STM32F746G-DISCO: Add a network-enabled NSH configuratino for network testing
This commit is contained in:
Gregory Nutt
parent
4cb2464e77
commit
ba105349a4
@ -489,9 +489,20 @@ Configurations
|
||||
Configuration Directories
|
||||
-------------------------
|
||||
|
||||
netnsh:
|
||||
------
|
||||
This is a NetShell (NSH) very similar to the nsh configuration described
|
||||
below. It differs in that it has networking enabled.
|
||||
|
||||
NOTES:
|
||||
|
||||
1. Both IPv4 and IPv6 protocoals are enabled.
|
||||
|
||||
2. UDP, TCIP/IP, ARP, ICMP, and ICMPv6 are also enabled.
|
||||
|
||||
nsh:
|
||||
---
|
||||
Configures the NuttShell (nsh) located at apps/examples/nsh. The
|
||||
Configures the NuttShell (NSH) located at apps/examples/nsh. The
|
||||
Configuration enables the serial interfaces on UART6. Support for
|
||||
builtin applications is enabled, but in the base configuration no
|
||||
builtin applications are selected.
|
||||
|
||||
@ -264,15 +264,12 @@
|
||||
#define LED_PANIC 3 /* LD1=flashing */
|
||||
|
||||
/* Button definitions ***************************************************************/
|
||||
/* Pushbutton B1, labelled "User", is connected to GPIO PI11. A high
|
||||
value will be sensed when the button is depressed.
|
||||
|
||||
/* The STM32F7 Discovery supports one button: */
|
||||
/* The STM32F7 Discovery supports one button: Pushbutton B1, labelled "User", is
|
||||
* connected to GPIO PI11. A high value will be sensed when the button is depressed.
|
||||
*/
|
||||
|
||||
#define BUTTON_USER 0
|
||||
|
||||
#define NUM_BUTTONS 1
|
||||
|
||||
#define BUTTON_USER_BIT (1 << BUTTON_USER)
|
||||
|
||||
/* Alternate function pin selections ************************************************/
|
||||
@ -294,6 +291,28 @@
|
||||
#define GPIO_USART6_RX GPIO_USART6_RX_1
|
||||
#define GPIO_USART6_TX GPIO_USART6_TX_1
|
||||
|
||||
/* The STM32 F7 connects to a SMSC LAN8742A PHY using these pins:
|
||||
* STM32 F7 BOARD LAN8742A
|
||||
* GPIO SIGNAL PIN NAME
|
||||
* -------- ------------ -------------
|
||||
* PG11 RMII_TX_EN TXEN
|
||||
* PG13 RMII_TXD0 TXD0
|
||||
* PG14 RMII_TXD1 TXD1
|
||||
* PC4 RMII_RXD0 RXD0/MODE0
|
||||
* PC5 RMII_RXD1 RXD1/MODE1
|
||||
* PG2 RMII_RXER RXER/PHYAD0
|
||||
* PA7 RMII_CRS_DV CRS_DV/MODE2
|
||||
* PC1 RMII_MDC MDC
|
||||
* PA2 RMII_MDIO MDIO
|
||||
* N/A NRST nRST
|
||||
* PA1 RMII_REF_CLK nINT/REFCLK0
|
||||
* N/A OSC_25M XTAL1/CLKIN
|
||||
*/
|
||||
|
||||
#define GPIO_ETH_RMII_TX_EN GPIO_ETH_RMII_TX_EN_2
|
||||
#define GPIO_ETH_RMII_TXD0 GPIO_ETH_RMII_TXD0_2
|
||||
#define GPIO_ETH_RMII_TXD1 GPIO_ETH_RMII_TXD1_2
|
||||
|
||||
/************************************************************************************
|
||||
* Public Data
|
||||
************************************************************************************/
|
||||
|
||||
112
configs/stm32f746g-disco/netnsh/Make.defs
Normal file
112
configs/stm32f746g-disco/netnsh/Make.defs
Normal file
@ -0,0 +1,112 @@
|
||||
############################################################################
|
||||
# configs/stm32f746g-disco/netnsh/Make.defs
|
||||
#
|
||||
# Copyright (C) 2015 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include ${TOPDIR}/.config
|
||||
include ${TOPDIR}/tools/Config.mk
|
||||
include ${TOPDIR}/arch/arm/src/armv7-m/Toolchain.defs
|
||||
|
||||
LDSCRIPT = flash.ld
|
||||
|
||||
ifeq ($(WINTOOL),y)
|
||||
# Windows-native toolchains
|
||||
DIRLINK = $(TOPDIR)/tools/copydir.sh
|
||||
DIRUNLINK = $(TOPDIR)/tools/unlink.sh
|
||||
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||||
ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
|
||||
ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
|
||||
ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)}"
|
||||
else
|
||||
# Linux/Cygwin-native toolchain
|
||||
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
||||
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
||||
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
||||
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)
|
||||
endif
|
||||
|
||||
CC = $(CROSSDEV)gcc
|
||||
CXX = $(CROSSDEV)g++
|
||||
CPP = $(CROSSDEV)gcc -E
|
||||
LD = $(CROSSDEV)ld
|
||||
AR = $(ARCROSSDEV)ar rcs
|
||||
NM = $(ARCROSSDEV)nm
|
||||
OBJCOPY = $(CROSSDEV)objcopy
|
||||
OBJDUMP = $(CROSSDEV)objdump
|
||||
|
||||
ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
|
||||
ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
|
||||
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
ARCHOPTIMIZATION = -g
|
||||
endif
|
||||
|
||||
ifneq ($(CONFIG_DEBUG_NOOPT),y)
|
||||
ARCHOPTIMIZATION += $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
|
||||
endif
|
||||
|
||||
ARCHCFLAGS = -fno-builtin
|
||||
ARCHCXXFLAGS = -fno-builtin -fno-exceptions -fno-rtti
|
||||
ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
|
||||
ARCHWARNINGSXX = -Wall -Wshadow
|
||||
ARCHDEFINES =
|
||||
ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
|
||||
|
||||
CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
|
||||
AFLAGS = $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
NXFLATLDFLAGS1 = -r -d -warn-common
|
||||
NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-pcrel.ld -no-check-sections
|
||||
LDNXFLATFLAGS = -e main -s 2048
|
||||
|
||||
OBJEXT = .o
|
||||
LIBEXT = .a
|
||||
EXEEXT =
|
||||
|
||||
ifneq ($(CROSSDEV),arm-nuttx-elf-)
|
||||
LDFLAGS += -nostartfiles -nodefaultlibs
|
||||
endif
|
||||
ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
|
||||
LDFLAGS += -g
|
||||
endif
|
||||
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTINCLUDES = -I.
|
||||
HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
|
||||
HOSTLDFLAGS =
|
||||
|
||||
1103
configs/stm32f746g-disco/netnsh/defconfig
Normal file
1103
configs/stm32f746g-disco/netnsh/defconfig
Normal file
File diff suppressed because it is too large
Load Diff
77
configs/stm32f746g-disco/netnsh/setenv.sh
Normal file
77
configs/stm32f746g-disco/netnsh/setenv.sh
Normal file
@ -0,0 +1,77 @@
|
||||
#!/bin/bash
|
||||
# configs/stm32f746g-disco/netnsh/setenv.sh
|
||||
#
|
||||
# Copyright (C) 2015 Gregory Nutt. All rights reserved.
|
||||
# Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name NuttX nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
|
||||
if [ "$_" = "$0" ] ; then
|
||||
echo "You must source this script, not run it!" 1>&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
WD=`pwd`
|
||||
if [ ! -x "setenv.sh" ]; then
|
||||
echo "This script must be executed from the top-level NuttX build directory"
|
||||
exit 1
|
||||
fi
|
||||
|
||||
if [ -z "${PATH_ORIG}" ]; then
|
||||
export PATH_ORIG="${PATH}"
|
||||
fi
|
||||
|
||||
# This is the Cygwin path to the location where I installed the Atmel GCC
|
||||
# toolchain under Windows. You will also have to edit this if you install
|
||||
# this toolchain in any other location
|
||||
#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Atmel/Atmel Toolchain/ARM GCC/Native/4.7.3.99/arm-gnu-toolchain/bin"
|
||||
|
||||
# This is the Cygwin path to the location where I installed the CodeSourcery
|
||||
# toolchain under windows. You will also have to edit this if you install
|
||||
# the CodeSourcery toolchain in any other location
|
||||
#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
|
||||
#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery_CodeBench_Lite_for_ARM_EABI/bin"
|
||||
# export TOOLCHAIN_BIN="/cygdrive/c/Users/MyName/MentorGraphics/Sourcery_CodeBench_Lite_for_ARM_EABI/bin"
|
||||
|
||||
# This is the location where I installed the ARM "GNU Tools for ARM Embedded Processors"
|
||||
# You can this free toolchain here https://launchpad.net/gcc-arm-embedded
|
||||
export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/GNU Tools ARM Embedded/4.9 2014q4/bin"
|
||||
|
||||
# This is the path to the location where I installed the devkitARM toolchain
|
||||
# You can get this free toolchain from http://devkitpro.org/ or http://sourceforge.net/projects/devkitpro/
|
||||
#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/devkitARM/bin"
|
||||
|
||||
# This is the Cygwin path to the location where I build the buildroot
|
||||
# toolchain.
|
||||
# export TOOLCHAIN_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
|
||||
|
||||
# Add the path to the toolchain to the PATH varialble
|
||||
export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
|
||||
|
||||
echo "PATH : ${PATH}"
|
||||
Loading…
Reference in New Issue
Block a user