examples/cpuhog and serialblaster from Bob Doiron

2014-04-22 07:52:08 -06:00 · 2014-04-22 07:52:08 -06:00 · f42c357654
commit f42c357654
parent ca2c794acd
3 changed files with 68 additions and 94 deletions
--- a/configs/sam4s-xplained-pro/TODO.txt
+++ b/configs/sam4s-xplained-pro/TODO.txt
@ -1,12 +1,56 @@
 - implement flash driver
   - see arch/arm/src/stm32/stm32_flash.c and related
-     - both banks could be mapped with care taken not to erase the active code. 
+     - both banks could be mapped with care taken not to erase the active code.
       - perhaps the MPU could block code corruption?
-       
-   - once implemented, the free() cmd replacement can show flash information. 
+
+   - once implemented, the free() cmd replacement can show flash information.

 - Seen crashes when running serial ports below 921600
+
+    - COM34 (UART1, ttyS1) runs the smoothest with 'serialblaster' test...
+    the other two (UART0, USART1) seem to stutter...
+
+   - created a cpuhog test. Each instance takes a semaphore, burns cpu for 6ms and then releases
+     the sem to exercises semaphores passing and a busy cpu. The first two instances become a
+     producer/consumer pair using a pipe (FIFO) to exercise the fileio data passing.
+       -> no crashes with 8 instances running. (No MMU, No BASEPRI)
+       -> no crashes with 8 instances running. (MMU + BASEPRI)
+          -> not however that the serial ports are very finicky with BASEPRI enabled!
+            This setup sends single charactes for each produced or consumed block,
+            and doesn't seem to have any issues:
+              NuttShell (NSH)
+              nsh> cpuhog > /dev/ttyS1 &
+              cpuhog [5:50]
+              nsh> cpuhog > /dev/ttyS2 &
+              cpuhog [7:50]
+              nsh> cpuhog &
+              cpuhog [8:50]
+              nsh> cpuhog 2
+              cpuhog &
+              cpuhog [9:50]
+              nsh> cpuhog 3
+              cpuhog &
+              cpuhog [10:50]
+              nsh> cpuhog 4
+              cpuhog &
+              cpuhog [11:50]
+              nsh> cpuhog 5
+
+              nsh> cpuhog &
+              cpuhog [12:50]
+              nsh> cpuhog 6
+
+              nsh> cpuhog &
+              cpuhog [13:50]
+              nsh> cpuhog 7
+
 - USB serial not quite stable when pushing lots of data
- 
+
 - UARTs don't use DMA. We may need this for high baudrates.
-   - Inbound hardware flow control requires dma. 
+   - Inbound hardware flow control requires dma.
+
+Current Test:
+
+40mA:   120Mhz (240 MHz PLL) with SDCard mounted, UART0+UART1+USART1 enabled, USB Device availible (but nothing plugged in)
+37.8mA: 120Mhz (120 MHz PLL) with SDCard mounted, UART0+UART1+USART1 enabled
+16.9mA:  "" with WFI added to up_idle()
--- a/configs/sam4s-xplained-pro/include/board.h
+++ b/configs/sam4s-xplained-pro/include/board.h
@ -135,6 +135,7 @@
 #define HSMCI_SDXFR_CLKDIV           (2 << HSMCI_MR_CLKDIV_SHIFT)
 #define HSMCI_SDWIDEXFR_CLKDIV       HSMCI_SDXFR_CLKDIV

+#ifdef CONFIG_SAM34_UDP
 /* The PLL clock (USB_48M or UDPCK) is driven from the output of the PLL,
 * PLLACK.  The PLL clock must be 48MHz.  PLLACK can be divided down via the
 * PMC USB register to provide the PLL clock.  So in order to use the USB
@ -144,8 +145,9 @@
 * PLLACK = 192MHz, USBDIV=5, USB_48M = 192 MHz / (3 + 1) = 48MHz
 */

-#define BOARD_PMC_USBS               (0)
-#define BOARD_PMC_USBDIV             (4 << PMC_USB_USBDIV_SHIFT)
+#  define BOARD_PMC_USBS             (0)
+#  define BOARD_PMC_USBDIV           (4 << PMC_USB_USBDIV_SHIFT)
+#endif

 /* FLASH wait states:
 *
--- a/configs/sam4s-xplained-pro/nsh/defconfig
+++ b/configs/sam4s-xplained-pro/nsh/defconfig
@ -50,7 +50,6 @@ CONFIG_ARCH_HAVE_STACKCHECK=y
 #
 # CONFIG_DEBUG_MM is not set
 # CONFIG_DEBUG_SCHED is not set
-# CONFIG_DEBUG_USB is not set
 # CONFIG_DEBUG_FS is not set
 # CONFIG_DEBUG_LIB is not set
 # CONFIG_DEBUG_BINFMT is not set
@ -222,7 +221,7 @@ CONFIG_SAM34_SMC=y
 # CONFIG_SAM34_TWIS1 is not set
 CONFIG_SAM34_UART0=y
 CONFIG_SAM34_UART1=y
-CONFIG_SAM34_UDP=y
+# CONFIG_SAM34_UDP is not set
 # CONFIG_SAM34_USART0 is not set
 CONFIG_SAM34_USART1=y
 CONFIG_SAM34_WDT=y
@ -250,11 +249,6 @@ CONFIG_SAM34_GPIOC_IRQ=y
 CONFIG_SAM34_HSMCI_RDPROOF=y
 CONFIG_SAM34_HSMCI_WRPROOF=y

-#
-# AT91SAM3/4 USB Full Speed Device Controller driver (DCD) options
-#
-# CONFIG_SAM34_UDP_REGDEBUG is not set
-
 #
 # AT91SAM3/4 Watchdog Configuration
 #
@ -265,7 +259,7 @@ CONFIG_WDT_MINTIME=2000
 CONFIG_WDT_THREAD=y
 CONFIG_WDT_THREAD_NAME="wdog"
 CONFIG_WDT_THREAD_INTERVAL=2000
-CONFIG_WDT_THREAD_PRIORITY=99
+CONFIG_WDT_THREAD_PRIORITY=220
 CONFIG_WDT_THREAD_STACKSIZE=512

 #
@ -280,9 +274,8 @@ CONFIG_ARCH_HAVE_IRQPRIO=y
 CONFIG_ARCH_HAVE_VFORK=y
 # CONFIG_ARCH_HAVE_MMU is not set
 # CONFIG_ARCH_NAND_HWECC is not set
-CONFIG_ARCH_IRQPRIO=y
+# CONFIG_ARCH_IRQPRIO is not set
 CONFIG_ARCH_STACKDUMP=y
-CONFIG_ARCH_USBDUMP=y
 # CONFIG_ENDIAN_BIG is not set
 # CONFIG_ARCH_IDLE_CUSTOM is not set
 CONFIG_ARCH_HAVE_RAMFUNCS=y
@ -438,7 +431,7 @@ CONFIG_PTHREAD_STACK_DEFAULT=4096
 #
 # Device Drivers
 #
-CONFIG_DISABLE_POLL=y
+# CONFIG_DISABLE_POLL is not set
 CONFIG_DEV_NULL=y
 CONFIG_DEV_ZERO=y
 # CONFIG_LOOP is not set
@ -473,14 +466,13 @@ CONFIG_MMCSD_SDIO=y
 # CONFIG_SDIO_MUXBUS is not set
 CONFIG_SDIO_BLOCKSETUP=y
 # CONFIG_MTD is not set
-# CONFIG_PIPES is not set
+CONFIG_PIPES=y
 # CONFIG_PM is not set
 # CONFIG_POWER is not set
 # CONFIG_SENSORS is not set
 # CONFIG_SERCOMM_CONSOLE is not set
 CONFIG_SERIAL=y
 # CONFIG_DEV_LOWCONSOLE is not set
-CONFIG_SERIAL_REMOVABLE=y
 # CONFIG_16550_UART is not set
 # CONFIG_ARCH_HAVE_UART is not set
 CONFIG_ARCH_HAVE_UART0=y
@ -510,6 +502,7 @@ CONFIG_ARCH_HAVE_USART1=y
 CONFIG_USART1_ISUART=y
 CONFIG_MCU_SERIAL=y
 CONFIG_STANDARD_SERIAL=y
+CONFIG_SERIAL_NPOLLWAITERS=2
 # CONFIG_SERIAL_TIOCSERGSTRUCT is not set
 CONFIG_UART0_SERIAL_CONSOLE=y
 # CONFIG_UART1_SERIAL_CONSOLE is not set
@ -521,7 +514,7 @@ CONFIG_UART0_SERIAL_CONSOLE=y
 #
 CONFIG_UART0_RXBUFSIZE=256
 CONFIG_UART0_TXBUFSIZE=256
-CONFIG_UART0_BAUD=912600
+CONFIG_UART0_BAUD=115200
 CONFIG_UART0_BITS=8
 CONFIG_UART0_PARITY=0
 CONFIG_UART0_2STOP=0
@ -533,7 +526,7 @@ CONFIG_UART0_2STOP=0
 #
 CONFIG_UART1_RXBUFSIZE=256
 CONFIG_UART1_TXBUFSIZE=256
-CONFIG_UART1_BAUD=921600
+CONFIG_UART1_BAUD=115200
 CONFIG_UART1_BITS=8
 CONFIG_UART1_PARITY=0
 CONFIG_UART1_2STOP=0
@ -545,7 +538,7 @@ CONFIG_UART1_2STOP=0
 #
 CONFIG_USART1_RXBUFSIZE=256
 CONFIG_USART1_TXBUFSIZE=256
-CONFIG_USART1_BAUD=921600
+CONFIG_USART1_BAUD=115200
 CONFIG_USART1_BITS=8
 CONFIG_USART1_PARITY=0
 CONFIG_USART1_2STOP=0
@ -553,49 +546,7 @@ CONFIG_USART1_2STOP=0
 # CONFIG_USART1_OFLOWCONTROL is not set
 # CONFIG_SERIAL_IFLOWCONTROL is not set
 # CONFIG_SERIAL_OFLOWCONTROL is not set
-CONFIG_USBDEV=y
-
-#
-# USB Device Controller Driver Options
-#
-# CONFIG_USBDEV_ISOCHRONOUS is not set
-# CONFIG_USBDEV_DUALSPEED is not set
-# CONFIG_USBDEV_SELFPOWERED is not set
-CONFIG_USBDEV_BUSPOWERED=y
-CONFIG_USBDEV_MAXPOWER=100
-# CONFIG_USBDEV_DMA is not set
-CONFIG_ARCH_USBDEV_STALLQUEUE=y
-CONFIG_USBDEV_TRACE=y
-CONFIG_USBDEV_TRACE_NRECORDS=256
-CONFIG_USBDEV_TRACE_STRINGS=y
-
-#
-# USB Device Class Driver Options
-#
-# CONFIG_USBDEV_COMPOSITE is not set
-# CONFIG_PL2303 is not set
-CONFIG_CDCACM=y
-# CONFIG_CDCACM_CONSOLE is not set
-CONFIG_CDCACM_EP0MAXPACKET=64
-CONFIG_CDCACM_EPINTIN=1
-CONFIG_CDCACM_EPINTIN_FSSIZE=64
-CONFIG_CDCACM_EPINTIN_HSSIZE=64
-CONFIG_CDCACM_EPBULKOUT=3
-CONFIG_CDCACM_EPBULKOUT_FSSIZE=64
-CONFIG_CDCACM_EPBULKOUT_HSSIZE=512
-CONFIG_CDCACM_EPBULKIN=2
-CONFIG_CDCACM_EPBULKIN_FSSIZE=64
-CONFIG_CDCACM_EPBULKIN_HSSIZE=512
-CONFIG_CDCACM_NWRREQS=4
-CONFIG_CDCACM_NRDREQS=4
-CONFIG_CDCACM_BULKIN_REQLEN=250
-CONFIG_CDCACM_RXBUFSIZE=1024
-CONFIG_CDCACM_TXBUFSIZE=1024
-CONFIG_CDCACM_VENDORID=0x0525
-CONFIG_CDCACM_PRODUCTID=0xa4a7
-CONFIG_CDCACM_VENDORSTR="NuttX"
-CONFIG_CDCACM_PRODUCTSTR="CDC/ACM Serial"
-# CONFIG_USBMSC is not set
+# CONFIG_USBDEV is not set
 # CONFIG_USBHOST is not set
 # CONFIG_WIRELESS is not set

@ -688,8 +639,8 @@ CONFIG_BUILTIN=y
 #
 # Standard C Library Options
 #
-CONFIG_STDIO_BUFFER_SIZE=64
-CONFIG_STDIO_LINEBUFFER=y
+CONFIG_STDIO_BUFFER_SIZE=0
+# CONFIG_STDIO_LINEBUFFER is not set
 CONFIG_NUNGET_CHARS=2
 # CONFIG_LIBM is not set
 # CONFIG_NOPRINTF_FIELDWIDTH is not set
@ -714,14 +665,7 @@ CONFIG_LIB_SENDFILE_BUFSIZE=512
 # Non-standard Library Support
 #
 CONFIG_SCHED_WORKQUEUE=y
-CONFIG_SCHED_HPWORK=y
-CONFIG_SCHED_WORKPRIORITY=192
-CONFIG_SCHED_WORKPERIOD=50000
-CONFIG_SCHED_WORKSTACKSIZE=2048
-CONFIG_SCHED_LPWORK=y
-CONFIG_SCHED_LPWORKPRIORITY=50
-CONFIG_SCHED_LPWORKPERIOD=50000
-CONFIG_SCHED_LPWORKSTACKSIZE=2048
+# CONFIG_SCHED_HPWORK is not set
 # CONFIG_LIB_KBDCODEC is not set
 # CONFIG_LIB_SLCDCODEC is not set

@ -753,6 +697,7 @@ CONFIG_BUILTIN_PROXY_STACKSIZE=1024
 # CONFIG_EXAMPLES_BUTTONS is not set
 # CONFIG_EXAMPLES_CAN is not set
 # CONFIG_EXAMPLES_CONFIGDATA is not set
+CONFIG_EXAMPLES_CPUHOG=y
 # CONFIG_EXAMPLES_CXXTEST is not set
 # CONFIG_EXAMPLES_DHCPD is not set
 # CONFIG_EXAMPLES_ELF is not set
@ -787,6 +732,7 @@ CONFIG_EXAMPLES_NSH_CXXINITIALIZE=y
 # CONFIG_EXAMPLES_RGMP is not set
 # CONFIG_EXAMPLES_ROMFS is not set
 # CONFIG_EXAMPLES_SENDMAIL is not set
+CONFIG_EXAMPLES_SERIALBLASTER=y
 # CONFIG_EXAMPLES_SERLOOP is not set
 # CONFIG_EXAMPLES_SLCD is not set
 # CONFIG_EXAMPLES_SMART_TEST is not set
@ -910,12 +856,10 @@ CONFIG_NSH_NESTDEPTH=3
 # CONFIG_NSH_DISABLE_LOOPS is not set
 # CONFIG_NSH_DISABLEBG is not set
 CONFIG_NSH_CONSOLE=y
-# CONFIG_NSH_USBCONSOLE is not set

 #
 # USB Trace Support
 #
-# CONFIG_NSH_USBDEV_TRACE is not set
 CONFIG_NSH_CONDEV="/dev/console"
 CONFIG_NSH_ARCHINIT=y

@ -1013,13 +957,6 @@ CONFIG_SYSTEM_STACKMONITOR_INTERVAL=2
 #
 # USB CDC/ACM Device Commands
 #
-CONFIG_SYSTEM_CDCACM=y
-CONFIG_SYSTEM_CDCACM_DEVMINOR=0
-CONFIG_SYSTEM_CDCACM_TRACEINIT=y
-CONFIG_SYSTEM_CDCACM_TRACECLASS=y
-CONFIG_SYSTEM_CDCACM_TRACETRANSFERS=y
-CONFIG_SYSTEM_CDCACM_TRACECONTROLLER=y
-CONFIG_SYSTEM_CDCACM_TRACEINTERRUPTS=y

 #
 # USB Composite Device Commands
@ -1032,15 +969,6 @@ CONFIG_SYSTEM_CDCACM_TRACEINTERRUPTS=y
 #
 # USB Monitor
 #
-CONFIG_SYSTEM_USBMONITOR=y
-CONFIG_SYSTEM_USBMONITOR_STACKSIZE=1024
-CONFIG_SYSTEM_USBMONITOR_PRIORITY=50
-CONFIG_SYSTEM_USBMONITOR_INTERVAL=2
-CONFIG_SYSTEM_USBMONITOR_TRACEINIT=y
-CONFIG_SYSTEM_USBMONITOR_TRACECLASS=y
-CONFIG_SYSTEM_USBMONITOR_TRACETRANSFERS=y
-CONFIG_SYSTEM_USBMONITOR_TRACECONTROLLER=y
-CONFIG_SYSTEM_USBMONITOR_TRACEINTERRUPTS=y

 #
 # Zmodem Commands