||
* 4) Enable the OHCI clocks, UHP bit in PMC_SCER register.
|
|
||||||
*
|
|
||||||
* "The USB Host controller requires 48 MHz and 12 MHz clocks for OHCI
|
|
||||||
* full-speed operations. These clocks must be generated by a PLL with a
|
|
||||||
* correct accuracy of ± 0.25% thanks to USBDIV field.
|
|
||||||
*
|
|
||||||
* "Thus the USB Host peripheral receives three clocks from the Power
|
|
||||||
* Management Controller (PMC): the Peripheral Clock (MCK domain), the
|
|
||||||
* UHP48M and the UHP12M (built-in UHP48M divided by four) used by the
|
|
||||||
* OHCI to interface with the bus USB signals (Recovered 12 MHz domain)
|
|
||||||
* in Full-speed operations"
|
|
||||||
*
|
|
||||||
* USB Clock = PLLACK / (USBDIV + 1) = 48MHz
|
|
||||||
* USBDIV = PLLACK / 48MHz - 1
|
|
||||||
* = 15.5
|
|
||||||
*
|
|
||||||
* The maximum value of USBDIV is 15 corresponding to a divisor of 16.
|
|
||||||
* REVISIT: USBDIV = 15 gives a clock of 49.5MHz which is an error of 3%
|
|
||||||
*/
|
|
||||||
|
|
||||||
# define BOARD_OHCI_INPUT PMC_USB_USBS_PLLA
|
|
||||||
# define BOARD_OHCI_DIVIDER (15)
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if 0
|
|
||||||
/* USB UTMI PLL start-up time */
|
|
||||||
|
|
||||||
#define BOARD_CKGR_UCKR_UPLLCOUNT (3 << PMC_CKGR_UCKR_UPLLCOUNT_SHIFT)
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/* Resulting frequencies */
|
|
||||||
|
|
||||||
#define BOARD_MAINOSC_FREQUENCY (12000000) /* MAINOSC: 12MHz crystal on-board */
|
|
||||||
#define BOARD_PLLA_FREQUENCY (792000000) /* PLLACK: 66 * 12Mhz / 1 */
|
|
||||||
#define BOARD_PCK_FREQUENCY (396000000) /* CPU: PLLACK / 2 / 1 */
|
|
||||||
#define BOARD_MCK_FREQUENCY (132000000) /* MCK: PLLACK / 2 / 1 / 3 */
|
|
||||||
|
|
||||||
/* HSMCI clocking
|
|
||||||
*
|
|
||||||
* Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK)
|
|
||||||
* divided by (2*(CLKDIV+1)).
|
|
||||||
*
|
|
||||||
* MCI_SPEED = MCK / (2*(CLKDIV+1))
|
|
||||||
* CLKDIV = MCI / MCI_SPEED / 2 - 1
|
|
||||||
*
|
|
||||||
* Where CLKDIV has a range of 0-255.
|
|
||||||
*/
|
|
||||||
|
|
||||||
/* MCK = 96MHz, CLKDIV = 119, MCI_SPEED = 96MHz / 2 * (119+1) = 400 KHz */
|
|
||||||
|
|
||||||
#define HSMCI_INIT_CLKDIV (119 << HSMCI_MR_CLKDIV_SHIFT)
|
|
||||||
|
|
||||||
/* MCK = 96MHz, CLKDIV = 3, MCI_SPEED = 96MHz / 2 * (3+1) = 12 MHz */
|
|
||||||
|
|
||||||
#define HSMCI_MMCXFR_CLKDIV (3 << HSMCI_MR_CLKDIV_SHIFT)
|
|
||||||
|
|
||||||
/* MCK = 96MHz, CLKDIV = 1, MCI_SPEED = 96MHz / 2 * (1+1) = 24 MHz */
|
|
||||||
|
|
||||||
#define HSMCI_SDXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT)
|
|
||||||
#define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV
|
|
||||||
|
|
||||||
/* FLASH wait states
|
|
||||||
*
|
|
||||||
* FWS Max frequency
|
|
||||||
* 1.62V 1.8V
|
|
||||||
* --- ----- ------
|
|
||||||
* 0 24MHz 27MHz
|
|
||||||
* 1 40MHz 47MHz
|
|
||||||
* 2 72MHz 84MHz
|
|
||||||
* 3 84MHz 96MHz
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define BOARD_FWS 3
|
|
||||||
|
|
||||||
/* LED definitions ******************************************************************/
|
/* LED definitions ******************************************************************/
|
||||||
/* There are two LEDs on the SAMA5D3 series-CM board that can be controlled
|
/* There are two LEDs on the SAMA5D3 series-CM board that can be controlled
|
||||||
* by software. A blue LED is controlled via PIO pins. A red LED normally
|
* by software. A blue LED is controlled via PIO pins. A red LED normally
|
||||||
|
|||||||
202
configs/sama5d3x-ek/include/board_384mhz.h
Normal file
202
configs/sama5d3x-ek/include/board_384mhz.h
Normal file
@ -0,0 +1,202 @@
|
|||||||
|
/************************************************************************************
|
||||||
|
* configs/sama5df3x-ek/include/board_384mhz.h
|
||||||
|
*
|
||||||
|
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
|
||||||
|
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||||
|
*
|
||||||
|
* Redistribution and use in source and binary forms, with or without
|
||||||
|
* modification, are permitted provided that the following conditions
|
||||||
|
* are met:
|
||||||
|
*
|
||||||
|
* 1. Redistributions of source code must retain the above copyright
|
||||||
|
* notice, this list of conditions and the following disclaimer.
|
||||||
|
* 2. Redistributions in binary form must reproduce the above copyright
|
||||||
|
* notice, this list of conditions and the following disclaimer in
|
||||||
|
* the documentation and/or other materials provided with the
|
||||||
|
* distribution.
|
||||||
|
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||||
|
* used to endorse or promote products derived from this software
|
||||||
|
* without specific prior written permission.
|
||||||
|
*
|
||||||
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||||
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||||
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||||
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||||
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||||
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||||
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||||
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||||
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||||
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||||
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||||
|
* POSSIBILITY OF SUCH DAMAGE.
|
||||||
|
*
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
#ifndef __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_384MHZ_H
|
||||||
|
#define __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_384MHZ_H
|
||||||
|
|
||||||
|
/************************************************************************************
|
||||||
|
* Included Files
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
#include <nuttx/config.h>
|
||||||
|
|
||||||
|
/************************************************************************************
|
||||||
|
* Definitions
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
/* Clocking *************************************************************************/
|
||||||
|
/* After power-on reset, the SAMA5 device is running on a 12MHz internal RC. These
|
||||||
|
* definitions will configure operational clocking.
|
||||||
|
*
|
||||||
|
* This is an alternative slower configuration that will produce a 48MHz USB clock
|
||||||
|
* with the required accuracy. When used with OHCI, an additional requirement is
|
||||||
|
* the PLLACK be a multiple of 48MHz. This setup results in a CPU clock of 384MHz.
|
||||||
|
*
|
||||||
|
* MAINOSC: Frequency = 12MHz (crystal)
|
||||||
|
* PLLA: PLL Divider = 1, Multiplier = 64 to generate PLLACK = 768MHz
|
||||||
|
* Master Clock (MCK): Source = PLLACK/2, Prescalar = 1, MDIV = 3 to generate
|
||||||
|
* MCK = 128MHz
|
||||||
|
* CPU clock = 384MHz
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* Main oscillator register settings.
|
||||||
|
*
|
||||||
|
* The start up time should be should be:
|
||||||
|
* Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles.
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */
|
||||||
|
|
||||||
|
/* PLLA configuration.
|
||||||
|
*
|
||||||
|
* Divider = 1
|
||||||
|
* Multipler = 64
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT)
|
||||||
|
#define BOARD_CKGR_PLLAR_OUT (0)
|
||||||
|
#define BOARD_CKGR_PLLAR_MUL (63 << PMC_CKGR_PLLAR_MUL_SHIFT)
|
||||||
|
#define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS
|
||||||
|
|
||||||
|
/* PMC master clock register settings.
|
||||||
|
*
|
||||||
|
* Master/Processor Clock Source Selection = PLLA
|
||||||
|
* Master/Processor Clock Prescaler = 1
|
||||||
|
* PLLA Divider = 2
|
||||||
|
* Master Clock Division (MDIV) = 3
|
||||||
|
*
|
||||||
|
* NOTE: Bit PLLADIV2 must always be set to 1 when MDIV is set to 3.
|
||||||
|
*
|
||||||
|
* Prescaler input = 768MHz / 2 = 384MHz
|
||||||
|
* Prescaler output = 768MHz / 1 = 384MHz
|
||||||
|
* Processor Clock (PCK) = 384MHz
|
||||||
|
* Master clock (MCK) = 396MHz / 3 = 129MHz
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA
|
||||||
|
#define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV1
|
||||||
|
#define BOARD_PMC_MCKR_PLLADIV PMC_MCKR_PLLADIV2
|
||||||
|
#define BOARD_PMC_MCKR_MDIV PMC_MCKR_MDIV_PCKDIV3
|
||||||
|
|
||||||
|
/* For OHCI Full-speed operations, the user has to perform the following:
|
||||||
|
*
|
||||||
|
* 1) Enable UHP peripheral clock, bit (1 << AT91C_ID_UHPHS) in PMC_PCER
|
||||||
|
* register.
|
||||||
|
* 2) Select PLLACK as Input clock of OHCI part, USBS bit in PMC_USB
|
||||||
|
* register.
|
||||||
|
* 3) Program the OHCI clocks (UHP48M and UHP12M) with USBDIV field in
|
||||||
|
* PMC_USB register. USBDIV value is calculated regarding the PLLACK
|
||||||
|
* value and USB Full-speed accuracy.
|
||||||
|
* 4) Enable the OHCI clocks, UHP bit in PMC_SCER register.
|
||||||
|
*
|
||||||
|
* "The USB Host controller requires 48 MHz and 12 MHz clocks for OHCI
|
||||||
|
* full-speed operations. These clocks must be generated by a PLL with a
|
||||||
|
* correct accuracy of ± 0.25% thanks to USBDIV field.
|
||||||
|
*
|
||||||
|
* "Thus the USB Host peripheral receives three clocks from the Power
|
||||||
|
* Management Controller (PMC): the Peripheral Clock (MCK domain), the
|
||||||
|
* UHP48M and the UHP12M (built-in UHP48M divided by four) used by the
|
||||||
|
* OHCI to interface with the bus USB signals (Recovered 12 MHz domain)
|
||||||
|
* in Full-speed operations"
|
||||||
|
*
|
||||||
|
* USB Clock = PLLACK / (USBDIV + 1) = 48MHz
|
||||||
|
* USBDIV = PLLACK / 48MHz - 1
|
||||||
|
* = 16
|
||||||
|
*
|
||||||
|
* The maximum value of USBDIV is 15 corresponding to a divisor of 16.
|
||||||
|
* REVISIT: USBDIV = 15 gives an exact clock of 48MHz.
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_OHCI_INPUT PMC_USB_USBS_PLLA
|
||||||
|
#define BOARD_OHCI_DIVIDER (15)
|
||||||
|
|
||||||
|
/* Resulting frequencies */
|
||||||
|
|
||||||
|
#define BOARD_MAINOSC_FREQUENCY (12000000) /* MAINOSC: 12MHz crystal on-board */
|
||||||
|
#define BOARD_PLLA_FREQUENCY (768000000) /* PLLACK: 64 * 12Mhz / 1 */
|
||||||
|
#define BOARD_PCK_FREQUENCY (384000000) /* CPU: PLLACK / 2 / 1 */
|
||||||
|
#define BOARD_MCK_FREQUENCY (128000000) /* MCK: PLLACK / 2 / 1 / 3 */
|
||||||
|
|
||||||
|
/* HSMCI clocking
|
||||||
|
*
|
||||||
|
* Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK)
|
||||||
|
* divided by (2*(CLKDIV) + CLOCKODD + 2).
|
||||||
|
*
|
||||||
|
* MCI_SPEED = MCK / (2*CLKDIV + CLOCKODD + 2)
|
||||||
|
*
|
||||||
|
* Where CLKDIV has a range of 0-255.
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* MCK = 128MHz, CLKDIV = 159, MCI_SPEED = 128MHz / (2*159 + 0 + 2) = 400 KHz */
|
||||||
|
|
||||||
|
#define HSMCI_INIT_CLKDIV (159 << HSMCI_MR_CLKDIV_SHIFT)
|
||||||
|
|
||||||
|
/* MCK = 128MHz, CLKDIV = 2 w/CLOCKODD, MCI_SPEED = 128MHz /(2*2 + 1 + 2) = 18.3 MHz */
|
||||||
|
|
||||||
|
#define HSMCI_MMCXFR_CLKDIV ((2 << HSMCI_MR_CLKDIV_SHIFT) | HSMCI_MR_CLKODD)
|
||||||
|
|
||||||
|
/* MCK = 128MHz, CLKDIV = 2, MCI_SPEED = 128MHz /(2*2 + 0 + 2) = 21.3 MHz */
|
||||||
|
|
||||||
|
#define HSMCI_SDXFR_CLKDIV (2 << HSMCI_MR_CLKDIV_SHIFT)
|
||||||
|
#define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV
|
||||||
|
|
||||||
|
/* FLASH wait states
|
||||||
|
*
|
||||||
|
* FWS Max frequency
|
||||||
|
* 1.62V 1.8V
|
||||||
|
* --- ----- ------
|
||||||
|
* 0 24MHz 27MHz
|
||||||
|
* 1 40MHz 47MHz
|
||||||
|
* 2 72MHz 84MHz
|
||||||
|
* 3 84MHz 96MHz
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_FWS 3
|
||||||
|
|
||||||
|
/************************************************************************************
|
||||||
|
* Public Data
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
#ifndef __ASSEMBLY__
|
||||||
|
|
||||||
|
#undef EXTERN
|
||||||
|
#if defined(__cplusplus)
|
||||||
|
#define EXTERN extern "C"
|
||||||
|
extern "C" {
|
||||||
|
#else
|
||||||
|
#define EXTERN extern
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/************************************************************************************
|
||||||
|
* Public Function Prototypes
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
#undef EXTERN
|
||||||
|
#if defined(__cplusplus)
|
||||||
|
}
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif /* !__ASSEMBLY__ */
|
||||||
|
#endif /* __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_384MHZ_H */
|
||||||
169
configs/sama5d3x-ek/include/board_396mhz.h
Normal file
169
configs/sama5d3x-ek/include/board_396mhz.h
Normal file
@ -0,0 +1,169 @@
|
|||||||
|
/************************************************************************************
|
||||||
|
* configs/sama5df3x-ek/include/board_396mhz.h
|
||||||
|
*
|
||||||
|
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
|
||||||
|
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||||
|
*
|
||||||
|
* Redistribution and use in source and binary forms, with or without
|
||||||
|
* modification, are permitted provided that the following conditions
|
||||||
|
* are met:
|
||||||
|
*
|
||||||
|
* 1. Redistributions of source code must retain the above copyright
|
||||||
|
* notice, this list of conditions and the following disclaimer.
|
||||||
|
* 2. Redistributions in binary form must reproduce the above copyright
|
||||||
|
* notice, this list of conditions and the following disclaimer in
|
||||||
|
* the documentation and/or other materials provided with the
|
||||||
|
* distribution.
|
||||||
|
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||||
|
* used to endorse or promote products derived from this software
|
||||||
|
* without specific prior written permission.
|
||||||
|
*
|
||||||
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||||
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||||
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||||
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||||
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||||
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||||
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||||
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||||
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||||
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||||
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||||
|
* POSSIBILITY OF SUCH DAMAGE.
|
||||||
|
*
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
#ifndef __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_396MHZ_H
|
||||||
|
#define __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_396MHZ_H
|
||||||
|
|
||||||
|
/************************************************************************************
|
||||||
|
* Included Files
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
#include <nuttx/config.h>
|
||||||
|
|
||||||
|
/************************************************************************************
|
||||||
|
* Definitions
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
/* Clocking *************************************************************************/
|
||||||
|
/* After power-on reset, the SAMA5 device is running on a 12MHz internal RC. These
|
||||||
|
* definitions will configure operational clocking.
|
||||||
|
*
|
||||||
|
* This is the configuration provided in the Atmel example code. This results in a
|
||||||
|
* CPU clock of 396MHz:
|
||||||
|
*
|
||||||
|
* MAINOSC: Frequency = 12MHz (crystal)
|
||||||
|
* PLLA: PLL Divider = 1, Multiplier = 66 to generate PLLACK = 792MHz
|
||||||
|
* Master Clock (MCK): Source = PLLACK/2, Prescalar = 1, MDIV = 3 to generate
|
||||||
|
* MCK = 132MHz
|
||||||
|
* CPU clock = 396MHz
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* Main oscillator register settings.
|
||||||
|
*
|
||||||
|
* The start up time should be should be:
|
||||||
|
* Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles.
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */
|
||||||
|
|
||||||
|
/* PLLA configuration.
|
||||||
|
*
|
||||||
|
* Divider = 1
|
||||||
|
* Multipler = 66
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT)
|
||||||
|
#define BOARD_CKGR_PLLAR_OUT (0)
|
||||||
|
#define BOARD_CKGR_PLLAR_MUL (65 << PMC_CKGR_PLLAR_MUL_SHIFT)
|
||||||
|
#define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS
|
||||||
|
|
||||||
|
/* PMC master clock register settings.
|
||||||
|
*
|
||||||
|
* Master/Processor Clock Source Selection = PLLA
|
||||||
|
* Master/Processor Clock Prescaler = 1
|
||||||
|
* PLLA Divider = 2
|
||||||
|
* Master Clock Division (MDIV) = 3
|
||||||
|
*
|
||||||
|
* NOTE: Bit PLLADIV2 must always be set to 1 when MDIV is set to 3.
|
||||||
|
*
|
||||||
|
* Prescaler input = 792MHz / 2 = 396MHz
|
||||||
|
* Prescaler output = 792MHz / 1 = 396MHz
|
||||||
|
* Processor Clock (PCK) = 396MHz
|
||||||
|
* Master clock (MCK) = 396MHz / 3 = 132MHz
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA
|
||||||
|
#define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV1
|
||||||
|
#define BOARD_PMC_MCKR_PLLADIV PMC_MCKR_PLLADIV2
|
||||||
|
#define BOARD_PMC_MCKR_MDIV PMC_MCKR_MDIV_PCKDIV3
|
||||||
|
786
|
||||||
|
/* Resulting frequencies */
|
||||||
|
|
||||||
|
#define BOARD_MAINOSC_FREQUENCY (12000000) /* MAINOSC: 12MHz crystal on-board */
|
||||||
|
#define BOARD_PLLA_FREQUENCY (792000000) /* PLLACK: 66 * 12Mhz / 1 */
|
||||||
|
#define BOARD_PCK_FREQUENCY (396000000) /* CPU: PLLACK / 2 / 1 */
|
||||||
|
#define BOARD_MCK_FREQUENCY (132000000) /* MCK: PLLACK / 2 / 1 / 3 */
|
||||||
|
|
||||||
|
/* HSMCI clocking
|
||||||
|
*
|
||||||
|
* Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK)
|
||||||
|
* divided by (2*(CLKDIV) + CLOCKODD + 2).
|
||||||
|
*
|
||||||
|
* MCI_SPEED = MCK / (2*CLKDIV + CLOCKODD + 2)
|
||||||
|
*
|
||||||
|
* Where CLKDIV has a range of 0-255.
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* MCK = 132MHz, CLKDIV = 164, MCI_SPEED = 132MHz / (2*164 + 0 + 2) = 400 KHz */
|
||||||
|
|
||||||
|
#define HSMCI_INIT_CLKDIV (164 << HSMCI_MR_CLKDIV_SHIFT)
|
||||||
|
|
||||||
|
/* MCK = 132MHz, CLKDIV = 2 w/CLOCKODD, MCI_SPEED = 132MHz /(2*2 + 1 + 2) = 18.9 MHz */
|
||||||
|
|
||||||
|
#define HSMCI_MMCXFR_CLKDIV ((2 << HSMCI_MR_CLKDIV_SHIFT) | HSMCI_MR_CLKODD)
|
||||||
|
|
||||||
|
/* MCK = 132MHz, CLKDIV = 2, MCI_SPEED = 132MHz /(2*2 + 0 + 2) = 22 MHz */
|
||||||
|
|
||||||
|
#define HSMCI_SDXFR_CLKDIV (2 << HSMCI_MR_CLKDIV_SHIFT)
|
||||||
|
#define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV
|
||||||
|
|
||||||
|
/* FLASH wait states
|
||||||
|
*
|
||||||
|
* FWS Max frequency
|
||||||
|
* 1.62V 1.8V
|
||||||
|
* --- ----- ------
|
||||||
|
* 0 24MHz 27MHz
|
||||||
|
* 1 40MHz 47MHz
|
||||||
|
* 2 72MHz 84MHz
|
||||||
|
* 3 84MHz 96MHz
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_FWS 3
|
||||||
|
|
||||||
|
/************************************************************************************
|
||||||
|
* Public Data
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
#ifndef __ASSEMBLY__
|
||||||
|
|
||||||
|
#undef EXTERN
|
||||||
|
#if defined(__cplusplus)
|
||||||
|
#define EXTERN extern "C"
|
||||||
|
extern "C" {
|
||||||
|
#else
|
||||||
|
#define EXTERN extern
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/************************************************************************************
|
||||||
|
* Public Function Prototypes
|
||||||
|
************************************************************************************/
|
||||||
|
|
||||||
|
#undef EXTERN
|
||||||
|
#if defined(__cplusplus)
|
||||||
|
}
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif /* !__ASSEMBLY__ */
|
||||||
|
#endif /* __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_396MHZ_H */
|
||||||
Loading…
Reference in New Issue
Block a user