diff --git a/arch/arm/src/lpc43xx/Kconfig b/arch/arm/src/lpc43xx/Kconfig index 1491120fbe..808c895544 100644 --- a/arch/arm/src/lpc43xx/Kconfig +++ b/arch/arm/src/lpc43xx/Kconfig @@ -163,6 +163,151 @@ config LPC43_ETHERNET bool "Ethernet" default n +if LPC43_ETHERNET +menu "Ethernet MAC configuration" + +config LPC43_PHYADDR + int "PHY address" + default 1 + ---help--- + The 5-bit address of the PHY on the board. Default: 1 + +config LPC43_PHYINIT + bool "Board-specific PHY Initialization" + default n + ---help--- + Some boards require specialized initialization of the PHY before it can be used. + This may include such things as configuring GPIOs, resetting the PHY, etc. If + LPC43_PHYINIT is defined in the configuration then the board specific logic must + provide lpc43_phyinitialize(); The LPC43 Ethernet driver will call this function + one time before it first uses the PHY. + +config LPC43_MII + bool "Use MII interface" + default n + ---help--- + Support Ethernet MII interface. + +config LPC43_AUTONEG + bool "Use autonegotiation" + default y + ---help--- + Use PHY autonegotiation to determine speed and mode + +config LPC43_ETHFD + bool "Full duplex" + default n + depends on !LPC43_AUTONEG + ---help--- + If LPC43_AUTONEG is not defined, then this may be defined to select full duplex + mode. Default: half-duplex + +config LPC43_ETH100MBPS + bool "100 Mbps" + default n + depends on !LPC43_AUTONEG + ---help--- + If LPC43_AUTONEG is not defined, then this may be defined to select 100 MBps + speed. Default: 10 Mbps + +config LPC43_PHYSR + int "PHY Status Register Address (decimal)" + depends on LPC43_AUTONEG + ---help--- + This must be provided if LPC43_AUTONEG is defined. The PHY status register + address may diff from PHY to PHY. This configuration sets the address of + the PHY status register. + +config LPC43_PHYSR_ALTCONFIG + bool "PHY Status Alternate Bit Layout" + default n + depends on LPC43_AUTONEG + ---help--- + Different PHYs present speed and mode information in different ways. Some + will present separate information for speed and mode (this is the default). + Those PHYs, for example, may provide a 10/100 Mbps indication and a separate + full/half duplex indication. This options selects an alternative representation + where speed and mode information are combined. This might mean, for example, + separate bits for 10HD, 100HD, 10FD and 100FD. + +config LPC43_PHYSR_SPEED + hex "PHY Speed Mask" + depends on LPC43_AUTONEG && !LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This provides bit mask + for isolating the 10 or 100MBps speed indication. + +config LPC43_PHYSR_100MBPS + hex "PHY 100Mbps Speed Value" + depends on LPC43_AUTONEG && !LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This provides the value + of the speed bit(s) indicating 100MBps speed. + +config LPC43_PHYSR_MODE + hex "PHY Mode Mask" + depends on LPC43_AUTONEG && !LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This provide bit mask + for isolating the full or half duplex mode bits. + +config LPC43_PHYSR_FULLDUPLEX + hex "PHY Full Duplex Mode Value" + depends on LPC43_AUTONEG && !LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This provides the + value of the mode bits indicating full duplex mode. + +config LPC43_PHYSR_ALTMODE + hex "PHY Mode Mask" + depends on LPC43_AUTONEG && LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This provide bit mask + for isolating the speed and full/half duplex mode bits. + +config LPC43_PHYSR_10HD + hex "10MBase-T Half Duplex Value" + depends on LPC43_AUTONEG && LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This is the value + under the bit mask that represents the 10Mbps, half duplex setting. + +config LPC43_PHYSR_100HD + hex "100Base-T Half Duplex Value" + depends on LPC43_AUTONEG && LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This is the value + under the bit mask that represents the 100Mbps, half duplex setting. + +config LPC43_PHYSR_10FD + hex "10Base-T Full Duplex Value" + depends on LPC43_AUTONEG && LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This is the value + under the bit mask that represents the 10Mbps, full duplex setting. + +config LPC43_PHYSR_100FD + hex "100Base-T Full Duplex Value" + depends on LPC43_AUTONEG && LPC43_PHYSR_ALTCONFIG + ---help--- + This must be provided if LPC43_AUTONEG is defined. This is the value + under the bit mask that represents the 100Mbps, full duplex setting. + +config LPC43_RMII + bool + default y if !LPC43_MII + + +config LPC43_ETHERNET_REGDEBUG + bool "Register-Level Debug" + default n + depends on DEBUG + ---help--- + Enable very low-level register access debug. Depends on DEBUG. + +endmenu +endif + config LPC43_EVNTMNTR bool "Event Monitor" default n diff --git a/arch/arm/src/lpc43xx/Make.defs b/arch/arm/src/lpc43xx/Make.defs index 6e0d907e66..b15004c54d 100644 --- a/arch/arm/src/lpc43xx/Make.defs +++ b/arch/arm/src/lpc43xx/Make.defs @@ -118,6 +118,10 @@ ifeq ($(CONFIG_GPIO_IRQ),y) CHIP_CSRCS += lpc43_gpioint.c endif +ifeq ($(CONFIG_LPC43_ETHERNET),y) +CHIP_CSRCS += lpc43_ethernet.c +endif + ifeq ($(CONFIG_LPC43_SPI),y) CHIP_CSRCS += lpc43_spi.c endif diff --git a/arch/arm/src/lpc43xx/chip/lpc43_ethernet.h b/arch/arm/src/lpc43xx/chip/lpc43_ethernet.h index c2db11db88..6da125a6fe 100644 --- a/arch/arm/src/lpc43xx/chip/lpc43_ethernet.h +++ b/arch/arm/src/lpc43xx/chip/lpc43_ethernet.h @@ -181,7 +181,8 @@ /* MAC frame filter register */ #define ETH_MACFFLT_PR (1 << 0) /* Bit 0: Promiscuous mode */ - /* Bits 1-2: Reserved */ +#define ETH_MACFFLT_HUC (1 << 1) /* Bit 1: Hash Unicast */ +#define ETH_MACFFLT_HMC (1 << 2) /* Bit 2: Hash Multicast */ #define ETH_MACFFLT_DAIF (1 << 3) /* Bit 3: Destination address inverse filtering */ #define ETH_MACFFLT_PM (1 << 4) /* Bit 4: Pass all multicast */ #define ETH_MACFFLT_DBF (1 << 5) /* Bit 5: Disable Broadcast Frames */ @@ -191,9 +192,9 @@ # define ETH_MACFFLT_PCF_PAUSE (1 << ETH_MACFFLT_PCF_SHIFT) /* Prevents all except Pause control frames */ # define ETH_MACFFLT_PCF_ALL (2 << ETH_MACFFLT_PCF_SHIFT) /* Forwards all control frames */ # define ETH_MACFFLT_PCF_FILTER (3 << ETH_MACFFLT_PCF_SHIFT) /* Forwards all that pass address filter */ -#define ETH_MACFFLT_SAIF (1 << 8) /* Bit 8: Source address inverse filtering */ -#define ETH_MACFFLT_SAF (1 << 9) /* Bit 9: Source address filter */ - /* Bits 10-30: Reserved */ + /* Bit 8-9: Reserved */ +#define ETH_MACFFLT_HPF (1 << 10) /* Bit 10: Hash or perfect filter */ + /* Bits 11-30: Reserved */ #define ETH_MACFFLT_RA (1 << 31) /* Bit 31: Receive all */ /* MAC hash table high/low register (32-bit values) */ @@ -208,7 +209,7 @@ # define ETH_MACMIIA_CR_100_150 (1 << ETH_MACMIIA_CR_SHIFT) /* 100-150 MHz CLK_M4_ETHERNET/62 */ # define ETH_MACMIIA_CR_20_35 (2 << ETH_MACMIIA_CR_SHIFT) /* 20-35 MHz CLK_M4_ETHERNET/16 */ # define ETH_MACMIIA_CR_35_60 (3 << ETH_MACMIIA_CR_SHIFT) /* 35-60 MHz CLK_M4_ETHERNET/26 */ -# define ETH_MACMIIA_CR_150_168 (4 << ETH_MACMIIA_CR_SHIFT) /* 150-168 MHz CLK_M4_ETHERNET/102 */ +# define ETH_MACMIIA_CR_150_250 (4 << ETH_MACMIIA_CR_SHIFT) /* 150-250 MHz CLK_M4_ETHERNET/102 */ # define ETH_MACMIIA_CR_250_300 (5 << ETH_MACMIIA_CR_SHIFT) /* 250-300 MHz CLK_M4_ETHERNET/124 */ # define ETH_MACMIIA_CR_DIV42 (8 << ETH_MACMIIA_CR_SHIFT) /* 60-100 MHz CLK_M4_ETHERNET/42 */ # define ETH_MACMIIA_CR_DIV62 (9 << ETH_MACMIIA_CR_SHIFT) /* 100-150 MHz CLK_M4_ETHERNET/62 */ @@ -314,7 +315,7 @@ /* Bits 4-8: Reserved */ #define ETH_MACIM_TSIM (1 << 9) /* Bit 9: Time stamp interrupt mask */ /* Bits 10-31: Reserved */ -#define ETH_MACIM_ALLINTS (ETH_MACIM_PMTIM|ETH_MACIM_TSTIM) +#define ETH_MACIM_ALLINTS (ETH_MACIM_PMTIM|ETH_MACIM_TSIM) /* MAC address 0 high register */ @@ -499,9 +500,9 @@ #define ETH_TDES0_CC_MASK (15 << ETH_TDES0_CC_SHIFT) #define ETH_TDES0_VF (1 << 7) /* Bit 7: VLAN frame */ #define ETH_TDES0_EC (1 << 8) /* Bit 8: Excessive collision */ -#define ETH_TDES0_LC (1 << 9) /* Bit 9: Late collision */ +#define ETH_TDES0_LCL (1 << 9) /* Bit 9: Late collision */ #define ETH_TDES0_NC (1 << 10) /* Bit 10: No carrier */ -#define ETH_TDES0_LC (1 << 11) /* Bit 11: Loss of carrier */ +#define ETH_TDES0_LCR (1 << 11) /* Bit 11: Loss of carrier */ #define ETH_TDES0_IPE (1 << 12) /* Bit 12: IP payload error */ #define ETH_TDES0_FF (1 << 13) /* Bit 13: Frame flushed */ #define ETH_TDES0_JT (1 << 14) /* Bit 14: Jabber timeout */ @@ -536,7 +537,7 @@ #define ETH_RDES0_ESA (1 << 0) /* Bit 0: Extended status available */ #define ETH_RDES0_CE (1 << 1) /* Bit 1: CRC error */ -#define ETH_RDES0_DE (1 << 2) /* Bit 2: Dribble bit error */ +#define ETH_RDES0_DRE (1 << 2) /* Bit 2: Dribble bit error */ #define ETH_RDES0_RE (1 << 3) /* Bit 3: Receive error */ #define ETH_RDES0_RWT (1 << 4) /* Bit 4: Receive watchdog timeout */ #define ETH_RDES0_FT (1 << 5) /* Bit 5: Frame type */ @@ -548,7 +549,7 @@ #define ETH_RDES0_OE (1 << 11) /* Bit 11: Overflow error */ #define ETH_RDES0_LE (1 << 12) /* Bit 12: Length error */ #define ETH_RDES0_SAF (1 << 13) /* Bit 13: Source address filter fail */ -#define ETH_RDES0_DE (1 << 14) /* Bit 14: Descriptor error */ +#define ETH_RDES0_DS (1 << 14) /* Bit 14: Descriptor error */ #define ETH_RDES0_ES (1 << 15) /* Bit 15: Error summary */ #define ETH_RDES0_FL_SHIFT (16) /* Bits 16-29: Frame length */ #define ETH_RDES0_FL_MASK (0x3fff << ETH_RDES0_FL_SHIFT) @@ -584,12 +585,12 @@ * transparent clock) */ # define ETH_RDES4_MT_PDELREQMM (6 << ETH_RDES4_MT_SHIFT) /* Pdelay_Resp (in peer-to-peer * transparent clock) */ -# define ETH_RDES4_MT_PDELREQFUS (7 << ETH_RDES4_MT_SHIFT) /* Pdelay_Resp_Follow_Up (in +# define ETH_RDES4_MT_PDELRESFUS (7 << ETH_RDES4_MT_SHIFT) /* Pdelay_Resp_Follow_Up (in * peer-to-peer transparent clock) */ -# define ETH_RDES4_MT_PDELREQFUS (8 << ETH_RDES4_MT_SHIFT) /* Announce */ -# define ETH_RDES4_MT_PDELREQFUS (9 << ETH_RDES4_MT_SHIFT) /* Management */ -# define ETH_RDES4_MT_PDELREQFUS (10 << ETH_RDES4_MT_SHIFT) /* Signaling */ -# define ETH_RDES4_MT_PDELREQFUS (15 << ETH_RDES4_MT_SHIFT) /* PTP packet with Reserved message type */ +# define ETH_RDES4_MT_ANNOUNCE (8 << ETH_RDES4_MT_SHIFT) /* Announce */ +# define ETH_RDES4_MT_MANAGEMENT (9 << ETH_RDES4_MT_SHIFT) /* Management */ +# define ETH_RDES4_MT_SIGNALING (10 << ETH_RDES4_MT_SHIFT) /* Signaling */ +# define ETH_RDES4_MT_PTP (15 << ETH_RDES4_MT_SHIFT) /* PTP packet with Reserved message type */ #define ETH_RDES4_PTPTYPE (1 << 12) /* Bit 12: PTP frame type */ #define ETH_RDES4_PTPVERSION (1 << 13) /* Bit 13: PTP version */ /* Bits 14-31: Reserved */ @@ -662,6 +663,5 @@ extern "C" #endif #endif /* __ASSEMBLY__ */ -#endif /* LPC43_NETHERNET > 0 */ #endif /* __ARCH_ARM_SRC_LPC43XX_CHIP_LPC43_ETHERNET_H */ diff --git a/arch/arm/src/lpc43xx/lpc43_ethernet.c b/arch/arm/src/lpc43xx/lpc43_ethernet.c new file mode 100644 index 0000000000..8b0b2b6c24 --- /dev/null +++ b/arch/arm/src/lpc43xx/lpc43_ethernet.c @@ -0,0 +1,4008 @@ +/**************************************************************************** + * arch/arm/src/lpc43/lpc43_eth.c + * + * Copyright (C) 2011-2015 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include +#if defined(CONFIG_NET) && defined(CONFIG_LPC43_ETHERNET) + +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include +#include + +#ifdef CONFIG_NET_NOINTS +# include +#endif + +#include +#include +#include +#if defined(CONFIG_NET_PKT) +# include +#endif + +#include "up_internal.h" + +#include "chip.h" +#include "lpc43_pinconfig.h" +#include "lpc43_ethernet.h" +#include "chip/lpc43_creg.h" +#include "chip/lpc43_cgu.h" +#include "lpc43_rgu.h" +#include "up_arch.h" +#include + +/**************************************************************************** + * Pre-processor Definitions + ****************************************************************************/ +/* Configuration ************************************************************/ + +/* If processing is not done at the interrupt level, then high priority + * work queue support is required. + */ + +#if defined(CONFIG_NET_NOINTS) && !defined(CONFIG_SCHED_HPWORK) +# error High priority work queue support is required +#endif + +#ifndef CONFIG_LPC43_PHYADDR +# error "CONFIG_LPC43_PHYADDR must be defined in the NuttX configuration" +#endif + +#if !defined(CONFIG_LPC43_MII) && !defined(CONFIG_LPC43_RMII) +# warning "Neither CONFIG_LPC43_MII nor CONFIG_LPC43_RMII defined" +#endif + +#if defined(CONFIG_LPC43_MII) && defined(CONFIG_LPC43_RMII) +# error "Both CONFIG_LPC43_MII and CONFIG_LPC43_RMII defined" +#endif + +#ifdef CONFIG_LPC43_AUTONEG +# ifndef CONFIG_LPC43_PHYSR +# error "CONFIG_LPC43_PHYSR must be defined in the NuttX configuration" +# endif +# ifdef CONFIG_LPC43_PHYSR_ALTCONFIG +# ifndef CONFIG_LPC43_PHYSR_ALTMODE +# error "CONFIG_LPC43_PHYSR_ALTMODE must be defined in the NuttX configuration" +# endif +# ifndef CONFIG_LPC43_PHYSR_10HD +# error "CONFIG_LPC43_PHYSR_10HD must be defined in the NuttX configuration" +# endif +# ifndef CONFIG_LPC43_PHYSR_100HD +# error "CONFIG_LPC43_PHYSR_100HD must be defined in the NuttX configuration" +# endif +# ifndef CONFIG_LPC43_PHYSR_10FD +# error "CONFIG_LPC43_PHYSR_10FD must be defined in the NuttX configuration" +# endif +# ifndef CONFIG_LPC43_PHYSR_100FD +# error "CONFIG_LPC43_PHYSR_100FD must be defined in the NuttX configuration" +# endif +# else +# ifndef CONFIG_LPC43_PHYSR_SPEED +# error "CONFIG_LPC43_PHYSR_SPEED must be defined in the NuttX configuration" +# endif +# ifndef CONFIG_LPC43_PHYSR_100MBPS +# error "CONFIG_LPC43_PHYSR_100MBPS must be defined in the NuttX configuration" +# endif +# ifndef CONFIG_LPC43_PHYSR_MODE +# error "CONFIG_LPC43_PHYSR_MODE must be defined in the NuttX configuration" +# endif +# ifndef CONFIG_LPC43_PHYSR_FULLDUPLEX +# error "CONFIG_LPC43_PHYSR_FULLDUPLEX must be defined in the NuttX configuration" +# endif +# endif +#endif + +#ifdef CONFIG_LPC43_ETH_PTP +# warning "CONFIG_LPC43_ETH_PTP is not yet supported" +#endif + +/* This driver does not use enhanced descriptors. Enhanced descriptors must + * be used, however, if time stamping or and/or IPv4 checksum offload is + * supported. + */ + +#undef CONFIG_LPC43_ETH_ENHANCEDDESC +#undef CONFIG_LPC43_ETH_HWCHECKSUM + +/* Ethernet buffer sizes, number of buffers, and number of descriptors */ + +#ifndef CONFIG_NET_MULTIBUFFER +# error "CONFIG_NET_MULTIBUFFER is required" +#endif + +/* Add 4 to the configured buffer size to account for the 2 byte checksum + * memory needed at the end of the maximum size packet. Buffer sizes must + * be an even multiple of 4, 8, or 16 bytes (depending on buswidth). We + * will use the 16-byte alignment in all cases. + */ + +#define OPTIMAL_ETH_BUFSIZE ((CONFIG_NET_ETH_MTU + 4 + 15) & ~15) + +#ifndef CONFIG_LPC43_ETH_BUFSIZE +# define CONFIG_LPC43_ETH_BUFSIZE OPTIMAL_ETH_BUFSIZE +#endif + +#if CONFIG_LPC43_ETH_BUFSIZE > ETH_TDES1_TBS1_MASK +# error "CONFIG_LPC43_ETH_BUFSIZE is too large" +#endif + +#if (CONFIG_LPC43_ETH_BUFSIZE & 15) != 0 +# error "CONFIG_LPC43_ETH_BUFSIZE must be aligned" +#endif + +#if CONFIG_LPC43_ETH_BUFSIZE != OPTIMAL_ETH_BUFSIZE +# warning "You using an incomplete/untested configuration" +#endif + +#ifndef CONFIG_LPC43_ETH_NRXDESC +# define CONFIG_LPC43_ETH_NRXDESC 8 +#endif +#ifndef CONFIG_LPC43_ETH_NTXDESC +# define CONFIG_LPC43_ETH_NTXDESC 4 +#endif + +/* We need at least one more free buffer than transmit buffers */ + +#define LPC43_ETH_NFREEBUFFERS (CONFIG_LPC43_ETH_NTXDESC+1) + +/* Extremely detailed register debug that you would normally never want + * enabled. + */ + +#ifndef CONFIG_DEBUG +# undef CONFIG_LPC43_ETHMAC_REGDEBUG +#endif + +/* Clocking *****************************************************************/ +/* Set MACMIIAR CR bits depending on HCLK setting */ + +#if BOARD_FCLKOUT_FREQUENCY >= 20000000 && BOARD_FCLKOUT_FREQUENCY < 35000000 +# define ETH_MACMIIA_CR ETH_MACMIIA_CR_20_35 +#elif BOARD_FCLKOUT_FREQUENCY >= 35000000 && BOARD_FCLKOUT_FREQUENCY < 60000000 +# define ETH_MACMIIA_CR ETH_MACMIIA_CR_35_60 +#elif BOARD_FCLKOUT_FREQUENCY >= 60000000 && BOARD_FCLKOUT_FREQUENCY < 100000000 +# define ETH_MACMIIA_CR ETH_MACMIIA_CR_60_100 +#elif BOARD_FCLKOUT_FREQUENCY >= 100000000 && BOARD_FCLKOUT_FREQUENCY < 150000000 +# define ETH_MACMIIA_CR ETH_MACMIIA_CR_100_150 +#elif BOARD_FCLKOUT_FREQUENCY >= 150000000 && BOARD_FCLKOUT_FREQUENCY <= 250000000 +# define ETH_MACMIIA_CR ETH_MACMIIA_CR_150_250 +#elif BOARD_FCLKOUT_FREQUENCY >= 250000000 && BOARD_FCLKOUT_FREQUENCY <= 350000000 +# define ETH_MACMIIA_CR ETH_MACMIIA_CR_250_300 +#else +# error "BOARD_FCLKOUT_FREQUENCY not supportable" +#endif + +/* Timing *******************************************************************/ +/* TX poll delay = 1 seconds. CLK_TCK is the number of clock ticks per + * second + */ + +#define LPC43_WDDELAY (1*CLK_TCK) +#define LPC43_POLLHSEC (1*2) + +/* TX timeout = 1 minute */ + +#define LPC43_TXTIMEOUT (60*CLK_TCK) + +/* PHY reset/configuration delays in milliseconds */ + +#define PHY_RESET_DELAY (65) +#define PHY_CONFIG_DELAY (1000) + +/* PHY read/write delays in loop counts */ + +#define PHY_READ_TIMEOUT (0x0004ffff) +#define PHY_WRITE_TIMEOUT (0x0004ffff) +#define PHY_RETRY_TIMEOUT (0x0004ffff) + +/* Register values **********************************************************/ + +/* Clear the MACCR bits that will be setup during MAC initialization (or that + * are cleared unconditionally). Per the reference manual, all reserved bits + * must be retained at their reset value. + * + * ETH_MACCFG_RE Bit 2: Receiver enable + * ETH_MACCFG_TE Bit 3: Transmitter enable + * ETH_MACCFG_DC Bit 4: Deferral check + * ETH_MACCFG_BL Bits 5-6: Back-off limit + * ETH_MACCFG_APCS Bit 7: Automatic pad/CRC stripping + * ETH_MACCFG_RD Bit 9: Retry disable + * ETH_MACCFG_DM Bit 11: Duplex mode + * ETH_MACCFG_LM Bit 12: Loopback mode + * ETH_MACCFG_DO Bit 13: Receive own disable + * ETH_MACCFG_FES Bit 14: Fast Ethernet speed + * ETH_MACCFG_CSD Bit 16: Carrier sense disable + * ETH_MACCFG_IFG Bits 17-19: Interframe gap + * ETH_MACCFG_JD Bit 22: Jabber disable + * ETH_MACCFG_WD Bit 23: Watchdog disable + * ETH_MACCFG_CSTF Bits 25: CRC stripping for Type frames (F2/F4 only) + */ + +#define MACCR_CLEAR_BITS \ + (ETH_MACCFG_RE | ETH_MACCFG_TE | ETH_MACCFG_DF | ETH_MACCFG_BL_MASK | \ + ETH_MACCFG_ACS | ETH_MACCFG_RD | ETH_MACCFG_DM | \ + ETH_MACCFG_LM | ETH_MACCFG_DO | ETH_MACCFG_FES | ETH_MACCFG_DCRS | \ + ETH_MACCFG_JE | ETH_MACCFG_IFG_MASK | ETH_MACCFG_JD | ETH_MACCFG_WD) + + +/* The following bits are set or left zero unconditionally in all modes. + * + * ETH_MACCFG_RE Receiver enable 0 (disabled) + * ETH_MACCFG_TE Transmitter enable 0 (disabled) + * ETH_MACCFG_DC Deferral check 0 (disabled) + * ETH_MACCFG_BL Back-off limit 0 (10) + * ETH_MACCFG_APCS Automatic pad/CRC stripping 0 (disabled) + * ETH_MACCFG_RD Retry disable 1 (disabled) + * ETH_MACCFG_LM Loopback mode 0 (disabled) + * ETH_MACCFG_ROD Receive own disable 0 (enabled) + * ETH_MACCFG_CSD Carrier sense disable 0 (enabled) + * ETH_MACCFG_IFG Interframe gap 0 (96 bits) + * ETH_MACCFG_JD Jabber disable 0 (enabled) + * ETH_MACCFG_WD Watchdog disable 0 (enabled) + * ETH_MACCFG_CSTF CRC stripping for Type frames 0 (disabled, F2/F4 only) + * + * The following are set conditioinally based on mode and speed. + * + * ETH_MACCFG_DM Duplex mode Depends on priv->fduplex + * ETH_MACCFG_FES Fast Ethernet speed Depends on priv->mbps100 + */ + +# define MACCR_SET_BITS \ + (ETH_MACCFG_BL_10 | ETH_MACCFG_RD | ETH_MACCFG_IFG(96)) + + +/* Clear the MACCR bits that will be setup during MAC initialization (or that + * are cleared unconditionally). Per the reference manual, all reserved bits + * must be retained at their reset value. + * + * ETH_MACFFR_PM Bit 0: Promiscuous mode + * ETH_MACFFR_HU Bit 1: Hash unicast + * ETH_MACFFR_HM Bit 2: Hash multicast + * ETH_MACFFR_DAIF Bit 3: Destination address inverse filtering + * ETH_MACFFR_PAM Bit 4: Pass all multicast + * ETH_MACFFR_BFD Bit 5: Broadcast frames disable + * ETH_MACFFR_PCF Bits 6-7: Pass control frames + * ETH_MACFFR_SAIF Bit 8: Source address inverse filtering + * ETH_MACFFR_SAF Bit 9: Source address filter + * ETH_MACFFR_HPF Bit 10: Hash or perfect filter + * ETH_MACFFR_RA Bit 31: Receive all + */ + +#define MACFFR_CLEAR_BITS \ + (ETH_MACFFLT_PR | ETH_MACFFLT_HUC | ETH_MACFFLT_HMC | ETH_MACFFLT_DAIF | \ + ETH_MACFFLT_PM | ETH_MACFFLT_DBF | ETH_MACFFLT_PCF_MASK | ETH_MACFFLT_HPF | \ + ETH_MACFFLT_RA) + +/* The following bits are set or left zero unconditionally in all modes. + * + * ETH_MACFFLT_PM Promiscuous mode 0 (disabled) + * ETH_MACFFLT_HU Hash unicast 0 (perfect dest filtering) + * ETH_MACFFLT_HM Hash multicast 0 (perfect dest filtering) + * ETH_MACFFLT_DAIF Destination address inverse filtering 0 (normal) + * ETH_MACFFLT_PAM Pass all multicast 0 (Depends on HM bit) + * ETH_MACFFLT_BFD Broadcast frames disable 0 (enabled) + * ETH_MACFFLT_PCF Pass control frames 1 (block all but PAUSE) + * ETH_MACFFLT_HPF Hash or perfect filter 0 (Only matching frames passed) + * ETH_MACFFLT_RA Receive all 0 (disabled) + */ + +#define MACFFR_SET_BITS (ETH_MACFFLT_PCF_PAUSE) + +/* Clear the MACFCR bits that will be setup during MAC initialization (or that + * are cleared unconditionally). Per the reference manual, all reserved bits + * must be retained at their reset value. + * + * ETH_MACFCR_FCB_BPA Bit 0: Flow control busy/back pressure activate + * ETH_MACFCR_TFCE Bit 1: Transmit flow control enable + * ETH_MACFCR_RFCE Bit 2: Receive flow control enable + * ETH_MACFCR_UPFD Bit 3: Unicast pause frame detect + * ETH_MACFCR_PLT Bits 4-5: Pause low threshold + * ETH_MACFCR_ZQPD Bit 7: Zero-quanta pause disable + * ETH_MACFCR_PT Bits 16-31: Pause time + */ + +#define MACFCR_CLEAR_MASK \ + (ETH_MACFC_FCB | ETH_MACFC_TFE | ETH_MACFC_RFE | ETH_MACFC_UP | \ + ETH_MACFC_PLT_MASK | ETH_MACFC_DZPQ | ETH_MACFC_PT_MASK) + +/* The following bits are set or left zero unconditionally in all modes. + * + * ETH_MACFCR_FCB_BPA Flow control busy/back pressure activate 0 (no pause control frame) + * ETH_MACFCR_TFCE Transmit flow control enable 0 (disabled) + * ETH_MACFCR_RFCE Receive flow control enable 0 (disabled) + * ETH_MACFCR_UPFD Unicast pause frame detect 0 (disabled) + * ETH_MACFCR_PLT Pause low threshold 0 (pause time - 4) + * ETH_MACFCR_ZQPD Zero-quanta pause disable 1 (disabled) + * ETH_MACFCR_PT Pause time 0 + */ + +#define MACFCR_SET_MASK (ETH_MACFC_PLT(4) | ETH_MACFC_DZPQ) + +/* Clear the DMAOMR bits that will be setup during MAC initialization (or that + * are cleared unconditionally). Per the reference manual, all reserved bits + * must be retained at their reset value. + * + * ETH_DMAOPMODE_SR Bit 1: Start/stop receive + * TH_DMAOMR_OSF Bit 2: Operate on second frame + * ETH_DMAOPMODE_RTC Bits 3-4: Receive threshold control + * ETH_DMAOPMODE_FUGF Bit 6: Forward undersized good frames + * ETH_DMAOPMODE_FEF Bit 7: Forward error frames + * ETH_DMAOPMODE_ST Bit 13: Start/stop transmission + * ETH_DMAOPMODE_TTC Bits 14-16: Transmit threshold control + * ETH_DMAOPMODE_FTF Bit 20: Flush transmit FIFO + * ETH_DMAOPMODE_TSF Bit 21: Transmit store and forward + * ETH_DMAOPMODE_DFRF Bit 24: Disable flushing of received frames + * ETH_DMAOPMODE_RSF Bit 25: Receive store and forward + * TH_DMAOMR_DTCEFD Bit 26: Dropping of TCP/IP checksum error frames disable + */ + +#define DMAOMR_CLEAR_MASK \ + (ETH_DMAOPMODE_SR | ETH_DMAOPMODE_OSF | ETH_DMAOPMODE_RTC_MASK | ETH_DMAOPMODE_FUF | \ + ETH_DMAOPMODE_FEF | ETH_DMAOPMODE_ST | ETH_DMAOPMODE_TTC_MASK | ETH_DMAOPMODE_FTF | \ + ETH_DMAOPMODE_DFF) + +/* The following bits are set or left zero unconditionally in all modes. + * + * ETH_DMAOPMODE_SR Start/stop receive 0 (not running) + * TH_DMAOMR_OSF Operate on second frame 1 (enabled) + * ETH_DMAOPMODE_RTC Receive threshold control 0 (64 bytes) + * ETH_DMAOPMODE_FUGF Forward undersized good frames 0 (disabled) + * ETH_DMAOPMODE_FEF Forward error frames 0 (disabled) + * ETH_DMAOPMODE_ST Start/stop transmission 0 (not running) + * ETH_DMAOPMODE_TTC Transmit threshold control 0 (64 bytes) + * ETH_DMAOPMODE_FTF Flush transmit FIFO 0 (no flush) + * ETH_DMAOPMODE_TSF Transmit store and forward Depends on CONFIG_LPC43_ETH_HWCHECKSUM + * ETH_DMAOPMODE_DFRF Disable flushing of received frames 0 (enabled) + * ETH_DMAOPMODE_RSF Receive store and forward Depends on CONFIG_LPC43_ETH_HWCHECKSUM + * TH_DMAOMR_DTCEFD Dropping of TCP/IP checksum error Depends on CONFIG_LPC43_ETH_HWCHECKSUM + * frames disable + * + * When the checksum offload feature is enabled, we need to enable the Store + * and Forward mode: the store and forward guarantee that a whole frame is + * stored in the FIFO, so the MAC can insert/verify the checksum, if the + * checksum is OK the DMA can handle the frame otherwise the frame is dropped + */ + +#if CONFIG_LPC43_ETH_HWCHECKSUM +# define DMAOMR_SET_MASK \ + (ETH_DMAOPMODE_OSF | ETH_DMAOPMODE_RTC_64 | ETH_DMAOPMODE_TTC_64 | \ + ETH_DMAOPMODE_TSF | ETH_DMAOPMODE_RSF) +#else +# define DMAOMR_SET_MASK \ + (ETH_DMAOPMODE_OSF | ETH_DMAOPMODE_RTC_64 | ETH_DMAOPMODE_TTC_64) +#endif + +/* Clear the DMABMR bits that will be setup during MAC initialization (or that + * are cleared unconditionally). Per the reference manual, all reserved bits + * must be retained at their reset value. + * + * ETH_DMABMODE_SR Bit 0: Software reset + * ETH_DMABMODE_DA Bit 1: DMA Arbitration + * ETH_DMABMODE_DSL Bits 2-6: Descriptor skip length + * ETH_DMABMODE_ATDS Bit 7: Enhanced descriptor format enable + * ETH_DMABMODE_PBL Bits 8-13: Programmable burst length + * ETH_DMABMODE_RTPR Bits 14-15: RX TX priority ratio + * ETH_DMABMODE_FB Bit 16: Fixed burst + * ETH_DMABMODE_RDP Bits 17-22: RX DMA PBL + * ETH_DMABMODE_USP Bit 23: Use separate PBL + * ETH_DMABMODE_FPM Bit 24: 4xPBL mode + * ETH_DMABMODE_AAB Bit 25: Address-aligned beats + * ETH_DMABMODE_MB Bit 26: Mixed burst (F2/F4 only) + */ + +#define DMABMR_CLEAR_MASK \ + (ETH_DMABMODE_SWR | ETH_DMABMODE_DA | ETH_DMABMODE_DSL_MASK | ETH_DMABMODE_ATDS | \ + ETH_DMABMODE_PBL_MASK | ETH_DMABMODE_PR_MASK | ETH_DMABMODE_FB | ETH_DMABMODE_RPBL_MASK | \ + ETH_DMABMODE_USP | ETH_DMABMODE_PBL8X | ETH_DMABMODE_AAL | ETH_DMABMODE_MB | ETH_DMABMODE_TXPR ) + + +/* The following bits are set or left zero unconditionally in all modes. + * + * + * ETH_DMABMODE_SR Software reset 0 (no reset) + * ETH_DMABMODE_DA DMA Arbitration 0 (round robin) + * ETH_DMABMODE_DSL Descriptor skip length 0 + * ETH_DMABMODE_ATDS Enhanced descriptor format enable Depends on CONFIG_LPC43_ETH_ENHANCEDDESC + * ETH_DMABMODE_PBL Programmable burst length 32 beats + * ETH_DMABMODE_RTPR RX TX priority ratio 2:1 + * ETH_DMABMODE_FB Fixed burst 1 (enabled) + * ETH_DMABMODE_RDP RX DMA PBL 32 beats + * ETH_DMABMODE_USP Use separate PBL 1 (enabled) + * ETH_DMABMODE_FPM 4xPBL mode 0 (disabled) + * ETH_DMABMODE_AAB Address-aligned beats 1 (enabled) + * ETH_DMABMODE_MB Mixed burst 0 (disabled, F2/F4 only) + */ + +#ifdef CONFIG_LPC43_ETH_ENHANCEDDESC +# define DMABMR_SET_MASK \ + (ETH_DMABMODE_DSL(0) | ETH_DMABMODE_PBL(32) | ETH_DMABMODE_ATDS | ETH_DMABMODE_RTPR_2TO1 | \ + ETH_DMABMODE_FB | ETH_DMABMODE_RPBL(32) | ETH_DMABMODE_USP | ETH_DMABMODE_AAB) +#else +# define DMABMR_SET_MASK \ + (ETH_DMABMODE_DSL(0) | ETH_DMABMODE_PBL(32) | ETH_DMABMODE_PR_2TO1 | ETH_DMABMODE_FB | \ + ETH_DMABMODE_RPBL(32) | ETH_DMABMODE_USP | ETH_DMABMODE_AAL) +#endif + +/* Interrupt bit sets *******************************************************/ +/* All interrupts in the normal and abnormal interrupt summary. Early transmit + * interrupt (ETI) is excluded from the abnormal set because it causes too + * many interrupts and is not interesting. + */ + +#define ETH_DMAINT_NORMAL \ + (ETH_DMAINT_TI | ETH_DMAINT_TU |ETH_DMAINT_RI | ETH_DMAINT_ERI) + +#define ETH_DMAINT_ABNORMAL \ + (ETH_DMAINT_TPS | ETH_DMAINT_TJT | ETH_DMAINT_OVF | ETH_DMAINT_UNF | \ + ETH_DMAINT_RU | ETH_DMAINT_RPS | ETH_DMAINT_RWT | /* ETH_DMAINT_ETI | */ \ + ETH_DMAINT_FBI) + +/* Normal receive, transmit, error interrupt enable bit sets */ + +#define ETH_DMAINT_RECV_ENABLE (ETH_DMAINT_NIS | ETH_DMAINT_RI) +#define ETH_DMAINT_XMIT_ENABLE (ETH_DMAINT_NIS | ETH_DMAINT_TI) +#define ETH_DMAINT_XMIT_DISABLE (ETH_DMAINT_TI) + +#ifdef CONFIG_DEBUG_NET +# define ETH_DMAINT_ERROR_ENABLE (ETH_DMAINT_AIS | ETH_DMAINT_ABNORMAL) +#else +# define ETH_DMAINT_ERROR_ENABLE (0) +#endif + +/* Helpers ******************************************************************/ +/* This is a helper pointer for accessing the contents of the Ethernet + * header + */ + +#define BUF ((struct eth_hdr_s *)priv->dev.d_buf) + +/**************************************************************************** + * Private Types + ****************************************************************************/ + +/* The lpc43_ethmac_s encapsulates all state information for a single hardware + * interface + */ + +struct lpc43_ethmac_s +{ + uint8_t ifup : 1; /* true:ifup false:ifdown */ + uint8_t mbps100 : 1; /* 100MBps operation (vs 10 MBps) */ + uint8_t fduplex : 1; /* Full (vs. half) duplex */ + WDOG_ID txpoll; /* TX poll timer */ + WDOG_ID txtimeout; /* TX timeout timer */ +#ifdef CONFIG_NET_NOINTS + struct work_s work; /* For deferring work to the work queue */ +#endif + + /* This holds the information visible to uIP/NuttX */ + + struct net_driver_s dev; /* Interface understood by uIP */ + + /* Used to track transmit and receive descriptors */ + + struct eth_txdesc_s *txhead; /* Next available TX descriptor */ + struct eth_rxdesc_s *rxhead; /* Next available RX descriptor */ + + struct eth_txdesc_s *txtail; /* First "in_flight" TX descriptor */ + struct eth_rxdesc_s *rxcurr; /* First RX descriptor of the segment */ + uint16_t segments; /* RX segment count */ + uint16_t inflight; /* Number of TX transfers "in_flight" */ + sq_queue_t freeb; /* The free buffer list */ + + /* Descriptor allocations */ + + struct eth_rxdesc_s rxtable[CONFIG_LPC43_ETH_NRXDESC]; + struct eth_txdesc_s txtable[CONFIG_LPC43_ETH_NTXDESC]; + + /* Buffer allocations */ + + uint8_t rxbuffer[CONFIG_LPC43_ETH_NRXDESC*CONFIG_LPC43_ETH_BUFSIZE]; + uint8_t alloc[LPC43_ETH_NFREEBUFFERS*CONFIG_LPC43_ETH_BUFSIZE]; +}; + +/**************************************************************************** + * Private Data + ****************************************************************************/ + +static struct lpc43_ethmac_s g_lpc43ethmac; + +/**************************************************************************** + * Private Function Prototypes + ****************************************************************************/ +/* Register operations ******************************************************/ + +#if defined(CONFIG_LPC43_ETHMAC_REGDEBUG) && defined(CONFIG_DEBUG) +static uint32_t lpc43_getreg(uint32_t addr); +static void lpc43_putreg(uint32_t val, uint32_t addr); +static void lpc43_checksetup(void); +#else +# define lpc43_getreg(addr) getreg32(addr) +# define lpc43_putreg(val,addr) putreg32(val,addr) +# define lpc43_checksetup() +#endif + +/* Free buffer management */ + +static void lpc43_initbuffer(FAR struct lpc43_ethmac_s *priv); +static inline uint8_t *lpc43_allocbuffer(FAR struct lpc43_ethmac_s *priv); +static inline void lpc43_freebuffer(FAR struct lpc43_ethmac_s *priv, uint8_t *buffer); +static inline bool lpc43_isfreebuffer(FAR struct lpc43_ethmac_s *priv); + +/* Common TX logic */ + +static int lpc43_transmit(FAR struct lpc43_ethmac_s *priv); +static int lpc43_txpoll(struct net_driver_s *dev); +static void lpc43_dopoll(FAR struct lpc43_ethmac_s *priv); + +/* Interrupt handling */ + +static void lpc43_enableint(FAR struct lpc43_ethmac_s *priv, uint32_t ierbit); +static void lpc43_disableint(FAR struct lpc43_ethmac_s *priv, uint32_t ierbit); + +static void lpc43_freesegment(FAR struct lpc43_ethmac_s *priv, + FAR struct eth_rxdesc_s *rxfirst, int segments); +static int lpc43_recvframe(FAR struct lpc43_ethmac_s *priv); +static void lpc43_receive(FAR struct lpc43_ethmac_s *priv); +static void lpc43_freeframe(FAR struct lpc43_ethmac_s *priv); +static void lpc43_txdone(FAR struct lpc43_ethmac_s *priv); +#ifdef CONFIG_NET_NOINTS +static void lpc43_interrupt_work(FAR void *arg); +#endif +static int lpc43_interrupt(int irq, FAR void *context); + +/* Watchdog timer expirations */ + +static inline void lpc43_txtimeout_process(FAR struct lpc43_ethmac_s *priv); +#ifdef CONFIG_NET_NOINTS +static void lpc43_txtimeout_work(FAR void *arg); +#endif +static void lpc43_txtimeout_expiry(int argc, uint32_t arg, ...); + +static inline void lpc43_poll_process(FAR struct lpc43_ethmac_s *priv); +#ifdef CONFIG_NET_NOINTS +static void lpc43_poll_work(FAR void *arg); +#endif +static void lpc43_poll_expiry(int argc, uint32_t arg, ...); + +/* NuttX callback functions */ + +static int lpc43_ifup(struct net_driver_s *dev); +static int lpc43_ifdown(struct net_driver_s *dev); +static inline void lpc43_txavail_process(FAR struct lpc43_ethmac_s *priv); +#ifdef CONFIG_NET_NOINTS +static void lpc43_txavail_work(FAR void *arg); +#endif +static int lpc43_txavail(struct net_driver_s *dev); +#if defined(CONFIG_NET_IGMP) || defined(CONFIG_NET_ICMPv6) +static int lpc43_addmac(struct net_driver_s *dev, FAR const uint8_t *mac); +#endif +#ifdef CONFIG_NET_IGMP +static int lpc43_rmmac(struct net_driver_s *dev, FAR const uint8_t *mac); +#endif +#ifdef CONFIG_NETDEV_PHY_IOCTL +static int lpc43_ioctl(struct net_driver_s *dev, int cmd, long arg); +#endif +/* Descriptor Initialization */ + +static void lpc43_txdescinit(FAR struct lpc43_ethmac_s *priv); +static void lpc43_rxdescinit(FAR struct lpc43_ethmac_s *priv); + +/* PHY Initialization */ +#if defined(CONFIG_NETDEV_PHY_IOCTL) && defined(CONFIG_ARCH_PHY_INTERRUPT) +static int lpc43_phyintenable(FAR struct lpc43_ethmac_s *priv); +#endif +static int lpc43_phyread(uint16_t phydevaddr, uint16_t phyregaddr, uint16_t *value); +static int lpc43_phywrite(uint16_t phydevaddr, uint16_t phyregaddr, uint16_t value); +#ifdef CONFIG_ETH0_PHY_DM9161 +static inline int lpc43_dm9161(FAR struct lpc43_ethmac_s *priv); +#endif +static int lpc43_phyinit(FAR struct lpc43_ethmac_s *priv); + +/* MAC/DMA Initialization */ + +#ifdef CONFIG_LPC43_MII +static inline void lpc43_selectmii(void); +#endif +#ifdef CONFIG_LPC43_RMII +static inline void lpc43_selectrmii(void); +#endif +static inline void lpc43_ethgpioconfig(FAR struct lpc43_ethmac_s *priv); +static void lpc43_ethreset(FAR struct lpc43_ethmac_s *priv); +static int lpc43_macconfig(FAR struct lpc43_ethmac_s *priv); +static void lpc43_macaddress(FAR struct lpc43_ethmac_s *priv); +#ifdef CONFIG_NET_ICMPv6 +static void lpc43_ipv6multicast(FAR struct lpc43_ethmac_s *priv); +#endif +static int lpc43_macenable(FAR struct lpc43_ethmac_s *priv); +static int lpc43_ethconfig(FAR struct lpc43_ethmac_s *priv); + +/**************************************************************************** + * Private Functions + ****************************************************************************/ +/**************************************************************************** + * Name: lpc43_getreg + * + * Description: + * This function may to used to intercept an monitor all register accesses. + * Clearly this is nothing you would want to do unless you are debugging + * this driver. + * + * Input Parameters: + * addr - The register address to read + * + * Returned Value: + * The value read from the register + * + ****************************************************************************/ + +#if defined(CONFIG_LPC43_ETHMAC_REGDEBUG) && defined(CONFIG_DEBUG) +static uint32_t lpc43_getreg(uint32_t addr) +{ + static uint32_t prevaddr = 0; + static uint32_t preval = 0; + static uint32_t count = 0; + + /* Read the value from the register */ + + uint32_t val = getreg32(addr); + + /* Is this the same value that we read from the same register last time? + * Are we polling the register? If so, suppress some of the output. + */ + + if (addr == prevaddr && val == preval) + { + if (count == 0xffffffff || ++count > 3) + { + if (count == 4) + { + lldbg("...\n"); + } + return val; + } + } + + /* No this is a new address or value */ + + else + { + /* Did we print "..." for the previous value? */ + + if (count > 3) + { + /* Yes.. then show how many times the value repeated */ + + lldbg("[repeats %d more times]\n", count-3); + } + + /* Save the new address, value, and count */ + + prevaddr = addr; + preval = val; + count = 1; + } + + /* Show the register value read */ + + lldbg("%08x->%08x\n", addr, val); + return val; +} +#endif + +/**************************************************************************** + * Name: lpc43_putreg + * + * Description: + * This function may to used to intercept an monitor all register accesses. + * Clearly this is nothing you would want to do unless you are debugging + * this driver. + * + * Input Parameters: + * val - The value to write to the register + * addr - The register address to read + * + * Returned Value: + * None + * + ****************************************************************************/ + +#if defined(CONFIG_LPC43_ETHMAC_REGDEBUG) && defined(CONFIG_DEBUG) +static void lpc43_putreg(uint32_t val, uint32_t addr) +{ + /* Show the register value being written */ + + lldbg("%08x<-%08x\n", addr, val); + + /* Write the value */ + + putreg32(val, addr); +} +#endif + +/**************************************************************************** + * Name: lpc43_checksetup + * + * Description: + * Show the state of critical configuration registers. + * + * Input Parameters: + * None + * + * Returned Value: + * None + * + ****************************************************************************/ + +#if defined(CONFIG_LPC43_ETHMAC_REGDEBUG) && defined(CONFIG_DEBUG) +static void lpc43_checksetup(void) +{ +} +#endif + +/**************************************************************************** + * Function: lpc43_initbuffer + * + * Description: + * Initialize the free buffer list. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Called during early driver initialization before Ethernet interrupts + * are enabled. + * + ****************************************************************************/ + +static void lpc43_initbuffer(FAR struct lpc43_ethmac_s *priv) +{ + uint8_t *buffer; + int i; + + /* Initialize the head of the free buffer list */ + + sq_init(&priv->freeb); + + /* Add all of the pre-allocated buffers to the free buffer list */ + + for (i = 0, buffer = priv->alloc; + i < LPC43_ETH_NFREEBUFFERS; + i++, buffer += CONFIG_LPC43_ETH_BUFSIZE) + { + sq_addlast((FAR sq_entry_t *)buffer, &priv->freeb); + } +} + +/**************************************************************************** + * Function: lpc43_allocbuffer + * + * Description: + * Allocate one buffer from the free buffer list. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * Pointer to the allocated buffer on success; NULL on failure + * + * Assumptions: + * May or may not be called from an interrupt handler. In either case, + * global interrupts are disabled, either explicitly or indirectly through + * interrupt handling logic. + * + ****************************************************************************/ + +static inline uint8_t *lpc43_allocbuffer(FAR struct lpc43_ethmac_s *priv) +{ + /* Allocate a buffer by returning the head of the free buffer list */ + + return (uint8_t *)sq_remfirst(&priv->freeb); +} + +/**************************************************************************** + * Function: lpc43_freebuffer + * + * Description: + * Return a buffer to the free buffer list. + * + * Parameters: + * priv - Reference to the driver state structure + * buffer - A pointer to the buffer to be freed + * + * Returned Value: + * None + * + * Assumptions: + * May or may not be called from an interrupt handler. In either case, + * global interrupts are disabled, either explicitly or indirectly through + * interrupt handling logic. + * + ****************************************************************************/ + +static inline void lpc43_freebuffer(FAR struct lpc43_ethmac_s *priv, uint8_t *buffer) +{ + /* Free the buffer by adding it to to the end of the free buffer list */ + + sq_addlast((FAR sq_entry_t *)buffer, &priv->freeb); +} + +/**************************************************************************** + * Function: lpc43_isfreebuffer + * + * Description: + * Return TRUE if the free buffer list is not empty. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * True if there are one or more buffers in the free buffer list; + * false if the free buffer list is empty + * + * Assumptions: + * None. + * + ****************************************************************************/ + +static inline bool lpc43_isfreebuffer(FAR struct lpc43_ethmac_s *priv) +{ + /* Return TRUE if the free buffer list is not empty */ + + return !sq_empty(&priv->freeb); +} + +/**************************************************************************** + * Function: lpc43_transmit + * + * Description: + * Start hardware transmission. Called either from the txdone interrupt + * handling or from watchdog based polling. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * OK on success; a negated errno on failure + * + * Assumptions: + * May or may not be called from an interrupt handler. In either case, + * global interrupts are disabled, either explicitly or indirectly through + * interrupt handling logic. + * + ****************************************************************************/ + +static int lpc43_transmit(FAR struct lpc43_ethmac_s *priv) +{ + struct eth_txdesc_s *txdesc; + struct eth_txdesc_s *txfirst; + + /* The internal (optimal) uIP buffer size may be configured to be larger + * than the Ethernet buffer size. + */ + +#if OPTIMAL_ETH_BUFSIZE > CONFIG_LPC43_ETH_BUFSIZE + uint8_t *buffer; + int bufcount; + int lastsize; + int i; +#endif + + /* Verify that the hardware is ready to send another packet. If we get + * here, then we are committed to sending a packet; Higher level logic + * must have assured that there is no transmission in progress. + */ + + txdesc = priv->txhead; + txfirst = txdesc; + + nllvdbg("d_len: %d d_buf: %p txhead: %p tdes0: %08x\n", + priv->dev.d_len, priv->dev.d_buf, txdesc, txdesc->tdes0); + + DEBUGASSERT(txdesc && (txdesc->tdes0 & ETH_TDES0_OWN) == 0); + + /* Is the size to be sent greater than the size of the Ethernet buffer? */ + + DEBUGASSERT(priv->dev.d_len > 0 && priv->dev.d_buf != NULL); + +#if OPTIMAL_ETH_BUFSIZE > CONFIG_LPC43_ETH_BUFSIZE + if (priv->dev.d_len > CONFIG_LPC43_ETH_BUFSIZE) + { + /* Yes... how many buffers will be need to send the packet? */ + + bufcount = (priv->dev.d_len + (CONFIG_LPC43_ETH_BUFSIZE-1)) / CONFIG_LPC43_ETH_BUFSIZE; + lastsize = priv->dev.d_len - (bufcount - 1) * CONFIG_LPC43_ETH_BUFSIZE; + + nllvdbg("bufcount: %d lastsize: %d\n", bufcount, lastsize); + + /* Set the first segment bit in the first TX descriptor */ + + txdesc->tdes0 |= ETH_TDES0_FS; + + /* Set up all but the last TX descriptor */ + + buffer = priv->dev.d_buf; + + for (i = 0; i < bufcount; i++) + { + /* This could be a normal event but the design does not handle it */ + + DEBUGASSERT((txdesc->tdes0 & ETH_TDES0_OWN) == 0); + + /* Set the Buffer1 address pointer */ + + txdesc->tdes2 = (uint32_t)buffer; + + /* Set the buffer size in all TX descriptors */ + + if (i == (bufcount-1)) + { + /* This is the last segment. Set the last segment bit in the + * last TX descriptor and ask for an interrupt when this + * segment transfer completes. + */ + + txdesc->tdes0 |= (ETH_TDES0_LS | ETH_TDES0_IC); + + /* This segement is, most likely, of fractional buffersize */ + + txdesc->tdes1 = lastsize; + buffer += lastsize; + } + else + { + /* This is not the last segment. We don't want an interrupt + * when this segment transfer completes. + */ + + txdesc->tdes0 &= ~ETH_TDES0_IC; + + /* The size of the transfer is the whole buffer */ + + txdesc->tdes1 = CONFIG_LPC43_ETH_BUFSIZE; + buffer += CONFIG_LPC43_ETH_BUFSIZE; + } + + /* Give the descriptor to DMA */ + + txdesc->tdes0 |= ETH_TDES0_OWN; + txdesc = (struct eth_txdesc_s *)txdesc->tdes3; + } + } + else +#endif + { + /* The single descriptor is both the first and last segment. And we do + * want an interrupt when the transfer completes. + */ + + txdesc->tdes0 |= (ETH_TDES0_FS | ETH_TDES0_LS | ETH_TDES0_IC); + + /* Set frame size */ + + DEBUGASSERT(priv->dev.d_len <= CONFIG_NET_ETH_MTU); + txdesc->tdes1 = priv->dev.d_len; + + /* Set the Buffer1 address pointer */ + + txdesc->tdes2 = (uint32_t)priv->dev.d_buf; + + /* Set OWN bit of the TX descriptor tdes0. This gives the buffer to + * Ethernet DMA + */ + + txdesc->tdes0 |= ETH_TDES0_OWN; + + /* Point to the next available TX descriptor */ + + txdesc = (struct eth_txdesc_s *)txdesc->tdes3; + } + + /* Remember where we left off in the TX descriptor chain */ + + priv->txhead = txdesc; + + /* Detach the buffer from priv->dev structure. That buffer is now + * "in-flight". + */ + + priv->dev.d_buf = NULL; + priv->dev.d_len = 0; + + /* If there is no other TX buffer, in flight, then remember the location + * of the TX descriptor. This is the location to check for TX done events. + */ + + if (!priv->txtail) + { + DEBUGASSERT(priv->inflight == 0); + priv->txtail = txfirst; + } + + /* Increment the number of TX transfer in-flight */ + + priv->inflight++; + + nllvdbg("txhead: %p txtail: %p inflight: %d\n", + priv->txhead, priv->txtail, priv->inflight); + + /* If all TX descriptors are in-flight, then we have to disable receive interrupts + * too. This is because receive events can trigger more un-stoppable transmit + * events. + */ + + if (priv->inflight >= CONFIG_LPC43_ETH_NTXDESC) + { + lpc43_disableint(priv, ETH_DMAINT_RI); + } + + /* Check if the TX Buffer unavailable flag is set */ + + if ((lpc43_getreg(LPC43_ETH_DMASTAT) & ETH_DMAINT_TU) != 0) + { + /* Clear TX Buffer unavailable flag */ + + lpc43_putreg(ETH_DMAINT_TU, LPC43_ETH_DMASTAT); + + /* Resume DMA transmission */ + + lpc43_putreg(0, LPC43_ETH_DMATXPD); + } + + /* Enable TX interrupts */ + + lpc43_enableint(priv, ETH_DMAINT_TI); + + /* Setup the TX timeout watchdog (perhaps restarting the timer) */ + + (void)wd_start(priv->txtimeout, LPC43_TXTIMEOUT, lpc43_txtimeout_expiry, 1, (uint32_t)priv); + return OK; +} + +/**************************************************************************** + * Function: lpc43_txpoll + * + * Description: + * The transmitter is available, check if uIP has any outgoing packets ready + * to send. This is a callback from devif_poll(). devif_poll() may be called: + * + * 1. When the preceding TX packet send is complete, + * 2. When the preceding TX packet send timesout and the interface is reset + * 3. During normal TX polling + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * + * Returned Value: + * OK on success; a negated errno on failure + * + * Assumptions: + * May or may not be called from an interrupt handler. In either case, + * global interrupts are disabled, either explicitly or indirectly through + * interrupt handling logic. + * + ****************************************************************************/ + +static int lpc43_txpoll(struct net_driver_s *dev) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)dev->d_private; + + DEBUGASSERT(priv->dev.d_buf != NULL); + + /* If the polling resulted in data that should be sent out on the network, + * the field d_len is set to a value > 0. + */ + + if (priv->dev.d_len > 0) + { + /* Look up the destination MAC address and add it to the Ethernet + * header. + */ + +#ifdef CONFIG_NET_IPv4 +#ifdef CONFIG_NET_IPv6 + if (IFF_IS_IPv4(priv->dev.d_flags)) +#endif + { + arp_out(&priv->dev); + } +#endif /* CONFIG_NET_IPv4 */ + +#ifdef CONFIG_NET_IPv6 +#ifdef CONFIG_NET_IPv4 + else +#endif + { + neighbor_out(&priv->dev); + } +#endif /* CONFIG_NET_IPv6 */ + + /* Send the packet */ + + lpc43_transmit(priv); + DEBUGASSERT(dev->d_len == 0 && dev->d_buf == NULL); + + /* Check if the next TX descriptor is owned by the Ethernet DMA or CPU. We + * cannot perform the TX poll if we are unable to accept another packet for + * transmission. + * + * In a race condition, ETH_TDES0_OWN may be cleared BUT still not available + * because lpc43_freeframe() has not yet run. If lpc43_freeframe() has run, + * the buffer1 pointer (tdes2) will be nullified (and inflight should be < + * CONFIG_LPC43_ETH_NTXDESC). + */ + + if ((priv->txhead->tdes0 & ETH_TDES0_OWN) != 0 || + priv->txhead->tdes2 != 0) + { + /* We have to terminate the poll if we have no more descriptors + * available for another transfer. + */ + + return -EBUSY; + } + + /* We have the descriptor, we can continue the poll. Allocate a new + * buffer for the poll. + */ + + dev->d_buf = lpc43_allocbuffer(priv); + + /* We can't continue the poll if we have no buffers */ + + if (dev->d_buf == NULL) + { + /* Terminate the poll. */ + + return -ENOMEM; + } + } + + /* If zero is returned, the polling will continue until all connections have + * been examined. + */ + + return 0; +} + +/**************************************************************************** + * Function: lpc43_dopoll + * + * Description: + * The function is called when a frame is received using the DMA receive + * interrupt. It scans the RX descriptors to the received frame. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by interrupt handling logic. + * + ****************************************************************************/ + +static void lpc43_dopoll(FAR struct lpc43_ethmac_s *priv) +{ + FAR struct net_driver_s *dev = &priv->dev; + + /* Check if the next TX descriptor is owned by the Ethernet DMA or + * CPU. We cannot perform the TX poll if we are unable to accept + * another packet for transmission. + * + * In a race condition, ETH_TDES0_OWN may be cleared BUT still not available + * because lpc43_freeframe() has not yet run. If lpc43_freeframe() has run, + * the buffer1 pointer (tdes2) will be nullified (and inflight should be < + * CONFIG_LPC43_ETH_NTXDESC). + */ + + if ((priv->txhead->tdes0 & ETH_TDES0_OWN) == 0 && + priv->txhead->tdes2 == 0) + { + /* If we have the descriptor, then poll for new XMIT data. + * Allocate a buffer for the poll. + */ + + DEBUGASSERT(dev->d_len == 0 && dev->d_buf == NULL); + dev->d_buf = lpc43_allocbuffer(priv); + + /* We can't poll if we have no buffers */ + + if (dev->d_buf) + { + (void)devif_poll(dev, lpc43_txpoll); + + /* We will, most likely end up with a buffer to be freed. But it + * might not be the same one that we allocated above. + */ + + if (dev->d_buf) + { + DEBUGASSERT(dev->d_len == 0); + lpc43_freebuffer(priv, dev->d_buf); + dev->d_buf = NULL; + } + } + } +} + +/**************************************************************************** + * Function: lpc43_enableint + * + * Description: + * Enable a "normal" interrupt + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by interrupt handling logic. + * + ****************************************************************************/ + +static void lpc43_enableint(FAR struct lpc43_ethmac_s *priv, uint32_t ierbit) +{ + uint32_t regval; + + /* Enable the specified "normal" interrupt */ + + regval = lpc43_getreg(LPC43_ETH_DMAINTEN); + regval |= (ETH_DMAINT_NIS | ierbit); + lpc43_putreg(regval, LPC43_ETH_DMAINTEN); +} + +/**************************************************************************** + * Function: lpc43_disableint + * + * Description: + * Disable a normal interrupt. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by interrupt handling logic. + * + ****************************************************************************/ + +static void lpc43_disableint(FAR struct lpc43_ethmac_s *priv, uint32_t ierbit) +{ + uint32_t regval; + + /* Disable the "normal" interrupt */ + + regval = lpc43_getreg(LPC43_ETH_DMAINTEN); + regval &= ~ierbit; + + /* Are all "normal" interrupts now disabled? */ + + if ((regval & ETH_DMAINT_NORMAL) == 0) + { + /* Yes.. disable normal interrupts */ + + regval &= ~ETH_DMAINT_NIS; + } + + lpc43_putreg(regval, LPC43_ETH_DMAINTEN); +} + +/**************************************************************************** + * Function: lpc43_freesegment + * + * Description: + * The function is called when a frame is received using the DMA receive + * interrupt. It scans the RX descriptors to the received frame. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by interrupt handling logic. + * + ****************************************************************************/ + +static void lpc43_freesegment(FAR struct lpc43_ethmac_s *priv, + FAR struct eth_rxdesc_s *rxfirst, int segments) +{ + struct eth_rxdesc_s *rxdesc; + int i; + + nllvdbg("rxfirst: %p segments: %d\n", rxfirst, segments); + + /* Set OWN bit in RX descriptors. This gives the buffers back to DMA */ + + rxdesc = rxfirst; + for (i = 0; i < segments; i++) + { + rxdesc->rdes0 = ETH_RDES0_OWN; + rxdesc = (struct eth_rxdesc_s *)rxdesc->rdes3; + } + + /* Reset the segment management logic */ + + priv->rxcurr = NULL; + priv->segments = 0; + + /* Check if the RX Buffer unavailable flag is set */ + + if ((lpc43_getreg(LPC43_ETH_DMASTAT) & ETH_DMAINT_RU) != 0) + { + /* Clear RBUS Ethernet DMA flag */ + + lpc43_putreg(ETH_DMAINT_RU, LPC43_ETH_DMASTAT); + + /* Resume DMA reception */ + + lpc43_putreg(0, LPC43_ETH_DMARXPD); + } +} + +/**************************************************************************** + * Function: lpc43_recvframe + * + * Description: + * The function is called when a frame is received using the DMA receive + * interrupt. It scans the RX descriptors of the received frame. + * + * NOTE: This function will silently discard any packets containing errors. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * OK if a packet was successfully returned; -EAGAIN if there are no + * further packets available + * + * Assumptions: + * Global interrupts are disabled by interrupt handling logic. + * + ****************************************************************************/ + +static int lpc43_recvframe(FAR struct lpc43_ethmac_s *priv) +{ + struct eth_rxdesc_s *rxdesc; + struct eth_rxdesc_s *rxcurr; + uint8_t *buffer; + int i; + + nllvdbg("rxhead: %p rxcurr: %p segments: %d\n", + priv->rxhead, priv->rxcurr, priv->segments); + + /* Check if there are free buffers. We cannot receive new frames in this + * design unless there is at least one free buffer. + */ + + if (!lpc43_isfreebuffer(priv)) + { + nlldbg("No free buffers\n"); + return -ENOMEM; + } + + /* Scan descriptors owned by the CPU. Scan until: + * + * 1) We find a descriptor still owned by the DMA, + * 2) We have examined all of the RX descriptors, or + * 3) All of the TX descriptors are in flight. + * + * This last case is obscure. It is due to that fact that each packet + * that we receive can generate an unstoppable transmission. So we have + * to stop receiving when we can not longer transmit. In this case, the + * transmit logic should also have disabled further RX interrupts. + */ + + rxdesc = priv->rxhead; + for (i = 0; + (rxdesc->rdes0 & ETH_RDES0_OWN) == 0 && + i < CONFIG_LPC43_ETH_NRXDESC && + priv->inflight < CONFIG_LPC43_ETH_NTXDESC; + i++) + { + /* Check if this is the first segment in the frame */ + + if ((rxdesc->rdes0 & ETH_RDES0_FS) != 0 && + (rxdesc->rdes0 & ETH_RDES0_LS) == 0) + { + priv->rxcurr = rxdesc; + priv->segments = 1; + } + + /* Check if this is an intermediate segment in the frame */ + + else if (((rxdesc->rdes0 & ETH_RDES0_LS) == 0)&& + ((rxdesc->rdes0 & ETH_RDES0_FS) == 0)) + { + priv->segments++; + } + + /* Otherwise, it is the last segment in the frame */ + + else + { + priv->segments++; + + /* Check if the there is only one segment in the frame */ + + if (priv->segments == 1) + { + rxcurr = rxdesc; + } + else + { + rxcurr = priv->rxcurr; + } + + nllvdbg("rxhead: %p rxcurr: %p segments: %d\n", + priv->rxhead, priv->rxcurr, priv->segments); + + /* Check if any errors are reported in the frame */ + + if ((rxdesc->rdes0 & ETH_RDES0_ES) == 0) + { + struct net_driver_s *dev = &priv->dev; + + /* Get the Frame Length of the received packet: subtract 4 + * bytes of the CRC + */ + + dev->d_len = ((rxdesc->rdes0 & ETH_RDES0_FL_MASK) >> ETH_RDES0_FL_SHIFT) - 4; + + /* Get a buffer from the free list. We don't even check if + * this is successful because we already assure the free + * list is not empty above. + */ + + buffer = lpc43_allocbuffer(priv); + + /* Take the buffer from the RX descriptor of the first free + * segment, put it into the uIP device structure, then replace + * the buffer in the RX descriptor with the newly allocated + * buffer. + */ + + DEBUGASSERT(dev->d_buf == NULL); + dev->d_buf = (uint8_t*)rxcurr->rdes2; + rxcurr->rdes2 = (uint32_t)buffer; + + /* Return success, remembering where we should re-start scanning + * and resetting the segment scanning logic + */ + + priv->rxhead = (struct eth_rxdesc_s*)rxdesc->rdes3; + lpc43_freesegment(priv, rxcurr, priv->segments); + + nllvdbg("rxhead: %p d_buf: %p d_len: %d\n", + priv->rxhead, dev->d_buf, dev->d_len); + + return OK; + } + else + { + /* Drop the frame that contains the errors, reset the segment + * scanning logic, and continue scanning with the next frame. + */ + + nlldbg("DROPPED: RX descriptor errors: %08x\n", rxdesc->rdes0); + lpc43_freesegment(priv, rxcurr, priv->segments); + } + } + + /* Try the next descriptor */ + + rxdesc = (struct eth_rxdesc_s*)rxdesc->rdes3; + } + + /* We get here after all of the descriptors have been scanned or when rxdesc points + * to the first descriptor owned by the DMA. Remember where we left off. + */ + + priv->rxhead = rxdesc; + + nllvdbg("rxhead: %p rxcurr: %p segments: %d\n", + priv->rxhead, priv->rxcurr, priv->segments); + + return -EAGAIN; +} + +/**************************************************************************** + * Function: lpc43_receive + * + * Description: + * An interrupt was received indicating the availability of a new RX packet + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by interrupt handling logic. + * + ****************************************************************************/ + +static void lpc43_receive(FAR struct lpc43_ethmac_s *priv) +{ + struct net_driver_s *dev = &priv->dev; + + /* Loop while while lpc43_recvframe() successfully retrieves valid + * Ethernet frames. + */ + + while (lpc43_recvframe(priv) == OK) + { +#ifdef CONFIG_NET_PKT + /* When packet sockets are enabled, feed the frame into the packet tap */ + + pkt_input(&priv->dev); +#endif + + /* Check if the packet is a valid size for the uIP buffer configuration + * (this should not happen) + */ + + if (dev->d_len > CONFIG_NET_ETH_MTU) + { + nlldbg("DROPPED: Too big: %d\n", dev->d_len); + /* Free dropped packet buffer */ + + if (dev->d_buf) + { + lpc43_freebuffer(priv, dev->d_buf); + dev->d_buf = NULL; + dev->d_len = 0; + } + + continue; + } + +#ifdef CONFIG_NET_PKT + /* When packet sockets are enabled, feed the frame into the packet tap */ + + pkt_input(&priv->dev); +#endif + + /* We only accept IP packets of the configured type and ARP packets */ + +#ifdef CONFIG_NET_IPv4 + if (BUF->type == HTONS(ETHTYPE_IP)) + { + nllvdbg("IPv4 frame\n"); + + /* Handle ARP on input then give the IPv4 packet to the network + * layer + */ + + arp_ipin(&priv->dev); + ipv4_input(&priv->dev); + + /* If the above function invocation resulted in data that should be + * sent out on the network, the field d_len will set to a value > 0. + */ + + if (priv->dev.d_len > 0) + { + /* Update the Ethernet header with the correct MAC address */ + +#ifdef CONFIG_NET_IPv6 + if (IFF_IS_IPv4(priv->dev.d_flags)) +#endif + { + arp_out(&priv->dev); + } +#ifdef CONFIG_NET_IPv6 + else + { + neighbor_out(&priv->dev); + } +#endif + + /* And send the packet */ + + lpc43_transmit(priv); + } + } + else +#endif +#ifdef CONFIG_NET_IPv6 + if (BUF->type == HTONS(ETHTYPE_IP6)) + { + nllvdbg("Iv6 frame\n"); + + /* Give the IPv6 packet to the network layer */ + + ipv6_input(&priv->dev); + + /* If the above function invocation resulted in data that should be + * sent out on the network, the field d_len will set to a value > 0. + */ + + if (priv->dev.d_len > 0) + { + /* Update the Ethernet header with the correct MAC address */ + +#ifdef CONFIG_NET_IPv4 + if (IFF_IS_IPv4(priv->dev.d_flags)) + { + arp_out(&priv->dev); + } + else +#endif +#ifdef CONFIG_NET_IPv6 + { + neighbor_out(&priv->dev); + } +#endif + + /* And send the packet */ + + lpc43_transmit(priv); + } + } + else +#endif +#ifdef CONFIG_NET_ARP + if (BUF->type == htons(ETHTYPE_ARP)) + { + nllvdbg("ARP frame\n"); + + /* Handle ARP packet */ + + arp_arpin(&priv->dev); + + /* If the above function invocation resulted in data that should be + * sent out on the network, the field d_len will set to a value > 0. + */ + + if (priv->dev.d_len > 0) + { + lpc43_transmit(priv); + } + } + else +#endif + { + nlldbg("DROPPED: Unknown type: %04x\n", BUF->type); + } + + /* We are finished with the RX buffer. NOTE: If the buffer is + * re-used for transmission, the dev->d_buf field will have been + * nullified. + */ + + if (dev->d_buf) + { + /* Free the receive packet buffer */ + + lpc43_freebuffer(priv, dev->d_buf); + dev->d_buf = NULL; + dev->d_len = 0; + } + } +} + +/**************************************************************************** + * Function: lpc43_freeframe + * + * Description: + * Scans the TX descriptors and frees the buffers of completed TX transfers. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None. + * + * Assumptions: + * Global interrupts are disabled by interrupt handling logic. + * + ****************************************************************************/ + +static void lpc43_freeframe(FAR struct lpc43_ethmac_s *priv) +{ + struct eth_txdesc_s *txdesc; + int i; + + nllvdbg("txhead: %p txtail: %p inflight: %d\n", + priv->txhead, priv->txtail, priv->inflight); + + /* Scan for "in-flight" descriptors owned by the CPU */ + + txdesc = priv->txtail; + if (txdesc) + { + DEBUGASSERT(priv->inflight > 0); + + for (i = 0; (txdesc->tdes0 & ETH_TDES0_OWN) == 0; i++) + { + /* There should be a buffer assigned to all in-flight + * TX descriptors. + */ + + nllvdbg("txtail: %p tdes0: %08x tdes2: %08x tdes3: %08x\n", + txdesc, txdesc->tdes0, txdesc->tdes2, txdesc->tdes3); + + DEBUGASSERT(txdesc->tdes2 != 0); + + /* Check if this is the first segment of a TX frame. */ + + if ((txdesc->tdes0 & ETH_TDES0_FS) != 0) + { + /* Yes.. Free the buffer */ + + lpc43_freebuffer(priv, (uint8_t*)txdesc->tdes2); + } + + /* In any event, make sure that TDES2 is nullified. */ + + txdesc->tdes2 = 0; + + /* Check if this is the last segment of a TX frame */ + + if ((txdesc->tdes0 & ETH_TDES0_LS) != 0) + { + /* Yes.. Decrement the number of frames "in-flight". */ + + priv->inflight--; + + /* If all of the TX descriptors were in-flight, then RX interrupts + * may have been disabled... we can re-enable them now. + */ + + lpc43_enableint(priv, ETH_DMAINT_RI); + + /* If there are no more frames in-flight, then bail. */ + + if (priv->inflight <= 0) + { + priv->txtail = NULL; + priv->inflight = 0; + return; + } + } + + /* Try the next descriptor in the TX chain */ + + txdesc = (struct eth_txdesc_s*)txdesc->tdes3; + } + + /* We get here if (1) there are still frames "in-flight". Remember + * where we left off. + */ + + priv->txtail = txdesc; + + nllvdbg("txhead: %p txtail: %p inflight: %d\n", + priv->txhead, priv->txtail, priv->inflight); + } +} + +/**************************************************************************** + * Function: lpc43_txdone + * + * Description: + * An interrupt was received indicating that the last TX packet(s) is done + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by the watchdog logic. + * + ****************************************************************************/ + +static void lpc43_txdone(FAR struct lpc43_ethmac_s *priv) +{ + DEBUGASSERT(priv->txtail != NULL); + + /* Scan the TX descriptor change, returning buffers to free list */ + + lpc43_freeframe(priv); + + /* If no further xmits are pending, then cancel the TX timeout */ + + if (priv->inflight <= 0) + { + wd_cancel(priv->txtimeout); + + /* And disable further TX interrupts. */ + + lpc43_disableint(priv, ETH_DMAINT_TI); + } + + /* Then poll uIP for new XMIT data */ + + lpc43_dopoll(priv); +} + +/**************************************************************************** + * Function: lpc43_interrupt_process + * + * Description: + * Interrupt processing. This may be performed either within the interrupt + * handler or on the worker thread, depending upon the configuration + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Ethernet interrupts are disabled + * + ****************************************************************************/ + +static inline void lpc43_interrupt_process(FAR struct lpc43_ethmac_s *priv) +{ + uint32_t dmasr; + + /* Get the DMA interrupt status bits (no MAC interrupts are expected) */ + + dmasr = lpc43_getreg(LPC43_ETH_DMASTAT); + + /* Mask only enabled interrupts. This depends on the fact that the interrupt + * related bits (0-16) correspond in these two registers. + */ + + dmasr &= lpc43_getreg(LPC43_ETH_DMAINTEN); + + /* Check if there are pending "normal" interrupts */ + + if ((dmasr & ETH_DMAINT_NIS) != 0) + { + /* Yes.. Check if we received an incoming packet, if so, call + * lpc43_receive() + */ + + if ((dmasr & ETH_DMAINT_RI) != 0) + { + /* Clear the pending receive interrupt */ + + lpc43_putreg(ETH_DMAINT_RI, LPC43_ETH_DMASTAT); + + /* Handle the received package */ + + lpc43_receive(priv); + } + + /* Check if a packet transmission just completed. If so, call + * lpc43_txdone(). This may disable further TX interrupts if there + * are no pending tansmissions. + */ + + if ((dmasr & ETH_DMAINT_TI) != 0) + { + /* Clear the pending receive interrupt */ + + lpc43_putreg(ETH_DMAINT_TI, LPC43_ETH_DMASTAT); + + /* Check if there are pending transmissions */ + + lpc43_txdone(priv); + } + + /* Clear the pending normal summary interrupt */ + + lpc43_putreg(ETH_DMAINT_NIS, LPC43_ETH_DMASTAT); + } + + /* Handle error interrupt only if CONFIG_DEBUG_NET is eanbled */ + +#ifdef CONFIG_DEBUG_NET + + /* Check if there are pending "abnormal" interrupts */ + + if ((dmasr & ETH_DMAINT_AIS) != 0) + { + /* Just let the user know what happened */ + + nlldbg("Abnormal event(s): %08x\n", dmasr); + + /* Clear all pending abnormal events */ + + lpc43_putreg(ETH_DMAINT_ABNORMAL, LPC43_ETH_DMASTAT); + + /* Clear the pending abnormal summary interrupt */ + + lpc43_putreg(ETH_DMAINT_AIS, LPC43_ETH_DMASTAT); + } +#endif +} + +/**************************************************************************** + * Function: lpc43_interrupt_work + * + * Description: + * Perform interrupt related work from the worker thread + * + * Parameters: + * arg - The argument passed when work_queue() was called. + * + * Returned Value: + * OK on success + * + * Assumptions: + * Ethernet interrupts are disabled + * + ****************************************************************************/ + +#ifdef CONFIG_NET_NOINTS +static void lpc43_interrupt_work(FAR void *arg) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)arg; + net_lock_t state; + + DEBUGASSERT(priv); + + /* Process pending Ethernet interrupts */ + + state = net_lock(); + lpc43_interrupt_process(priv); + net_unlock(state); + + /* Re-enable Ethernet interrupts at the NVIC */ + + up_enable_irq(LPC43M4_IRQ_ETHERNET); +} +#endif + +/**************************************************************************** + * Function: lpc43_interrupt + * + * Description: + * Hardware interrupt handler + * + * Parameters: + * irq - Number of the IRQ that generated the interrupt + * context - Interrupt register state save info (architecture-specific) + * + * Returned Value: + * OK on success + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_interrupt(int irq, FAR void *context) +{ + FAR struct lpc43_ethmac_s *priv = &g_lpc43ethmac; + +#ifdef CONFIG_NET_NOINTS + uint32_t dmasr; + + /* Get the DMA interrupt status bits (no MAC interrupts are expected) */ + + dmasr = lpc43_getreg(LPC43_ETH_DMASTAT); + if (dmasr != 0) + { + /* Disable further Ethernet interrupts. Because Ethernet interrupts + * are also disabled if the TX timeout event occurs, there can be no + * race condition here. + */ + + up_disable_irq(LPC43M4_IRQ_ETHERNET); + + /* Check if a packet transmission just completed. */ + + if ((dmasr & ETH_DMAINT_TI) != 0) + { + /* If a TX transfer just completed, then cancel the TX timeout so + * there will be no race condition between any subsequent timeout + * expiration and the deferred interrupt processing. + */ + + wd_cancel(priv->txtimeout); + } + + /* Cancel any pending poll work */ + + work_cancel(HPWORK, &priv->work); + + /* Schedule to perform the interrupt processing on the worker thread. */ + + work_queue(HPWORK, &priv->work, lpc43_interrupt_work, priv, 0); + } + +#else + /* Process the interrupt now */ + + lpc43_interrupt_process(priv); +#endif + + return OK; +} + +/**************************************************************************** + * Function: lpc43_txtimeout_process + * + * Description: + * Process a TX timeout. Called from the either the watchdog timer + * expiration logic or from the worker thread, depending upon the + * configuration. The timeout means that the last TX never completed. + * Reset the hardware and start again. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by the watchdog logic. + * + ****************************************************************************/ + +static inline void lpc43_txtimeout_process(FAR struct lpc43_ethmac_s *priv) +{ + /* Then reset the hardware. Just take the interface down, then back + * up again. + */ + + lpc43_ifdown(&priv->dev); + lpc43_ifup(&priv->dev); + + /* Then poll uIP for new XMIT data */ + + lpc43_dopoll(priv); +} + +/**************************************************************************** + * Function: lpc43_txtimeout_work + * + * Description: + * Perform TX timeout related work from the worker thread + * + * Parameters: + * arg - The argument passed when work_queue() as called. + * + * Returned Value: + * OK on success + * + * Assumptions: + * Ethernet interrupts are disabled + * + ****************************************************************************/ + +#ifdef CONFIG_NET_NOINTS +static void lpc43_txtimeout_work(FAR void *arg) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)arg; + net_lock_t state; + + /* Process pending Ethernet interrupts */ + + state = net_lock(); + lpc43_txtimeout_process(priv); + net_unlock(state); +} +#endif + +/**************************************************************************** + * Function: lpc43_txtimeout_expiry + * + * Description: + * Our TX watchdog timed out. Called from the timer interrupt handler. + * The last TX never completed. Reset the hardware and start again. + * + * Parameters: + * argc - The number of available arguments + * arg - The first argument + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by the watchdog logic. + * + ****************************************************************************/ + +static void lpc43_txtimeout_expiry(int argc, uint32_t arg, ...) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)arg; + + nlldbg("Timeout!\n"); + +#ifdef CONFIG_NET_NOINTS + /* Disable further Ethernet interrupts. This will prevent some race + * conditions with interrupt work. There is still a potential race + * condition with interrupt work that is already queued and in progress. + * + * Interrupts will be re-enabled when lpc43_ifup() is called. + */ + + up_disable_irq(STM32_IRQ_ETH); + + /* Cancel any pending poll or interrupt work. This will have no effect + * on work that has already been started. + */ + + work_cancel(HPWORK, &priv->work); + + /* Schedule to perform the TX timeout processing on the worker thread. */ + + work_queue(HPWORK, &priv->work, lpc43_txtimeout_work, priv, 0); + +#else + /* Process the timeout now */ + + lpc43_txtimeout_process(priv); +#endif +} + +/**************************************************************************** + * Function: lpc43_poll_process + * + * Description: + * Perform the periodic poll. This may be called either from watchdog + * timer logic or from the worker thread, depending upon the configuration. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +static inline void lpc43_poll_process(FAR struct lpc43_ethmac_s *priv) +{ + FAR struct net_driver_s *dev = &priv->dev; + + /* Check if the next TX descriptor is owned by the Ethernet DMA or CPU. We + * cannot perform the timer poll if we are unable to accept another packet + * for transmission. Hmmm.. might be bug here. Does this mean if there is + * a transmit in progress, we will miss TCP time state updates? + * + * In a race condition, ETH_TDES0_OWN may be cleared BUT still not available + * because lpc43_freeframe() has not yet run. If lpc43_freeframe() has run, + * the buffer1 pointer (tdes2) will be nullified (and inflight should be < + * CONFIG_LPC43_ETH_NTXDESC). + */ + + if ((priv->txhead->tdes0 & ETH_TDES0_OWN) == 0 && + priv->txhead->tdes2 == 0) + { + /* If we have the descriptor, then perform the timer poll. Allocate a + * buffer for the poll. + */ + + DEBUGASSERT(dev->d_len == 0 && dev->d_buf == NULL); + dev->d_buf = lpc43_allocbuffer(priv); + + /* We can't poll if we have no buffers */ + + if (dev->d_buf) + { + /* Update TCP timing states and poll for new XMIT data. + */ + + (void)devif_timer(dev, lpc43_txpoll, LPC43_POLLHSEC); + + /* We will, most likely end up with a buffer to be freed. But it + * might not be the same one that we allocated above. + */ + + if (dev->d_buf) + { + DEBUGASSERT(dev->d_len == 0); + lpc43_freebuffer(priv, dev->d_buf); + dev->d_buf = NULL; + } + } + } + + /* Setup the watchdog poll timer again */ + + (void)wd_start(priv->txpoll, LPC43_WDDELAY, lpc43_poll_expiry, 1, priv); +} + +/**************************************************************************** + * Function: lpc43_poll_work + * + * Description: + * Perform periodic polling from the worker thread + * + * Parameters: + * arg - The argument passed when work_queue() as called. + * + * Returned Value: + * OK on success + * + * Assumptions: + * Ethernet interrupts are disabled + * + ****************************************************************************/ + +#ifdef CONFIG_NET_NOINTS +static void lpc43_poll_work(FAR void *arg) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)arg; + net_lock_t state; + + /* Perform the poll */ + + state = net_lock(); + lpc43_poll_process(priv); + net_unlock(state); +} +#endif + +/**************************************************************************** + * Function: lpc43_poll_expiry + * + * Description: + * Periodic timer handler. Called from the timer interrupt handler. + * + * Parameters: + * argc - The number of available arguments + * arg - The first argument + * + * Returned Value: + * None + * + * Assumptions: + * Global interrupts are disabled by the watchdog logic. + * + ****************************************************************************/ + +static void lpc43_poll_expiry(int argc, uint32_t arg, ...) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)arg; + +#ifdef CONFIG_NET_NOINTS + /* Is our single work structure available? It may not be if there are + * pending interrupt actions. + */ + + if (work_available(&priv->work)) + { + /* Schedule to perform the interrupt processing on the worker thread. */ + + work_queue(HPWORK, &priv->work, lpc43_poll_work, priv, 0); + } + else + { + /* No.. Just re-start the watchdog poll timer, missing one polling + * cycle. + */ + + (void)wd_start(priv->txpoll, LPC43_WDDELAY, lpc43_poll_expiry, 1, + (uint32_t)priv); + } + +#else + /* Process the interrupt now */ + + lpc43_poll_process(priv); +#endif +} + +/**************************************************************************** + * Function: lpc43_ifup + * + * Description: + * NuttX Callback: Bring up the Ethernet interface when an IP address is + * provided + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_ifup(struct net_driver_s *dev) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)dev->d_private; + int ret; + +#ifdef CONFIG_NET_IPv4 + ndbg("Bringing up: %d.%d.%d.%d\n", + dev->d_ipaddr & 0xff, (dev->d_ipaddr >> 8) & 0xff, + (dev->d_ipaddr >> 16) & 0xff, dev->d_ipaddr >> 24); +#endif +#ifdef CONFIG_NET_IPv6 + ndbg("Bringing up: %04x:%04x:%04x:%04x:%04x:%04x:%04x:%04x\n", + dev->d_ipv6addr[0], dev->d_ipv6addr[1], dev->d_ipv6addr[2], + dev->d_ipv6addr[3], dev->d_ipv6addr[4], dev->d_ipv6addr[5], + dev->d_ipv6addr[6], dev->d_ipv6addr[7]); +#endif + + /* Configure the Ethernet interface for DMA operation. */ + + ret = lpc43_ethconfig(priv); + if (ret < 0) + { + return ret; + } + + /* Set and activate a timer process */ + + (void)wd_start(priv->txpoll, LPC43_WDDELAY, lpc43_poll_expiry, 1, + (uint32_t)priv); + + /* Enable the Ethernet interrupt */ + + priv->ifup = true; + up_enable_irq(LPC43M4_IRQ_ETHERNET); + + lpc43_checksetup(); + return OK; +} + +/**************************************************************************** + * Function: lpc43_ifdown + * + * Description: + * NuttX Callback: Stop the interface. + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_ifdown(struct net_driver_s *dev) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)dev->d_private; + irqstate_t flags; + + ndbg("Taking the network down\n"); + + /* Disable the Ethernet interrupt */ + + flags = irqsave(); + up_disable_irq(LPC43M4_IRQ_ETHERNET); + + /* Cancel the TX poll timer and TX timeout timers */ + + wd_cancel(priv->txpoll); + wd_cancel(priv->txtimeout); + + /* Put the EMAC in its reset, non-operational state. This should be + * a known configuration that will guarantee the lpc43_ifup() always + * successfully brings the interface back up. + */ + + lpc43_ethreset(priv); + + /* Mark the device "down" */ + + priv->ifup = false; + irqrestore(flags); + return OK; +} + +/**************************************************************************** + * Function: lpc43_txavail_process + * + * Description: + * Perform an out-of-cycle poll. + * + * Parameters: + * priv - Reference to the NuttX driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Called in normal user mode + * + ****************************************************************************/ + +static inline void lpc43_txavail_process(FAR struct lpc43_ethmac_s *priv) +{ + nvdbg("ifup: %d\n", priv->ifup); + + /* Ignore the notification if the interface is not yet up */ + + if (priv->ifup) + { + /* Poll for new XMIT data */ + + lpc43_dopoll(priv); + } +} + +/**************************************************************************** + * Function: lpc43_txavail_work + * + * Description: + * Perform an out-of-cycle poll on the worker thread. + * + * Parameters: + * arg - Reference to the NuttX driver state structure (cast to void*) + * + * Returned Value: + * None + * + * Assumptions: + * Called on the higher priority worker thread. + * + ****************************************************************************/ + +#ifdef CONFIG_NET_NOINTS +static void lpc43_txavail_work(FAR void *arg) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)arg; + net_lock_t state; + + /* Perform the poll */ + + state = net_lock(); + lpc43_txavail_process(priv); + net_unlock(state); +} +#endif + +/**************************************************************************** + * Function: lpc43_txavail + * + * Description: + * Driver callback invoked when new TX data is available. This is a + * stimulus perform an out-of-cycle poll and, thereby, reduce the TX + * latency. + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * Called in normal user mode + * + ****************************************************************************/ + +static int lpc43_txavail(struct net_driver_s *dev) +{ + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)dev->d_private; + +#ifdef CONFIG_NET_NOINTS + /* Is our single work structure available? It may not be if there are + * pending interrupt actions and we will have to ignore the Tx + * availability action. + */ + + if (work_available(&priv->work)) + { + /* Schedule to serialize the poll on the worker thread. */ + + work_queue(HPWORK, &priv->work, lpc43_txavail_work, priv, 0); + } + +#else + irqstate_t flags; + + /* Disable interrupts because this function may be called from interrupt + * level processing. + */ + + flags = irqsave(); + + /* Perform the out-of-cycle poll now */ + + lpc43_txavail_process(priv); + irqrestore(flags); + #endif + + return OK; +} + +/**************************************************************************** + * Function: lpc43_calcethcrc + * + * Description: + * Function to calculate the CRC used by LPC43 to check an Ethernet frame + * + * Parameters: + * data - the data to be checked + * length - length of the data + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +#if defined(CONFIG_NET_IGMP) || defined(CONFIG_NET_ICMPv6) +static uint32_t lpc43_calcethcrc(const uint8_t *data, size_t length) +{ + uint32_t crc = 0xffffffff; + size_t i; + int j; + + for (i = 0; i < length; i++) + { + for (j = 0; j < 8; j++) + { + if (((crc >> 31) ^ (data[i] >> j)) & 0x01) + { + /* x^26+x^23+x^22+x^16+x^12+x^11+x^10+x^8+x^7+x^5+x^4+x^2+x+1 */ + crc = (crc << 1) ^ 0x04c11db7; + } + else + { + crc = crc << 1; + } + } + } + + return ~crc; +} +#endif + +/**************************************************************************** + * Function: lpc43_addmac + * + * Description: + * NuttX Callback: Add the specified MAC address to the hardware multicast + * address filtering + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * mac - The MAC address to be added + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +#if defined(CONFIG_NET_IGMP) || defined(CONFIG_NET_ICMPv6) +static int lpc43_addmac(struct net_driver_s *dev, FAR const uint8_t *mac) +{ + uint32_t crc; + uint32_t hashindex; + uint32_t temp; + uint32_t registeraddress; + + nllvdbg("MAC: %02x:%02x:%02x:%02x:%02x:%02x\n", + mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); + + /* Add the MAC address to the hardware multicast hash table */ + + crc = lpc43_calcethcrc( mac, 6 ); + + hashindex = (crc >> 26) & 0x3F; + + if (hashindex > 31) + { + registeraddress = LPC43_ETH_MACHTHI; + hashindex -= 32; + } + else + { + registeraddress = LPC43_ETH_MACHTLO; + } + + temp = lpc43_getreg(registeraddress); + temp |= 1 << hashindex; + lpc43_putreg(temp, registeraddress); + + temp = lpc43_getreg(LPC43_ETH_MACFFLT); + temp |= (ETH_MACFFLT_HM | ETH_MACFFLT_HPF); + lpc43_putreg(temp, LPC43_ETH_MACFFLT); + + return OK; +} +#endif + +/**************************************************************************** + * Function: lpc43_rmmac + * + * Description: + * NuttX Callback: Remove the specified MAC address from the hardware multicast + * address filtering + * + * Parameters: + * dev - Reference to the NuttX driver state structure + * mac - The MAC address to be removed + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +#ifdef CONFIG_NET_IGMP +static int lpc43_rmmac(struct net_driver_s *dev, FAR const uint8_t *mac) +{ + uint32_t crc; + uint32_t hashindex; + uint32_t temp; + uint32_t registeraddress; + + nllvdbg("MAC: %02x:%02x:%02x:%02x:%02x:%02x\n", + mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); + + /* Remove the MAC address to the hardware multicast hash table */ + + crc = lpc43_calcethcrc( mac, 6 ); + + hashindex = (crc >> 26) & 0x3F; + + if (hashindex > 31) + { + registeraddress = LPC43_ETH_MACHTHI; + hashindex -= 32; + } + else + { + registeraddress = LPC43_ETH_MACHTLO; + } + + temp = lpc43_getreg(registeraddress); + temp &= ~(1 << hashindex); + lpc43_putreg(temp, registeraddress); + + /* If there is no address registered any more, delete multicast filtering */ + + if (lpc43_getreg(LPC43_ETH_MACHTHI ) == 0 && + lpc43_getreg(LPC43_ETH_MACHTLO) == 0) + { + temp = lpc43_getreg(LPC43_ETH_MACFFLT); + temp &= ~(ETH_MACFFLT_HM | ETH_MACFFLT_HPF); + lpc43_putreg(temp, LPC43_ETH_MACFFLT); + } + + return OK; +} +#endif + +/**************************************************************************** + * Function: lpc43_txdescinit + * + * Description: + * Initializes the DMA TX descriptors in chain mode. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +static void lpc43_txdescinit(FAR struct lpc43_ethmac_s *priv) +{ + struct eth_txdesc_s *txdesc; + int i; + + /* priv->txhead will point to the first, available TX descriptor in the chain. + * Set the priv->txhead pointer to the first descriptor in the table. + */ + + priv->txhead = priv->txtable; + + /* priv->txtail will point to the first segment of the oldest pending + * "in-flight" TX transfer. NULL means that there are no active TX + * transfers. + */ + + priv->txtail = NULL; + priv->inflight = 0; + + /* Initialize each TX descriptor */ + + for (i = 0; i < CONFIG_LPC43_ETH_NTXDESC; i++) + { + txdesc = &priv->txtable[i]; + + /* Set Second Address Chained bit */ + + txdesc->tdes0 = ETH_TDES0_TCH; + +#ifdef CHECKSUM_BY_HARDWARE + /* Enable the checksum insertion for the TX frames */ + + txdesc->tdes0 |= ETH_TDES0_CIC_ALL; +#endif + + /* Clear Buffer1 address pointer (buffers will be assigned as they + * are used) + */ + + txdesc->tdes2 = 0; + + /* Initialize the next descriptor with the Next Descriptor Polling Enable */ + + if (i < (CONFIG_LPC43_ETH_NTXDESC-1)) + { + /* Set next descriptor address register with next descriptor base + * address + */ + + txdesc->tdes3 = (uint32_t)&priv->txtable[i+1]; + } + else + { + /* For last descriptor, set next descriptor address register equal + * to the first descriptor base address + */ + + txdesc->tdes3 = (uint32_t)priv->txtable; + } + } + + /* Set Transmit Desciptor List Address Register */ + + lpc43_putreg((uint32_t)priv->txtable, LPC43_ETH_DMATXDLA); +} + +/**************************************************************************** + * Function: lpc43_rxdescinit + * + * Description: + * Initializes the DMA RX descriptors in chain mode. + * + * Parameters: + * priv - Reference to the driver state structure + * + * Returned Value: + * None + * + * Assumptions: + * + ****************************************************************************/ + +static void lpc43_rxdescinit(FAR struct lpc43_ethmac_s *priv) +{ + struct eth_rxdesc_s *rxdesc; + int i; + + /* priv->rxhead will point to the first, RX descriptor in the chain. + * This will be where we receive the first incomplete frame. + */ + + priv->rxhead = priv->rxtable; + + /* If we accumulate the frame in segments, priv->rxcurr points to the + * RX descriptor of the first segment in the current TX frame. + */ + + priv->rxcurr = NULL; + priv->segments = 0; + + /* Initialize each TX descriptor */ + + for (i = 0; i < CONFIG_LPC43_ETH_NRXDESC; i++) + { + rxdesc = &priv->rxtable[i]; + + /* Set Own bit of the RX descriptor rdes0 */ + + rxdesc->rdes0 = ETH_RDES0_OWN; + + /* Set Buffer1 size and Second Address Chained bit and enabled DMA + * RX desc receive interrupt + */ + + rxdesc->rdes1 = ETH_RDES1_RCH | (uint32_t)CONFIG_LPC43_ETH_BUFSIZE; + + /* Set Buffer1 address pointer */ + + rxdesc->rdes2 = (uint32_t)&priv->rxbuffer[i*CONFIG_LPC43_ETH_BUFSIZE]; + + /* Initialize the next descriptor with the Next Descriptor Polling Enable */ + + if (i < (CONFIG_LPC43_ETH_NRXDESC-1)) + { + /* Set next descriptor address register with next descriptor base + * address + */ + + rxdesc->rdes3 = (uint32_t)&priv->rxtable[i+1]; + } + else + { + /* For last descriptor, set next descriptor address register equal + * to the first descriptor base address + */ + + rxdesc->rdes3 = (uint32_t)priv->rxtable; + } + } + + /* Set Receive Descriptor List Address Register */ + + lpc43_putreg((uint32_t)priv->rxtable, LPC43_ETH_DMARXDLA); +} + +/**************************************************************************** + * Function: lpc43_ioctl + * + * Description: + * Executes the SIOCxMIIxxx command and responds using the request struct + * that must be provided as its 2nd parameter. + * + * When called with SIOCGMIIPHY it will get the PHY address for the device + * and write it to the req->phy_id field of the request struct. + * + * When called with SIOCGMIIREG it will read a register of the PHY that is + * specified using the req->reg_no struct field and then write its output + * to the req->val_out field. + * + * When called with SIOCSMIIREG it will write to a register of the PHY that + * is specified using the req->reg_no struct field and use req->val_in as + * its input. + * + * Parameters: + * dev - Ethernet device structure + * cmd - SIOCxMIIxxx command code + * arg - Request structure also used to return values + * + * Returned Value: Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +#ifdef CONFIG_NETDEV_PHY_IOCTL +static int lpc43_ioctl(struct net_driver_s *dev, int cmd, long arg) +{ +#ifdef CONFIG_ARCH_PHY_INTERRUPT + FAR struct lpc43_ethmac_s *priv = (FAR struct lpc43_ethmac_s *)dev->d_private; +#endif + int ret; + + switch (cmd) + { +#ifdef CONFIG_ARCH_PHY_INTERRUPT + case SIOCMIINOTIFY: /* Set up for PHY event notifications */ + { + struct mii_iotcl_notify_s *req = (struct mii_iotcl_notify_s *)((uintptr_t)arg); + + ret = phy_notify_subscribe(dev->d_ifname, req->pid, req->signo, req->arg); + if (ret == OK) + { + /* Enable PHY link up/down interrupts */ + + ret = lpc43_phyintenable(priv); + } + } + break; +#endif + + case SIOCGMIIPHY: /* Get MII PHY address */ + { + struct mii_ioctl_data_s *req = (struct mii_ioctl_data_s *)((uintptr_t)arg); + req->phy_id = CONFIG_LPC43_PHYADDR; + ret = OK; + } + break; + + case SIOCGMIIREG: /* Get register from MII PHY */ + { + struct mii_ioctl_data_s *req = (struct mii_ioctl_data_s *)((uintptr_t)arg); + ret = lpc43_phyread(req->phy_id, req->reg_num, &req->val_out); + } + break; + + case SIOCSMIIREG: /* Set register in MII PHY */ + { + struct mii_ioctl_data_s *req = (struct mii_ioctl_data_s *)((uintptr_t)arg); + ret = lpc43_phywrite(req->phy_id, req->reg_num, req->val_in); + } + break; + + default: + ret = -ENOTTY; + break; + } + + return ret; +} +#endif /* CONFIG_NETDEV_PHY_IOCTL */ + +/**************************************************************************** + * Function: lpc43_phyintenable + * + * Description: +* Enable link up/down PHY interrupts. The interrupt protocol is like this: + * + * - Interrupt status is cleared when the interrupt is enabled. + * - Interrupt occurs. Interrupt is disabled (at the processor level) when + * is received. + * - Interrupt status is cleared when the interrupt is re-enabled. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * OK on success; Negated errno (-ETIMEDOUT) on failure. + * + ****************************************************************************/ + +#if defined(CONFIG_NETDEV_PHY_IOCTL) && defined(CONFIG_ARCH_PHY_INTERRUPT) +static int lpc43_phyintenable(struct lpc43_ethmac_s *priv) +{ +#warning Missing logic + return -ENOSYS; +} +#endif + +/**************************************************************************** + * Function: lpc43_phyread + * + * Description: + * Read a PHY register. + * + * Parameters: + * phydevaddr - The PHY device address + * phyregaddr - The PHY register address + * value - The location to return the 16-bit PHY register value. + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_phyread(uint16_t phydevaddr, uint16_t phyregaddr, uint16_t *value) +{ + volatile uint32_t timeout; + uint32_t regval; + + /* Configure the MACMIIAR register, preserving CSR Clock Range CR[2:0] bits */ + + regval = lpc43_getreg(LPC43_ETH_MACMIIA); + regval &= ETH_MACMIIA_CR_MASK; + + /* Set the PHY device address, PHY register address, and set the buy bit. + * the ETH_MACMIIA_WR is clear, indicating a read operation. + */ + + regval |= (((uint32_t)phydevaddr << ETH_MACMIIA_PA_SHIFT) & ETH_MACMIIA_PA_MASK); + regval |= (((uint32_t)phyregaddr << ETH_MACMIIA_MR_SHIFT) & ETH_MACMIIA_MR_MASK); + regval |= ETH_MACMIIA_GB; + + lpc43_putreg(regval, LPC43_ETH_MACMIIA); + + /* Wait for the transfer to complete */ + + for (timeout = 0; timeout < PHY_READ_TIMEOUT; timeout++) + { + if ((lpc43_getreg(LPC43_ETH_MACMIIA) & ETH_MACMIIA_GB) == 0) + { + *value = (uint16_t)lpc43_getreg(LPC43_ETH_MACMIID); + return OK; + } + } + + ndbg("MII transfer timed out: phydevaddr: %04x phyregaddr: %04x\n", + phydevaddr, phyregaddr); + + return -ETIMEDOUT; +} + +/**************************************************************************** + * Function: lpc43_phywrite + * + * Description: + * Write to a PHY register. + * + * Parameters: + * phydevaddr - The PHY device address + * phyregaddr - The PHY register address + * value - The 16-bit value to write to the PHY register value. + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_phywrite(uint16_t phydevaddr, uint16_t phyregaddr, uint16_t value) +{ + volatile uint32_t timeout; + uint32_t regval; + + /* Configure the MACMIIAR register, preserving CSR Clock Range CR[2:0] bits */ + + regval = lpc43_getreg(LPC43_ETH_MACMIIA); + regval &= ETH_MACMIIA_CR_MASK; + + /* Set the PHY device address, PHY register address, and set the busy bit. + * the ETH_MACMIIA_WR is set, indicating a write operation. + */ + + regval |= (((uint32_t)phydevaddr << ETH_MACMIIA_PA_SHIFT) & ETH_MACMIIA_PA_MASK); + regval |= (((uint32_t)phyregaddr << ETH_MACMIIA_MR_SHIFT) & ETH_MACMIIA_MR_MASK); + regval |= (ETH_MACMIIA_GB | ETH_MACMIIA_WR); + + /* Write the value into the MACIIDR register before setting the new MACMIIAR + * register value. + */ + + lpc43_putreg(value, LPC43_ETH_MACMIID); + lpc43_putreg(regval, LPC43_ETH_MACMIIA); + + /* Wait for the transfer to complete */ + + for (timeout = 0; timeout < PHY_WRITE_TIMEOUT; timeout++) + { + if ((lpc43_getreg(LPC43_ETH_MACMIIA) & ETH_MACMIIA_GB) == 0) + { + return OK; + } + } + + ndbg("MII transfer timed out: phydevaddr: %04x phyregaddr: %04x value: %04x\n", + phydevaddr, phyregaddr, value); + + return -ETIMEDOUT; +} + +/**************************************************************************** + * Function: lpc43_dm9161 + * + * Description: + * Special workaround for the Davicom DM9161 PHY is required. On power, + * up, the PHY is not usually configured correctly but will work after + * a powered-up reset. This is really a workaround for some more + * fundamental issue with the PHY clocking initialization, but the + * root cause has not been studied (nor will it be with this workaround). + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * None + * + ****************************************************************************/ + +#ifdef CONFIG_ETH0_PHY_DM9161 +static inline int lpc43_dm9161(FAR struct lpc43_ethmac_s *priv) +{ + uint16_t phyval; + int ret; + + /* Read the PHYID1 register; A failure to read the PHY ID is one + * indication that check if the DM9161 PHY CHIP is not ready. + */ + + ret = lpc43_phyread(CONFIG_LPC43_PHYADDR, MII_PHYID1, &phyval); + if (ret < 0) + { + ndbg("Failed to read the PHY ID1: %d\n", ret); + return ret; + } + + /* If we failed to read the PHY ID1 register, the reset the MCU to recover */ + + else if (phyval == 0xffff) + { + up_systemreset(); + } + + nvdbg("PHY ID1: 0x%04X\n", phyval); + + /* Now check the "DAVICOM Specified Configuration Register (DSCR)", Register 16 */ + + ret = lpc43_phyread(CONFIG_LPC43_PHYADDR, 16, &phyval); + if (ret < 0) + { + ndbg("Failed to read the PHY Register 0x10: %d\n", ret); + return ret; + } + + /* Bit 8 of the DSCR register is zero, then the DM9161 has not selected RMII. + * If RMII is not selected, then reset the MCU to recover. + */ + + else if ((phyval & (1 << 8)) == 0) + { + up_systemreset(); + } + + return OK; +} +#endif + +/**************************************************************************** + * Function: lpc43_phyinit + * + * Description: + * Configure the PHY and determine the link speed/duplex. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_phyinit(FAR struct lpc43_ethmac_s *priv) +{ + volatile uint32_t timeout; + uint32_t regval; + uint16_t phyval; + int ret; + + /* Assume 10MBps and half duplex */ + + priv->mbps100 = 0; + priv->fduplex = 0; + + /* Setup up PHY clocking by setting the SR field in the MACMIIAR register */ + + regval = lpc43_getreg(LPC43_ETH_MACMIIA); + regval &= ~ETH_MACMIIA_CR_MASK; + regval |= ETH_MACMIIA_CR; + lpc43_putreg(regval, LPC43_ETH_MACMIIA); + + /* Put the PHY in reset mode */ + + ret = lpc43_phywrite(CONFIG_LPC43_PHYADDR, MII_MCR, MII_MCR_RESET); + if (ret < 0) + { + ndbg("Failed to reset the PHY: %d\n", ret); + return ret; + } + + up_mdelay(PHY_RESET_DELAY); + +#ifdef CONFIG_LPC43_PHYINIT + /* Perform any necessary, board-specific PHY initialization */ + + ret = lpc43_phy_boardinitialize(0); + if (ret < 0) + { + ndbg("Failed to initialize the PHY: %d\n", ret); + return ret; + } +#endif + +#ifdef CONFIG_ETH0_PHY_DM9161 + /* Special workaround for the Davicom DM9161 PHY is required. */ + + ret = lpc43_dm9161(priv); + if (ret < 0) + { + return ret; + } +#endif + + /* Perform auto-negotion if so configured */ + +#ifdef CONFIG_LPC43_AUTONEG + /* Wait for link status */ + + for (timeout = 0; timeout < PHY_RETRY_TIMEOUT; timeout++) + { + ret = lpc43_phyread(CONFIG_LPC43_PHYADDR, MII_MSR, &phyval); + if (ret < 0) + { + ndbg("Failed to read the PHY MSR: %d\n", ret); + return ret; + } + else if ((phyval & MII_MSR_LINKSTATUS) != 0) + { + break; + } + } + + if (timeout >= PHY_RETRY_TIMEOUT) + { + ndbg("Timed out waiting for link status: %04x\n", phyval); + return -ETIMEDOUT; + } + + /* Enable auto-negotiation */ + + ret = lpc43_phywrite(CONFIG_LPC43_PHYADDR, MII_MCR, MII_MCR_ANENABLE); + if (ret < 0) + { + ndbg("Failed to enable auto-negotiation: %d\n", ret); + return ret; + } + + /* Wait until auto-negotiation completes */ + + for (timeout = 0; timeout < PHY_RETRY_TIMEOUT; timeout++) + { + ret = lpc43_phyread(CONFIG_LPC43_PHYADDR, MII_MSR, &phyval); + if (ret < 0) + { + ndbg("Failed to read the PHY MSR: %d\n", ret); + return ret; + } + else if ((phyval & MII_MSR_ANEGCOMPLETE) != 0) + { + break; + } + } + + if (timeout >= PHY_RETRY_TIMEOUT) + { + ndbg("Timed out waiting for auto-negotiation\n"); + return -ETIMEDOUT; + } + + /* Read the result of the auto-negotiation from the PHY-specific register */ + + ret = lpc43_phyread(CONFIG_LPC43_PHYADDR, CONFIG_LPC43_PHYSR, &phyval); + if (ret < 0) + { + ndbg("Failed to read PHY status register\n"); + return ret; + } + + /* Remember the selected speed and duplex modes */ + + nvdbg("PHYSR[%d]: %04x\n", CONFIG_LPC43_PHYSR, phyval); + + /* Different PHYs present speed and mode information in different ways. IF + * This CONFIG_LPC43_PHYSR_ALTCONFIG is selected, this indicates that the PHY + * represents speed and mode information are combined, for example, with + * separate bits for 10HD, 100HD, 10FD and 100FD. + */ + +#ifdef CONFIG_LPC43_PHYSR_ALTCONFIG + switch (phyval & CONFIG_LPC43_PHYSR_ALTMODE) + { + default: + case CONFIG_LPC43_PHYSR_10HD: + priv->fduplex = 0; + priv->mbps100 = 0; + break; + + case CONFIG_LPC43_PHYSR_100HD: + priv->fduplex = 0; + priv->mbps100 = 1; + break; + + case CONFIG_LPC43_PHYSR_10FD: + priv->fduplex = 1; + priv->mbps100 = 0; + break; + + case CONFIG_LPC43_PHYSR_100FD: + priv->fduplex = 1; + priv->mbps100 = 1; + break; + } + + /* Different PHYs present speed and mode information in different ways. Some + * will present separate information for speed and mode (this is the default). + * Those PHYs, for example, may provide a 10/100 Mbps indication and a separate + * full/half duplex indication. + */ + +#else + if ((phyval & CONFIG_LPC43_PHYSR_MODE) == CONFIG_LPC43_PHYSR_FULLDUPLEX) + { + priv->fduplex = 1; + } + + if ((phyval & CONFIG_LPC43_PHYSR_SPEED) == CONFIG_LPC43_PHYSR_100MBPS) + { + priv->mbps100 = 1; + } +#endif + +#else /* Auto-negotion not selected */ + + phyval = 0; +#ifdef CONFIG_LPC43_ETHFD + phyval |= MII_MCR_FULLDPLX; +#endif +#ifdef CONFIG_LPC43_ETH100MBPS + phyval |= MII_MCR_SPEED100; +#endif + + ret = lpc43_phywrite(CONFIG_LPC43_PHYADDR, MII_MCR, phyval); + if (ret < 0) + { + ndbg("Failed to write the PHY MCR: %d\n", ret); + return ret; + } + up_mdelay(PHY_CONFIG_DELAY); + + /* Remember the selected speed and duplex modes */ + +#ifdef CONFIG_LPC43_ETHFD + priv->fduplex = 1; +#endif +#ifdef CONFIG_LPC43_ETH100MBPS + priv->mbps100 = 1; +#endif +#endif + + ndbg("Duplex: %s Speed: %d MBps\n", + priv->fduplex ? "FULL" : "HALF", + priv->mbps100 ? 100 : 10); + + return OK; +} + +/************************************************************************************ + * Name: lpc43_selectmii + * + * Description: + * Selects the MII inteface. + * + * Input Parameters: + * None + * + * Returned Value: + * None + * + ************************************************************************************/ + +#ifdef CONFIG_LPC43_MII +static inline void lpc43_selectmii(void) +{ + uint32_t regval; + + regval = getreg32(LPC43_CREG6); + regval &= ~SYSCFG_PMC_MII_RMII_SEL; + putreg32(regval, LPC43_CREG6); +} +#endif + +/************************************************************************************ + * Name: lpc43_selectrmii + * + * Description: + * Selects the RMII inteface. + * + * Input Parameters: + * None + * + * Returned Value: + * None + * + ************************************************************************************/ + +static inline void lpc43_selectrmii(void) +{ + uint32_t regval; + + regval = getreg32(LPC43_CREG6); + regval |= CREG6_ETHMODE_RMII; + putreg32(regval, LPC43_CREG6); +} + +/**************************************************************************** + * Function: lpc43_ethgpioconfig + * + * Description: + * Configure GPIOs for the Ethernet interface. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * None. + * + * Assumptions: + * + ****************************************************************************/ + +static inline void lpc43_ethgpioconfig(FAR struct lpc43_ethmac_s *priv) +{ + /* Configure GPIO pins to support Ethernet */ + +#if defined(CONFIG_LPC43_MII) || defined(CONFIG_LPC43_RMII) + /* MDC and MDIO are common to both modes */ + + lpc43_pin_config(PINCONF_ENET_MDC); + lpc43_pin_config(PINCONF_ENET_MDIO); + + /* Set up the MII interface */ + +#if defined(CONFIG_LPC43_MII) + /* Select the MII interface */ + + lpc43_selectmii(); + + /* MII interface pins (17): + * + * MII_TX_CLK, MII_TXD[3:0], MII_TX_EN, MII_RX_CLK, MII_RXD[3:0], MII_RX_ER, + * MII_RX_DV, MII_CRS, MII_COL, MDC, MDIO + */ + + lpc43_pin_config(GPIO_ETH_MII_COL); + lpc43_pin_config(GPIO_ETH_MII_CRS); + lpc43_pin_config(GPIO_ETH_MII_RXD0); + lpc43_pin_config(GPIO_ETH_MII_RXD1); + lpc43_pin_config(GPIO_ETH_MII_RXD2); + lpc43_pin_config(GPIO_ETH_MII_RXD3); + lpc43_pin_config(GPIO_ETH_MII_RX_CLK); + lpc43_pin_config(GPIO_ETH_MII_RX_DV); + lpc43_pin_config(GPIO_ETH_MII_RX_ER); + lpc43_pin_config(GPIO_ETH_MII_TXD0); + lpc43_pin_config(GPIO_ETH_MII_TXD1); + lpc43_pin_config(GPIO_ETH_MII_TXD2); + lpc43_pin_config(GPIO_ETH_MII_TXD3); + lpc43_pin_config(GPIO_ETH_MII_TX_CLK); + lpc43_pin_config(GPIO_ETH_MII_TX_EN); + + /* Set up the RMII interface. */ + +#elif defined(CONFIG_LPC43_RMII) + /* Select the RMII interface */ + + lpc43_selectrmii(); + + /* RMII interface pins (7): + * + * RMII_TXD[1:0], RMII_TX_EN, RMII_RXD[1:0], RMII_CRS_DV, MDC, MDIO, + * RMII_REF_CLK + */ + + lpc43_pin_config(PINCONF_ENET_RX_DV); + lpc43_pin_config(PINCONF_ENET_REF_CLK); + lpc43_pin_config(PINCONF_ENET_RXD0); + lpc43_pin_config(PINCONF_ENET_RXD1); + lpc43_pin_config(PINCONF_ENET_TXD0); + lpc43_pin_config(PINCONF_ENET_TXD1); + lpc43_pin_config(PINCONF_ENET_TXEN); + +#endif +#endif +} + +/**************************************************************************** + * Function: lpc43_ethreset + * + * Description: + * Reset the Ethernet block. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * None. + * + * Assumptions: + * + ****************************************************************************/ + +static void lpc43_ethreset(FAR struct lpc43_ethmac_s *priv) +{ + uint32_t regval; + + /* Reset the Ethernet */ + + lpc43_putreg(RGU_CTRL0_ETHERNET_RST, LPC43_RGU_CTRL0); + + /* Perform a software reset by setting the SR bit in the DMABMR register. + * This Resets all MAC subsystem internal registers and logic. After this + * reset all the registers holds their reset values. + */ + + regval = lpc43_getreg(LPC43_ETH_DMABMODE); + regval |= ETH_DMABMODE_SWR; + lpc43_putreg(regval, LPC43_ETH_DMABMODE); + + /* Wait for software reset to complete. The SR bit is cleared automatically + * after the reset operation has completed in all of the core clock domains. + */ + + while ((lpc43_getreg(LPC43_ETH_DMABMODE) & ETH_DMABMODE_SWR) != 0); +} + +/**************************************************************************** + * Function: lpc43_macconfig + * + * Description: + * Configure the Ethernet MAC for DMA operation. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_macconfig(FAR struct lpc43_ethmac_s *priv) +{ + uint32_t regval; + + /* Set up the MACCR register */ + + regval = lpc43_getreg(LPC43_ETH_MACCR); + regval &= ~MACCR_CLEAR_BITS; + regval |= MACCR_SET_BITS; + + if (priv->fduplex) + { + /* Set the DM bit for full duplex support */ + + regval |= ETH_MACCFG_DM; + } + + if (priv->mbps100) + { + /* Set the FES bit for 100Mbps fast ethernet support */ + + regval |= ETH_MACCFG_FES; + } + + lpc43_putreg(regval, LPC43_ETH_MACCR); + + /* Set up the MACFFR register */ + + regval = lpc43_getreg(LPC43_ETH_MACFFLT); + regval &= ~MACFFR_CLEAR_BITS; + regval |= MACFFR_SET_BITS; + lpc43_putreg(regval, LPC43_ETH_MACFFLT); + + /* Set up the MACHTHR and MACHTLR registers */ + + lpc43_putreg(0, LPC43_ETH_MACHTHI); + lpc43_putreg(0, LPC43_ETH_MACHTLO); + + /* Setup up the MACFCR register */ + + regval = lpc43_getreg(LPC43_ETH_MACFC); + regval &= ~MACFCR_CLEAR_MASK; + regval |= MACFCR_SET_MASK; + lpc43_putreg(regval, LPC43_ETH_MACFC); + + /* Setup up the MACVLANTR register */ + + lpc43_putreg(0, LPC43_ETH_MACVLANT); + + /* DMA Configuration */ + /* Set up the DMAOMR register */ + + regval = lpc43_getreg(LPC43_ETH_DMAOPMODE); + regval &= ~DMAOMR_CLEAR_MASK; + regval |= DMAOMR_SET_MASK; + lpc43_putreg(regval, LPC43_ETH_DMAOPMODE); + + /* Set up the DMABMR register */ + + regval = lpc43_getreg(LPC43_ETH_DMABMODE); + regval &= ~DMABMR_CLEAR_MASK; + regval |= DMABMR_SET_MASK; + lpc43_putreg(regval, LPC43_ETH_DMABMODE); + + return OK; +} + +/**************************************************************************** + * Function: lpc43_macaddress + * + * Description: + * Configure the selected MAC address. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +static void lpc43_macaddress(FAR struct lpc43_ethmac_s *priv) +{ + FAR struct net_driver_s *dev = &priv->dev; + uint32_t regval; + + nllvdbg("%s MAC: %02x:%02x:%02x:%02x:%02x:%02x\n", + dev->d_ifname, + dev->d_mac.ether_addr_octet[0], dev->d_mac.ether_addr_octet[1], + dev->d_mac.ether_addr_octet[2], dev->d_mac.ether_addr_octet[3], + dev->d_mac.ether_addr_octet[4], dev->d_mac.ether_addr_octet[5]); + + /* Set the MAC address high register */ + + regval = ((uint32_t)dev->d_mac.ether_addr_octet[5] << 8) | + (uint32_t)dev->d_mac.ether_addr_octet[4]; + lpc43_putreg(regval, LPC43_ETH_MACA0HI); + + /* Set the MAC address low register */ + + regval = ((uint32_t)dev->d_mac.ether_addr_octet[3] << 24) | + ((uint32_t)dev->d_mac.ether_addr_octet[2] << 16) | + ((uint32_t)dev->d_mac.ether_addr_octet[1] << 8) | + (uint32_t)dev->d_mac.ether_addr_octet[0]; + lpc43_putreg(regval, LPC43_ETH_MACA0LO); +} + +/**************************************************************************** + * Function: lpc43_ipv6multicast + * + * Description: + * Configure the IPv6 multicast MAC address. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +#ifdef CONFIG_NET_ICMPv6 +static void lpc43_ipv6multicast(FAR struct lpc43_ethmac_s *priv) +{ + struct net_driver_s *dev; + uint16_t tmp16; + uint8_t mac[6]; + + /* For ICMPv6, we need to add the IPv6 multicast address + * + * For IPv6 multicast addresses, the Ethernet MAC is derived by + * the four low-order octets OR'ed with the MAC 33:33:00:00:00:00, + * so for example the IPv6 address FF02:DEAD:BEEF::1:3 would map + * to the Ethernet MAC address 33:33:00:01:00:03. + * + * NOTES: This appears correct for the ICMPv6 Router Solicitation + * Message, but the ICMPv6 Neighbor Solicitation message seems to + * use 33:33:ff:01:00:03. + */ + + mac[0] = 0x33; + mac[1] = 0x33; + + dev = &priv->dev; + tmp16 = dev->d_ipv6addr[6]; + mac[2] = 0xff; + mac[3] = tmp16 >> 8; + + tmp16 = dev->d_ipv6addr[7]; + mac[4] = tmp16 & 0xff; + mac[5] = tmp16 >> 8; + + nvdbg("IPv6 Multicast: %02x:%02x:%02x:%02x:%02x:%02x\n", + mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); + + (void)lpc43_addmac(dev, mac); + +#ifdef CONFIG_NET_ICMPv6_AUTOCONF + /* Add the IPv6 all link-local nodes Ethernet address. This is the + * address that we expect to receive ICMPv6 Router Advertisement + * packets. + */ + + (void)lpc43_addmac(dev, g_ipv6_ethallnodes.ether_addr_octet); + +#endif /* CONFIG_NET_ICMPv6_AUTOCONF */ +#ifdef CONFIG_NET_ICMPv6_ROUTER + /* Add the IPv6 all link-local routers Ethernet address. This is the + * address that we expect to receive ICMPv6 Router Solicitation + * packets. + */ + + (void)lpc43_addmac(dev, g_ipv6_ethallrouters.ether_addr_octet); + +#endif /* CONFIG_NET_ICMPv6_ROUTER */ +} +#endif /* CONFIG_NET_ICMPv6 */ + +/**************************************************************************** + * Function: lpc43_macenable + * + * Description: + * Enable normal MAC operation. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_macenable(FAR struct lpc43_ethmac_s *priv) +{ + uint32_t regval; + + /* Set the MAC address */ + + lpc43_macaddress(priv); + +#ifdef CONFIG_NET_ICMPv6 + /* Set up the IPv6 multicast address */ + + lpc43_ipv6multicast(priv); +#endif + + /* Enable transmit state machine of the MAC for transmission on the MII */ + + regval = lpc43_getreg(LPC43_ETH_MACCR); + regval |= ETH_MACCFG_TE; + lpc43_putreg(regval, LPC43_ETH_MACCR); + + /* Flush Transmit FIFO */ + + regval = lpc43_getreg(LPC43_ETH_DMAOPMODE); + regval |= ETH_DMAOPMODE_FTF; + lpc43_putreg(regval, LPC43_ETH_DMAOPMODE); + + /* Enable receive state machine of the MAC for reception from the MII */ + + /* Enables or disables the MAC reception. */ + + regval = lpc43_getreg(LPC43_ETH_MACCR); + regval |= ETH_MACCFG_RE; + lpc43_putreg(regval, LPC43_ETH_MACCR); + + /* Start DMA transmission */ + + regval = lpc43_getreg(LPC43_ETH_DMAOPMODE); + regval |= ETH_DMAOPMODE_ST; + lpc43_putreg(regval, LPC43_ETH_DMAOPMODE); + + /* Start DMA reception */ + + regval = lpc43_getreg(LPC43_ETH_DMAOPMODE); + regval |= ETH_DMAOPMODE_SR; + lpc43_putreg(regval, LPC43_ETH_DMAOPMODE); + + /* Enable Ethernet DMA interrupts. + * + * The LPC43 hardware supports two interrupts: (1) one dedicated to normal + * Ethernet operations and the other, used only for the Ethernet wakeup + * event. The wake-up interrupt is not used by this driver. + * + * The first Ethernet vector is reserved for interrupts generated by the + * MAC and the DMA. The MAC provides PMT and time stamp trigger interrupts, + * neither of which are used by this driver. + */ + + lpc43_putreg(ETH_MACIM_ALLINTS, LPC43_ETH_MACIM); + + /* Ethernet DMA supports two classes of interrupts: Normal interrupt + * summary (NIS) and Abnormal interrupt summary (AIS) with a variety + * individual normal and abnormal interrupting events. Here only + * the normal receive event is enabled (unless DEBUG is enabled). Transmit + * events will only be enabled when a transmit interrupt is expected. + */ + + lpc43_putreg((ETH_DMAINT_RECV_ENABLE | ETH_DMAINT_ERROR_ENABLE), + LPC43_ETH_DMAINTEN); + return OK; +} + +/**************************************************************************** + * Function: lpc43_ethconfig + * + * Description: + * Configure the Ethernet interface for DMA operation. + * + * Parameters: + * priv - A reference to the private driver state structure + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +static int lpc43_ethconfig(FAR struct lpc43_ethmac_s *priv) +{ + int ret; + + /* NOTE: The Ethernet clocks were initialized early in the boot-up + * sequence in lpc43_rcc.c. + */ + + /* Reset the Ethernet block */ + + nllvdbg("Reset the Ethernet block\n"); + lpc43_ethreset(priv); + + /* Initialize the PHY */ + + nllvdbg("Initialize the PHY\n"); + ret = lpc43_phyinit(priv); + if (ret < 0) + { + return ret; + } + + /* Initialize the MAC and DMA */ + + nllvdbg("Initialize the MAC and DMA\n"); + ret = lpc43_macconfig(priv); + if (ret < 0) + { + return ret; + } + + /* Initialize the free buffer list */ + + lpc43_initbuffer(priv); + + /* Initialize TX Descriptors list: Chain Mode */ + + lpc43_txdescinit(priv); + + /* Initialize RX Descriptors list: Chain Mode */ + + lpc43_rxdescinit(priv); + + /* Enable normal MAC operation */ + + nllvdbg("Enable normal operation\n"); + return lpc43_macenable(priv); +} + +/**************************************************************************** + * Public Functions + ****************************************************************************/ + +/**************************************************************************** + * Function: lpc43_ethinitialize + * + * Description: + * Initialize the Ethernet driver for one interface. + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ****************************************************************************/ + +static inline int lpc43_ethinitialize(void) +{ + struct lpc43_ethmac_s *priv; + + /* Get the interface structure associated with this interface number. */ + + priv = &g_lpc43ethmac; + + /* Initialize the driver structure */ + + memset(priv, 0, sizeof(struct lpc43_ethmac_s)); + priv->dev.d_ifup = lpc43_ifup; /* I/F up (new IP address) callback */ + priv->dev.d_ifdown = lpc43_ifdown; /* I/F down callback */ + priv->dev.d_txavail = lpc43_txavail; /* New TX data callback */ +#ifdef CONFIG_NET_IGMP + priv->dev.d_addmac = lpc43_addmac; /* Add multicast MAC address */ + priv->dev.d_rmmac = lpc43_rmmac; /* Remove multicast MAC address */ +#endif +#ifdef CONFIG_NETDEV_PHY_IOCTL + priv->dev.d_ioctl = lpc43_ioctl; /* Support PHY ioctl() calls */ +#endif + priv->dev.d_private = (void*)&g_lpc43ethmac; /* Used to recover private state from dev */ + + /* Create a watchdog for timing polling for and timing of transmisstions */ + + priv->txpoll = wd_create(); /* Create periodic poll timer */ + priv->txtimeout = wd_create(); /* Create TX timeout timer */ + + /* Configure GPIO pins to support Ethernet */ + + lpc43_ethgpioconfig(priv); + + /* Attach the IRQ to the driver */ + + if (irq_attach(LPC43M4_IRQ_ETHERNET, lpc43_interrupt)) + { + /* We could not attach the ISR to the interrupt */ + + return -EAGAIN; + } + + /* Put the interface in the down state. */ + + lpc43_ifdown(&priv->dev); + + /* Register the device with the OS so that socket IOCTLs can be performed */ + + (void)netdev_register(&priv->dev, NET_LL_ETHERNET); + return OK; +} + +/**************************************************************************** + * Function: up_netinitialize + * + * Description: + * This is the "standard" network initialization logic called from the + * low-level initialization logic in up_initialize.c. + * + * Parameters: + * None. + * + * Returned Value: + * None. + * + * Assumptions: + * + ****************************************************************************/ + +void up_netinitialize(void) +{ + (void)lpc43_ethinitialize(); +} + +#endif /* CONFIG_NET && CONFIG_LPC43_ETHERNET */ diff --git a/arch/arm/src/lpc43xx/lpc43_ethernet.h b/arch/arm/src/lpc43xx/lpc43_ethernet.h new file mode 100644 index 0000000000..55888fc727 --- /dev/null +++ b/arch/arm/src/lpc43xx/lpc43_ethernet.h @@ -0,0 +1,93 @@ +/************************************************************************************ + * arch/arm/src/lpc43xx/lpc43_eth.h + * + * Copyright (C) 2009-2015 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ************************************************************************************/ + +#ifndef __ARCH_ARM_SRC_LPC43XX_LPC43_ETH_H +#define __ARCH_ARM_SRC_LPC43XX_LPC43_ETH_H + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +#include + +#include "chip.h" + +#include "chip/lpc43_ethernet.h" + +#ifndef __ASSEMBLY__ + +/************************************************************************************ + * Public Functions + ************************************************************************************/ + +#undef EXTERN +#if defined(__cplusplus) +#define EXTERN extern "C" +extern "C" { +#else +#define EXTERN extern +#endif + +/************************************************************************************ + * Function: lpc43_phy_boardinitialize + * + * Description: + * Some boards require specialized initialization of the PHY before it can be used. + * This may include such things as configuring GPIOs, resetting the PHY, etc. If + * CONFIG_LPC43_PHYINIT is defined in the configuration then the board specific + * logic must provide lpc43_phyinitialize(); The LPC43 Ethernet driver will call + * this function one time before it first uses the PHY. + * + * Parameters: + * intf - Always zero for now. + * + * Returned Value: + * OK on success; Negated errno on failure. + * + * Assumptions: + * + ************************************************************************************/ + +#ifdef CONFIG_LPC43_PHYINIT +int lpc43_phy_boardinitialize(int intf); +#endif + +#undef EXTERN +#if defined(__cplusplus) +} +#endif + +#endif /* __ASSEMBLY__ */ +#endif /* __ARCH_ARM_SRC_LPC43XX_LPC43_ETH_H */