Updates for the Sure PIC32 board

configs/Kconfig

@@ -607,7 +607,6 @@ config ARCH_BOARD_MIKROE_STM32F4
 config ARCH_BOARD_SUREPIC32MX
 	bool "Sure PIC32MX boards"
 	depends on ARCH_CHIP_PIC32MX440F512H
-	select ARCH_HAVE_LEDS
 	select ARCH_HAVE_BUTTONS
 	select ARCH_HAVE_IRQBUTTONS
 	---help---

configs/arduino-due/README.txt

@@ -185,6 +185,9 @@ ITEAD 2.4" TFT with Touch
   3. Parallel data is not contiguous in the PIO register
   4. Touchcontroller /CS pin is connected to ground (always selected).
   5. Either PA28 or PC29 may drive PWM10
+  6. The schematics I have do not agree with the documentation.  The Touch IRQ
+     and Dout pins are reversed in the Documentation (D9 an D8, respectively).
+     I am assuming that the schematic is correct.
 
   SD Interface:
 

configs/sure-pic32mx/Kconfig

@@ -11,6 +11,7 @@ choice
 
 config ARCH_DBDP11215
 	bool "DB_DP11215 PIC32 Storage Demo Board"
+	select ARCH_HAVE_LEDS
 	---help---
 		DB_DP11215 PIC32 Storage Demo Board
 
@@ -34,7 +35,6 @@ config ARCH_DBDP11212
 		- 2x16 LCD display
 		- 4 digit, 8 segment LED display
 		- Three tactile switches
-		- Four user LEDs
 
 endchoice
 endif

configs/sure-pic32mx/README.txt

@@ -927,6 +927,7 @@ Where <subdir> is one of the following:
         Board Configuration:
            CONFIG_ARCH_DBDP11215=n    : Disable the DB-DP11215
            CONFIG_ARCH_DBDP11212=y    : Enable the DB-DP11212
+           CONFIG_ARCH_LEDS=n         : The DB-DP11212 has no LEDs
 
         System Type -> PIC32MX Peripheral Support:
            CONFIG_PIC32MX_UART2=n     : Disable UART2
@@ -951,7 +952,7 @@ Where <subdir> is one of the following:
           CONFIG_RAMLOG_SYSLOG=y      : This enables the RAM-based logger as the
                                         system logger.
 
-        Logging is currently can be set up to use any amount of memorym (here 8KB):
+        Logging is currently can be set up to use any amount of memory (here 8KB):
 
           CONFIG_RAMLOG_CONSOLE_BUFSIZE=8192
 

configs/sure-pic32mx/usbnsh/defconfig

@@ -401,6 +401,10 @@ CONFIG_UART2_BAUD=115200
 CONFIG_UART2_BITS=8
 CONFIG_UART2_PARITY=0
 CONFIG_UART2_2STOP=0
+# CONFIG_UART2_IFLOWCONTROL is not set
+# CONFIG_UART2_OFLOWCONTROL is not set
+# CONFIG_SERIAL_IFLOWCONTROL is not set
+# CONFIG_SERIAL_OFLOWCONTROL is not set
 CONFIG_USBDEV=y
 
 #
@@ -433,6 +437,7 @@ CONFIG_CDCACM_EPBULKIN_FSSIZE=64
 CONFIG_CDCACM_EPBULKIN_HSSIZE=512
 CONFIG_CDCACM_NWRREQS=4
 CONFIG_CDCACM_NRDREQS=4
+CONFIG_CDCACM_BULKIN_REQLEN=96
 CONFIG_CDCACM_RXBUFSIZE=256
 CONFIG_CDCACM_TXBUFSIZE=256
 CONFIG_CDCACM_VENDORID=0x0525
@@ -581,6 +586,7 @@ CONFIG_BUILTIN_PROXY_STACKSIZE=1024
 # CONFIG_EXAMPLES_MM is not set
 # CONFIG_EXAMPLES_MODBUS is not set
 # CONFIG_EXAMPLES_MOUNT is not set
+# CONFIG_EXAMPLES_NRF24L01TERM is not set
 CONFIG_EXAMPLES_NSH=y
 # CONFIG_EXAMPLES_NULL is not set
 # CONFIG_EXAMPLES_NX is not set
@@ -708,6 +714,7 @@ CONFIG_NSH_BUILTIN_APPS=y
 CONFIG_NSH_CODECS_BUFSIZE=128
 CONFIG_NSH_FILEIOSIZE=512
 CONFIG_NSH_LINELEN=64
+CONFIG_NSH_MAXARGUMENTS=6
 CONFIG_NSH_NESTDEPTH=3
 # CONFIG_NSH_DISABLESCRIPT is not set
 # CONFIG_NSH_DISABLEBG is not set
@@ -746,6 +753,11 @@ CONFIG_NSH_ARCHINIT=y
 # FLASH Erase-all Command
 #
 
+#
+# RAM test
+#
+# CONFIG_SYSTEM_RAMTEST is not set
+
 #
 # readline()
 #