USB config options
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@971 42af7a65-404d-4744-a932-0658087f49c3
This commit is contained in:
patacongo
parent
fcb71c37bc
commit
f0b8289e37
@ -290,6 +290,18 @@ defconfig -- This is a configuration file similar to the Linux
|
||||
CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
|
||||
USB device controller driver
|
||||
CONFIG_USBDEV - Enables USB device support
|
||||
CONFIG_USBDEV_ISOCHRONOUS - Build in extra support for isochronous
|
||||
endpoints
|
||||
CONFIG_USBDEV_DUALSPEED -Hardware handles high and full speed
|
||||
operation (USB 2.0)
|
||||
CONFIG_USBDEV_SELFPOWERED - Will cause USB features to indicate
|
||||
that the device is self-powered
|
||||
CONFIG_USBDEV_MAXPOWER - Maximum power consumption in mA
|
||||
CONFIG_USBDEV_TRACE - Enables USB tracing for debug
|
||||
CONFIG_USBDEV_TRACE_NRECORDS - Number of trace entries to remember
|
||||
|
||||
Stack and heap information
|
||||
|
||||
CONFIG_BOOT_FROM_FLASH - Some configurations support XIP
|
||||
|
||||
@ -30,11 +30,72 @@ Where <subdir> is one of the following:
|
||||
|
||||
ostest
|
||||
^^^^^^
|
||||
|
||||
This configuration directory, performs a simple OS test using
|
||||
examples/ostest.
|
||||
|
||||
nsh
|
||||
^^^
|
||||
|
||||
Configures the NuttShell (nsh) located at examples/nsh. The
|
||||
Configuration enables only the serial NSH interfaces.
|
||||
|
||||
Configuration Options
|
||||
^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
In additional to the common configuration options listed in the
|
||||
file configs/README.txt, there are other configuration options
|
||||
specific to the LPC214x:
|
||||
|
||||
CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
processor architecture.
|
||||
CONFIG_ARCH_name - for use in C code. This identifies the
|
||||
particular chip or SoC that the architecture is implemented
|
||||
in.
|
||||
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
CONFIG_ARCH_CHIP_name - For use in C code
|
||||
CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
the board that supports the particular chip or SoC.
|
||||
CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
CONFIG_ARCH_BOARD_name - for use in C code
|
||||
CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to lpc2148.
|
||||
CONFIG_DRAM_SIZE - Describes the internal DRAM.
|
||||
CONFIG_DRAM_START - The start address of internal DRAM
|
||||
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
|
||||
LPC2148 specific chip initialization
|
||||
|
||||
CONFIG_EXTMEM_MODE, CONFIG_RAM_MODE. CONFIG_CODE_BASE, CONFIG_PLL_SETUP,
|
||||
CONFIG_MAM_SETUP, CONFIG_APBDIV_SETUP, CONFIG_EMC_SETUP,. CONFIG_BCFG0_SETUP,
|
||||
CONFIG_BCFG1_SETUP, CONFIG_BCFG2_SETUP, CONFIG_BCFG3_SETUP, CONFIG_ADC_SETUP
|
||||
|
||||
LPC214X UART device driver settings
|
||||
|
||||
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||||
console and ttys0 (default is the UART0).
|
||||
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
This specific the size of the receive buffer
|
||||
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||||
being sent. This specific the size of the transmit buffer
|
||||
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity, 3=mark 1, 4=space 0
|
||||
CONFIG_UARTn_2STOP - Two stop bits
|
||||
|
||||
LPC214X USB Configuration
|
||||
|
||||
CONFIG_LPC214X_USBDEV_FRAME_INTERRUPT
|
||||
Handle USB Start-Of-Frame events.
|
||||
Enable reading SOF from interrupt handler vs. simply reading on demand.
|
||||
Probably a bad idea... Unless there is some issue with sampling the SOF
|
||||
from hardware asynchronously.
|
||||
CONFIG_LPC214X_USBDEV_EPFAST_INTERRUPT
|
||||
Enable high priority interrupts. I have no idea why you might want to
|
||||
do that
|
||||
CONFIG_LPC214X_USBDEV_NDMADESCRIPTORS
|
||||
Number of DMA descriptors to allocate in the 8Kb USB RAM. This is a
|
||||
tradeoff between the number of DMA channels that can be supported vs
|
||||
the size of the DMA buffers available.
|
||||
CONFIG_LPC214X_USBDEV_DMA
|
||||
Enable lpc214x-specific DMA support
|
||||
|
||||
@ -13,27 +13,77 @@ Where <subdir> is one of the following:
|
||||
|
||||
ostest
|
||||
^^^^^^
|
||||
|
||||
This configuration directory, performs a simple OS test using
|
||||
examples/ostest.
|
||||
|
||||
nsh
|
||||
^^^
|
||||
|
||||
Configures the NuttShell (nsh) located at examples/nsh. The
|
||||
Configuration enables both the serial and telnetd NSH interfaces.
|
||||
|
||||
nettest
|
||||
^^^^^^^
|
||||
|
||||
This alternative configuration directory may be used to
|
||||
enable networking using the OSDs DM9000A Ethernet interface.
|
||||
It uses examples/nettest to excercise the TCP/IP network.
|
||||
|
||||
uip
|
||||
^^^
|
||||
|
||||
This configuration file demonstrates the tiny webserver
|
||||
at examples/uip.
|
||||
|
||||
udp
|
||||
^^^
|
||||
|
||||
This alternative configuration directory is similar to nettest
|
||||
except that is use examples/upd to exercise UDP.
|
||||
|
||||
Configuration Options
|
||||
^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
In additional to the common configuration options listed in the
|
||||
file configs/README.txt, there are other configuration options
|
||||
specific to the DM320:
|
||||
|
||||
CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
processor architecture.
|
||||
CONFIG_ARCH_name - for use in C code. This identifies the
|
||||
particular chip or SoC that the architecture is implemented
|
||||
in.
|
||||
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
CONFIG_ARCH_CHIP_name - For use in C code
|
||||
CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
the board that supports the particular chip or SoC.
|
||||
CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
CONFIG_ARCH_BOARD_name - for use in C code
|
||||
CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to lpc2148.
|
||||
CONFIG_DRAM_SIZE - Describes the internal DRAM.
|
||||
CONFIG_DRAM_START - The start address of internal DRAM
|
||||
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
|
||||
DM320 specific device driver settings
|
||||
|
||||
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||||
console and ttys0 (default is the UART0).
|
||||
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
This specific the size of the receive buffer
|
||||
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||||
being sent. This specific the size of the transmit buffer
|
||||
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
CONFIG_UARTn_2STOP - Two stop bits
|
||||
|
||||
DM320 USB Configuration
|
||||
|
||||
CONFIG_DM320_GIO_USBATTACH
|
||||
GIO that detects USB attach/detach events
|
||||
CONFIG_DM320_GIO_USBDPPULLUP
|
||||
GIO connected to D+. Support software connect/disconnect.
|
||||
CONFIG_DMA320_USBDEV_DMA
|
||||
Enable DM320-specific DMA support
|
||||
|
||||
Loading…
Reference in New Issue
Block a user