Add stm3240g-eval nsh2 configuration: SDIO and no UART

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4363 42af7a65-404d-4744-a932-0658087f49c3

configs/mcu123-lpc214x/README.txt

@@ -140,6 +140,9 @@ In System Programming (ISP) Mode
    changed from high to low, the LPC214x will enter ISP (In System
    Programming) state.
 
+   J2-RST: When J2 is shorted, the reset pin of CPU is controlled by
+   the DTR signal of UART0. Short J2 to enable ISP automatic download.
+
    Alternatively, you can just press the INT1 button while resetting.
    The LEDs will be off if the LPC2148 successfully enters ISP mode.
 

configs/mcu123-lpc214x/composite/Make.defs

@@ -37,7 +37,6 @@ include ${TOPDIR}/.config
 
 # The default value for CROSSDEV can be overridden from the make command line:
 #   make                         -- Will build for the CodeSourcery toolchain
-#   make CROSSDEV=arm-elf-       -- Will build for the NuttX buildroot toolchain
 #   make CROSSDEV=arm-eabi-      -- Will build for the devkitARM toolchain
 #   make CROSSDEV=arm-none-eabi- -- Will build for the CodeSourcery toolchain
 #   make CROSSDEV=arm-elf-       -- Will build for the NuttX buildroot toolchain

configs/stm3240g-eval/README.txt

@@ -661,6 +661,33 @@ Where <subdir> is one of the following:
        CONFIG_DEBUG_CAN
        CONFIG_CAN_REGDEBUG
 
+    5. This configuration requires that jumper JP22 be set to enable RS-232 operation.
+
+  nsh2:
+  -----
+
+    This is an alternaitve NSH configuration.  One limitation of the STM3240G-EVAL
+    board is that you cannot have both a UART-based NSH console and SDIO support.
+    The nsh2 differs from the nsh configuration in the following ways:
+
+    -CONFIG_STM32_USART3=y      : USART3 is disabled
+    + CONFIG_STM32_USART3=n
+
+    -CONFIG_STM32_SDIO=n        : SDIO is enabled
+    +CONFIG_STM32_SDIO=y
+
+    Logically, that is the only difference.  There are, however, other configuration
+    differences as necessary to support this different device configuration. Just
+    the do the 'diff' if you are curious.
+
+    NOTES:
+    1. See the notes for the nsh configuration.  Most also apply to the nsh2
+       configuration.
+
+    2. RS-232 is disabled, but Telnet is still available for use as a console.
+
+    3. This configuration requires that jumper JP22 be set to enable SDIO operation.
+
   ostest:
   ------
     This configuration directory, performs a simple OS test using
@@ -669,12 +696,12 @@ Where <subdir> is one of the following:
 
     CONFIG_STM32_CODESOURCERYW=y  : CodeSourcery under Windows
 
-telnetd:
+  telnetd:
---------
+  --------
 
-  A simple test of the Telnet daemon(see apps/netutils/README.txt,
+    A simple test of the Telnet daemon(see apps/netutils/README.txt,
-  apps/examples/README.txt, and apps/examples/telnetd).  This is
+    apps/examples/README.txt, and apps/examples/telnetd).  This is
-  the same daemon that is used in the nsh configuration so if you
+    the same daemon that is used in the nsh configuration so if you
-  use NSH, then you don't care about this.  This test is good for
+    use NSH, then you don't care about this.  This test is good for
-  testing the Telnet daemon only because it works in a simpler
+    testing the Telnet daemon only because it works in a simpler
-  environment than does the nsh configuration.
+    environment than does the nsh configuration.

configs/stm3240g-eval/nsh2/Make.defs

@@ -0,0 +1,170 @@
+############################################################################
+# configs/stm3240g-eval/nsh2/Make.defs
+#
+#   Copyright (C) 2012 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+LDSCRIPT = ld.script
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh2/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh2/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions -fno-rtti
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+

configs/stm3240g-eval/nsh2/appconfig

@@ -0,0 +1,73 @@
+############################################################################
+# configs/stm3240g-eval/nsh2/appconfig
+#
+#   Copyright (C) 2012 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/nsh
+
+# The NSH application library
+
+CONFIGURED_APPS += system/readline
+CONFIGURED_APPS += nshlib
+
+# Networking libraries
+
+ifeq ($(CONFIG_NET),y)
+CONFIGURED_APPS += netutils/uiplib
+CONFIGURED_APPS += netutils/resolv
+CONFIGURED_APPS += netutils/webclient
+CONFIGURED_APPS += netutils/tftpc
+ifeq ($(CONFIG_NSH_TELNET),y)
+CONFIGURED_APPS += netutils/telnetd
+endif
+endif
+
+# Applications configured as an NX built-in commands
+
+ifeq ($(CONFIG_ADC),y)
+CONFIGURED_APPS += examples/adc
+endif
+
+ifeq ($(CONFIG_PWM),y)
+CONFIGURED_APPS += examples/pwm
+endif
+
+ifeq ($(CONFIG_CAN),y)
+CONFIGURED_APPS += examples/can
+endif
+
+ifeq ($(CONFIG_I2C),y)
+CONFIGURED_APPS += system/i2c
+endif

configs/stm3240g-eval/nsh2/ld.script

@@ -0,0 +1,116 @@
+/****************************************************************************
+ * configs/stm3240g-eval/nsh2/ld.script
+ *
+ *   Copyright (C) 2012 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 1024Kb of FLASH beginning at address 0x0800:0000 and
+ * 192Kb of SRAM. SRAM is split up into three blocks:
+ *
+ * 1) 112Kb of SRAM beginning at address 0x2000:0000
+ * 2)  16Kb of SRAM beginning at address 0x2001:c000
+ * 3)  64Kb of TCM SRAM beginning at address 0x1000:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 1024K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 112K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

configs/stm3240g-eval/nsh2/setenv.sh

@@ -0,0 +1,67 @@
+#!/bin/bash
+# configs/stm3240g-eval/nsh/setenv.sh
+#
+#   Copyright (C) 2012 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$_" = "$0" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+WD=`pwd`
+if [ ! -x "setenv.sh" ]; then
+  echo "This script must be executed from the top-level NuttX build directory"
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then
+  export PATH_ORIG="${PATH}"
+fi
+
+# This the Cygwin path to the location where I installed the RIDE
+# toolchain under windows.  You will also have to edit this if you install
+# the RIDE toolchain in any other location
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Raisonance/Ride/arm-gcc/bin"
+
+# This the Cygwin path to the location where I installed the CodeSourcery
+# toolchain under windows.  You will also have to edit this if you install
+# the CodeSourcery toolchain in any other location
+export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+
+# This the Cygwin path to the location where I build the buildroot
+# toolchain.
+#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
+
+# Add the path to the toolchain to the PATH varialble
+export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"

configs/stm3240g-eval/src/Makefile

@@ -1,7 +1,7 @@
 ############################################################################
 # configs/stm3240g-eval/src/Makefile
 #
-#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Copyright (C) 2011-2012 Gregory Nutt. All rights reserved.
 #   Author: Gregory Nutt <gnutt@nuttx.org>
 #
 # Redistribution and use in source and binary forms, with or without
@@ -64,6 +64,10 @@ ifeq ($(CONFIG_CAN),y)
 CSRCS		+= up_can.c
 endif
 
+ifeq ($(CONFIG_NSH_ARCHINIT),y)
+CSRCS		+= up_nsh.c
+endif
+
 COBJS		= $(CSRCS:.c=$(OBJEXT))
 
 SRCS		= $(ASRCS) $(CSRCS)

configs/stm3240g-eval/src/up_nsh.c

@@ -0,0 +1,208 @@
+/****************************************************************************
+ * config/stm3240g_eval/src/up_nsh.c
+ * arch/arm/src/board/up_nsh.c
+ *
+ *   Copyright (C) 2012 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <debug.h>
+#include <errno.h>
+
+#ifdef CONFIG_STM32_SPI1
+#  include <nuttx/spi.h>
+#  include <nuttx/mtd.h>
+#endif
+
+#ifdef CONFIG_STM32_SDIO
+#  include <nuttx/sdio.h>
+#  include <nuttx/mmcsd.h>
+#endif
+
+#include "stm32_internal.h"
+
+/****************************************************************************
+ * Pre-Processor Definitions
+ ****************************************************************************/
+
+/* Configuration ************************************************************/
+
+/* For now, don't build in any SPI1 support -- NSH is not using it */
+
+#undef CONFIG_STM32_SPI1
+
+/* PORT and SLOT number probably depend on the board configuration */
+
+#ifdef CONFIG_ARCH_BOARD_STM3240G_EVAL
+#  define CONFIG_NSH_HAVEUSBDEV 1
+#  define CONFIG_NSH_HAVEMMCSD  1
+#  if defined(CONFIG_NSH_MMCSDSLOTNO) && CONFIG_NSH_MMCSDSLOTNO != 0
+#    error "Only one MMC/SD slot"
+#    undef CONFIG_NSH_MMCSDSLOTNO
+#  endif
+#  ifndef CONFIG_NSH_MMCSDSLOTNO
+#    define CONFIG_NSH_MMCSDSLOTNO 0
+#  endif
+#else
+   /* Add configuration for new STM32 boards here */
+#  error "Unrecognized STM32 board"
+#  undef CONFIG_NSH_HAVEUSBDEV
+#  undef CONFIG_NSH_HAVEMMCSD
+#endif
+
+/* Can't support USB features if USB is not enabled */
+
+#ifndef CONFIG_USBDEV
+#  undef CONFIG_NSH_HAVEUSBDEV
+#endif
+
+/* Can't support MMC/SD features if mountpoints are disabled or if SDIO support
+ * is not enabled.
+ */
+
+#if defined(CONFIG_DISABLE_MOUNTPOINT) || !defined(CONFIG_STM32_SDIO)
+#  undef CONFIG_NSH_HAVEMMCSD
+#endif
+
+#ifndef CONFIG_NSH_MMCSDMINOR
+#  define CONFIG_NSH_MMCSDMINOR 0
+#endif
+
+/* Debug ********************************************************************/
+
+#ifdef CONFIG_CPP_HAVE_VARARGS
+#  ifdef CONFIG_DEBUG
+#    define message(...) lib_lowprintf(__VA_ARGS__)
+#  else
+#    define message(...) printf(__VA_ARGS__)
+#  endif
+#else
+#  ifdef CONFIG_DEBUG
+#    define message lib_lowprintf
+#  else
+#    define message printf
+#  endif
+#endif
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: nsh_archinitialize
+ *
+ * Description:
+ *   Perform architecture specific initialization
+ *
+ ****************************************************************************/
+
+int nsh_archinitialize(void)
+{
+#ifdef CONFIG_STM32_SPI1
+  FAR struct spi_dev_s *spi;
+  FAR struct mtd_dev_s *mtd;
+#endif
+#ifdef CONFIG_NSH_HAVEMMCSD
+  FAR struct sdio_dev_s *sdio;
+  int ret;
+#endif
+
+  /* Configure SPI-based devices */
+
+#ifdef CONFIG_STM32_SPI1
+  /* Get the SPI port */
+
+  message("nsh_archinitialize: Initializing SPI port 1\n");
+  spi = up_spiinitialize(1);
+  if (!spi)
+    {
+      message("nsh_archinitialize: Failed to initialize SPI port 0\n");
+      return -ENODEV;
+    }
+  message("nsh_archinitialize: Successfully initialized SPI port 0\n");
+
+  /* Now bind the SPI interface to the M25P64/128 SPI FLASH driver */
+
+  message("nsh_archinitialize: Bind SPI to the SPI flash driver\n");
+  mtd = m25p_initialize(spi);
+  if (!mtd)
+    {
+      message("nsh_archinitialize: Failed to bind SPI port 0 to the SPI FLASH driver\n");
+      return -ENODEV;
+    }
+  message("nsh_archinitialize: Successfully bound SPI port 0 to the SPI FLASH driver\n");
+#warning "Now what are we going to do with this SPI FLASH driver?"
+#endif
+
+  /* Mount the SDIO-based MMC/SD block driver */
+
+#ifdef CONFIG_NSH_HAVEMMCSD
+  /* First, get an instance of the SDIO interface */
+
+  message("nsh_archinitialize: Initializing SDIO slot %d\n",
+          CONFIG_NSH_MMCSDSLOTNO);
+  sdio = sdio_initialize(CONFIG_NSH_MMCSDSLOTNO);
+  if (!sdio)
+    {
+      message("nsh_archinitialize: Failed to initialize SDIO slot %d\n",
+              CONFIG_NSH_MMCSDSLOTNO);
+      return -ENODEV;
+    }
+
+  /* Now bind the SDIO interface to the MMC/SD driver */
+
+  message("nsh_archinitialize: Bind SDIO to the MMC/SD driver, minor=%d\n",
+          CONFIG_NSH_MMCSDMINOR);
+  ret = mmcsd_slotinitialize(CONFIG_NSH_MMCSDMINOR, sdio);
+  if (ret != OK)
+    {
+      message("nsh_archinitialize: Failed to bind SDIO to the MMC/SD driver: %d\n", ret);
+      return ret;
+    }
+  message("nsh_archinitialize: Successfully bound SDIO to the MMC/SD driver\n");
+  
+  /* Then let's guess and say that there is a card in the slot.  I need to check to
+   * see if the STM3240G-EVAL board supports a GPIO to detect if there is a card in
+   * the slot.
+   */
+
+   sdio_mediachange(sdio, true);
+#endif
+  return OK;
+}