SAMV17-XULT: Can't use UART3 when LCD is conencted, switch to USART0
This commit is contained in:
Gregory Nutt
parent
c513469300
commit
c1491b40f4
@ -152,6 +152,21 @@ use either the VCOM or an external RS-232 driver. Here are some options.
|
||||
5VO Vcc
|
||||
--------- -----------
|
||||
|
||||
- Arduino Communications. Additional UART/USART connections are available
|
||||
on the Arduino Communications connection J505:
|
||||
|
||||
------ ------ ------- ------- --------
|
||||
Pin on SAMV71 Arduino Arduino SAMV71
|
||||
J503 PIO Name Pin Function
|
||||
------ ------ ------- ------- --------
|
||||
3 PD18 RX1 0 URXD4
|
||||
4 PD19 TX1 0 UTXD4
|
||||
5 PD15 RX2 0 RXD2
|
||||
6 PD16 TX2 0 TXD2
|
||||
7 PB0 RX3 0 RXD0
|
||||
8 PB1 TX3 1 TXD0
|
||||
------ ------ ------- ------- --------
|
||||
|
||||
- SAMV7-XULT EXTn connectors. USART pins are also available the EXTn
|
||||
connectors. The following are labelled in the User Guide for USART
|
||||
functionality:
|
||||
@ -848,6 +863,22 @@ in the OFF-ON-OFF positions to select 16-bit color mode.
|
||||
50 GND - - Ground
|
||||
---- ------------ ---- -------- -----------------------------------------------------------
|
||||
|
||||
Connecting the flat cable. I was embarrassed to say that I did not know how
|
||||
the connectors worked. Let me share this so that, perhaps, I can save you
|
||||
the same embarrassment:
|
||||
|
||||
- The maXTouch Xplained Pro has an Omron XF2M-5015-1A connector. There is a
|
||||
black bar at back (toward the baord). Raise that bar and insert the cable
|
||||
with the contacts away from the board. Lower that bar to lock the cable
|
||||
in place.
|
||||
|
||||
- The SAMV71-Xult has a TE Connectivity 5-1734839-0 FPC connector that works
|
||||
differently. On each size of the connector are two small white tabs. Pull
|
||||
these out and away from the board. Insert the ribbon with the contacts
|
||||
toward the board. Lock the cable in place by pushing the tabs back in
|
||||
place.
|
||||
|
||||
|
||||
MXT Configuration Options
|
||||
-------------------------
|
||||
|
||||
@ -982,7 +1013,7 @@ NOTES:
|
||||
reconfiguration process.
|
||||
|
||||
2. Unless stated otherwise, all configurations generate console
|
||||
output on USART3 (i.e., for the Arduino serial shield).
|
||||
output on UART3 (i.e., for the Arduino serial shield).
|
||||
|
||||
3. All of these configurations are set up to build under Windows using the
|
||||
"GNU Tools for ARM Embedded Processors" that is maintained by ARM
|
||||
@ -1015,7 +1046,7 @@ NOTES:
|
||||
Configuration sub-directories
|
||||
-----------------------------
|
||||
|
||||
mxtxplned:
|
||||
mxtxplnd:
|
||||
|
||||
Configures the NuttShell (nsh) located at examples/nsh. There are three
|
||||
very similar NSH configurations:
|
||||
@ -1036,15 +1067,42 @@ Configuration sub-directories
|
||||
2. Basic touchscreen/LCD configuration settings are discussed above in
|
||||
the paragraph entitled, "maXTouch Xplained Pro".
|
||||
|
||||
3. Like the nsh configuration, this configuration has the serial console
|
||||
setup to used with an Aduino serial shield (UART3). NOTE: Use of
|
||||
EXT1 conflicts with the Arduino RXD pin (PD28). You cannot put the
|
||||
maXTouch Xplained in EXT1 and also use the Arduion RXD/TXD pins as
|
||||
your serial console.
|
||||
3. Unlike the nsh configuration, this configuration has the serial console
|
||||
setup to USART0 which is available on EXT1:
|
||||
|
||||
If you need to use EXT1, you will have to re-configure the serial
|
||||
console on a different UART/USART. The LCD (EXT4) is configured
|
||||
by default.
|
||||
----------- --- ------- -----
|
||||
Connector PIO Arduino SAMV7
|
||||
----------- --- ------- -----
|
||||
EXT1 pin 13 PB0 RX3 RXD0
|
||||
EXT1 pin 14 PB1 TX3 TXD0
|
||||
----------- --- ------- -----
|
||||
|
||||
and also on the Arduino Communications connector (J505):
|
||||
|
||||
----------- --- ------- -----
|
||||
Connector PIO Arduino SAMV7
|
||||
----------- --- ------- -----
|
||||
J505 pin 7 PB0 RX3 RXD0
|
||||
J505 pin 8 PB1 TX3 TXD0
|
||||
----------- --- ------- -----
|
||||
|
||||
Use of either the EXT1 or the LCD/EXT4 connectors conflict with the
|
||||
Arduino RXD pin (UART3, PD28). You cannot put the maXTouch Xplained
|
||||
in EXT1 or LCD/EXT4 and also use the Arduino RXD/TXD pins as your
|
||||
serial console.
|
||||
|
||||
The LCD (EXT4) is configured by default because only the RGB LCD
|
||||
interface is currently supported and that is only available on that
|
||||
connector.
|
||||
|
||||
If you plan to use EXT2 for some reason, you may re-configure the
|
||||
serial console to use UART3, the standard Arduino RXD/TXD. You
|
||||
would also, of course, have to disable the LCD.
|
||||
|
||||
NOTE that the USART0 pins PB0 and PB1 conflict with SSC TF and TK
|
||||
pins as connected to the WM8904 audio CODEC. So, unless yet a
|
||||
different U[S]ART option is selected, Audio cannot be used with
|
||||
this configuration.
|
||||
|
||||
4. Support for the ILI8488 LCD is enabled. Only the RGB mode is support
|
||||
at present. As a consequence, the maXTouch Xplained Pro must be
|
||||
|
||||
@ -290,11 +290,32 @@
|
||||
* 2 PD30 TX0 1 UTXD3
|
||||
* ------ ------ ------- ------- --------
|
||||
*
|
||||
* There are alternative pin selections only for UTXD3:
|
||||
* There are alternative pin selections only for UART3 TXD:
|
||||
*/
|
||||
|
||||
#define GPIO_UART3_TXD GPIO_UART3_TXD_1
|
||||
|
||||
|
||||
/* - Arduino Communications. Additional UART/USART connections are available
|
||||
* on the Arduino Communications connection J505:
|
||||
*
|
||||
* ------ ------ ------- ------- --------
|
||||
* Pin on SAMV71 Arduino Arduino SAMV71
|
||||
* J503 PIO Name Pin Function
|
||||
* ------ ------ ------- ------- --------
|
||||
* 3 PD18 RX1 0 URXD4
|
||||
* 4 PD19 TX1 0 UTXD4
|
||||
* 5 PD15 RX2 0 RXD2
|
||||
* 6 PD16 TX2 0 TXD2
|
||||
* 7 PB0 RX3 0 RXD0
|
||||
* 8 PB1 TX3 1 TXD0
|
||||
* ------ ------ ------- ------- --------
|
||||
*
|
||||
* There are alternative pin selections only for UART4 TXD:
|
||||
*/
|
||||
|
||||
#define GPIO_UART4_TXD GPIO_UART4_TXD_1
|
||||
|
||||
/* - SAMV7-XULT EXTn connectors. USART pins are also available the EXTn
|
||||
* connectors. The following are labelled in the User Guide for USART
|
||||
* functionality:
|
||||
|
||||
@ -222,11 +222,11 @@ CONFIG_SAMV7_TWIHS0=y
|
||||
# CONFIG_SAMV7_UART0 is not set
|
||||
# CONFIG_SAMV7_UART1 is not set
|
||||
# CONFIG_SAMV7_UART2 is not set
|
||||
CONFIG_SAMV7_UART3=y
|
||||
# CONFIG_SAMV7_UART3 is not set
|
||||
# CONFIG_SAMV7_UART4 is not set
|
||||
# CONFIG_SAMV7_USBDEVHS is not set
|
||||
# CONFIG_SAMV7_USBHOSTHS is not set
|
||||
# CONFIG_SAMV7_USART0 is not set
|
||||
CONFIG_SAMV7_USART0=y
|
||||
# CONFIG_SAMV7_USART1 is not set
|
||||
# CONFIG_SAMV7_USART2 is not set
|
||||
# CONFIG_SAMV7_WDT0 is not set
|
||||
@ -590,7 +590,7 @@ CONFIG_SERIAL=y
|
||||
# CONFIG_ARCH_HAVE_UART0 is not set
|
||||
# CONFIG_ARCH_HAVE_UART1 is not set
|
||||
# CONFIG_ARCH_HAVE_UART2 is not set
|
||||
CONFIG_ARCH_HAVE_UART3=y
|
||||
# CONFIG_ARCH_HAVE_UART3 is not set
|
||||
# CONFIG_ARCH_HAVE_UART4 is not set
|
||||
# CONFIG_ARCH_HAVE_UART5 is not set
|
||||
# CONFIG_ARCH_HAVE_UART6 is not set
|
||||
@ -598,7 +598,7 @@ CONFIG_ARCH_HAVE_UART3=y
|
||||
# CONFIG_ARCH_HAVE_UART8 is not set
|
||||
# CONFIG_ARCH_HAVE_SCI0 is not set
|
||||
# CONFIG_ARCH_HAVE_SCI1 is not set
|
||||
# CONFIG_ARCH_HAVE_USART0 is not set
|
||||
CONFIG_ARCH_HAVE_USART0=y
|
||||
# CONFIG_ARCH_HAVE_USART1 is not set
|
||||
# CONFIG_ARCH_HAVE_USART2 is not set
|
||||
# CONFIG_ARCH_HAVE_USART3 is not set
|
||||
@ -612,27 +612,28 @@ CONFIG_ARCH_HAVE_UART3=y
|
||||
#
|
||||
# USART Configuration
|
||||
#
|
||||
CONFIG_USART0_ISUART=y
|
||||
CONFIG_MCU_SERIAL=y
|
||||
CONFIG_STANDARD_SERIAL=y
|
||||
# CONFIG_SERIAL_IFLOWCONTROL is not set
|
||||
# CONFIG_SERIAL_OFLOWCONTROL is not set
|
||||
CONFIG_ARCH_HAVE_SERIAL_TERMIOS=y
|
||||
# CONFIG_SERIAL_TERMIOS is not set
|
||||
CONFIG_UART3_SERIAL_CONSOLE=y
|
||||
CONFIG_USART0_SERIAL_CONSOLE=y
|
||||
# CONFIG_OTHER_SERIAL_CONSOLE is not set
|
||||
# CONFIG_NO_SERIAL_CONSOLE is not set
|
||||
|
||||
#
|
||||
# UART3 Configuration
|
||||
# USART0 Configuration
|
||||
#
|
||||
CONFIG_UART3_RXBUFSIZE=256
|
||||
CONFIG_UART3_TXBUFSIZE=256
|
||||
CONFIG_UART3_BAUD=115200
|
||||
CONFIG_UART3_BITS=8
|
||||
CONFIG_UART3_PARITY=0
|
||||
CONFIG_UART3_2STOP=0
|
||||
# CONFIG_UART3_IFLOWCONTROL is not set
|
||||
# CONFIG_UART3_OFLOWCONTROL is not set
|
||||
CONFIG_USART0_RXBUFSIZE=256
|
||||
CONFIG_USART0_TXBUFSIZE=256
|
||||
CONFIG_USART0_BAUD=115200
|
||||
CONFIG_USART0_BITS=8
|
||||
CONFIG_USART0_PARITY=0
|
||||
CONFIG_USART0_2STOP=0
|
||||
# CONFIG_USART0_IFLOWCONTROL is not set
|
||||
# CONFIG_USART0_OFLOWCONTROL is not set
|
||||
# CONFIG_USBDEV is not set
|
||||
# CONFIG_USBHOST is not set
|
||||
# CONFIG_WIRELESS is not set
|
||||
|
||||
Loading…
Reference in New Issue
Block a user