Incremental progress on STM32 MMCSD driver
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@2245 42af7a65-404d-4744-a932-0658087f49c3
This commit is contained in:
patacongo
parent
a18a6c13c9
commit
911672589d
@ -55,6 +55,25 @@
|
||||
* Pre-Processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Friendly CLKCR bit re-definitions ****************************************/
|
||||
|
||||
#define SDIO_CLKCR_RISINGEDGE (0)
|
||||
#define SDIO_CLKCR_FALLINGEDGE SDIO_CLKCR_NEGEDGE
|
||||
|
||||
/* HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz */
|
||||
|
||||
#define SDIO_INIT_CLKDIV (178 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||||
#define STM32_CLCKCR_INIT \
|
||||
(SDIO_INIT_CLKDIV|SDIO_CLKCR_RISINGEDGE|SDIO_CLKCR_WIDBUS_D1)
|
||||
|
||||
/* HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz */
|
||||
|
||||
#define SDIO_TRANSFER_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||||
#define STM32_CLCKCR_TRANSFER \
|
||||
(SDIO_TRANSFER_CLKDIV|SDIO_CLKCR_RISINGEDGE|SDIO_CLKCR_WIDBUS_D1)
|
||||
#define STM32_CLKCR_WIDETRANSFER \
|
||||
(SDIO_TRANSFER_CLKDIV|SDIO_CLKCR_RISINGEDGE|SDIO_CLKCR_WIDBUS_D4)
|
||||
|
||||
/****************************************************************************
|
||||
* Private Types
|
||||
****************************************************************************/
|
||||
@ -66,12 +85,20 @@ struct stm32_dev_s
|
||||
struct sdio_dev_s dev; /* Standard, base MMC/SD interface */
|
||||
|
||||
/* STM32-specific extensions */
|
||||
|
||||
ubyte type; /* Card type (see MMCSD_CARDTYPE_ definitions) */
|
||||
};
|
||||
|
||||
/****************************************************************************
|
||||
* Private Function Prototypes
|
||||
****************************************************************************/
|
||||
|
||||
/* Low-level helpers ********************************************************/
|
||||
|
||||
static inline void stm32_setclkcr(uint32 clkcr);
|
||||
static inline void stm32_enableint(uint32 bitset);
|
||||
static inline void stm32_disableint(uint32 bitset);
|
||||
|
||||
/* SDIO interface methods ***************************************************/
|
||||
|
||||
/* Initialization/setup */
|
||||
@ -87,7 +114,7 @@ static int stm32_attach(FAR struct sdio_dev_s *dev);
|
||||
|
||||
/* Command/Status/Data Transfer */
|
||||
|
||||
static void stm32_sendcmd(FAR struct sdio_dev_s *dev, ubyte cmd,
|
||||
static void stm32_sendcmd(FAR struct sdio_dev_s *dev, uint32 cmd,
|
||||
uint32 arg, FAR const ubyte *data);
|
||||
static int stm32_senddata(FAR struct sdio_dev_s *dev,
|
||||
FAR const ubyte *buffer);
|
||||
@ -175,6 +202,91 @@ struct stm32_dev_s g_mmcsd =
|
||||
* Private Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Low-level Helpers
|
||||
****************************************************************************/
|
||||
/****************************************************************************
|
||||
* Name: stm32_setclkcr
|
||||
*
|
||||
* Description:
|
||||
* Modify oft-changed bits in the CLKCR register. Only the following bit-
|
||||
* fields are changed:
|
||||
*
|
||||
* CLKDIV, PWRSAV, BYPASS, WIDBUS, NEGEDGE, and HWFC_EN
|
||||
*
|
||||
* Input Parameters:
|
||||
* clkcr - A new CLKCR setting for the above mentions bits (other bits
|
||||
* are ignored.
|
||||
*
|
||||
* Returned Value:
|
||||
* None
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
static inline void stm32_setclkcr(uint32 clkcr)
|
||||
{
|
||||
uint32 regval = getreg32(STM32_SDIO_CLKCR);
|
||||
|
||||
/* Clear CLKDIV, PWRSAV, BYPASS, WIDBUS, NEGEDGE, HWFC_EN bits */
|
||||
|
||||
regval &= ~(SDIO_CLKCR_CLKDIV_MASK|SDIO_CLKCR_PWRSAV|SDIO_CLKCR_BYPASS|
|
||||
SDIO_CLKCR_WIDBUS_MASK|SDIO_CLKCR_NEGEDGE|SDIO_CLKCR_HWFC_EN);
|
||||
|
||||
/* Replace with user provided settings */
|
||||
|
||||
clkcr &= (SDIO_CLKCR_CLKDIV_MASK|SDIO_CLKCR_PWRSAV|SDIO_CLKCR_BYPASS|
|
||||
SDIO_CLKCR_WIDBUS_MASK|SDIO_CLKCR_NEGEDGE|SDIO_CLKCR_HWFC_EN);
|
||||
regval |= clkcr;
|
||||
putreg32(regval, STM32_SDIO_CLKCR);
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: stm32_enableint
|
||||
*
|
||||
* Description:
|
||||
* Enable SDIO interrupts
|
||||
*
|
||||
* Input Parameters:
|
||||
* bitset - The set of bits in the SDIO MASK register to set
|
||||
*
|
||||
* Returned Value:
|
||||
* None
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
static inline void stm32_enableint(uint32 bitset)
|
||||
{
|
||||
uint32 regval;
|
||||
regval = getreg32(STM32_SDIO_MASK);
|
||||
regval |= bitset;
|
||||
putreg32(regval, STM32_SDIO_MASK);
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: stm32_disableint
|
||||
*
|
||||
* Description:
|
||||
* Disable SDIO interrupts
|
||||
*
|
||||
* Input Parameters:
|
||||
* bitset - The set of bits in the SDIO MASK register to clear
|
||||
*
|
||||
* Returned Value:
|
||||
* None
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
static inline void stm32_disableint(uint32 bitset)
|
||||
{
|
||||
uint32 regval;
|
||||
regval = getreg32(STM32_SDIO_MASK);
|
||||
regval &= ~bitset;
|
||||
putreg32(regval, STM32_SDIO_MASK);
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* SDIO Interface Methods
|
||||
****************************************************************************/
|
||||
/****************************************************************************
|
||||
* Name: stm32_reset
|
||||
*
|
||||
@ -300,7 +412,7 @@ static int stm32_attach(FAR struct sdio_dev_s *dev)
|
||||
*
|
||||
* Input Parameters:
|
||||
* dev - An instance of the MMC/SD device interface
|
||||
* cmd - The command to send
|
||||
* cmd - The command to send (32-bits, encoded)
|
||||
* arg - 32-bit argument required with some commands
|
||||
* data - A reference to data required with some commands
|
||||
*
|
||||
@ -309,9 +421,53 @@ static int stm32_attach(FAR struct sdio_dev_s *dev)
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
static void stm32_sendcmd(FAR struct sdio_dev_s *dev, ubyte cmd,
|
||||
static void stm32_sendcmd(FAR struct sdio_dev_s *dev, uint32 cmd,
|
||||
uint32 arg, FAR const ubyte *data)
|
||||
{
|
||||
uint32 regval;
|
||||
uint32 cmdidx = (cmd & MMCSD_CMDIDX_MASK) >> MMCSD_CMDIDX_SHIFT;
|
||||
|
||||
/* Set the SDIO Argument value */
|
||||
|
||||
putreg32(arg, STM32_SDIO_ARG);
|
||||
|
||||
/* Clear CMDINDEX, WAITRESP, WAITINT, WAITPEND, CPSMEN bits */
|
||||
|
||||
regval = getreg32(STM32_SDIO_CMD);
|
||||
regval &= ~(SDIO_CMD_CMDINDEX_MASK|SDIO_CMD_WAITRESP_MASK|
|
||||
SDIO_CMD_WAITINT|SDIO_CMD_WAITPEND|SDIO_CMD_CPSMEN);
|
||||
|
||||
/* Set WAITRESP bits */
|
||||
#warning VERIFY
|
||||
switch ((cmd & MMCSD_RESPONSE_MASK) >> MMCSD_RESPONSE_SHIFT)
|
||||
{
|
||||
case MMCSD_NO_RESPONSE:
|
||||
regval |= SDIO_CMD_NORESPONSE;
|
||||
break;
|
||||
|
||||
case MMCSD_R1_RESPONSE:
|
||||
case MMCSD_R1B_RESPONSE:
|
||||
case MMCSD_R3_RESPONSE:
|
||||
case MMCSD_R4_RESPONSE:
|
||||
case MMCSD_R5_RESPONSE:
|
||||
case MMCSD_R6_RESPONSE:
|
||||
case MMCSD_R7_RESPONSE:
|
||||
regval |= SDIO_CMD_SHORTRESPONSE;
|
||||
break;
|
||||
|
||||
case MMCSD_R2_RESPONSE:
|
||||
regval |= SDIO_CMD_LONGRESPONSE;
|
||||
break;
|
||||
}
|
||||
|
||||
/* Set CPSMEN and the command index */
|
||||
|
||||
cmdidx = (cmd & MMCSD_CMDIDX_MASK) >> MMCSD_CMDIDX_SHIFT;
|
||||
regval |= cmdidx | SDIO_CMD_CPSMEN;
|
||||
|
||||
/* Write the SDIO CMD */
|
||||
|
||||
putreg32(regval, STM32_SDIO_CMD);
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
@ -618,7 +774,17 @@ static int stm32_dmastop(FAR struct sdio_dev_s *dev)
|
||||
#ifdef CONFIG_SDIO_DMA
|
||||
static int stm32_dmastatus(FAR struct sdio_dev_s *dev, size_t *remaining)
|
||||
{
|
||||
return -ENOSYS;
|
||||
#ifdef CONFIG_DEBUG
|
||||
if (remaining)
|
||||
{
|
||||
*remaining = getreg32(STM32_SDIO_DCOUNT);
|
||||
return OK;
|
||||
}
|
||||
return -EINVAL;
|
||||
#else
|
||||
*remaining = getreg32(STM32_SDIO_DCOUNT);
|
||||
return OK;
|
||||
#endif
|
||||
}
|
||||
#endif
|
||||
|
||||
|
||||
@ -123,7 +123,7 @@
|
||||
#define SDIO_CMD_CMDINDEX_MASK (0x3f << SDIO_CMD_CMDINDEX_SHIFT)
|
||||
#define SDIO_CMD_WAITRESP_SHIFT (6) /* Bits 7-6: Wait for response bits */
|
||||
#define SDIO_CMD_WAITRESP_MASK (3 << SDIO_CMD_WAITRESP_SHIFT)
|
||||
# define SDIO_CMD_NORESPONSE1 (0 << SDIO_CMD_WAITRESP_SHIFT) /* 00/10: No response */
|
||||
# define SDIO_CMD_NORESPONSE (0 << SDIO_CMD_WAITRESP_SHIFT) /* 00/10: No response */
|
||||
# define SDIO_CMD_SHORTRESPONSE (1 << SDIO_CMD_WAITRESP_SHIFT) /* 01: Short response */
|
||||
# define SDIO_CMD_LONGRESPONSE (3 << SDIO_CMD_WAITRESP_SHIFT) /* 11: Long response */
|
||||
#define SDIO_CMD_WAITINT (1 << 8) /* Bit 8: CPSM waits for interrupt request */
|
||||
@ -217,6 +217,7 @@
|
||||
#define SDIO_ICR_CEATAENDC (1 << 23) /* Bit 23: CEATAEND flag clear bit */
|
||||
|
||||
#define SDIO_ICR_RESET 0x00c007ff
|
||||
#define SDIO_ICR_STATICFLAGS 0x000005ff
|
||||
|
||||
#define SDIO_MASK_CCRCFAILIE (1 << 0) /* Bit 0: Command CRC fail interrupt enable */
|
||||
#define SDIO_MASK_DCRCFAILIE (1 << 1) /* Bit 1: Data CRC fail interrupt enable */
|
||||
|
||||
@ -61,8 +61,8 @@
|
||||
#define MMCSD_CARDTYPE_UNKNOWN 0 /* Unknown card type */
|
||||
#define MMCSD_CARDTYPE_MMC 1 /* Bit 0: MMC card */
|
||||
#define MMCSD_CARDTYPE_SDV1 2 /* Bit 1: SD version 1.x */
|
||||
#define MMCSD_CARDTYPE_SDV2 4 /* Bit 1: SD version 2.x with byte addressing */
|
||||
#define MMCSD_CARDTYPE_BLOCK 8 /* Bit 2: SD version 2.x with block addressing */
|
||||
#define MMCSD_CARDTYPE_SDV2 4 /* Bit 2: SD version 2.x with byte addressing */
|
||||
#define MMCSD_CARDTYPE_BLOCK 8 /* Bit 3: SD version 2.x with block addressing */
|
||||
|
||||
#define IS_MMC(t) (((t) & MMCSD_CARDTYPE_MMC) != 0)
|
||||
#define IS_SD(t) (((t) & (MMCSD_CARDTYPE_SDV1|MMCSD_CARDTYPE_SDV2)) != 0)
|
||||
|
||||
71
drivers/mmcsd/mmcsd_sdio.h
Normal file
71
drivers/mmcsd/mmcsd_sdio.h
Normal file
@ -0,0 +1,71 @@
|
||||
/********************************************************************************************
|
||||
* drivers/mmcsd/mmcsd_sdio.h
|
||||
*
|
||||
* Copyright (C) 2009 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
********************************************************************************************/
|
||||
|
||||
#ifndef __DRIVERS_MMCSD_MMCSD_SDIO_H
|
||||
#define __DRIVERS_MMCSD_MMCSD_SDIO_H
|
||||
|
||||
/********************************************************************************************
|
||||
* Included Files
|
||||
********************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#include <sys/types.h>
|
||||
|
||||
/********************************************************************************************
|
||||
* Pre-Processor Definitions
|
||||
********************************************************************************************/
|
||||
|
||||
/********************************************************************************************
|
||||
* Public Types
|
||||
********************************************************************************************/
|
||||
|
||||
#undef EXTERN
|
||||
#if defined(__cplusplus)
|
||||
#define EXTERN extern "C"
|
||||
extern "C" {
|
||||
#else
|
||||
#define EXTERN extern
|
||||
#endif
|
||||
|
||||
/********************************************************************************************
|
||||
* Public Functions
|
||||
********************************************************************************************/
|
||||
|
||||
|
||||
#undef EXTERN
|
||||
#if defined(__cplusplus)
|
||||
}
|
||||
#endif
|
||||
#endif /* __DRIVERS_MMCSD_MMCSD_SDIO_H */
|
||||
@ -60,6 +60,213 @@
|
||||
|
||||
#define SDIOEVENT_ALLEVENTS 0xff
|
||||
|
||||
/* Commands are bit-encoded to provide as much information to the SDIO driver as
|
||||
* possible in 32-bits. The encoding is as follows:
|
||||
*
|
||||
* ---- ---- ---- ---- ---- --RR RRCC CCCC
|
||||
*
|
||||
* CCCCCC - Bits 0-5: 6-bit command index (Range 9-63)
|
||||
* RRRR - Bits 6-9: 4-bit response code (R1, R1B, R2-5)
|
||||
*/
|
||||
|
||||
/* MMC, SD, SDIO Common Indices */
|
||||
|
||||
#define MMCSD_CMDIDX_SHIFT (0)
|
||||
#define MMCSD_CMDIDX_MASK (0x3f << MMCSD_CMDIDX_SHIFT)
|
||||
# define MMCSD_CMDIDX0 0 /* GO_IDLE_STATE: Resets all cards to idle state
|
||||
* -Broadcast, no response */
|
||||
# define MMC_CMDIDX1 1 /* SEND_OP_COND: Sends capacity support information
|
||||
* -Broadcast, R3 response, 31:0=OCR */
|
||||
# define MMCSD_CMDIDX2 2 /* ALL_SEND_CID
|
||||
* -Broadcast, R2 response */
|
||||
# define MMC_CMDIDX3 3 /* SET_RELATIVE_ADDR
|
||||
* -Addressed Command, R1 response 31:16=RCA */
|
||||
# define SD_CMDIDX3 3 /* SEND_RELATIVE_ADDR
|
||||
* -Addressed Command, R6 response 31:16=RCA */
|
||||
# define MMCSD_CMDIDX4 4 /* SET_DSR
|
||||
* -Broadcast command, no response 31:16=RCA */
|
||||
# define SDIO_CMDIDX5 5 /* SDIO_SEND_OP_COND
|
||||
* -Addressed Command, R4 response 47:16=IO_OCR */
|
||||
# define MMCSD_CMDIDX6 6 /* HS_SWITCH: Checks switchable function */
|
||||
# define MMCSD_CMDIDX7 7 /* SELECT/DESELECT CARD
|
||||
* -Addressed Command, R1 response 31:16=RCA */
|
||||
# define SD_CMDIDX8 8 /* IF_COND: Sends SD Memory Card interface condition
|
||||
* R7 response */
|
||||
# define MMCSD_CMDIDX9 9 /* SEND_CSD: Asks card to send its card specific data (CSD)
|
||||
* -Addressed Command, R2 response 31:16=RCA */
|
||||
# define MMCSD_CMDIDX10 10 /* SEND_CID: Asks card to send its card identification (CID)
|
||||
* -Addressed Command, R2 response 31:16=RCA */
|
||||
# define MMC_CMDIDX11 11 /* READ_DAT_UNTIL_STOP
|
||||
* -Addressed data transfer command, R1 response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX12 12 /* STOP_TRANSMISSION: Forces the card to stop transmission
|
||||
* -Addressed Command, R1b response */
|
||||
# define MMCSD_CMDIDX13 13 /* SEND_STATUS: Asks card to send its status register
|
||||
* -Addressed Command, R1 response 31:16=RCA */
|
||||
# define MMCSD_CMDIDX14 14 /* HS_BUSTEST_READ: */
|
||||
# define MMCSD_CMDIDX15 15 /* GO_INACTIVE_STATE
|
||||
* Addressed Command, Response 31:16=RCA */
|
||||
# define MMCSD_CMDIDX16 16 /* SET_BLOCKLEN: Sets a block length (in bytes)
|
||||
* -Addressed Command, R1 response 31:0=BLEN */
|
||||
# define MMCSD_CMDIDX17 17 /* READ_SINGLE_BLOCK: Reads a block of the selected size
|
||||
* -Addressed data transfer command, R1 response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX18 18 /* READ_MULTIPLE_BLOCK: Continuously transfers blocks from card to host
|
||||
* -Addressed data transfer command, R1 response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX19 19 /* HS_BUSTEST_WRITE: */
|
||||
# define MMC_CMDIDX20 20 /* WRITE_DAT_UNTIL_STOP: (MMC)
|
||||
* -Addressed data transfer command, R1 response 31:0=DADR R1 */
|
||||
# define MMC_CMDIDX23 23 /* SET_BLOCK_COUNT: (MMC)
|
||||
* -Addressed data transfer command, R1 response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX24 24 /* WRITE_BLOCK: Writes a block of the selected size
|
||||
* -Addressed data transfer command, R1 response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX25 25 /* WRITE_MULTIPLE_BLOCK: Continuously writes blocks of data
|
||||
* -Addressed data transfer command, R1 response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX26 26 /* PROGRAM_CID: (Manufacturers only)
|
||||
* -Addressed data transfer command, R1 response */
|
||||
# define MMCSD_CMDIDX27 27 /* PROGRAM_CSD: Set programmable bits of the CSD
|
||||
* -Addressed data transfer command, R1 response */
|
||||
# define MMCSD_CMDIDX28 28 /* SET_WRITE_PROT: Sets the write protection bit of group
|
||||
* -Addressed Command, R1b response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX29 29 /* CLR_WRITE_PROT: Clears the write protection bit of group
|
||||
* -Addressed Command, R1b response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX30 30 /* SEND_WRITE_PROT: Asks card to send state of write protection bits
|
||||
* -Addressed data transfer command, R1 response 31:0=WADR */
|
||||
# define SD_CMDIDX32 32 /* ERASE_GRP_START: Sets address of first block to erase (SD)
|
||||
* -Addressed Command, R1 response 31:0=DADR */
|
||||
# define SD_CMDIDX33 33 /* ERASE_GRP_END: Sets address of last block to erase (SD)
|
||||
* -Addressed Command, R1 response 31:0=DADR */
|
||||
# define MMC_CMDIDX34 34 /* UNTAG_SECTOR: (MMC)
|
||||
* -Addressed Command, R1 response 31:0=DADR */
|
||||
# define MMC_CMDIDX35 35 /* TAG_ERASE_GROUP_START: Sets address of first block to erase (MMC)
|
||||
* -Addressed Command, R1 response 31:0=DADR */
|
||||
# define MMC_CMDIDX36 36 /* TAG_ERASE_GROUP_END: Sets address of last block to erase (MMC)
|
||||
* -Addressed Command, R1 response 31:0=DADR */
|
||||
# define MMC_CMDIDX37 37 /* UNTAG_ERASE_GROUP: (MMC)
|
||||
* -Addressed Command, R1 response 31:0=DADR */
|
||||
# define MMCSD_CMDIDX38 38 /* ERASE: Erases all previously selected write blocks
|
||||
* -Addressed Command, R1b response */
|
||||
# define MMC_CMDIDX39 39 /* FAST_IO: (MMC)
|
||||
* -Addressed Command, R4 response (Complex) */
|
||||
# define MMC_CMDIDX40 40 /* GO_IRQ_STATE: (MMC)
|
||||
* -Broadcast command, R5 response */
|
||||
# define MMCSD_CMDIDX42 42 /* LOCK_UNLOCK: Used to Set/Reset the Password or lock/unlock card
|
||||
* -Addressed data transfer command, R1b response */
|
||||
# define SD_CMDIDX55 55 /* APP_CMD: Tells card that the next command is an application specific command
|
||||
* - Addressed Command, R1 response 31:16=RCA */
|
||||
# define MMCSD_CMDIDX56 56 /* GEN_CMD: Used transfer a block to or get block from card
|
||||
* -Addressed data transfer command, R1 Response */
|
||||
|
||||
/* SD/SDIO APP commands (must be preceded by CMD55) */
|
||||
|
||||
# define SD_ACMDIDX6 6 /* SET_BUS_WIDTH:
|
||||
* -Addressed Command, R1 response 1:0=BUSW */
|
||||
# define SD_ACMDIDX13 13 /* SD_STATUS: Send the SD Status
|
||||
* -Addressed data transfer command, R1 response */
|
||||
# define SD_ACMDIDX18 18 /* SECURE_READ_MULTIPLE_BLOCK: */
|
||||
# define SD_ACMDIDX22 22 /* SEND_NUM_WR_BLOCKS: Send number of the errorfree blocks
|
||||
* -Addressed data transfer command, R1 response */
|
||||
# define SD_ACMDIDX23 23 /* SET_WR_BLK_ERASE_COUNT: Set number blocks to erase before writing
|
||||
* -Addressed Command, R1 response 22:0=NBLK */
|
||||
# define SD_ACMDIDX25 25 /* SECURE_WRITE_MULTIPLE_BLOCK: */
|
||||
# define SD_ACMDIDX38 38 /* SECURE_ERASE: */
|
||||
# define SD_ACMDIDX41 41 /* SD_SEND_OP_COND: Sends host capacity support information
|
||||
* -Broadcast command, R3 response 31:0=OCR */
|
||||
# define SD_ACMDIDX42 42 /* SET_CLR_CARD_DETECT: Connect/disconnect pull-up resistor on CS
|
||||
* Addressed Command, R1 response 0:0=CD */
|
||||
# define SD_ACMDIDX43 43 /* GET_MKB: */
|
||||
# define SD_ACMDIDX44 44 /* GET_MID: */
|
||||
# define SD_ACMDIDX45 45 /* SET_CER_RN1: */
|
||||
# define SD_ACMDIDX46 46 /* GET_CER_RN2: */
|
||||
# define SD_ACMDIDX47 47 /* SET_CER_RES2: */
|
||||
# define SD_ACMDIDX48 48 /* GET_CER_RES1/WRITE_MKB: */
|
||||
# define SD_ACMDIDX49 49 /* CHANGE_SECURE_AREA: */
|
||||
# define SD_ACMDIDX51 51 /* SEND_SCR: Reads the SD Configuration Register (SCR)
|
||||
* Addressed data transfer command, R1 response */
|
||||
# define SDIO_ACMDIDX52 52 /* IO_RW_DIRECT: (SDIO only)
|
||||
* -R5 response, 23:16=status 15:8=data */
|
||||
# define SDIO_ACMDIDX53 53 /* IO_RW_EXTENDED: (SDIO only)
|
||||
* -R5 response, 23:16=status */
|
||||
|
||||
/* Response Encodings */
|
||||
|
||||
#define MMCSD_RESPONSE_SHIFT (6)
|
||||
#define MMCSD_RESPONSE_MASK (15 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_NO_RESPONSE (0 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_R1_RESPONSE (1 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_R1B_RESPONSE (2 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_R2_RESPONSE (3 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_R3_RESPONSE (4 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_R4_RESPONSE (5 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_R5_RESPONSE (6 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_R6_RESPONSE (7 << MMCSD_RESPONSE_SHIFT)
|
||||
# define MMCSD_R7_RESPONSE (8 << MMCSD_RESPONSE_SHIFT)
|
||||
|
||||
/* Fully decorated MMC, SD, SDIO commands */
|
||||
|
||||
#define MMCSD_CMD0 (MMCSD_CMDIDX0 |MMCSD_NO_RESPONSE)
|
||||
#define MMC_CMD1 (MMC_CMDIDX1 |MMCSD_R3_RESPONSE)
|
||||
#define MMCSD_CMD2 (MMCSD_CMDIDX2 |MMCSD_R2_RESPONSE)
|
||||
#define MMC_CMD3 (MMC_CMDIDX3 |MMCSD_R1_RESPONSE)
|
||||
#define SD_CMD3 (SD_CMDIDX3 |MMCSD_R6_RESPONSE)
|
||||
#define MMCSD_CMD4 (MMCSD_CMDIDX4 |MMCSD_NO_RESPONSE)
|
||||
#define SDIO_CMD5 (SDIO_CMDIDX5 |MMCSD_R4_RESPONSE)
|
||||
#define MMCSD_CMD6 (MMCSD_CMDIDX6 |MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD7S (MMCSD_CMDIDX7 |MMCSD_R1B_RESPONSE)
|
||||
#define MMCSD_CMD7D (MMCSD_CMDIDX7 |MMCSD_NO_RESPONSE) /* No response when de-selecting card */
|
||||
#define SD_CMD8 (SD_CMDIDX8 |MMCSD_R7_RESPONSE)
|
||||
#define MMCSD_CMD9 (MMCSD_CMDIDX9 |MMCSD_R2_RESPONSE)
|
||||
#define MMCSD_CMD10 (MMCSD_CMDIDX10|MMCSD_R2_RESPONSE)
|
||||
#define MMC_CMD11 (MMC_CMDIDX11 |MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD12 (MMCSD_CMDIDX12|MMCSD_R1B_RESPONSE)
|
||||
#define MMCSD_CMD13 (MMCSD_CMDIDX13|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD14 (MMCSD_CMDIDX14|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD15 (MMCSD_CMDIDX15|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD16 (MMCSD_CMDIDX16|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD17 (MMCSD_CMDIDX17|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD18 (MMCSD_CMDIDX18|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD19 (MMCSD_CMDIDX19|MMCSD_R1_RESPONSE)
|
||||
#define MMC_CMD23 (MMC_CMDIDX23 |MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD24 (MMCSD_CMDIDX24|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD25 (MMCSD_CMDIDX25|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD26 (MMCSD_CMDIDX26|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD27 (MMCSD_CMDIDX27|MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD28 (MMCSD_CMDIDX28|MMCSD_R1B_RESPONSE)
|
||||
#define MMCSD_CMD29 (MMCSD_CMDIDX29|MMCSD_R1B_RESPONSE)
|
||||
#define MMCSD_CMD30 (MMCSD_CMDIDX30|MMCSD_R1_RESPONSE)
|
||||
#define SD_CMD32 (SD_CMDIDX32 |MMCSD_R1_RESPONSE)
|
||||
#define SD_CMD33 (SD_CMDIDX33 |MMCSD_R1_RESPONSE)
|
||||
#define MMC_CMD34 (MMC_CMDIDX34 |MMCSD_R1_RESPONSE)
|
||||
#define MMC_CMD35 (MMC_CMDIDX35 |MMCSD_R1_RESPONSE)
|
||||
#define MMC_CMD36 (MMC_CMDIDX36 |MMCSD_R1_RESPONSE)
|
||||
#define MMC_CMD37 (MMC_CMDIDX37 |MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD38 (MMCSD_CMDIDX38|MMCSD_R1B_RESPONSE)
|
||||
#define MMC_CMD39 (MMC_CMDIDX39 |MMCSD_R4_RESPONSE)
|
||||
#define MMC_CMD40 (MMC_CMDIDX40 |MMCSD_R5_RESPONSE)
|
||||
#define MMCSD_CMD42 (MMCSD_CMDIDX42|MMCSD_R1B_RESPONSE)
|
||||
#define SD_CMD55 (SD_CMDIDX55 |MMCSD_R1_RESPONSE)
|
||||
#define MMCSD_CMD56 (MMCSD_CMDIDX56|MMCSD_R1_RESPONSE)
|
||||
|
||||
/* SD/SDIO APP commands (must be preceded by CMD55) */
|
||||
|
||||
#define SD_ACMD6 (SD_ACMDIDX6 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD13 (SD_ACMDIDX13 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD18 (SD_ACMDIDX18 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD22 (SD_ACMDIDX22 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD23 (SD_ACMDIDX23 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD25 (SD_ACMDIDX25 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD38 (SD_ACMDIDX38 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD41 (SD_ACMDIDX41 |MMCSD_R3_RESPONSE)
|
||||
#define SD_ACMD42 (SD_ACMDIDX42 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD43 (SD_ACMDIDX43 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD44 (SD_ACMDIDX44 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD45 (SD_ACMDIDX45 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD46 (SD_ACMDIDX46 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD47 (SD_ACMDIDX47 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD48 (SD_ACMDIDX48 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD49 (SD_ACMDIDX49 |MMCSD_R1_RESPONSE)
|
||||
#define SD_ACMD51 (SD_ACMDIDX51 |MMCSD_R1_RESPONSE)
|
||||
#define SDIO_ACMD52 (SDIO_ACMDIDX52|MMCSD_R5_RESPONSE)
|
||||
#define SDIO_ACMD53 (SDIO_ACMDIDX53|MMCSD_R5_RESPONSE)
|
||||
|
||||
/****************************************************************************
|
||||
* Name: SDIO_RESET
|
||||
*
|
||||
@ -179,7 +386,7 @@
|
||||
*
|
||||
* Input Parameters:
|
||||
* dev - An instance of the MMC/SD device interface
|
||||
* cmd - The command to send
|
||||
* cmd - The command to send. See 32-bit command definitions above.
|
||||
* arg - 32-bit argument required with some commands
|
||||
* data - A reference to data required with some commands
|
||||
*
|
||||
@ -494,7 +701,7 @@ struct sdio_dev_s
|
||||
|
||||
/* Command/Status/Data Transfer */
|
||||
|
||||
void (*sendcmd)(FAR struct sdio_dev_s *dev, ubyte cmd, uint32 arg, FAR const ubyte *data);
|
||||
void (*sendcmd)(FAR struct sdio_dev_s *dev, uint32 cmd, uint32 arg, FAR const ubyte *data);
|
||||
int (*senddata)(FAR struct sdio_dev_s *dev, FAR const ubyte *buffer);
|
||||
|
||||
int (*recvR1)(FAR struct sdio_dev_s *dev, uint16 buffer[3]);
|
||||
|
||||
Loading…
Reference in New Issue
Block a user