sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

SAM4E UDP: Cosmetic updates to tracing and README

Browse Source
This commit is contained in:
Gregory Nutt 2014-03-21 10:45:12 -06:00
parent b35fab2e9e
commit ba51d1d575
1 changed files with 110 additions and 73 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

183
configs/sam4e-ek/README.txt
View File

@ -22,6 +22,8 @@ Contents
- Networking Support
- AT25 Serial FLASH
- USB Full-Speed Device
- HSMCI
- Touchscreen
- SAM4E-EK-specific Configuration Options
- Configurations
@ -671,7 +673,9 @@ USB Full-Speed Device
Device Drivers -> USB Device Driver Support
CONFIG_CDCACM=y : Enable the CDC/ACM device
CONFIG_CDCACM_BULKIN_REQLEN=96 : Default request size
CONFIG_CDCACM_EPINTIN=1 : Select endpoint numbers
CONFIG_CDCACM_EPBULKOUT=2
CONFIG_CDCACM_EPBULKIN=3
The following setting enables an example that can can be used to control
the CDC/ACM device. It will add two new NSH commands:
@ -681,7 +685,15 @@ USB Full-Speed Device
/dev/ttyACM0).
Application Configuration -> Examples:
CONFIG_SYSTEM_CDCACM=y : Enable an CDC/ACM example
CONFIG_SYSTEM_CDCACM=y : Enable an CDC/ACM example
CONFIG_SYSTEM_CDCACM_DEVMINOR=0 : Use /dev/ttyUSB0
NOTE: You cannot have both the CDC/ACM and the MSC class drivers enabled
simultaneously in the way described here. If you want to use both, then
you will need to consider a USB "composite" devices that support supports
both interfaces. There are no instructures here for setting up the USB
composite device, but there are other examples in the NuttX board support
directories that can be used for reference.
Debugging USB Device
--------------------
@ -719,6 +731,81 @@ USB Full-Speed Device
serial console. However, the debug output will be asynchronous with the
trace output and, hence, difficult to interpret.
HSMCI
=====
Enabling HSMCI support. The SAM3U-KE provides a an SD memory card slot.
Support for the SD slot can be enabled with the following settings:
System Type->ATSAM3/4 Peripheral Support
CONFIG_SAM34_HSMCI=y : Enable HSMCI support
CONFIG_SAM34_DMAC0=y : DMAC support is needed by HSMCI
System Type
CONFIG_SAM34_GPIO_IRQ=y : PIO interrupts needed
CONFIG_SAM34_GPIOA_IRQ=y : Card detect pin is on PIOA
Device Drivers -> MMC/SD Driver Support
CONFIG_MMCSD=y : Enable MMC/SD support
CONFIG_MMSCD_NSLOTS=1 : One slot per driver instance
CONFIG_MMCSD_HAVECARDDETECT=y : Supports card-detect PIOs
CONFIG_MMCSD_SDIO=y : SDIO-based MMC/SD support
CONFIG_SDIO_DMA=y : Use SDIO DMA
CONFIG_SDIO_BLOCKSETUP=y : Needs to know block sizes
Library Routines
CONFIG_SCHED_WORKQUEUE=y : Driver needs work queue support
Application Configuration -> NSH Library
CONFIG_NSH_ARCHINIT=y : NSH board-initialization
Touchscreen
===========
The NSH configuration can be used to verify the ADS7843E touchscreen on
the SAM4E-EK LCD. With these modifications, you can include the touchscreen
test program at apps/examples/touchscreen as an NSH built-in application.
You can enable the touchscreen and test by modifying the default
configuration in the following ways:
Device Drivers
CONFIG_SPI=y : Enable SPI support
CONFIG_SPI_EXCHANGE=y : The exchange() method is supported
CONFIG_SPI_OWNBUS=y : Smaller code if this is the only SPI device
CONFIG_INPUT=y : Enable support for input devices
CONFIG_INPUT_ADS7843E=y : Enable support for the XPT2046
CONFIG_ADS7843E_SPIDEV=2 : Use SPI CS 2 for communication
CONFIG_ADS7843E_SPIMODE=0 : Use SPI mode 0
CONFIG_ADS7843E_FREQUENCY=1000000 : SPI BAUD 1MHz
CONFIG_ADS7843E_SWAPXY=y : If landscape orientation
CONFIG_ADS7843E_THRESHX=51 : These will probably need to be tuned
CONFIG_ADS7843E_THRESHY=39
System Type -> Peripherals:
CONFIG_SAM34_SPI0=y : Enable support for SPI
System Type:
CONFIG_GPIO_IRQ=y : GPIO interrupt support
CONFIG_GPIOA_IRQ=y : Enable GPIO interrupts from port A
RTOS Features:
CONFIG_DISABLE_SIGNALS=n : Signals are required
Library Support:
CONFIG_SCHED_WORKQUEUE=y : Work queue support required
Application Configuration:
CONFIG_EXAMPLES_TOUCHSCREEN=y : Enable the touchscreen built-in test
Defaults should be okay for related touchscreen settings. Touchscreen
debug output on UART0 can be enabled with:
Build Setup:
CONFIG_DEBUG=y : Enable debug features
CONFIG_DEBUG_VERBOSE=y : Enable verbose debug output
CONFIG_DEBUG_INPUT=y : Enable debug output from input devices
SAM4E-EK-specific Configuration Options
=======================================
@ -994,6 +1081,10 @@ Configurations
a network because additional time will be required to fail with
timeout errors.
STATUS:
2014-3-13: The basic NSH serial console is working. Network support
has been verified.
3. This configuration supports a network with fixed IP address. You
may have to change these settings for your network:
@ -1015,80 +1106,26 @@ Configurations
reconfigured (See see the configuration settings and usage notes
above in the section entitled "AT25 Serial FLASH").
5. This configuration has been used for verifying the touchscreen on
on the SAM4E-EK LCD. With these modifications, you can include the
touchscreen test program at apps/examples/touchscreen as an NSH built-in
application. You can enable the touchscreen and test by modifying the
default configuration in the following ways:
STATUS:
2014-3-14: The DMA-based SPI appears to be functional and can be used
to support a FAT file system on the AT25 Serial FLASH.
Device Drivers
CONFIG_SPI=y : Enable SPI support
CONFIG_SPI_EXCHANGE=y : The exchange() method is supported
CONFIG_SPI_OWNBUS=y : Smaller code if this is the only SPI device
5. To use USB, see the instructions above under "USB Full-Speed Device."
CONFIG_INPUT=y : Enable support for input devices
CONFIG_INPUT_ADS7843E=y : Enable support for the XPT2046
CONFIG_ADS7843E_SPIDEV=2 : Use SPI CS 2 for communication
CONFIG_ADS7843E_SPIMODE=0 : Use SPI mode 0
CONFIG_ADS7843E_FREQUENCY=1000000 : SPI BAUD 1MHz
CONFIG_ADS7843E_SWAPXY=y : If landscpe orientation
CONFIG_ADS7843E_THRESHX=51 : These will probably need to be tuned
CONFIG_ADS7843E_THRESHY=39
STATUS:
2014-3-21: USB support is under development and only partially
functional. Additional test and integration is required.
System Type -> Peripherals:
CONFIG_SAM34_SPI0=y : Enable support for SPI
6. This configuration can be used to verify the touchscreen on on the
SAM4E-EK LCD. See the instructions above in the paragraph entitled
"Touchscreen".
System Type:
CONFIG_GPIO_IRQ=y : GPIO interrupt support
CONFIG_GPIOA_IRQ=y : Enable GPIO interrupts from port A
STATUS:
2014-3-21: The touchscreen has not yet been tested.
RTOS Features:
CONFIG_DISABLE_SIGNALS=n : Signals are required
7. Enabling HSMCI support. The SAM3U-KE provides a an SD memory card
slot. Support for the SD slot can be enabled following the
instructions provided above in the paragraph entitled "HSMCI."
Library Support:
CONFIG_SCHED_WORKQUEUE=y : Work queue support required
Applicaton Configuration:
CONFIG_EXAMPLES_TOUCHSCREEN=y : Enable the touchscreen built-int test
Defaults should be okay for related touchscreen settings. Touchscreen
debug output on UART0 can be enabled with:
Build Setup:
CONFIG_DEBUG=y : Enable debug features
CONFIG_DEBUG_VERBOSE=y : Enable verbose debug output
CONFIG_DEBUG_INPUT=y : Enable debug output from input devices
6. Enabling HSMCI support. The SAM3U-KE provides a an SD memory card
slot. Support for the SD slot can be enabled with the following
settings:
System Type->ATSAM3/4 Peripheral Support
CONFIG_SAM34_HSMCI=y : Enable HSMCI support
CONFIG_SAM34_DMAC0=y : DMAC support is needed by HSMCI
System Type
CONFIG_SAM34_GPIO_IRQ=y : PIO interrupts needed
CONFIG_SAM34_GPIOA_IRQ=y : Card detect pin is on PIOA
Device Drivers -> MMC/SD Driver Support
CONFIG_MMCSD=y : Enable MMC/SD support
CONFIG_MMSCD_NSLOTS=1 : One slot per driver instance
CONFIG_MMCSD_HAVECARDDETECT=y : Supports card-detect PIOs
CONFIG_MMCSD_SDIO=y : SDIO-based MMC/SD support
CONFIG_SDIO_DMA=y : Use SDIO DMA
CONFIG_SDIO_BLOCKSETUP=y : Needs to know block sizes
Library Routines
CONFIG_SCHED_WORKQUEUE=y : Driver needs work queue support
Application Configuration -> NSH Library
CONFIG_NSH_ARCHINIT=y : NSH board-initialization
STATUS:
2014-3-13: The basic NSH serial console is working. Network support
has been verified. HSMCI and touchscreen have not been tested (the
above notes came from the SAM3U-EK and have not been yet been tested
on the SAM4E-EK).
2014-3-14: The DMA-based SPI appears to be functional and can be used
to support a FAT file system on the AT25 Serial FLASH.
STATUS:
2014-3-21: The HSMCI SD card slot has not yet been tested.